Smeg KSE90XT User's Manual
Contents
1. V2 V3 ce MAINTENANCE Grease filters CLEANING METAL SELF SUPPORTING GREASE FILTERS The filters must be cleaned every 2 months of operation or more frequently for particularly heavy usage and can be washed in a dishwasher Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time Wash the filters taking care not to bend them Allow them to dry before refitting When refitting the filters make sure that the handle is visible on the outside Activated charcoal filter Recirculation version REPLACING THE ACTIVATED CHARCOAL FILTER The filter is not washable and cannot be regenerated and must be replaced approximately every 4 months of operation or more frequently for particularly heavy usage Remove the metal grease filters Remove the saturated activate2. ese Omeg Instructions Manual Manual de instrucciones Manual de Instru es KSE90XT INDEX RECOMMENDATIONS AND SUGGESTIONS nens tuat 3 CHARAGTERIS HUS eene Se RD rada ea E 4 INSTALLATION A ubt Be t gh 5 USE cuu RR ERR DR PR ME 8 MAINTENANCE cosas to ba ei E ea de 9 INDICE CONSEJOS Y SUGERENCIAS sad bus iat aii a id 10 CARACTERISTICAS theta Plot a 11 INSTALACION S mera no eater ca a ri 12 Bs 15 MANTENIMIENTO iato too ate dare ii getestet t ta 16 INDICE CONSELHOS E SUGESTOES Aat 17 CARACTERISTICAS Cem eT aoe ee ENR Ne eee ey tae 18 Lars E ASI AS Na LM oe eas 19 UTILIZACAO EN PUR NO a a a a PERS 22 MANLITEN O 23 RECOMMENDATIONS AND SUGGESTIONS A The Instructions for Use apply to several versions of this appliance Accord ingly you may find descriptions of individual features that do not apply to your specific appliance INSTALLATION The manufacturer will not be held liable for any damages resulting from in correct or improper installation The minimum safety distance between the cooke
3. d carbon filter by releasing the fixing hooks Fit the new filter by hooking it into its seating Refit the metal grease filters Lighting LIGHT REPLACEMENT 40 W incandescent light Remove the metal grease filters Unscrew the bulbs and replace them with new ones having the same characteristics Replace the metal grease filters
4. eat this operation on the other side Drill 8 mm holes at all the centre points marked Insert the wall plugs 11 in the holes Fix the brackets using the 12a 4 2 x 44 4 screws supplied Insert the two screws 12a 4 2 x 44 4 supplied in the hood body fixing holes leaving a gap of 5 6 mm between the wall and the head of the screw Mounting the hood body Before attaching the hood body tighten the two screws Vr lo cated on the hood body mounting points Hook the hood body onto the screws 12a Fully tighten the support screws 12a Adjust the screws Vr to level the hood body Connections DUCTED VERSION AIR EXHAUST SYSTEM EDTA on ES When installing the ducted version connect the hood to the P us u ry chimney using either a flexible or rigid pipe 150 or 120 mm 1 na a M the choice of which is left to the installer y To install a 8 120 mm air exhaust connection insert the re ducer flange 9 on the hood body outlet Fix the pipe in position using sufficient pipe clamps not sup plied Remove possible charcoal filters RECIRCULATION VERSION AIR OUTLET Push fit connection 15 onto the hood body outlet Insert the connection extension pieces laterally 14 1 in connec tion 15 O Make sure that the outlet of the extension pieces 14 1 is O zontally and vertically aligned with the chimney outlets If this is not the case adjust the position by either reversing the con nection ext
5. ension pieces 14 1 and then reassemble as described previously Ensure that the activated charcoal filters have been inserted ELECTRICAL CONNECTION Connect the hood to the mains through a two pole switch hav ing a contact gap of at least 3 mm Remove the grease filters see paragraph Maintenance being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan Chimney assembly Upper chimney section Slightly widen the two sides of the upper chimney and hook them behind the brackets 7 2 1 making sure that they are prop erly housed e Secure the sides to the brackets using the 4 screws 12 2 9 x 9 5 supplied Lower chimney section Slightly widen the two sides of the section and hook them be tween the upper section and the wall making sure that they are properly housed Fix the sides of the bottom section to the hood body using the 2 screws 12c 2 9 x 9 5 supplied When installing the recirculation version fit the directional grills 8a 8b in their housings so that the directional symbols are at the top and towards the front of the hood Ensure that they are inserted correctly in the outlet connection piece 15 USE 2900 5 Vi v V3 5 LED LED Vi
6. nts Ref Q ty Product Components 1 1 Hood Body complete with Controls Light Blower Filters 2 Telescopic Chimney comprising 2 1 Upper Section 2 2 Lower Section 8a Right Air Outlet Grill 9 Reducer Flange 150 120 mm 14 1 Air Outlet Connection Extension 1 1 1 1 8b 1 Left Air Outlet Grill 1 2 1 15 Air Outlet Connection Ref Installation Components 721 2 Upper Chimney Section Fixing Brackets 11 6 Wall Plugs 12a 6 Screws 4 2 x 44 4 12c 6 Screws 2 9 x 9 5 Q ty Documentation 1 Instruction Manual INSTALLATION Wall drilling and bracket fixing N E c id 7 2 1 2 Wall marking Draw a vertical line on the supporting wall up to the ceiling or as high as practical at the centre of the area in which the hood will be installed Draw a horizontal line at 650 mm above the hob Place bracket 7 2 1 on the wall as shown about 1 2 mm from the ceiling or upper limit aligning the centre notch with the vertical reference line Mark the wall at the centres of the holes in the bracket Place bracket 7 2 1 on the wall as shown at X mm below the first bracket X height of the upper chimney section supplied aligning the centre notch with the vertical line Mark the wall at the centres of the holes in the bracket Mark a reference point as indicated at 116 mm from the vertical reference line and 320 mm above the horizontal reference line Rep
7. r top and the extractor hood is 650 mm some models can be installed at a lower height please re fer to the paragraphs on working dimensions and installation Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood For Class appliances check that the domestic power supply guarantees adequate earthing Connect the extractor to the exhaust flue through a pipe of minimum diame ter 120 mm The route of the flue must be as short as possible Do not connect the extractor hood to exhaust ducts carrying combustion fumes boilers fireplaces etc If the extractor is used in conjunction with non electrical appliances e g gas burning appliances a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas The kitchen must have an opening communicating directly with the open air in order to guar antee the entry of clean air USE The extractor hood has been designed exclusively for domestic use to elimi nate kitchen smells gt Never use the hood for purposes other than for which it has been designed c 650 mm min Neverleave high naked flames under the hood when it is in operation Adjust the flame intensity to direct it onto the bottom of the pan only making sure that it does not engulf the sides Deep fat fryers must be continuously monitored during use overheated oil can burst into flames Do not flamb
8. under the range hood risk of fire This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concern ing use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appli ance MAINTENANCE Switch off or unplug the appliance from the mains supply before carrying out any maintenance work Clean and or replace the Filters after the specified time period Fire hazard Clean the hood using a damp cloth and a neutral liquid detergent The symbol A on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product CHARACTERISTICS Dimensions max 1055 740 300 500mm 650mm Compone
Download Pdf Manuals
Related Search