Home

Smeg ALFA135V6 Owner's Manual

1. The rear of the oven is fitted with a pipe which vents the steam produced during cooking This pipe must be left free of all obstructions Take care not to crush it 26 Instructions for the User 3 DESCRIPTION OF CONTROLS START BUTTON Use this button to set the time when turning on the appliance for the first time or after a power failure scroll through preset programs and start cooking cycles STOP BUTTON Use this button to set the time when turning on the appliance for the first time or after a power failure scroll through preset programs and terminate cooking cycles DISPLAY Displays the current time the selected program the cooking parameters of the selected program and for 90 cm models only the operating power PROGRAM SELECTION KNOB Turn this knob to set the cooking cycle with a preset program 27 28 Instructions for the User 4 USING THE OVEN 4 1 Precautions and General Advice When the oven is used for the first time it should be heated to the maximum temperature for long enough to burn off any oily residues left by the manufacturing process If you have to carry out any procedures on foods leave the door open for as short a time as possible to ensure the temperature inside the oven does not drop far enough to impair cooking results To avoid unpleasant contact with any steam inside the oven open the door in two stages hold it half open about 5 cm for 4 5 seconds th
2. power supply line must be fitted with an omnipolar breaking device with contact breaking gap of at least 3 mm located in an easily accessible position close to the appliance itself WARNING if the mains voltage drops below 190 VAC there might be an impairment of the oven s performance this is not due to the appliance itself 25 RIE Instructions for the Installer X 2 2 Safety thermostat The oven is fitted with a safety device tripped in case of a serious malfunction To reset the safety device call the after sales service caused by failure to comply with the above regulations or deriving from The manufacturer declines all responsibility for injury or damage tampering with even just one part of the appliance 2 3 Levelling Level the oven by means of its four adjustable feet To make the adjustment undo the lock nut and unscrew the foot The adjuster screw travel is 10 mm 2 4 Connection to the water supply Connect the water inlet connection on the rear to a water supply outlet having 34 gas threaded connection taking care to screw tightly to the hose If the water supply pipe is new or has been unused for a long time before making the connection turn the water on and allow it to flow out to ensure that it is clear and free from impurities Otherwise the water inlet may become fouled damaging the oven The oven must be supplied with water at a pressure between min 50 kPa and max 500 kPa 2 5 Steam vent pipes
3. temperature Press START or keep it pressed to increase the cooking temperature each time START is pressed the temperature increments by 1 C from 50 to 300 or hold START down for increments of 5 C Press STOP to move on to displaying the next parameter The display shows U Ct Press START to display the cooking time Press START or keep it pressed to increase the cooking time from 1 min to 99 min Press STOP to move on to displaying the next parameter The display shows U Ht only if Ut C is set gt 150 C Press START to display the humidification cycles Press START or keep it pressed to increase the number of humidification cycles from O to 6 cycles where 0 means conventional fan mode cooking without the aid of humidification Press STOP to complete the program editing procedure The display shows UEnd The parameters set are now saved in the chosen program 4 9 Manual cooking Use the knob to select the manual program The special feature of this user editable program is that the cooking parameters set are not retained in the memory when the knob is turned to any other position This means that an empty program is always immediately available for quick easy editing Instructions for the User 4 9 1 How to use this program Use the knob to select the manual program The display shows to indicate that there are no cooking parameters present and the number of the program P10 Press START
4. the knob to one of the programs from P1 to P14 The display shows the parameters contained in the selected program Hold down STOP for 2 seconds A beeper sounds to indicate that the editing mode has been accessed and the message Ut C appears on the display Press START to display the cooking temperature Press START or keep it pressed to increase the cooking temperature each time START is pressed the temperature increments by 1 C from 50 to 300 or hold START down for increments of 5 C N B humidification cycles U Ht can only be edited if Ut C is set at a temperature above 150 C Press STOP to move on to displaying the next parameter The display shows U Ct Press START to display the cooking time Press START or keep it pressed to increase the cooking time from 1 min to 99 min Press STOP to move on to displaying the next parameter The display shows U Ht only if Ut C is set gt 150 C Press START to display the humidification cycles Press START or keep it pressed to increase the number of humidification cycles from O to 6 cycles where 0 means conventional fan mode cooking without the aid of humidification Instructions for the User Press STOP to complete the program editing procedure The display shows UEnd The parameters set are now saved in the chosen program Press START to display the parameters just set Press START again to run the program just edited 4 7 Humidified fan mode cooking U
5. 1 2 3 4 5 6 Table of Contents PRECAUTIONS FOR SAFETY AND USE 22 INSTALLING THE OVEN 24 DESCRIPTION OF CONTROLS 27 USING THE OVEN 28 CLEANING AND MAINTENANCE 34 EXTRAORDINARY MAINTENANCE 36 INSTRUCTIONS FOR THE INSTALLER these are intended for the qualified engineer who is to install commission and test the appliance INSTRUCTIONS FOR THE USER these provide recommendations for use a description of the controls and the correct procedures for cleaning and maintaining the appliance 21 4 gt S 22 Introduction 1 PRECAUTIONS FOR SAFETY AND USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE OVEN S LIFE CYCLE WE URGE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE OVEN INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS THIS OVEN IS INTENDED FOR PROFESSIONAL USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION COOKING AND HEATING FOODS ALL OTHER USES ARE TO BE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN THOSE STATED ABOVE NEVER LEAVE PACKAGING RESIDUES UNATTENDED IN THE HOME SEPARATE THE VARIOUS PACKAGING MATERIALS BY TYPE AND CONSIGN THEM TO THE NEAREST SEPARATE DISPOSAL CENTRE THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WIT
6. H ELECTRICAL SYSTEM SAFETY REGULATIONS IF THE MAIN ELECTRICAL CONNECTION IS TO BE MADE BY MEANS OF A PLUG AND SOCKET THEY MUST BOTH BE OF THE SAME TYPE AND MUST BE CONNECTED TO THE POWER SUPPLY LEAD IN ACCORDANCE WITH THE RELEVANT REGULATIONS NEVER DISCONNECT THE PLUG BY PULLING ON THE CABLE NEVER OBSTRUCT THE OPENINGS PROVIDED FOR VENTILATION OR HEAT DISPERSAL IMMEDIATELY AFTER INSTALLATION CARRY OUT A QUICK TEST ON THE OVEN FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS MANUAL IF THE APPLIANCE FAILS TO OPERATE DISCONNECT IT FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF AFTER EACH USE OF THE OVEN ALWAYS CHECK THAT THE CONTROL KNOBS ARE TURNED TO 0 OFF Introduction NEVER PLACE FLAMMABLE OBJECTS IN THE OVEN IF IT SHOULD ACCIDENTALLY BE SWITCHED ON THIS MIGHT CAUSE A FIRE THE APPLIANCE BECOMES VERY HOT DURING USE OVEN GLOVES SHOULD ALWAYS BE WORN THE NAMEPLATE WITH THE TECHNICAL DATA SERIAL NUMBER AND MARK IS IN A VISIBLE POSITION ON THE BACK OF THE OVEN THIS NAMEPLATE MUST NEVER BE REMOVED THE APPLIANCE IS INTENDED FOR PROFESSIONAL USE BY TRAINED STAFF KEEP CHILDREN AT A SAFE DISTANCE AND NEVER ALLOW THEM TO PLAY WITH IT THE HARDNESS OF THE WATER USED FOR STEAM COOKING MUST NOT EXCEED 10 11 F USE TAP WATER TREATED WITH A PURIFIER SOFTENER SYSTEM THE OVEN S SIZE IS CALCULATED FOR A MAXIMUM LOAD OF 7 KG THIS APPLIANCE IS MAR
7. KED ACCORDING TO THE EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE THIS GUIDELINE IS THE FRAME OF A EUROPEAN WIDE VALIDITY OF RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT BEFORE THE APPLIANCE IS PUT INTO OPERATION ALL THE LABELS AND PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance and the use of non original spare parts 23 Saas Instructions for the Installer 2 INSTALLING THE OVEN X RA The oven is designed for free standing installation on a horizontal work A top It must be far enough from the wall behind it to allow easy access to cs the terminal board for connection of the power supply lead Installation must be carried out by a qualified engineer in compliance with the relevant EEC DIRECTIVES 2 1 Electrical connection removed The oven is fitted with a HO7RN F three core cable for operation at 240 240V For operation at 380 415V2N or 380 415V3N the power supply cable has to be replaced and the connection to the terminal board modified The terminal board can be accessed by removing the panel on the back of the oven 24 Check that the power supply voltage and size are as specified on the nameplate on the back of the oven This name
8. eaning of the oven the door gasket can be removed Before removing the gasket remove the oven door as described above Once the door has been removed lift the tangs at the corners as shown on the right 37
9. en open it completely 4 2 Inside lights The inside lights are turned on by turning the thermostat knob 4 3 Setting the time At first use or after a power supply failure the current time has to be set nnn i The YUU symbol will flash on the display To set the current time hold down START STOP together until the display stops flashing Now press or hold down START to increment the hour display Once the current hour has been set press STOP to set the minutes and increment them as before by pressing the START button When the correct time is set press the STOP button and the display will stop flashing 4 4 Setting the power After having set the time as described above and pressed the STOP button to confirm the setting the display will show P8 3 maximum power absorption 8 3 kW if the oven is connected to a three phase power supply or P5 5 maximum power absorption 5 5 kW if the power supply is single phase Press START repeatedly to scroll through the power absorption settings available P8 3 P5 5 or P3 0 for three phase power connection P5 5 or P3 0 for single phase power connection After selecting the appropriate power press STOP to confirm the setting N B This power setting operation only has to be carried out the first time the oven is connected The value set is saved and automatically used whenever the oven is switched on after this To modify this setting or the P1 P2 P3 P14 RIS Instruct
10. he end of each day after allowing it to cool Remove all removable parts ee Remove the side runners by removing the hook C from the hole or pin Coy aN D depending on the model and the pin A from the hole B on the fs FY bottom of the oven e Clean the oven shelves and side runners with hot water and non abrasive detergents rinse and dry 5 3 Door glazing The door pane of glass should always be kept thoroughly clean Use absorbent kitchen roll remove stubborn dirt with a damp sponge and ordinary detergent 35 36 o Instructions for the User 6 EXTRAORDINARY MAINTENANCE Occasionally the oven will require minor servicing procedures or the replacement of parts subject to wear and tear such as gaskets light bulbs etc The specific operations for each procedure of this kind are provided below Before carrying out any operation disconnect the oven from the electricity supply 6 1 Changing the light bulb Remove the protective cover A Replace the bulb B with another of the same type Replace the protective cover A OAN N Instructions for the User 6 2 Removing the door Open the door completely and insert the pins supplied into the holes from the inside Close the door to an angle of about 45 and lift it off To reassemble fit the hinges into their grooves then lower the door into place and extract the pins 6 3 Oven door gasket To allow thorough cl
11. he display is able to show two different types of error 4 12 1 Err3 This message appears whenever the software detects a sensor malfunction 4 12 2 Err1 This message appears whenever the software detects that the sensor connector is not properly connected to the electronic circuit board or has short circuited 33 Instructions for the User o 5 CLEANING AND MAINTENANCE Important AN never point jets of water straight at the oven and do not use high pressure water cleaners Before carrying out any operation disconnect the oven from the electricity supply K 5 1 Cleaning stainless steel 3 To keep stainless steel in good condition it must be cleaned regularly at EN the end of each day after allowing it to cool AN EN When cleaning and caring for stainless steel surfaces always use only specific products which do not contain abrasives or chlorine based acids Instructions for use pour the product onto a damp cloth and wipe over the surface then rinse thoroughly and dry with a soft cloth or chamois leather Never use metal scouring pads or sharp scrapers they will damage surfaces Use ordinary non abrasive products for steel with the aid of wooden or plastic utensils if necessary P Rinse thoroughly and dry with a soft cloth or chamois leather B CF _ S Instructions for the User 5 2 Cleaning the inside of the oven o To keep the oven in good condition it must be cleaned regularly at t
12. ions for the User time press START STOP together to return to the point described in section 4 3 Setting the time 4 5 Program selection This oven has 15 different cooking programs including 14 user editable programs for humidified fan mode cooking P1 to P14 1 manual editable program for fan mode cooking The following table shows the parameters for each program Uprh Ut C U Ct U Ht preheating cooking cooking time humidification temperature temperature time Same as Preset 185 C Preset 16 Editable if edited Ut C Ut C gt 150 Same as Preset 190 C Preset 15 Editable if edited Ut C Ut C gt 150 Same as Editable Editable Editable if edited Ut C Ut C gt 150 Same as Editable Editable N A edited Ut C 4 6 Humidified cooking The humidified fan mode cooking programs the user is able to edit are from P1 to P14 A number of parameters can be edited for each program e cooking temperature U t C User heating e cooking time U Ct User cooking time e humidification cycles U Ht User humidity time See cycle examples below 29 Steam O Z ge oN Instructions for the User z z G 2 2 N v Pre Pra 5 5 Steam E a V pE 5 H a 10 minutes 0 10 0 Cooking cooking t ti me preset Start of eee humidification cycle Start of cooking 30 To edit a humidified fan mode program by entering the parameters exactly as required turn
13. ly show the countdown from 60 to zero seconds end of cooking time When all the cooking time has passed a beep and the flashing message End will indicate that cooking is over Once a cooking operation has finished the user can extend the cooking time exactly as required in manual mode as follows Press START the display will show tp00 From now on each pressure on the START key corresponds to one more minute s cooking up to 10 extra minutes are permitted Cooking will restart at the programmed temperature after 5 seconds After these additional minutes the program repeats the cooking end procedure described above and word End will flash for 20 minutes during which time the temperature will gradually fall stabilising at 100 C for cooking processes at 100 C or 31 32 Instructions for the User o above or at the program temperature for cooking operations at below 100 C After 20 minutes the oven switches off N B during preheating and cooking whenever the door is opened the message door will appear on the display and a beep will sound to warn the user that the door must be closed while these operations are in progress 4 8 Modifying a previously edited program To modify one of the programs turn the knob to one of the programs from P1 to P14 edited previously The parameters saved earlier will appear on the display Hold down STOP for 2 seconds The display shows U t C Press START to display the cooking
14. or keep it pressed to increase the cooking temperature each time START is pressed the temperature increments by 1 C from 50 to 300 or hold START down for increments of 5 C Press STOP or keep it pressed to increase the cooking time from 1 min to 99 min if you require a timed cooking operation or set InF if an indefinite cooking time is required Release STOP and preheating will start automatically after 5 seconds the oven will preheat to the set cooking temperature N B When the cooking process is over to repeat the same program do not turn the knob and press START again 4 10 Rapid cooling The oven has a special function which allows its interior to be cooled quickly To activate this function turn the function selector to 0 open the door and press the START key for at least 2 seconds The fans inside the oven will come into operation with the heating elements off To stop the function press the STOP key 4 11 Key to the oven s beep sounds All the beep sounds the oven emits are different from each other in order to allow the user to identify exactly what the oven is doing Parameter setting modification menu 1 single beep End of preheating and pause before start of cooking 5 beeps followed by a pause of 2 seconds Cooking start 2 single beeps Door open during preheating and cooking continuous beep End of cooking 3 beeps followed by pause of 4 seconds 4 12 Possible error messages on the display T
15. plate must never be DIAGRAMMA COLLEGAMENTI CONNECTION DIAGRAM DIAGRAMA CONEXIONES DIAGRAMA DE LIGACODES L1 N COLLEGAMENTO EFFETUATO IN FABBRICA CONNECTION DONE IN THE FACTORY CONEXION EFECTUADA EN LA FABRICA LIGACAO EFECTUADA NA FABRICA 123458 ipl ie e 400 415V 2N L1 L2 N 123 45 Li L2 L3 N X df Instructions for the Installer The power supply lead supplied is of 220 240V __ 4mm HO7RN F type gauge 3 x 4 mn i For operation at 380 415V2N or 380 m 415V3N the power supply cable has to be e imm replaced with one of HO7RN F type The gauge of the wires in the new cable must be 380 415V 2N mw at least 2 5 1 5 mmr 4 x 2 5 mm 5 x 1 5 mm bearing in mind that the earth wire yellow green must be at least 20 mm longer at the end for connection to the oven m 20 mm 380 415V 3N 1 5 mm 20 mm In case of connection to the electrical mains by means of socket and pin the connection must be completed with a three pin plug of suitable rating 25A or for operation at 380 415V2N 380 415V3N a five pin plug 16A The power supply plug and wall socket must be of the same type in compliance with CEI standards Check that the power supply line is properly earthed The use of reductions adapters or junctions is not recommended If a permanent connection to the electrical mains is used the appliance s
16. se the knob to select one of the preset programs P1 P14 The display shows the parameters of the selected program Press START to confirm the start of the program The program starts performing the preheating stage the display shows PrEh When the preheating is complete a beep sounds to indicate that cooking can start and the message PrEh flashes on the display Keep START pressed for a few seconds to start cooking another BEEP sounds to signal the switch from preheating to cooking If START is not pressed after the beep the temperature is held constant for about 10 minutes after which it will start to drop for a period up to a maximum time of 20 minutes counted from when the beep sounded After this the oven switches off N B although this is not recommended in terms of cooking quality the program can be started even before the preheating temperature is reached by keeping START pressed for a few seconds During cooking the display shows the time left until the end of the cooking process the temperature set the number of humidification cycles set if any and the number of the program being used in alternation While cooking is in progress only water can be delivered to the cooking chamber by operating the intake valve in manual mode To do this simply keep START pressed for at least one second When the button is released the water intake will be cut off During the last minute of cooking the display will on

Smeg ALFA135V6 Owner's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents