Smeg ALFA41VEK Installation Manual
Contents
1. to 250 or hold START down for increments of 5 C Press STOP to move on to displaying the next parameter The display shows U Ct Press START to display the cooking time Press START or keep it pressed to increase the cooking time from 1 min to 99 min Press STOP to move on to displaying the next parameter The display shows H O Press START to increase the number of seconds of water infeed per minute from O to 5 where O means conventional fan mode cooking without the aid of humidification Press STOP to complete the editing operation The display shows UEnd The parameters set are now saved in the chosen program 4 8 Programmed preheating P9 This program which can be edited by the user allows the oven to be programmed to perform a preheating operation with the starting time temperature and program end time set as required 4 9 Setting programmed preheating The first step is to make sure that the oven s main clock is set to the correct time otherwise adjust it as described in the SETTING THE TIME section N B if the time has not been set flashing this program will not run Use the knob to select the programmed preheating program P9 The display shows PrEh Keep STOP pressed for 2 seconds The display shows a flashing On message program start time setting Press START or keep it pressed to increment the hours Press STOP to move on to setting the minutes 31 GBAE 32 Instructions f2. Err2 low voltage less than 160 volts 4 13 Technical notes If the power supply to the appliance fails at any time always return the knob to the 0 setting before running any programs 33 GBAE 34 A E S Instructions for the User ome 5 CLEANING AND MAINTENANCE Important never point jets of water straight at the oven do not use high pressure jets Before carrying out any operation disconnect the oven from the electricity supply 5 1 Cleaning stainless steel To keep stainless steel in good condition it must be cleaned regularly at the end of each day after allowing it to cool When cleaning and caring for stainless steel surfaces always use only specific products which do not contain abrasives or chlorine based acids Instructions for use pour the product onto a damp cloth and wipe over the surface then rinse thoroughly and dry with a soft cloth or chamois leather Never use metal scouring pads or sharp scrapers which will damage the surface Use ordinary non abrasive products for steel with the aid of wooden or plastic utensils if necessary Rinse thoroughly and dry with a soft cloth or chamois leather Instructions for the User 5 2 Cleaning the inside of the oven To keep the oven in good condition it must be cleaned regularly at the end of each day after allowing it to cool Remove all removable parts Remove the side runners by unscrewing the ring nut A and extract them through the
3. COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS lt i IF THE MAIN ELECTRICAL CONNECTION IS TO BE MADE BY MEANS OF A PLUG AND SOCKET THEY MUST BOTH BE OF THE SAME TYPE AND MUST BE CONNECTED TO THE POWER SUPPLY LEAD IN ACCORDANCE WITH THE RELEVANT REGULATIONS NEVER DISCONNECT THE PLUG BY PULLING ON THE CABLE NEVER OBSTRUCT THE OPENINGS PROVIDED FOR VENTILATION OR HEAT DISPERSAL IMMEDIATELY AFTER INSTALLATION CARRY OUT A QUICK TEST ON THE OVEN FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS MANUAL IF THE APPLIANCE FAILS TO OPERATE DISCONNECT IT FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF AFTER EACH USE OF THE OVEN ALWAYS CHECK THAT THE CONTROL KNOBS ARE TURNED TO 0 OFF E Pi Introduction GB IE NEVER PLACE FLAMMABLE OBJECTS IN THE OVEN IF IT SHOULD ACCIDENTALLY BE SWITCHED ON THIS MIGHT CAUSE A FIRE THE APPLIANCE BECOMES VERY HOT DURING USE OVEN GLOVES SHOULD ALWAYS BE WORN THE NAMEPLATE WITH THE TECHNICAL DATA SERIAL NUMBER AND MARK IS IN A VISIBLE POSITION ON THE BACK OF THE OVEN THIS NAMEPLATE MUST NEVER BE REMOVED THE APPLIANCE IS INTENDED FOR PROFESSIONAL USE BY TRAINED STAFF KEEP CHILDREN AT A SAFE DISTANCE AND NEVER ALLOW THEM TO PLAY WITH IT BEFORE USE WASH THE PANS WITH A SPECIAL OVEN WARE DETERGENT NEVER USE ABRASIVE PRODUCTS THE OVEN S SIZE IS CALCULATED FOR A MAXIMUM LOAD OF 3 5 KG BEFORE THE APPLI
4. increment them as before by pressing the START button When the correct time is set press the STOP button and the display will stop flashing 27 GB IE 28 Instructions for the User ome 4 3 Program selection This oven has 10 different cooking programs including 2 preset programs P1 P2 6 user editable programs for humidified fan mode cooking P3 to P8 1 preheating program with user editable temperature and start and end time P9 1 easy editable program for humidified fan mode cooking P10 The following table shows the parameters for each program Uprh Ut C UCt Program H O preheating cooking cooking start end temperature temperature time time P1 210 C 210 C 18 N A 5 0 minutes P2 240 C 240 C 9 N A 5 0 minutes P3 Editable Editable Editable N A Editable P4 Editable Editable Editable N A Editable P5 Editable Editable Editable N A Editable P6 Editable Editable Editable N A Editable P7 Editable Editable Editable N A Editable P8 Editable Editable Editable N A Editable P9 Editable N A N A Editable N A P10 Same as edited Editable Editable N A Editable Ut C 4 4 Presettings Programs The first two program selector knob settings are for the presetting cooking mode programs Use the knob to select one of the preset programs P1 P2 The display shows the parameters of the selected program cooking time temperature in degrees Centigrade program number and steam percentage in the cooking chamber e g
5. ANCE IS PUT INTO OPERATION ALL THE LABELS AND PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE THIS DIRECTIVE CONTAINS THE REGULATIONS GOVERNING THE COLLECTION AND RECYCLING OF DECOMMISSIONED APPLIANCES THROUGHOUT THE EUROPEAN UNION The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance and the use of non original spare parts 23 GB E CN o x CET a Ep A 24 Instructions for the Installer 2 INSTALLING THE OVEN The oven is designed for free standing installation on a horizontal work top It must be far enough from the wall behind it to allow easy access to the terminal board for connection of the power supply lead Installation must be carried out by a qualified engineer in compliance with the relevant EEC DIRECTIVES 2 1 Electrical connection Check that the power supply voltage and size are as specified on the nameplate on the back of the oven This nameplate must never be removed The oven is fitted with a HO7RN F three core cable for operation at 230V and power supply plug The power supply lead supplied is of 3 x 1 5 mnf three core HO7RN F type The power supply lead must be replaced by the manufacturer or an authorised service centre t
6. P1 Press START to confirm the start of the program The program starts performing the preheating stage the display shows PrEh When the preheating is complete a BEEP sounds to indicate that cooking can start Press START to start cooking If START is not pressed after the beep the temperature is held constant for about 10 minutes after which it will start to drop for a period up to a maximum time of 20 minutes counted from when the beep sounded After p Instructions for the User GB E this the oven switches off During this stage the display shows the parameters of the selected program N B although this is not recommended in terms of cooking quality the program can be started even before the preheating temperature is reached by pressing START During cooking the display shows the time left until the end of the cooking process and the temperature set During the last minute of cooking the display will only show the countdown from 60 to zero seconds end of cooking time When all the cooking time has passed a BEEP will sound for 20 seconds and the display will show End During these 20 seconds the user can extend the cooking time as required in manual mode as follows Press START the display will show tp00 From now on each pressure on the START key corresponds to one more minute s cooking up to 10 extra minutes are permitted Cooking will restart at the programmed temperature after 5 seconds Aft
7. Table of Contents GB E 1 PRECAUTIONS FOR SAFETY AND USE 22 2 INSTALLING THE OVEN 24 3 DESCRIPTION OF FRONT PANEL CONTROLS 26 4 USING THE OVEN 27 5 CLEANING AND MAINTENANCE 34 6 EXTRAORDINARY MAINTENANCE 36 INSTRUCTIONS FOR THE INSTALLER these are intended for the qualified engineer who is to install commission and test the appliance INSTRUCTIONS FOR THE USER these provide recommendations for use a description of the controls and the correct procedures for cleaning and maintaining the appliance 21 GB IE Introduction 1 PRECAUTIONS FOR SAFETY AND USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE TAKE GOOD ale CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE OVEN S LIFE CYCLE WE URGE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE OVEN INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS THIS OVEN IS INTENDED FOR PROFESSIONAL USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION COOKING AND HEATING FOODS ALL OTHER USES ARE TO BE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN THOSE STATED ABOVE E NEVER USE PACKAGING RESIDUES UNATTENDED IN THE HOME SEPARATE THE VARIOUS WASTE PACKAGING MATERIALS BY TYPE AND CONSIGN THEM TO THE NEAREST SEPARATE DISPOSAL CENTRE al THE APPLIANCE MUST BE CONNECTED TO EARTH IN
8. e of about 45 and remove it To reassemble fit the hinges C into their grooves then open the door fully to release the levers B The door can now be closed in the normal way 6 3 Oven door gasket To allow thorough cleaning of the oven the door gasket can be removed Before removing the gasket remove the oven door as described above Once the door has been removed lift the tangs at the corners as shown on the right 37
9. er these additional minutes the program repeats the cooking end procedure described above and after the 20 second BEEP the word End will flash for 20 minutes during which time the temperature will gradually fall stabilising at 100 C After 20 minutes the oven switches off 29 GBAE 30 Instructions for the User ome 4 5 Humidified fan mode cooking 5 programs which the user can edit for humidified fan mode cooking as preferred from P4 to P8 These programs for editing by the user allow the oven to be programmed to perform a cooking procedure with the parameters listed below set to requirements 4 6 Editing a program The user editable programs are programs P4 to P8 A number of parameters can be edited for each program e preheating temperature Uprh User pre heating e cooking temperature U t C User heating e cooking temperature U Ct User cooking time e n of seconds of steam of cooking chamber per minute H O To edit a program by entering the parameters as you prefer turn the knob to one of the programs from P4 to P8 The display shows to indicate that there are no cooking parameters present Keep STOP pressed for 2 seconds The display shows UprH Press START to display the pre heating temperature Each time START is pressed the temperature increments by 1 C from 50 to 250 or hold START down for faster increments Press STOP to move on to displayng the next parameter The di
10. hole in the rear B e Clean the oven shelves and side runners with hot water and non abrasive detergents rinse and dry 5 3 Door glazing The glass in the door should always be kept thoroughly clean Use absorbent kitchen roll remove stubborn dirt with a damp sponge and ordinary detergent 35 GB IE Instructions for the User PN 6 EXTRAORDINARY MAINTENANCE Occasionally the oven will require minor servicing procedures or the replacement of parts subject to wear and tear such as gaskets light bulbs etc The specific operations for each procedure of this kind are provided below Before carrying out any operation disconnect the oven from the we electricity supply 6 1 Changing the light bulb Replace the protective cover A Replace the light bulb B with another of the same type Replace the protective cover A Use only light bulbs approved for ovens T 300 C 36 a Instructions for the User 6 2 Removing the door Hinges with mobile riders Take hold of the two sides of the door with both hands close to the hinges C and lift the levers D Raise the door to an angle of about 45 and remove it To reassemble fit the hinges C into their grooves then lower the door into place and engage the levers D Hinges with mobile levers Completely open the door and take hold of it on both sides close to the hinges Use a finger to push the levers A forward and at the same time lift the door forming an angl
11. ng cooking This pipe must be left free of all obstructions Take care not to crush it 25 26 START BUTTON Use this button to set the time when turning on the appliance for the first time or after a power failure scroll through the preset programs and start cooking cycles STOP BUTTON Use this button to set the time when turning on the appliance for the first time or after a power failure edit programs and terminate cooking cycles DISPLAY Displays the current time the selected program its cooking parameters and the operating power PROGRAM SELECTION KNOB Turn this knob to set the cooking cycle with a preset program a Instructions for the User GB IE 4 USINGTHE OVEN 4 1 Precautions and General Advice When the oven is used for the first time it should be heated to the maximum temperature for long enough to burn off any oily residues left by the manufacturing process If you have to carry out any procedures on foods leave the door open for as short a time as possible to ensure the temperature inside the oven does not drop far enough to impair cooking results 4 2 Setting the time At first use or after a power failure the current time must be set The display will show a flashing 888 icon To set the current time hold down START STOP together until the display stops flashing Now press START to increment the hour display Once the current hour has been set press STOP to set the minutes and
12. o prevent all risks The power supply plug and wall socket must be of the same type in compliance with CEI standards Check that the power supply line is properly earthed The use of reductions adapters or junctions is not recommended 2 1 1 Safety thermostat The oven is fitted with a safety device tripped in case of a serious malfunction To reset the safety device call the after sales service The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance y GB E Instructions for the Installer pins eat 2 2 Levelling Level the oven by means of its four adjustable feet To make the adjustment undo the lock nut and unscrew the foot The adjuster screw travel is 10 mm 2 3 Connection to the water supply Connect the water inlet connection on the rear to a water supply outlet having gas threaded connection taking care to screw tightly to the hose If the water supply pipe is new or has been unused for a long time before making the connection turn the water on and allow it to flow out to ensure that it is clear and free from impurities Otherwise the water inlet may become fouled damaging the oven The oven must be supplied with water at a pressure between min 50 kPa and max 500 kPa 2 4 Steam vent pipe The rear of the oven is fitted with a pipe which vents the steam produced duri
13. or the User ome Press START to increment the minutes Press STOP to move on to displaying the next parameter The display shows UPrh Press START to display the preheating temperature Press START or keep it pressed to increase the preheating temperature from 30 to 250 N B We recommend setting the temperature slightly higher than the cooking program temperature itself so that the preheating phase of the selected program will last for the shortest possible time since the oven will automatically recognise the preheating temperature and indicate that it is ready for use for cooking as soon as possible Press STOP to move on to displaying the next parameter The display shows a flashing OFF message program switch off time setting Press START or keep it pressed to increment the hours Press STOP to move on to setting the minutes Press START per increment the minutes Press STOP to complete the editing operation The display shows UEnd The parameters set are now saved in the chosen program 4 10 How programmed preheating works If the above parameters are set correctly and only if the knob is set on P9 the oven will run the preheating program every day at the set time during the preheating the display will show the PrEh message and once the set temperature is reached it will be kept constant until the switch off OFF time set or until the user interrupts it by pressing the STOP button After STOP has been pre
14. splay shows U t C Press START to display the cooking temperature Press START or keep it pressed to increase the cooking temperature from 50 to 250 Press STOP to move on to displaying the next parameter The display shows U Ct Press START to display the cooking time Press START or keep it pressed to increase the cooking time from 1 min to 99 min Press STOP to move on to displaying the next parameter The display shows H O Press START to increase the number of seconds of water infeed per minute from O to 5 where O means conventional fan mode cooking without the aid of humidification Press STOP to complete the editing operation The display shows UEnd The parameters set are now saved in the chosen program Press START to display the parameters just set Press START again to run the program just edited Instructions for the User GB E 4 7 Modifying a previously edited program To modify one of the programs turn the knob to one of the programs from P4 to P8 edited previously The parameters saved earlier will appear on the display Keep STOP pressed for 2 seconds The display shows UprH Press START to increase the pre heating temperature Press STOP to move on to displayng the next parameter The display shows U t C Press START to display the cooking temperature Press START or keep it pressed to increase the cooking temperature each time START is pressed the temperature increments by 1 C from 50
15. ssed the oven is ready to run any cooking program 4 11 Manual mode cooking Use the knob to select the easy program P10 The special feature of this user editable program is that the cooking parameters set are not retained in the memory when the knob is turned to any other position This means that an empty program is always immediately available for quick easy editing Instructions for the User GB E 4 11 1 How to use this program Use the knob to select the easy program P10 The display shows to indicate that there are no cooking parameters present Press START or keep it pressed to increase the preheating temperature from 30 to 250 Press STOP to move on to displaying the next parameter The display shows H O Press START to increase the number of seconds of water infeed per minute from O to 5 where 0 means conventional fan mode cooking without the aid of humidification Press STOP to increase the number of minutes of cooking N B if a cooking time of 99 minutes is set the cooking time will be infinite meaning that cooking can only be stopped in manual mode by ending the program Release STOP and preheating will start automatically after 5 seconds N B When the cooking process is over to repeat the same program do not turn the knob and press START again 4 12 Possible error messages on the display The display is able to show two different types of error Err1 probe failure
Download Pdf Manuals
Related Search