SIIG II-150 User's Manual
Contents
1. 4 Double click CD Drive D change D to match your CD ROM drive letter 5 Highlight Vista32 folder then click OK 6 Select Initio inicl1620 S ATA Adapter D Vista32 1620 inf then click Next 7 Follow on screen instructions to complete Windows Vista installation Existing Windows Vista Installation 1 Install the board and boot up Windows 2 At the Found New Hardware Wizard insert the driver CD select Locate and install driver software Recommended then click Continue 3 Click Next select Install this driver anyway then click Close 4 Remove the driver CD and restart Windows to complete the installation Windows Vista 64 bit New Windows Vista Installation 1 Install the board and follow Microsoft procedures to install Windows accordingly 2 At Where do you want to install Windows click Load Driver 3 Insert driver CD then click Browse 4 Double click CD Drive D change D to match your CD ROM drive letter 5 Highlight Vista64 folder then click OK 6 Select Initio inicl1620 S ATA Adapter D Vista64 1620 inf then click Next 7 Follow on screen instructions to complete Windows Vista installation Existing Windows Vista Installation 1 2 Install the board and boot up Windows At the Found New Hardware Wizard insert the driver CD select Locate and install driver software Recommended then click Continue Click Next select Install this driver anyway then click C2. make this floppy disk copy the contents of the Floppy folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow the Microsoft procedures to install Windows 2000 accordingly 2 Restart your system when prompted during Windows installation 3 At the Windows 2000 Setup screen press F6 to install the driver 4 Insert the driver diskette Press S then press Enter 5 Select INITIO INIC1620 S ATA Adapter For Windows 2000 and press Enter 6 Press Enter to continue and follow on screen instructions to complete the installation Existing Windows 2000 Installation 1 Install the board and boot up Windows 2000 2 At the Found New Hardware Wizard click Next 3 Select Search for a suitable driver for my device recommended and click Next 4 Insertthe driver CD check CD ROM drives uncheck the other boxes and click Next Click Next again to continue 5 Click Yes then click Finish 6 Restart Windows to complete the driver installation Windows XP Server 2003 New Windows XP Server 2003 Installation A new installation of Windows XP Server 2003 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the Floppy folder found on the driver CD onto a blank floppy disk then follow the directions below T Install the board and follow the Microsoft procedures to install Windows accordingly Restart your system w
3. G gt SATA IIl 150 PCI o Quick Installation Guide Introducing the SATA Il 150 PCI The SATA II 150 PCI is an ultra high speed dual channel Serial ATA Generation 2 controller for use in PCI enabled systems Features and Benefits Add up to two high speed SATA hard drives New Serial ATA cable easier to install amp provides better air circulation Supports two SATA channels and data transfer rate up to 1 5Gb s 150MB s Supports Native Command Queuing NCQ and SATA TCQ commands Onboard bus master engine relieves the system processor from book keeping and enhances performance Features independent 256 byte FIFOs per channel for host reads and writes Breaks the 137GB barrier Works with various brands of large capacity Serial ATA hard disks Supports SATA hard disk hot plugging Compliant with PCI 2 3 Compliant with Serial ATA 1 0 specifications and complement of SATA II optional features 04 0409D 1 System Requirements e Pentium or equivalent PC with an available PCI slot e Windows 2000 XP 32 64 bit Server 2003 amp 2008 32 64 bit Vista 32 64 bit Package Contents e SATA II 150 PCI e SATA data cable and power cable e Spare low profile bracket e Driver CD and this quick installation guide Layout HDD LED pins Front chassis LED connects vertically Internal connectors HDD ri Activity LED Figure 1 SATA II 150 PCI Board Layout Hardware Installation Note For low profile syst
4. aining an RMA number ship the product Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youare responsible for the cost of shipping Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer About SIIG Inc Founded in 1985 SNG Inc isa leading computer upgrade manufacturer ofI Oconnectivity products including PCI amp ISA serial and parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b networking sound cards and other accessories SIIG is the premier one stop source of upgrades SIIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs through major d
5. ble click Storage controllers then double click Initio INIC1620 S ATA Adapter A message This device is working properly is displayed the driver has been correctly installed BIOS Configuration The SATA II 150 PCI BIOS will appear everytime your system starts up If the BIOS doesn t show please try your controller in another PCI slot During this Post process the BIOS will show up and indicate the devices attached to it Technical Support and Warranty QUESTIONS SIIG s Online Supporthas answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analysts will promptly respond SIIG offers a lifetime manufacturer warranty with this product Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then RMA to submit a request to SIG RMA If the product is determined to be defective an RMA number will be issued Step 2 After obt
6. ems replace the currently mounted bracket with the included low profile bracket General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Turn OFF the power to your computer and any other connected peripheral devices 2 Unplug the power cord from the back of the computer 3 Remove your computer s cover 4 Remove the slot bracket from an available PCI slot 5 To install the card carefully align the card s bus connector with the selected PCI slot on the motherboard Push the board down firmly but gently until it is well seated 6 Replace the slot bracket s holding screw to secure the card 7 If needed connect the HDD LED pins to monitor HDD activity from the front panel of your chassis 8 Replace the computer cover and reconnect the power cord Driver Installation This section provides information on how to install the SATA II 150 PCI drivers for the following operating systems Windows 2000 New Windows 2000 Installation A new installation of Windows 2000 requires a floppy disk for the driver installation To
7. hen prompted by Windows installation At the Windows Setup screen press F6 to install the driver Insert the driver diskette Press S then press Enter 32 bit Select INITIO INIC1620S ATA Adapter For Windows XP 2003 and press Enter 64 bit Select INITIO INIC1620 S ATA Adapter For Windows XP 2003 AMD64 Press Enter to continue and follow on screen instructions to complete the installation Existing Windows XP Server 2003 Installation 1 2 Install the board and boot up Windows At the Found New Hardware Wizard XP w SP1 or earlier Server 2003 continue to step 3 XP w SP2 or later Server 2003 w SP1 or later select No not at this time then click Next 3 Insert the driver CD select Install the software automatically Recommended then click Next Next 4 Click Continue Anyway then click Finish 5 Restart Windows to complete the driver installation To Verify Windows 2000 XP 2003 Installation 1 Right click My Computer and click Manage 2 Select Device Manager 3 Double click SCSI and RAID Controllers then double click Initio inic1620 S ATA Adapter 4 Amessage This device is working properly is displayed the driver has been correctly installed Windows Vista 32 bit New Windows Vista Installation 1 Install the board and follow Microsoft procedures to install Windows accordingly 2 At Where do you want to install Windows click Load Driver 3 Insert driver CD then click Browse
8. indows to complete the installation Windows Server 2008 64 bit New Windows 2008 Installation 1 10 Install the board and follow Microsoft procedures to install Windows accordingly At Where do you want to install Windows click Load Driver Insert driver CD then click Browse Double click CD Drive D change D to match your CD ROM drive letter Highlight Vista64 folder then click OK Select Initio inic1620 S ATA Adapter D Vista64 1620 inf x64 click Next then click OK Repeat steps 2 4 then continue to step 8 Hightlight Vista32 folder then click OK Select Initio inic1620 S ATA Adapter D Vista32 1620 inf click Next then click OK Follow on screen instructions to complete Windows Vista installation Existing Windows 2008 Installation 1 2 Install the board and boot up Windows At the Found New Hardware Wizard insert the driver CD select Locate and install driver software Recommended then click Don t search online Click I don t have the disc Show me other options Click Browse my computer for driver software Advanced Type in D Vista64 change D to match your CD ROM drive letter then click Next Click Install this driver software anyway then click Close Remove the driver CD and restart Windows to complete the installation To Verify Windows Server 2008 Installation 1 Right click Computer click Manage double click Diagnostics click Device Manager Dou
9. istributors system integrators and VARs in the Americas and the UK and throughe commerce sites PRODUCT NAME SATA II 150 PCI FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Ph 510 657 8688 SATA II 150 PClis a trademark of SIG Inc SIIG and the SHG logo are registered trademarks of SIG Inc Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Pentiumisa registered trademark of Intel Corporation Other names used in this publication are for identification only and may be trademarks of their respective companies February 2009 Copyright 2009 by SIIG Inc All rights reserved
10. lose 4 Remove the driver CD and restart Windows to complete the installation To Verify Windows Vista Installation 1 2 3 4 Rightclick Computer click Manage click Continue Select Device Manager Double click SCSI and RAID Controllers then double click Initio inic1620 S ATA Adapter A message This device is working properly is displayed the driver has been correctly installed Windows Server 2008 32 bit New Windows 2008 Installation T Install the board and follow Microsoft procedures to install Windows accordingly At Where do you want to install Windows click Load Driver Insert driver CD then click Browse Double click CD Drive D change D to match your CD ROM drive letter Highlight Vista32 folder then click OK Select Initio inic1620 S ATA Adapter D Vista32 1620 inf then click Next Follow on screen instructions to complete Windows Vista installation Existing Windows 2008 Installation 1 2 Install the board and boot up Windows At the Found New Hardware Wizard insert the driver CD select Locate and install driver software Recommended then click Don t search online Click I don t have the disc Show me other options Click Browse my computer for driver software Advanced Type in D Vista32 change D to match your CD ROM drive letter then click Next Click Install this driver software anyway then click Close Remove the driver CD and restart W
Download Pdf Manuals
Related Search