Smeg A11A-5 Instructions for Installation and Use
Contents
1. FUNCTION SWITCH THERMOSTAT SWITCH FROM 50 TO 250 C Ensures uniform heat distribution with greater heat penetration into the food Food will be lightly browned on the outside and remain soft inside Keep the oven door closed during cooking 9 5 Defrosting m r FUNCTION SWITCH THERMOSTAT SWITCH IN POSITION 0 The flow of air produced by the fan ensures quicker defrosting The air circulating inside the oven is at room temperature The advantage of defrosting at room temperature is that it does not alter e the taste and appearance of the food 26 e Instructions for the user 9 6 Spit cooking FUNCTION SWITCH PEE r THERMOSTAT SWITCH FROM 50 TO 250 C tds Prepare the spit with the food blocking fork screws A Insert frame B into the third guide from the bottom Remove handle D and position the spit shaft so that pulley E is guided on the link of frame B in the right side Insert the drip tray into the oven as far as it will go until the tip of the rod is in line with the hole C Now rock the frames B to insert the tip of the rod into the drive connection C of the rotisserie motor on the side of the oven Pour a bit of water into the pan to avoid smoke from the dripping Keep the oven door closed during cooking It is normal for the thermostat light to go on and off intermittently during cooking This indicates the temperature inside the oven is regular CAUTION the frames B must be fitted as sho2. the surface shall be protected in accordance with Clause 5 12 1 2 to a height C of not less than 150 mm above the hob for the full dimension width or depth of the cooking surface area Where the cooking appliance is fitted with a splashback protection of the rear wall is not required Additional requirements for Freestanding and Elevated Cooking Appliaces Measurements D amp E Where D the distance from the periphery of the nearest burner to a horizontal combustible surface is less than 200 mm then E shall be 10 mm or more or the horizontal surface shall be above the trivet See insets above NOTES 1 Requirement 3 does not apply to a freestanding or elevated cooking appliance which is designed to prevent flames or the cooking vessels from extending beyond the periphery of the appliance 2 The cooking surface area is defined as that part of the appliance where cooking normally takes place and does not include those parts of the appliance containing control knobs For definition of hob see Clause 1 4 64 For definition of trivet see Clause 1 4 109 Consideration is to be given to window treatments when located near cooking appliances See Clause 5 3 4 Q w 10 Instructions for the installer 2 5 Instruction for wall fixing 1 Fix the screw to the wall and hook the chain B 2 Hook the chain to the hole positioned at the rear of the cooker by the gas pipe A 3 Once the chain is in position pu
3. 00 N 9 W AO N gt 0 12 Contents INSTRUCTIONS FOR SAFE AND PROPER USE INSTALLATION OF THE APPLIANCE ADAPTATION TO DIFFERENT TYPES OF GAS FINAL OPERATIONS DESCRIPTION OF CONTROLS USE OF THE COOKING HOB USE OF THE OVEN AVAILABLE ACCESSORIES COOKING HINTS CLEANING AND MAINTENANCE EXTRAORDINARY MAINTENANCE PROBLEMS AND CAUSES and maintenance of the appliance 11 13 14 20 22 23 24 28 31 33 INSTRUCTIONS FOR THE INSTALLER these are for the qualified technician who must carry out a suitable check of the gas system install the appliance set it functioning and carry out an inspection test INSTRUCTIONS FOR THE USER these contain user advice description of the commands and the correct procedures for cleaning Introduction 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND li THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKER ALSO KEEP THE SERIES OF NOZZLES SUPPLIED INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT REGULATIONS IN FORCE THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS COOKING AND HEATING UP OF FOOD ALL OT
4. 3 9 1 3 0 90 Semi rapid 7 5 1 6 1 20 Rapid 12 2 7 1 55 Wok 15 5 8 1575 Fish pan 7 8 2 9 1 26 3 3 Arrangement of burners on cooking hob n BURNERS Auxiliary sh di Semi rapid zd dr Wok TN AR Fish pan Q GQ N 12 Instructions for the installer 4 FINAL OPERATIONS After replacing the nozzles reposition the flame spreader crowns the burner caps and the grids After adjustment to a different kind of gas from the one for which the cooker has been tested replace the plate inside the storage compartment with one corresponding to the new kind of gas This plate can be obtained from your nearest Authorised Assistance Centre 4 1 Adjustment of minimum for natural gas Light the burner and take it to the minimum Remove the gas tap knob and turn the adjustment screw inside or at the side of the tap Re shaft depending on the model until there is a ts regular minimum flame Replace the knob and check burner flame stability rapidly turning the knob from maximum to minimum position the 5 flame should not go out Repeat the operation on 9s all the gas taps SAEs 4 2 Positioning and levelling of the appliance Having carried out the electricity and gas hook up level the appliance using the four adjustable legs 4 3 Lubrication of gas taps With time it may happen that the gas taps get blocked and hard to turn Clean them inside and re grease them This operation must be done by an authorise
5. be used with Chinese woks Each knob corresponds to the burner indicated The E appliance is equipped with an electric lighting device ERES To light the burners press and turn the knob anticlockwise to the large flame symbol A Keep the knob pressed for about 2 seconds to let the thermocouple heat up If the burner turns off when the knob is released it means that the thermocouple isnt hot enough Repeat ignition and keep the knob pressed longer Once the burner has been ignited the flame can be regulated as required Always check that the control knobs are in the position O off when you finish using the hob If the burners turn off accidentally a safety device will trip after about 20 seconds to cut off gas flow even with the gas tap open 20 Instructions for the user 6 2 Practical advice for using the cooking hob burners For better use of the burners and lower gas consumption use covered containers that are proportional in size to the burner to prevent the flame from licking the sides see paragraph 6 3 Diameter of containers When water reaches the boiling point lower the flame so that it doesn t overflow To avoid burns or damage to the hob all recipients or griddle plates must be placed within the perimeter of the cooking hob All containers have to have a flat and smooth bottom When using fats or oils be extremely careful that they don t overheat and catch fire If the flame accidentally goes out
6. crowns and burners are all removable To remove the flame separating crown of the fish hob loosen the two screws exposed after having removed the cap Wash all parts with warm water and non abrasive detergent taking care to remove all tough spots Wait for all parts to be fully dry before remounting Replace the flame spreader crowns checking that they are positioned in their housing with their respective caps taking care that flame spreader holes A correspond to the spark plugs and the thermocouples 10 2 3 Ignition plugs and thermocouples To work well the ignition plugs and thermocouples must E always be very clean Check them frequently and clean gt them with a wet rag if necessary Any dry residue should be removed with a toothpick or a needle 10 8 Cleaning of the oven For best oven upkeep clean regularly after having allowed to cool Take out all removable parts Detach the side guides by unscrewing ring nut A and sliding out of the rear hole B Ami 2 d E DO NOT USE A STEAM JET FOR CLEANING THE INSIDE OF THE OVEN Clean the oven grill and side guides with hot water and non abrasive detergent Rinse and dry 29 30 Instructions for the user For easier cleaning the storage drawer underneath the oven can be completely removed Pull it right out and raise the front as for an ordinary drawer On some models once the drawer has been pulled completely out the two tabs have to be pushed up a
7. of the cooking time is reached the timer will switch off the oven heating elements the beeps will start and the numbers on the dial will flash The cooking time can also be reset by deleting the program set pressing the central key for 1 or 2 seconds will delete the time set and the oven will have to be switched off by hand Caution cooking times of more than 6 hours cannot be set Instructions for the user Cooking start as well as setting a cooking duration time the user can also set the cooking start time up to 12 hours after the current time To set the cooking start end time proceed as follows Set the cooking duration time as described in the previous point Within 6 7 seconds after the last time the or keys are pressed press the M key to set the cooking start time The display will show the current time with the inside segments indicating the cooking end time illuminated Use the cooking start time 6 7 seconds after the last time a key is pressed the display will show the current time and the cooking start and end times indicated by the illuminated inside segments The segments on the display will be constantly on until the current time is the same as the cooking start time as soon as the current time reaches the cooking start time set all the inside segments will start to flash indicating that the oven has started cooking When the end of the cooking time is reached the timer will s
8. turn off the control knob and wait at least 1 minute before trying to re light the burner 6 3 Diameter of containers ARUN sa EM UU 3 3 mK TER 1 Asaay Semi rapid Rapid PRAGA dE ET ds min and max in cm 12 14 16 20 18 26 20 26 use special oval shaped pan 21 22 va A Instructions for the user 7 USE OFTHE OVEN The user has only to press the central key for 1 2 seconds to enable use of the oven on first use or after a power blackout 7 1 Warnings and general advice Before using the oven for the first time pre heat it to maximum temperature 250 C long enough to burn any manufacturing oily residues which could give the food a bad taste To prevent any steam in the oven creating problems open the door in two stages half open _ open To access food always leave the door I open as short a time as possible to prevent the 7 the food LS 7 2 Oven Light lt 5 cm approx for 4 5 seconds and then fully x F temperature in the oven from falling and ruining A It comes on when the function switch knob is turned to any position 7 3 Storage drawer The storage drawer is at the bottom of the cooker underneath the oven For access pull the bottom of the door Never store inflammable materials such as rags paper or the like The compartment is intended only for holding the metal accessories of the range Never open the storage compartment when the oven is on
9. HER USES ARE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT SEPARATE THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE LC IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED I ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES 1 IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW SHOULD THE APPLIANCE NOT FUNCTION DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION ZERO OFF WHEN YOU FINISH USING THE HOB NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN THEY COULD BE ACCIDENTALLY LIGHTED AND CAUSE FIRES DURING USE THE APPLIANCE BECOMES VERY HOT TAKE CARE NOT TO i TOUCH THE HEATING ELEMENTS INSIDE THE OVEN DO NOT INSTALL THIS APPLIANCE ON A RAISED PLATFORM Introduction THE I D PLATE WITH TECHNICAL DATA REGISTRATION NUMBER AND BRAND NAME IS POSITIONED VISIBLY IN THE STORAGE COMPARTMENT THE PLATE MUST NOT BE REMOVED DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE COOKING HOB GRIDS NEVER USE THE COOKING HOB AS A WORK SURFACE DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE OUTER PERIMETER OF THE HOB THE APPLIANCE IS DESIGNED FOR USE BY ADULTS DO NOT ALLO
10. W CHILDREN TO GO NEAR OR PLAY WITH IT DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS INOPERATION THIS APPLIANCE IS DESIGNED FOR COOKING FOOD AND IT SHALL NOT BE USED AS A SPACE HEATER REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE COLLECTION CENTRE The manufacturer declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance or by the use of non original spares lt A A Instructions for the installer 2 INSTALLATION OF THE APPLIANCE It is the law that all gas appliances are installed by authorised persons Clearance around the cooker must comply with the requirements ol AS5601 2 1 Electrical connection Make sure that the power line voltage matches the specifications indicated on the rating plate located inside the storage compartment This rating plate must never be removed On the power line install a two pole cut off device with contact cut off distance greater than or equal to 3 mm located in an easily accessible position near the unit If the power cable is replaced the wire 1 5 mm section on the new cable must not be less than 1 5 mm 3 x 1 5 cable keeping in mind that the end to be connected to the hob must have the ground wire yellow green longer by at least 20 mm Use only the special cables available at our Service Centres 20 mm The manufacture
11. and still hot The temperature inside may be very high Instructions for the user 8 AVAILABLE ACCESSORIES The oven features 4 support positions for plates and racks of different height Oven grill for cooking food on plates small cakes roasts or food requiring light grilling Plate grill for placing above plate for cooking foods that might drip Oven plate useful for catching fat from foods on the grill above Pastry plate for baking cakes pizza and oven desserts Roasting spit useful for cooking chicken sausages and anything else requiring uniform cooking over the whole surface Spit supports to be inserted in the holes of the oven plate before mounting the roasting spit Accessories on Request You can order the lower base through Authorised Assistance Centres 23 24 A A Instructions for the user 9 COOKING HINTS During cooking do not cover the bottom of the oven with aluminium or tin foil and do not place pans or oven trays on it as this may damage the enamel coating If you wish to use greaseproof paper place it so that it will not interfere with the hot air circulation inside the oven Keep the oven door closed during cooking 9 1 Traditional cooking FUNCTION SWITCH THERMOSTAT SELECTOR SWITCH FROM wo 50 TO 250 C This traditional cooking method in which heat comes from above and below is suitable for cooking food on a single level You have to pre he
12. at the oven until the set temperature is reached Place the food in the oven only after the thermostat indicator light has turned off very fatty meats may be put in when the oven is still cold Put frozen meat in immediately without waiting for it to thaw The only precaution you need to take is to set the temperature about 20 C lower and cooking time about 1 4 longer than you would for fresh meat Use high rim pans to prevent fat splashing and dirtying the sides of the oven we Instructions for the user 9 2 Hot air cooking m ele ee FUNCTION SWITCH e THERMOSTAT SELECTOR SWITCH FROM Gs 50 TO 250 C This system is suitable for cooking on several levels including different types of food fish meat etc without the tastes and smells mingling Air circulation in the oven ensures a uniform distribution of heat Pre heating is not necessary Multiple cooking is possible as long as the cooking temperature of the different foods is the same 9 3 Grill cooking Ze FUNCTION SWITCH THERMOSTAT SWITCH AT MAXIMUM u Permits rapid browning of foods You are advised to place the pan in the highest guide For short term cooking of small quantities place the grid in the third guide from the bottom For long term cooking and grills put the grid in the lowest guide in accordance with the size of the pieces Make sure that the oven door is closed during cooking 25 Instructions for the user 9 4 Hot air grilling
13. d person 14 Instructions for the user ome 5 DESCRIPTION OF CONTROLS 5 1 Front control panel All the cooker controls and commands are on the front panel DESCRIPTION OF SYMBOLS OVEN THERMOSTAT Coe REAR RIGHT HAND COOKING OOO ZONE OVEN FUNCTIONS ego FRONT RIGHT HAND COOKING OO ZONE O99 FRONT LEFT HAND COOKING bed FISH COOKING ZONE OO ZONE O OO eo9 REAR LEFT HAND COOKING 699 FRONT CENTRAL COOKING ZONE OO ZONE oeo THERMOSTAT KNOB ONG Selection of cooking temperature is carried out by turning the knob clockwise to the required temperature between 50 and 250 C The tell tale light comes on to indicate that the oven is warming up When it goes out it means that the required temperature has been reached Regular flashing means that oven temperature is being constantly maintained at the programmed level Instructions for the user FUNCTION SWITCH KNOB Turn the knob to select from the following functions w E amp E z NO FUNCTION SET 4e LOWER HEATING ELEMENT VENTILATION mm UPPER AND LOWER LOWER HEATING ELEMENT HEATING ELEMENT VENTILATED HEATING ELEM ELEMENTO RISCALDANTE VENTILATED HEATING E3 SUPERIORE E INFERIORE ELEMENT VENTILATION VENTILAZIONE GRILL ELEMENT x DEFROSTING GRILL ELEMENT VENTILATION d COOKING HOB BURNER k COMMAND KNOB eco To light the flame press and turn the knob anticlockwise to the large flame symbol Adjust t
14. doors or outdoors and should preferably be close to the floor on the side opposite to the combustion gas discharge point If it is not possible to make the openings in the room where the cooker is installed the necessary air may be taken from an adjoining room proveded it is not a bedroom or a room with fire risk 2 4 Clearance above and around domestic cookers Extract from AS5601 THE TWO INSETS RELATE TO REQUIREMENT 3 BELOW Horizontal combustible surface below hob Horizontal combustible surface above trivet NOTE in this case any vertical combustible surface needs to be protected to conform with requirement 2 below Instructions for the installer REQUIREMENTS 1 Overhead clearances Measurement A Range hoods and exhaust fans shall be installed in accordance with the manufacturer s instructions However in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or for an overhead exhaust fan 750 mm Any other downward facing combustible surface less than 600 mm above the highest part of the hob shall be protected for the full width and depth of the cooking surface area in accordance with Clause 5 12 1 2 However in no case shall this clearance to any surface be less than 450 mm Side clearances Measurements B amp C Where B measured from the periphery of the nearest burner to any vertical combustible surface is less than 200 mm
15. e However a few simple operations have to be carried out periodically to prevent malfunctioning Burners the burners must be cleaned periodically to ensure correct combustion make sure that all the openings and flame ports are clean and free of obstacles and that the burners rest firmly on their supports Gas connection the gas connection must be checked periodically Flexible pipes if a flexible pipe is used it must be inspected periodically once a year for leakages if the surface of the pipe appears rigid and cracked disconnect immediately the cooker from the gas supply and replace the pipe with a new one Valves if the gas valves get stuck or hard to turn they need to be cleaned and re greased this operation must be carried out by an authorised person 12 PROBLEMS AND CAUSES Each of the following cases is caused by an abnormal operation of the appliance and should be dealt with by a authorised persons please contact your local dealer or Service Center in case you detect any of these malfunctioning PROBLEM CAUSE WHAT TO DO The flame is very long with Defect of comburent air or Clean the burner bright yellow tips incorrect injectors Call Service Center if the Black deposits on the Burner dirty or flame ports problem remains bottom of the pans obstructed The flame is very short and Excess of comburent air Call Service Center noisy The flame moves away from the burner ports The flame extinguishes Incorr
16. ect adjustment of Call Service Center when the burner knob is set the minimum heat input or to the low flame position excess of comburent air The valve knob is hard to Gas valve worn out or Call Service Center rotate needs lubrification
17. egular detergent 11 EXTRAORDINARY MAINTENANCE The oven may require extraordinary maintenance or replacement of parts subject to wear such as seals bulbs and so on The following instructions describe how to carry out these minor maintenance operations Before any intervention disconnect the power supply of the device 11 1 Replacement of light bulb Remove cover A by twisting anticlockwise replace bulb B with another similar bulb Refit the cover A Only use oven bulbs T 300 C 11 2 Removing the door Open the door completely and fit the pins supplied into the holes from the inside Close the door to an angle of about 45 lift it and remove it from its seat To replace fit the hinges into the grooves provided then lower the door until it comes to rest and extract the pins If the pins are lost two screwdrivers can also be used 31 32 Instructions for the user 11 3 Oven door seal To permit thorough cleaning of the oven the seal may be removed Before removing the seal take off the door as described above Once the door has been taken off lift the tabs at the corners as shown in the figure 11 4 Lubrication of gas taps With time it may happen that the gas taps get blocked and hard to turn Clean them inside and re grease them This operation must be done by a specialised technician ome Instructions for the user 11 5 Preventive maintenance This appliance does not need any special maintenanc
18. he flame by turning the knob to the area comprised between maximum and q minimum marks To turn off set the knob to either zero 15 Instructions for the user 5 2 Electronic Analogue Clock LIST OF FUNCTIONS MINUTE MINDER BUTTON D GH SIB AUTOMATIC SWITCH OFF TIMING BUTTON TIME SETTING AND RESET VALUE DECREASE BUTTON VALUE INCREASE BUTTON 5 2 1 Setting the time When the oven is used for the first time or after a power blackout the display flashes on and off at regular intervals Press the key for 1 2 seconds to stop the display flashing and start setting of the current time Press the value modification keys or to increase or decrease by one minute for each time a key is pressed Press one of the two value modification keys until the current time appears The clock will start from the time set 6 7 seconds after the last key is pressed At the end of each programmed cooking operation the clock gives 8 beeps repeated 3 4 times at intervals of about 1 and a half minutes The beeps can be stopped at any moment by pressing any key 16 Instructions for the user 5 2 2 Minute minder This function does not stop cooking but just triggers the beeps When the A key is pressed the display illuminates appearing as shown in figure 1 Press the T or keys within 6 7 seconds to set the minute minder Whenever a key is pressed 1 outside segment representing 1 cooking minute will ligh
19. nt parts are placed in the correct position When the installation is completed the installation connections of cooker will require to be leak tested the burner operating pressure and flame checked and adjusted Warranty service calls do not cover these adjustments To check the operating pressure of the appliance it is recommended at least 2 large size burners are used Ensure appliance is secured to wall when installation is completed N G The regulator supplied must be fitted to the BSP thread at the rear of the appliance An approved manual shut off valve must be installed The N G regulator must be checked and adjusted to 1 0kPa after installation L P G Can be connected to the inlet fitting directly The _ gt pressure must be checked to ensure it is operating at 2 75kPa Instructions for the installer 2 3 Room ventilation Caution This cooker may only be installed and operated in rooms permanently ventilated in accordance with current regulations For proper operation of a gas appliance it is essential for the air necessary for combustion of the gas to be able to flow naturally into the room Air must flow directly into the room through openings in its outside walls This these opening s must have a free passage cross section of at least 100 cm or 200 cm for appliances not equipped with gas safety device These openings must be constructed so that they cannot be obstructed in
20. r declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance Overall dimensions location of gas and electrical connection points all measures in mm 900 110 760 150 170 g O WU gt S06 Instructions for the installer 2 2 Gas connection This appliance is suitable for installation with Natural Gas or LPG Refer to page 12 for the relevant burner pressure and appropriate injector sizes When the appliance is to be connected to Natural Gas then the pressure regulator supplied must be fitted to the gas inlet A test point for checking the gas pressure is supplied either with the regulator or as a separate fitting in the case of LPG appliances Connection of the appliance to the gas supply must be in accordance with the requirements of AS5601 A BPS connector at the inlet is recommended and the gas supply line to the appliance must be of adequate length to allow sufficient withdrawal of appliance for service or disconnection and be a annealed copper pipe or b a hose assembly complying with requirements of AS 1869 class B or equivalent The cooker must be installed with provision to allow the gas to be turned off and disconnected for servicing and removal of the appliance as required from the gas supply Before the cooker is operated make certain all releva
21. s shown in the diagram after which the drawer can be removed from the appliance x aal 10 3 1 Self cleaning liners The main oven is equipped with continuous self cleaning enamelled liners These liners make the oven easier to clean and ensure its efficiency over time 10 3 2 Using the self cleaning liners Periodically to prevent food residues and unpleasant smells from accumulating inside the oven the appliance should be operated empty at temperatures of not less than 200 C for a time varying from 30 to 60 minutes in order to allow the self cleaning liners to oxidise the residues present when the oven has cooled these will then be removed with a damp sponge 10 3 3 Looking after the self cleaning liners The liners should not be cleaned with abrasive creams or ordinary detergents Use a damp sponge only so as not to damage the special characteristics of the enamel which coats the liners 10 3 4 Assembling the self cleaning liners 1 Remove all accessories from the oven 2 Remove the side grilles fig 1 3 Extract the side liners F and G fig 2 4 Remove the back panel A after undoing the threaded ring nut C fig 2 5 Reassemble the panels restoring them to their original position D Instructions for the user 10 4 Door glass The door glass should always be kept clean Use absorbent kitchen paper to clean In case of tough spots clean with a damp sponge using r
22. sh the cooker against the wall 4 The height of the screw hole from floor level must not exceed 800 mm C Instructions for the installer 3 ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work detach the ae appliance from the electrical socket The hob of the cooker is adjusted for use with either natural gas at a pressure of 1 0kPa A11X or LPG propane at a pressure of 2 75 kPa A11XLP In the case of functioning with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps To change the nozzles proceed as described below 3 1 Replacement of nozzles on the hob This operation requires no primary air regulation 1 Extract the grids and remove all the caps and flame spreader crowns 2 Unscrew the burner nozzles with a 7 mm socket wrench 3 Replace the nozzles according to the type of gas to be used and the description in paragraph 3 2 Burner and nozzle characteristics table Replace the burners in the correct position 11 Instructions for the installer 3 2 Burner and nozzle characteristics table Nominal gas Burner consumption LPG 2 75 kPa MJ h Turn down gas Injector consumption mm MJ h Auxiliary 3 9 1 8 0 54 Semi rapid 6 3 1 6 0 68 Rapid 10 8 2 7 0 88 Wok 13 5 5 8 1 00 Fish pan 6 8 2 9 0 72 Nominal gas Burner consumption NG 1 00 kPa MJ h Turn down gas Injector consumption mm MJ h Auxiliary
23. t up figure 2 shows 10 cooking minutes The countdown will start 6 7 seconds after the last key is pressed at the end of it you will hear the beeps During cooking with countdown the current time can be displayed by pressing the A key once press again to return to the minute minder display Atthe end of the countdown the oven has to be switched off by hand by turning the thermostat and the function selector to 0 18 Instructions for the user 5 2 3 Programming Cooking duration time the 2 button M can be used to set the cooking time Before setting it turn the thermostat to the cooking temperature of choice and the function selector knob to any setting To set the cooking time proceed as follows Press the M key for 1 2 seconds the pointer will move to position 12 Fig 1 Use the and keys to set the cooking time whenever the key is pressed 1 minute will be added to the cooking time and every 12 minutes a new inside segment will light up figure 2 shows a cooking time of 1 hour Once the required time has been set cooking will start about 6 seconds after the last time the or key is pressed Once cooking has started the display will show the current time represented by the constantly on segments and the minutes left until cooking finishes represented by the flashing segments every flashing segments indicates 12 minutes of cooking time left When the end
24. witch off the oven heating elements the beeps will start and the numbers on the dial will flash Toreset the entire program set keep the central key pressed for 1 or 2 seconds if cooking has already started the oven will have to be switched off by hand The image on the right shows an example of programming the current time is 7 06 and cooking is programmed to start at 8 o clock and finish at 9 At 8 o clock the inside segments between 8 and 9 will start to flash and the hour pointer will remain still Caution for the oven to start cooking after the programming procedure just described the thermostat and function selector must be properly set on the temperature and function required and T keys to set the 5 2 4 DEMO Function Models with analogue digital programmer feature a DEMO function which deactivates the heating elements while leaving the other functions unchanged To activate it simply press the i and keys for 3 4 seconds A confirmation beep will inform the user that the function is active To deactivate it simply repeat the same procedure 19 Instructions for the user 6 USE OF THE COOKING HOB 6 1 Lighting of the cooking hob burners lt Before lighting the hob burners check that the flame caps are in the lt correct position and that their burner caps are in place making sure thal LEN the holes A in the flame caps correspond to the spark plugs and thermocouples Grid B should
25. wn in the diagram 27 28 c Instructions for the user 10 CLEANING AND MAINTENANCE 10 1 Cleaning stainless steel Before performing any operations requiring access to powered parts switch off the power supply to the machine To keep stainless steel in good condition it should be cleaned regularly after use Let it cool first 10 1 1 Ordinary Daily Cleaning To clean and preserve the stainless steel surfaces always use only specific products that do not contain abrasives or chlorine based acids How to use pour the product on a damp cloth and wipe the surface rinse thoroughly and dry with a soft cloth or deerskin 10 1 2 Food stains or residues Do not use metallic sponges or sharp scrapers they will damage the surface Sg Use normal non abrasive products for steel and a wooden or plastic tool if necessary Rinse thoroughly and dry with a soft cloth or deerskin Do not allow residues of sugary foods such as jam to set inside the oven If left to set for too long they might damage the enamel lining of the oven 10 2 Cleaning of cooking hob components 10 2 1 Grids Extract the grids the central one first then the side ones Clean with warm water and non abrasive detergent taking care to remove incrustation Reassemble positioning the side ones first and then the central one Instructions for the user 10 2 2 Burner caps flame cap crowns and burners To facilitate cleaning caps flame cap
Download Pdf Manuals
Related Search