Sinclair Duro User's Manual
Contents
1. DUROO STRIPPER Operating Manual Read before use and keep safe Table of Contents 1 0 Technical Data Page 2 2 0 Safety Page 2 3 0 Safety instructions Page 2 4 0 Maintenance Page 3 5 0 Use Page 4 6 0 Information about various floorings Page 5 7 0 Troubleshooting Page 5 8 0 Spare Parts Page 6 9 0 Schematic Page 8 10 0 Blade Selection Page 10 800 624 2408 530 626 9386 Fax 530 626 5144 6686 Merchandise Way Diamond Springs Ca 95619 www sinegco com 1 0 Technical data technical description Power supply 120V AC Power consumption 2000W 18A with current limitor Number of strokes 8500 strokes min Sound pressure level 88 dB A Sound energy level 101 dB A Hand Arm Vibration 16 m s2 Weight 35 lbs Comes with Duro Stripper 2 rigid blades safety goggles and tool kit Case is optional 2 0 Safety The Sinclair Duro Stripper has Class 2 protective insulation It meets the following safety specifications DIN VDE 0740 CENELEC HD 400 IEC 745 VBG 7j National spec The machine has radio interference suppression to the standards 76 889 EWG 87 308 EWG EN 55014 3 0 Safety Instructions Disconnect the power supply before any maintenance is carried out Use only recommended blades and make sure the blade is sharp before starting Maintenance should be undertaken only by qualified personnel Use only genuine Sinclair parts Transport Always remove the blade before transporting the machine CAUTION Always wear ea2. e The warranty is void if the product is altered by the original consumer purchaser or if it is used in a manner not recommended by the manufacturer e The warranties do not cover consequential damages or transportation charges incurred with the replacement or repair of SINCLAIR EQUIPMENT COMPANY products e Not responsible for lost job or down time In no event shall SINCLAIR be liable for any indirect incidental or consequential damages from the sale or use of the product This disclaimer applies both during and after the term of this warranty SINCLAIR EQUIPMENT COMPANY disclaims liability for any implied warranties including implied warranties of merchantability and fitness for a specific purpose after the one year term of this warranty This warranty gives you specific legal rights and you may have other rights which vary from state to state Should you have any questions contact SINCLAIR EQUIPMENT COMPANY at 530 626 9386 To obtain warranty service deliver or send the complete tool prepaid to SINCLAIR EQUIPMENT COMPANY Be sure to include the following information Nature of failure Name and address of distributor where tool was purchased Application of tool when rendered defective and Proof of purchase To obtain individual repair parts contact SINCLAIR EQUIPMENT COMPANY with the following information e Tool model number e Item part number and e Description of part NOTES
3. D014815 28 4 Cyl screw M6x14 D014751 29 4 Safety washer M6 D014858 30 4 Cap Screw M6x22 D00912415B 31 2 Hexagon screw M14x35 D009167000N 32 2 Hexagon screw M8x20 D014775 33 2 Safety washer M14 D014863 34 1 Rubber sleeves D014932 35 1 Foot switch D015023 36 2 Counter sunk screw M5x70 Spax D014797 37 2 Safety washer M8 D014860 39 1 Baffle D015433 40 1 Gear block housing D015189 41 1 Needle bearing HK 1512 D015190 42 4 Cyl screw M5x45 D015191 43 1 Hexagon nut M10 D015192 44 1 Pinion D015193 45 1 Sealing bushing D015194 46 1 Ball bearing D014709 47 1 Sealing ring D015195 48 1 Cover D015196 49 1 Counter sink screw M5x16 D015197 51 1 Ball bearing 6001 2RS D014701 52 1 Bearing ring D015199 6 53 1 Air guide D015200 54 2 Cyl screw D019523 56 1 Current Limitor T015236 58 1 Motorcase with carbon D015203 59 2 Carbon brush holder D015206 60 2 Carbon brush D014997 61 2 Carbon brush holder cap D015207 62 1 Sealing plate Handle Motor Gasket D015208 63 1 PVC Stopper D016086 64 1 On Off switch D015209 65 2 Lens head screw M4x12 D015210 66 1 Cable clamp D015211 67 1 Handle D015212 68 2 Counter sunk screw M5x50 Spax D014796 69 1 Rubber sleeve Cable Sleeve D015214 70 1 Power Cord w Plug D5965VYC 71 1 Fan D015216 99 1 Duro Bravo Motor Complete D015022 100 1 Chasis
4. Complete D034245 102 1 Axle D017024 104 2 Pressure Springs D014896 105 2 Starlock Cap D014881 107 2 Transport Wheels T014954 108 2 Flat Washer M10 T014829 109 2 Locknut M10 BRO14817 Duro Wheel Assy Complete DO16151 Note When ordering the wheel assy you get items 100 107 Handle Assembly 110 1 Round Grip D015052 INOTE when ordering D 110 you get items 111 116 111 1 T Piece D015434 112 2 Star Grip Screw D014919 113 2 Nut D014825 114 2 Grip Covering D014923 115 2 Hexagon Screw 8x40 D014776 116 2 Clamping Lever D014877 117 1 Outer Tube D015232 118 1 Inner Tube D015226 120 2 T head bolt M 8x70 D014768 121 2 Wing Nut D014824 124 2 M14 Flat Washer D017741 Not Pictured Handle Assembly Hardware D011046400 Handle T Bar for Long Handle D015026 Handles For T Bar D009803000 Tool Kit D015025 Wrench 10mm 13mm T 7286A13 Hexagon screw M8x60 D009164900 DURO STRIPPER 24 03 2006 Motor DURO Stripper 14 09 2004 A QUI9SSSY IJPUBH TURBO EXTRO SUPER BRAVO DURO amp ECO STRIPPER SUGGESTED BLADE SELECTION BRAVO DURO ECO STRIPPER 10 4906 S Rigid Our standard blade for removal of vinyl carpet adhesive etc Bevel edge of blade should be up for concrete and down for wood sub surfaces Precutting of carpet and vinyl needed 10 4904 S Flexible Same as above yet for uneven concrete surfaces and some soft foam back carpet 10 4907T S Tile Blade For use on VAT and VCT tile Prevents tile fro
5. emely tight 7 0 Trouble shooting Trouble Eventual Cause Elimination Machine does not start Power supply disconnected Have machine repaired by a qualified electrician resp Blown fuse change parts Defective cable Defective plug Undue force necessary to Blade is blunt Change blades strip the flooring Excessive vibration Expendable parts are worn Return machine for service out and or repair 8 0 Spare Parts Duro Stripper Schematic Pieces Description Part 1 1 Striker Foot Casting D015221 3 1 Blade holder D015223 4 1 Bearing plate D015224 5 1 Drive shaft D015228 6 1 Grip frame D015227 7 1 Hand grip D014916 8 1 Locking flange Bearing Plate D015233 9 1 Counter Balance Weight D015225 10 1 Crown wheel Ring Gear D015234 11 4 Rubber bearings D014931 12 1 Fitting spring 5x 6 5 Woodruff Key D0 14905 13 1 Sealing ring O Ring D015218 14 1 Distance ring D015217 15 1 Locking clip 52 Snap Ring D014857 16 1 Ball bearings 6304 2RS C3 D014711 17 8 Cyl screw M6x20 D014752 18 4 Washer M6 D014859 19 4 Nylock Nut M6 D014815 20 4 Cyl screw M5x25 micro T014721 21 4 Safety washer M5 T014858 22 1 Ball bearing 3304 2RS C3 D014674 23 1 Washer M12 D014830 24 1 Countersink Screw M8x20 T014760 26 1 Shaft Seal for Gear Head D014847 27 8 Nylock Nut M6x1 0
6. g system 1 e the blade performs a circular movement This movement results in a lateral cutting This could make the stripper swing sideways if you want to remove stiff flooring or aggressive adhesive In this case using the device may be limited due to its system Before starting work the flooring needs to be cut into strips according to the blades width To begin cut one strip blade s width crosswise Then lift the flooring slightly in order to get the blade underneath it We recommend cutting the first strip at right angles to the main working direction By so doing access to the adjacent strips is made easier Cut the strips smaller if the floor covering is bonded very securely e g with an epoxy adhesive The blades are sharpened by the floor pavement Therefore the blade has to be changed only if itis twisted or becomes worn 6 0 Information about various floorings Main applications of the Duro Stripper are carpets with foam backing CV flooring PVC floorings and light carpets CV floorings PVC floorings and carpets without foam backing Cut strips according to the blade width Check from time to time if the blade is straight Carpets with foam backing Use sharp blades only Remove upper layer with carpet clamp Remove the foam backing with the stripper Remove foam across the width if you have an uneven sub floor Semi flexible tiles These tiles can be removed without pre cutting if they are not bonded extr
7. m jamming in between blade and blade holder A must for tile removal to protect blade holder 10 4909 8 Razor Blade Attachment An adapter to secure razor blades for removal of adhesives paints and thin films Inexpensive and an excellent choice for complete clean up after floor covering removal 10 4903 8 X 5 Rigid Ideal for hard to reach areas such as toe kicks under radiators etc Also used for clean up of small areas of parquet ceramic etc 10 4906D 8 X 2 5 Rigid Self Dicing For use on carpet rubber or vinyl A real time saver on pre cutting necessary since blade will cut strips with knife edged sides TURBO EXTRO SUPER STRIPPER Super Stripper uses 12 Blades Only 10 4801D 14 Self Dicing Blade For use on carpet rubber or vinyl A real time saver on pre cutting necessary since blade will cut strips with knife edged sides 10 4651T 12 Tile Blade For use on VAT and VCT tile Prevents tile from jamming in between blade and blade holder A must for tile removal to protect blade holder 10 4807 14 X 5 Ceramic Parquet Blade Ideal for removal for ceramic tile marble parquet and other wood floors Precutting needed for plank floors 10 4809 Special Ceramic Parquet Blade This 14 thick heavy duty blade is designed especially for the ceramic tile and hardwood parquet removal applications The 14 wide blade extends out nearly 4 and is designed at a specific angle to work more efficiently in c
8. nect the power supply and put on the blade protection before changing the blade Use work gloves for your own safety Loosen the screws of the blade mounting remove the blade and replace it Make sure that the sharp bevel of the blade always shows upwards and the blade is fitting in exactly the position of the old one 4 1 Genuine Spare Parts Spare parts and accessories are manufactured uniquely for the Duro Stripper It must be emphasized that parts obtained from unauthorized sources must not be used Sinclair Equipment Company cannot be held responsible for the performance of or any damage arising from the use of machines in which genuine spare parts have not been used This is particularly important with replacement blades 5 0 Use Starting Mount the long internal tube with 2 screws to the handle support Telescope the outer tube over 1t The length of the handle may be adjusted by sliding the outer tube Place the handle into the end of the tube and latch the locking For your safety the Duro Stripper comes with the blade not mounted Make sure that the power supply is disconnected before mounting the blade Place the sharp bevel of the blade face up when removing from concrete surfaces and face down when removing from wood or particle board The blade must sit close to its support and is fixed with screws from the bottom side Use The Duro Stripper removes bonded flexible floor covering in strips It uses an oscillatin
9. r and eye protectors CAUTION Using this machine without ear and eye protectors may jeopardize or harm your health It may harm especially your ears and increase the risk of an accident PLEASE READ DETAILED SAFETY INSTRUCTIONS ON COLORED SHEET BEFORE USING MACHINE 3 1 Introduction This operating manual should be used to receive the maximum benefit from your Duro Stripper Following these instructions will both extend the life of your machine and reduce repair costs Please make sure any user of the machine is familiar with these instructions before work begins 3 2 Danger while working with the machine The Duro Stripper is designed to the highest technical standards Incorrect use can be dangerous Use this machine only As instructed in this operating manual With the machine in perfect working order Disturbances that could impair safety have to be eliminated at once 3 3 Restriction of use The Duro Stripper is exclusively for removing bonded floor covering in dry environments It should not be used for any other purpose Sinclair Equipment Company cannot be held responsible for any damage or loss caused by incorrect use Correct use also includes To take care of all directions from the operating manual and The execution of maintenance and service 4 0 Maintenance The Duro Stripper is virtually maintenance free Check brushes periodically to prevent damage to armature Changing the blade Discon
10. utting and lifting of thick materials Best suited for the long run constant use in tile wood applications for extended life and performance 10 4802 14 Rigid 10 4652 12 Rigid The standard blade for carpet vinyl or adhesive removal pre cutting of the floor is needed 10 4804 6 Rigid 10 4803 S Rigid Use these blades for difficult removal like epoxy rubber floors sport surfaces etc Always position these blades to far left hand side of machine NOTE All jobs can vary in difficulty of removal Whatever blade you are using it may be necessary to take a smaller bite in removal so it is less stressful on the operator as well as the machine If you have any questions on blade selection or choice of machine please do not hesitate to call Sinclair Equipment Company or your nearest distributor STANDARD WARRANTY SINCLAIR EQUIPMENT COMPANY S tools are warranted to be free of defects in workmanship and materials for a period of one year from the date of original purchase Should any trouble develop during this one year period return the complete tool freight prepaid to SINCLAIR S authorized Service Center If inspection shows the trouble is caused by defective workmanship or materials SINCLAIR EQUIPMENT COMPANY will repair or at its option replace without charge e This warranty does not apply to malfunctions caused by damage unreasonable use faulty repairs made by others or failure to provide recommended maintenance
Download Pdf Manuals
Related Search