Siemens TPSA9040 User's Manual
Contents
1. or fitness for a purpose are not excluded but are limited to the duration of the Warranty Period Page 52. TPSA9040 Residential Transient Voltage Surge Suppressor User s Manual SIEMENS Introduction Thank you for choosing the Siemens TPSA9040 Residential Transient Voltage Surge Suppressor Save this manual It includes instructions for obtaining warranty service and for returning a defective device Please read and understand all information in this manual prior to installation The procedures contained herein are not intended to supersede local or national electrical codes Check all applicable electrical codes to ensure compliance In all instances local and national electrical code requirements are to be followed This manual provides instructions for installing the TPSA9040 Transient Voltage Surge Suppressor TVSS The TPSA9040 TVSS Figure 1 can be mounted three ways The preferred way is to mount the TVSS directly to the outside of the electrical panel equipment using the chase nipple on the body of the TVSS It can also be installed against a panel wall using installer supplied hardware or it can be installed using an optional Flush Mount Kit The latter two methods require use of additional conduit and hardware not provided The TPSA9040 provides a broad range of protection from damaging transient voltage surges and spikes Proper installation is imperative to maximize the effectiveness and overall performance of this device This device must be installed by a licensed electrician The electrician should follow the step
3. ance vandalism Acts of God war terrorism misuse or abuse The Standard and Additional Limited Warranties above do not cover service charges installation removal or re installation costs setup costs diagnostic charges period checkups routine maintenance loss of use of the product and or shipping or transportation charges or fees TO THE FULLEST EXTENT ALLOWED BY APPLICABLE LAW SIEMENS HEREBY DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PUR POSE NEITHER SELLER NOR ITS SUPPLIERS SHALL BE LIABLE IN CONTRACT WARRANTY FAILURE OF A REMEDY TO ACHIEVE ITS INTENDED OR ESSENTIAL PURPOSES TORT INCLUDING NEGLIGENCE STRICT LIABILITY INDEMNITY OR ANY OTHER LEGAL THEORY FOR INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES Buyer is limited to the remedies specified herein and shall have no others for a nonconformity in the goods Buyer agrees that these remedies provide Buyer with a minimum adequate remedy and are exclusive remedies whether based on contract warranty tort including negligence strict liability indemnity or any other legal theory and whether arising out of warranties representations instructions installations or non conformities from any cause With respect to products purchased by consumers in the United States for personal use implied warranties including but not limited to the warranty of merchantabil ity
4. e TPS TECHNICAL SUPPORT AND CUSTOMER SERVICE Wire Size Wire Size 12 AWG See Circuit Breaker for torque rating United States and Canada 1 888 333 3545 Circuit Breaker and 20 Amp 2 Pole 120 240 r Installation Torque Torque to 18 inch lbs This manual and information about the entire Siemens product line are available on the Internet at Per IEEE STD 142 1991 For sensitive www sea siemens com electronics computer systems the recommended ground impedance is 24 A Return Material Authorization number RMA must be ohms or less given by the Company prior to the return of any product Returned products must be sent to the factory with the transportation charges prepaid System Grounding AC Surge Protection Prior to calling Siemens for technical support please have Thermal Fusing the following information available Catastrophic Surge Circuit Single Pulse Energy Dissipation 1080 Joules Model Number of unit Spike Capacity 40 000A Manufacture Date Line Voltage 120 240 1 Phase 50 60 Hz Installation Date Bete Vola iy Return Shipment Address eae 3 TPS Technical Support ee ee ep neon 14550 58th Street North Clearwater FL 33760 Attn RMA Page 4 Siemens Energy amp Automation Inc Seller TPSA9040 Transient Voltage Surge Suppressor Limited Warranty a Warranty Period The Warranty Period shall be sixty 60 months from the date of initial installation but not more than sixt
5. e to follow all electrical safety precautions All power sources to this unit should be locked off before servicing This will prevent the risk of receiving an electrical shock CAUTION HAZARDOUS VOLTAGE BONDING BETWEEN CONDUIT CONNECTIONS IS NOT AUTOMATIC AND MUST BE PROVIDED AS PART OF THE INSTALLATION DO NOT CONDUCT DIELECTRIC AND OR HIGH POTENTIAL TESTING ON THIS UNIT THIS TESTING WILL CAUSE INTERNAL DAMAGE Page 2 Installation Installing the TPSA9040 TVSS To install the TVSS to the electrical panel equipment proceed as follows 1 2 3 Ensure power to the electrical panel equipment has been disconnected Remove the screws securing the outer panel equipment cover to the electrical panel equipment see Figure 1 Select the location where the TVSS will be mounted should be based on the internal configuration of the electrical panel equipment and the physical surround ings outside the equipment Note that the TVSS s lead length must be minimized to achieve maximum performance Once the location has been determined drill or punch a 7 8 diameter hole in the top bottom or side surface of the electrical panel equipment The ideal mounting location will also allow the TVSS to be secured to the wall or panel in addition to using the chase nipple Screw one of the conduit nuts on to the chase nipple until it bottoms out Note bonding of the conduit connections to the electrical panel equipment is no
6. ge is caused by the failure of a properly installed TVSS to protect such connected appliances against electrical power surges caused by lightning strikes or other electrical disturbances This warranty shall apply only if Siemens receives written notice of such damages during the Warranty Period For purposes of this Additional Limited Warranty Major Household Appliances shall mean exclusively refrigerators freezers air conditioners stoves ovens clothes washers clothes dryers ceiling fans and dishwashers Major Household Appliances shall not include other electronic devices including but not limited to microwave ovens audio and stereo components satellite dish equipment video equipment televisions computers or fax machines Siemens total aggregate liability under this Additional Limited Warranty shall be the lesser of 20 000 or the deductible amount of any applicable insurance policy covering such connected Major Household Appliance This Additional Limited Warranty shall be secondary to any existing manufacturer warranty any service contract or any applicable homeowners or other insurance policy in effect at the time of loss d Warranty Exclusions and Limitations The Standard and Additional Limited Warranties above only apply to non commercial residential use of the TVSS and exclude damages or loss arising from any of the following unauthorized product modification or alteration improper storage installation operation or mainten
7. lly inspect each item in the package for signs of damage If damage is found please contact Siemens Technical Support 1 888 333 3545 For more information about this product or other Siemens products visit Www sea siemens com Safety Information This section provides pertinent safety information that must be considered before installing the TVSS e Do not install this device during a lightning storm e This device is rated NEMA 4X Suitable for indoor and outdoor applications The conduit nipple must be sealed against the panel using watertight fittings not supplied to ensure a watertight connection e Do not install the surge protector in an excessively hot or moist location e Other safety considerations are listed on the following page Page 1 Wa Hazardous voltage Will cause death or serious injury Disconnect power before working on this equipment Verify all power circuits are de energized before making any connections The voltage rating of the device and system must always be verified before energizing the TVSS All electrical connections should be performed by a qualified licensed electrician All wiring must comply with the National Electrical Code NEC and applicable local codes Maintenance of this Transient Voltage Surge Suppressor should be performed by qualified electrical personnel only During normal operation hazardous voltages are present inside the unit When servicing this unit be sur
8. owever in the event of a power anomaly or a malfunction the operational status may change and may require action The table below outlines the operating conditions of the TPSA9040 and any correction action if required Light Light Alarm Audible A 1 2 Red Corrective Action Reset Breaker Out Qu Out If Breaker Trips Replace Unit e e em ou e Replace Unit G Out Blinks Sounds Replace Unit i Check Neutral to Ground G G Blinks Sounds Connection before Replacing Unit This device features internal circuitry that will disconnect the surge protective component at the end of its useful life Power will maintain to the load however the load is now unprotected Follow the manufacturer s instructions for replacing the device Page 3 Specifications Model Voltage Rating and Service Type Agency Approvals amp Warranty UL 1449 Rating 400V Meets ANSI C62 41 1 Yes Specification Requirements Temperature Operating 40 C 40 F to 60 C 140 F Free replacement during Lightning Protection TemperatureStorage 55 C 65 F to 65 C 149 F g g warranty period Service Clearance 36 inches 94 1 cm in front of the unit Appliance Warranty 3 Years Installation Type Chase Nipple Wire Length vs 1 foot 31 7 cm of wire 1 nanosecond i Response Time and 175 volts per foot 6kV 3kA 8 20 micro Customer Service Let Through Voltage seconds are added to the clamp voltag
9. quipment cover Apply power to the panel equipment LEDs will illumi nate on the TVSS If any connected phase LED on the TVSS does not illuminate remove power check all connections and test again If any connected phase LED still does not illuminate contact Siemens Technical Support at 1 888 333 3545 11 The TPSA9040 is equipped with an audible alarm which will sound in the event of an alarm condition This indicates a problem with the TVSS which requires further evaluation There is no test or silence switch De energizing the TVSS will silence the alarm Figure 1 Typical TPSA9040 TVSS Installation Mounting Screws 4 places not supplied TPSA9040 TVSS Integral Chase Nipple nut installed Chase Nipple Nut Wiring to Breaker Black Black Breaker Outer Breaker Panel Cover Screws 6 places typical Wiring to Neutral or Ground Bus Ground Green Neutral White if used 000090000 Electrical Panel Figure 2 Typical Parallel Connections To Protected Loads en Phases Neutral if used Ground p 000 alk Ground B N Interconnecting Wiring e Minimize Length e Avoid Sharp Bends NOTE Safety Ground required for ALL units Dimensions and Weight The TPSA9040 weight is 4 lbs 4 7133 _ Operation The Siemens Residential surge suppressor normally requires no remedial action H
10. s outlined in this manual to insure proper installation Note Siemens products are extensively tested to industry standards as set by IEEE C62 41 and C62 45 for Categories A B and C The TPSA9040 is listed to the most recent edition of UL 1449 This product is suitable for installation on electrical distribution equipment capable of delivering not more than 25 000 rms symmetrical amperes During installation into an electrical system the TPSA9040 must NOT be energized until the electrical system is installed inspected and tested All conductors must be connected and functional including neutral if required Failure to follow the guidelines in this manual can lead to abnormally high voltage being applied to the TVSS This may cause the TPSA9040 unit to become inoperative The warranty does not cover an incorrectly installed device Do not high potential test the electrical system with the TVSS connected Failure to disconnect the TVSS during elevated voltage testing will result in damage to the suppression components and or other electronic compo nents see Safety Information Parts List and Inspection Items included in the package consist of the following e 1 TPSA9040 Transient Voltage Surge Suppressor e 1 User s Manual this document If the Flush Mount Kit Part KITFMC was ordered additional parts are supplied as follows 1 Flush Mount Panel 1 Flush Mount Installation Instructions e 4 Pan head Screws Carefu
11. t automatic and must be provided as part of the installa tion remove paint from the electrical panel equipment surface prior to installing the TVSS and chase nipple Push the leads from the TVSS through the 7 8 diameter hole toward the inside of the electrical panel equip ment Push the leading part of the chase nipple through the hole and secure the TVSS using a second conduit nut sandwiching the metal wall of the electrical panel equipment between the two conduit nuts If possible to provide extra rigidity in the installation attach the TVSS to the wall or electrical panel equip ment using installer supplied hardware Trim the leads from the TVSS as short as possible but still allowing the following connections to be made see Figure 2 e Black wires two in number go to the nearest free 20 amp circuit breaker The phase of each lead is marked with a white band and letter designator L1 amp L2 Connect the TVSS leads to the appropriate phases It is not critical which black wire goes to the positions on the circuit breaker however connect to L1 and L2 if known e Connect the white Neutral wire to the neutral bar using a set screw e Connect the green Ground wire to the electrical panel equipment ground Note Conducting dielectric and or high potential testing will cause internal damage to the TVSS unit DO NOT perform dielectric or high potential tests with the phase or neutral TVSS wires connected Install the panel e
12. y six 66 months from the date of purchase by Buyer b Standard Limited Warranty Siemens warrants to the original Buyer that on the date of shipment the Transient Voltage Surge Suppressor TVSS is of the kind and quality described herein and is free of non conformities in workmanship and material when properly used under normal care in a residential installation that complies with all National Electrical Code and or other applicable requirements Buyer s exclusive remedy for a nonconformity in the Circuit TVSS shall be the repair or the replacement at Siemens option of the TVSS Siemens obligation to repair or replace shall be in effect only if Buyer has sent written notice of any non conformity within the Warranty Period Repaired and replacement parts shall be warranted for the remainder of the original period of notification set forth above At its expense Buyer shall remove and ship to Siemens any such nonconforming items and shall reinstall the repaired or replaced parts Buyer shall grant Siemens or its agents access to the goods at all reasonable times in order for Siemens to determine any nonconformity in the goods Siemens shall have the right of disposal of items replaced by it c Additional Limited Warranty for Connected Major Household Appliances Siemens will reimburse the original Buyer for direct repair replacement costs actually incurred for damages to Major Household Appliances but only to the extent that such dama
Download Pdf Manuals
Related Search