SIIG 04-0600B User's Manual
Contents
1. Satellite Speaker Mounts 1 Pair Quick Installation Guide Introduction The Satellite Speaker Mounts 1 Pair are fully adjustable Tilt Swivel amp Pivot speaker wall or ceiling mounts Key Features and Benefits Universal design fits most speaker brands amp designs Ceiling or wall mountable amp compatible with 1 2 or 4 hole and key hole speaker mounting with included adapters Allows customizable tilt swivel amp pivot angle adjustments for optimal speaker positioning Holds speakers weighing up to 8 lbs Serial Number Sticker For future product return or exchange this serial number is required Please keep it for your reference Z 04 0600B 1 Package Contents 2 Speaker mounts 2 1 hole adapters 2 2 4 hole adapters 2 2 14 ceiling mount extensions Mounting hardware Quickinstallation guide Mounting Hardware ardal O Olaal M6x20mm Machine Screw M5 x 20mm Machine Screw 8 32 x 5 8 Machine Screw 1 4 20 x 1 2 Machine Screw M5 x 1 8 Plastic Screw 8 32 Hex Key Hole Nut 8 x 3 4 Self Tapping Screw 12 x 3 4 Self Tapping Screw 12 x 1 3 4 Self Tapping Screw 12 14 Alligator Anchor M4 x 8mm Flat Head Machine Screw Installation Please read the instructions prior to installation This speaker mount is designed solely for the mounting of small speakers weighing less than 8lbs We are not responsible for damage that may occur if speakers weighing more th2. 8 machine screws in combination with the 8 32 Hex Key Hole Nut Loosely pre assemble the mounting post with the 8 32 x5 8 machine screw and hex key hole nut see Figure 4 below Keyhole Mounting Post M5 x 1 8 Plastic Washer l N mmm 8 32 x 5 8 Machine Screw Back Speaker 8 32 Hex Key Hole Nut Figure 4 Engage the hex key hole nut into the key hole slot Put tension on the assembly by gently pulling back on the speaker mount post while tightening the 8 32 x 5 8 machine screw see Figure 4 on page 5 The hex key hole nut will engage on the housing in the key hole slot If the post does not tighten securely against the housing it will be necessarry to use the M5 x 1 8 plastic washer as a spacer under the head of the 8 32 x 5 8 machine screw see Figure 4 on page 5 2 4 Hole Mounting 1 Find the best mounting configuration that matches your speaker enclosure Four hole mount patterns can be accomodated by positioning the speaker plate diagonally see Figure 5 on the next page Using the 1 4 20 x 1 2 machine screws install the speaker plate and secure the speaker enclosure see Figure 5 on the next page el Back 1 4 20 x 1 2 zn Machine Screw 4 Hole Orientation 2 Hole Orientation Figure 5 Self Tapped Mounting 1 Locate the optimum location for the mounting plate and use it as template to mark the drilling locations Donot drill or screw into the speaker where you could possibly dama
3. MA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer 15 About SIIG Inc Founded in 1985 SIG Inc is a leading manufacturer of IT connectivity solutions including Serial ATA and Ultra ATA Controllers FireWire USB and legacy I O adapters that bridge the connection between Desktop Notebook systems and external peripherals SIIG continues to grow by adding A V and Digital Signage connectivity solutions to our extensive portfolio SIIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs inthe Americas and the UK and through e commerce sites PRODUCT NAME Satellite Speaker Mounts 1 Pair FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference
4. an 8lbs are used The user will have to determine which type of configuration will work best with the included mounting hardware If the included hardware does not fit with the application the appropriate hardware will have to be purchased Single Hole Mounting 1 Most satellite speakers will require the use of the M5 x 20mm machine screw used in combination with M5x1 8 plastic washer The plastic washer is used as a spacer between the threaded insert and the post see Figure 1 below Itis critical the plastic washer is used correctly M5 x 20mm Machine Screw Back Speaker Mounting Post M5 x 1 8 Plastic Washer Figure 1 Once the proper configuration is determined secure the post to the speaker Some speakers use the smaller M4 x 8 screw which is inserted into the off center on the mounting post see Figure 2 below M4 x 8mm Flat Head Machine Screw Back Speaker Figure 2 Check the size of the hole make sure you have the 8 32x5 8 machinescrew the 1 4 20x 1 2 machine screw the M6 x 20mm or the M5 x 20mm fits inside see Figure 3 below NI o Back Speaker a d d Figure 3 When the correct size is determined place the screw through the speaker post and attach to the rear of the speaker enclosure If the screw does not tighten properly use the M5 x 1 8 plastic washer to tighten itup Key Hole Mounting 1 If your speaker has a factory key hole design you will use the 8 32 x 5
5. e drywall using a 5 16 drill bit Once the holes are drilled insert the alligator anchor into the holes Make sure the anchor is flush with the wall and or ceiling surface see Figure 8 on the next page 4 Withtheanchorsinplace mountthe wallplatesusing the 12 x3 4 self tapping screws see Figure 8 below 12 x 3 4 Self Tapping Screw Pre Drill 5 16 Holes Insert Alligator Insert screw through wall plate Anchor de and into the alligator anchor be Figure 8 Concrete Surface 1 Using the wall plate as a template mark hole positions on the mounting surface For in wall applications position the mounting holes in a vertical pattern see Figure 9 on the next page 2 Drill holes in the solid concrete or hollow block using a5 16 masonry bit Once the holes are drilled insert the 12 14 alligator anchors into the holes and make sure the anchor is flush with the surface of the wall see Figure 9 on the next page Insert Alligator S Anchor 12 x 3 4 Self Tapping Screw Insert screw through wall plate and into the alligator anchor Using the hammer to tap anchor into place Figure 9 er With the wall anchor in place mount the wall plate using the 12 x 3 4 self tapping screws see Figure 9 above Extension Mounting This is for ceiling and or shelf applications Do not use extension in the wall application 1 Install a 2 1 4 ceiling mount extension to the wall plate 2 Secure the set
6. ge the internal components 2 Drill the pilot hole s using a1 8 drill bit The holes s should not be drilled more than 1 2 depth see Figure 6 on the next page 12 x 3 4 Self Tapping Screw Back Speaker Figure 6 Mounting to the Wall or Ceiling The mounting hardware for the three different surface applications is supplied You will need to determine what style hardware will work best with your mounting surface Always use caution when drilling into a wall or ceiling Make sure to avoid all electrical and water lines Wood Surface 1 Using a stud finder locate the wood stud or framing member Always mount the speakers in the center of astud 2 Usingthe wall plate as a template mark hole positions onmounting surface Forin wall applications position the mounting holes in a vertical pattern see Figure 7 on the next page if SE SE Ki E LL K H e e 12 x 13 4 Self Tapping Screw Figure 7 Drill holes through the drywall and into the wood stud usinga 1 8 drill bit These holes should be drilled 1 1 2 deep see Figure 7 above After the holes are drilled mount the wall plate using the self tapping screws Drywall Surfaces 1 Locate the best mounting location in the ceiling or wall Using the wall plate as a template mark the hole positions on the mounting surface For in wall applications position the mounting holes ina vertical pattern see Figure 8 on the next page Drill holes in th
7. or product having similar features and functionality the product if defective in materials or workmanship This warranty gives you specific legal rights and you may also have other rights which vary from state to state Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow the steps below to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then REQUEST A PRODUCT REPLACEMENT to submit a request to SIG RMA or fax a request to 510 657 5962 Your RMA request will be processed if the product is determined to be defective an RMA number will be issued Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e You are responsible for the cost of shipping to SIG Ship the product to the following address SIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA R
8. screw to hold the extension in place with the weight of the speaker attached Ey Tighten the allen screw using the provided allen wrench Figure 10 11 Low Profile Mounting This is for wall and ceiling application E Install the low profile portion of the speaker mount to the wall plate or 2 1 4 extension 2 Secure the setscrew to hold the extension in place with the weight of the speaker attached Tf Tighten the allen screw using the provided allen wrench Figure 11 Speaker Mounting 1 Install the speaker with the speaker post or 2 hole plate attached 2 Secure the screw to hold the extension in place with the weight of the speaker attached Post Style Speaker 2 Hole Speaker Figure 12 Blank Page Blank Page Technical Supportand Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www stig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analyst will promptly respond SIIG offers a 5 year manufacturer warranty with this product This warranty covers the original purchaser and guarantees the product to be free of any defects in materials or workmanship for five 5 years from the date of purchase of the product SIIG will at our discretion repair or replace with an identical product
9. that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Phone 510 657 8688 Satellite Speaker Mounts 1 Pair is a trademark of SIIG Inc SIIG and the SIIG logo are registered trademarks of SIIG Inc All othernames used in this publication are foridentification only and may be trademarks of their respective owners November 2011 Copyright O 2011 by SIIG Inc All rights reserved
Download Pdf Manuals
Related Search