SkyLink TM-318 User's Manual
Contents
1. call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST Fax 800 286 1320 FE CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com http www skylinkhome com P N 101A396 US Patent D621795S Patent Pending 2010 SKYLINK GROUP 10 ACCESSORIES The SkylinkHome System consists of many other devices such as SkylinkPad Remotes Motion Sensor ON OFF Wall Switch Wall Dimmer Plug In Dimmer with or without Repeater Plug In ON OFF Control Outdoor Indoor Screw In Dimmer ON OFF Dimming Control ON OFF Control Smart Button Garage Door Control etc Please visit Skylink website at www skylinkhome com for more information2. G TRANSMITTERS Erasing the Snap On Remote from the ON OFF Wall Switch model WE 001 You may erase a transmitter from the receiver module but you cannot erase a specific device directly you must erase all the wireless devices then program the ones you want to keep Follow the instructions below to erase programmed transmitters Turn on the connected load with a programmed Snap On Remote the two blue LEDs on the switch will be off Remove the battery from the Snap On Remote Place the battery to the battery holder and insert the holder to the Snap On Remote as shown in section 2 Its red LED will be on steadily Press and hold the button on the Snap On Remote do not release this button until step 6 Press and hold the SET button on the switch for about 3 seconds until the upper blue LED flashes You may release the button on the Snap On Remote When the button is release you have successfully erased all the devices from the lighting receiver A Wh Sz NO Erasing TM remote from other receivers If you would like to erase TM remote from other receiver modules such as WR 001 MD 318 MR 318 PA 318 PR 318 PL 318 LS 318 etc please refer to the user s instructions of that receiver module Note The difference between programming a TC remote and programming a TM remote is as following 1 Press the PROG button on the back of a TC remote will activate programming 2 Remove battery then place
3. Snap On Remote Model TM 318 1 INTRODUCTION Thank you for your purchase of a SkylinkHome Snap On Remote Model TM 318 This transmitter allows you to wirelessly operate lighting home automation with the SkylinkHome receiver modules The Snap On Remote can work with all the SkylinkHome receiver modules even though it is specifically designed for mounting onto either Wireless Wall Dimmer Model WR 001 or On Off Wall Switch WE 001 All wireless signal communications within the SkylinkHome System are based on rolling code technology to ensure highest security is used You will find the following in this package Snap On Remote Lithium Battery CR 2032 User s Instructions Soe _ Snap On Remote TM 318 Lithium battery 2 PROGRAMMING TRANSMITTERS TO RECEIVER MODULE In order to remotely control lighting home automation connected to receiver a transmitter must be programmed to the receiver module To program a Snap On Remote to the receiver module follow the instructions below 1 Remove the battery from the Snap On Remote If the battery is not already installed skip to step 2 o Unlock i e Remove battery holder 2 Put the receiver module that you plan to program into programming mode Refer to the User s Instructions of that receiver module 3 Once the receiver module is in programming mode place the battery Positive side down to the battery holder and insert the holder to the Snap On Rem
4. ote as shown Its red LED will be on steadily LED Button Insert battery holder 4 Press the button on the remote its red LED will flash then off 5 Once the remote is programmed the receiver module will quit from Positive side with battery marking faces down programming mode and programmed transmitter is ready to be used now Note Once the receiver is in programming mode you have to finish the programming as soon as possible It will quit from programming mode after 15 sec even if you have not finished the programming You may have to start it over again 3 ON OFF OPERATION Pressing the button on the remote once will toggle the status of the load that is connected to the receiver module i e if the light is off pressing the button turns on the light and vice versa 4 BRIGHTNESS CONTROL OPERATION Besides turning on and off the light you may also control the brightness of the light if the receiver module and the light bulb is dimmable i e either incandescent light and dimmable compact fluorescent light connected to a dimmer To change the brightness first turn on the light Then press and hold the button on the Snap On Remote to change the brightness Hold the button until the desired brightness is reached then release the button Press and hold the button again to change the brightness again in the opposite way When the desired brightness is reached then release the button 5 ERASIN
5. the battery back into a TM transmitter again will activate the programming 6 BATTERY When the operating range is reduced or when the red LED does not flash during operation it is time to replace the battery Follow the same procedure as installing the battery in section 2 of this manual to replace the battery Note Dispose of old batteries promptly and properly 7 FCC The Remote Control is approved by the FCC and it complies with Part 15 of the FCC Rules Its operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user s authority to operate the equipment 8 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 9 CUSTOMER SERVICE If you would like to find out the up to date specifications know more about features and applications download documents i e user s instructions order Skylink products or if you have difficulty getting products to work please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com or 3
Download Pdf Manuals
Related Search