Shure Headphones WH30 User's Manual
Contents
1. 90WP1371 SPECIFICATIONS WH30TQG WH30XLR Type Condenser electret bias Condenser electret bias with integrated preamplifier Frequency Response 40 to 20 000 Hz See Figure 6 Polar Pattern Unidirectional cardioid see Figure 7 Output Impedance at 1kHz 2400 Rated 150 actual Tolerates loads as low 150 Q with reduced clipping level Output Level 55 5 dB 1 7 mV 54 5 dB 1 9 mV at 1 kHz 0 dB 1 V Pascal Signal to noise ratio ref 63 0 dB at 94 dB SPL IEC 651 A weighted noise Output Clipping Level at 1000 22 dBV 0 08 V 2 5KO Load 8 dBV 0 4V Hz 1 KO Load 8 dBV 0 4V Maximum SPL 130 dB 2 5KQ Load 142 dB 1 KO Load 142 dB Dynamic Range SPL to 99 dB 111 dB A weighted noise level Output Noise equivalent SPL 31 dB typical A weighted Recommended Operating 5 VDC 11 52 VDC Phantom power Voltage pin 2 to pins 3 and 4 Polarity Positive sound pressure on Positive sound pressure on the diaphragm produces positive diaphragm produces positive voltage on pins 3 and 4 relative to voltage on pin 2 relative to pin 3 of 1 ground on the mini TA4F preamplifier output connector connector Environmental Conditions Operating Temperature 7 to 49 C 20 to 120 F Storage Temperature 29 to 74 C 20 to 165 F Humidity O to 95 operating or storage 1 2 m 4 ft two conductor shielded Headset 65 g 2 3 oz Headset2. m SHURE Models WH30TQG and WH30XLR User Guide MODEL WH30 CONDENSER HEADSET MICROPHONE MICROPHONE DE CASQUE ELECTROSTATIQUE SHURE MODELE WH30 KONDENSATOR KOPFMIKROFON MODELL SHURE WH30 MICROFONO DE CONDENSADOR DE CABEZA MODELO WH30 SHURE MICROFONO A CONDENSATORE CON SUPPORTO A CUFFIA SHURE WH30XLR ONLY MODELLO WH30 2006 Shure Incorporated C Printed U S A 27G3121 Rev 9 ase INTRODUCTION The Shure Model WH30 is a light yet rugged headset microphone Designed for vocalists and instrument playing vocalists the WH30 utilizes a high quality electret condenser car tridge suitable for all applications where mobility comfort low microphone visibility and high sound quality are required Because of its cardioid unidirectional pickup pattern the WH30 provides isolation from extraneous sound sources and high gain before feedback The wireframe and gooseneck adjust to any head size and shape An integrated elastic headband comfortably pads and secures the headset The WH30 is supplied with two snap on windscreens clothing clip storage bag and cable management device FEATURES Smooth natural frequency response comparable to professional condenser hand held microphones Lightweight wireframe and headband adjust for a secure comfortable fit Extra strong small diameter microphone cable resists breakage Moisture proof cartridge housing Sturdy gooseneck boom holds
3. and cord 60 g 2 1 oz Preamplifier 99 g 3 5 o 20 10 2 0 t E Bes ease 10 E Secure 1 cm 0 4 in c Marius a QJ Cm 24 in 20 50 100 200 500 1 000 2 000 5 000 10 000 20 000 Hz TYPICAL WH30 FREQUENCY RESPONSE FIGURE 6 TYPICAL WH30 POLAR PATTERNS FIGURE 7 WIRING DIAGRAMS _ CARTRIDGE MIC FET ELEMENT MODEL WH30TQG TA4F CONNECTOR RED to drain DG bias B RG FILTER BLACK te source audo Em I SHIELD TY BEJ MODEL WH30XLR WH30 WIRING DIAGRAMS FIGURE 8 10 XLA CONNECTOR 47 TRADE MARK NOTICES The stylized Shure logo and the Word Shure are registered trademark of Shure Incorporated in the United States Teflon is a registered trademark of E I duPont de Nemours and Company the United States i mdi SHURE Incorporated http www shure com United States Canada Latin America Caribbean 5800 W Touhy Avenue Niles IL 60714 4608 U S A Phone 847 600 2000 U S Fax 847 600 1212 Intl Fax 847 600 6446 Europe Middle East Africa Shure Europe GmbH Phone 49 7131 72140 Fax 49 7131 721414 Asia Pacific Shure Asia Limited Phone 852 2893 4290 Fax 852 2893 4055 48
4. D SYSTEM Wireless Applications WH30TQG 1 Connect the mini TA4F connector from the WH30 to a wireless microphone trans mitter such as the Shure T1 bodypack transmitter 2 See the user guide for your wireless transmitter and receiver system for adjusting gain and other parameters Wired Applications WH30XLR Connect the output of the RPM420 preamplifier to an input channel of a mixing or record ing console Most consoles will provide phantom power to the RMP420 preamplifier If phantom power is unavailable use a separate phantom power supply such as the Shure PS1A WASHING THE ELASTIC HEADBAND When necessary remove and wash the elastic headband according to these steps Remove the microphone cable retainer from the wireframe Slide the elastic headband off the wireframe Wash the headband in mild soapy water and rinse it in clean water Allow the headband to air dry thoroughly Slide the headband around the wireframe to its original position Reattach the cable with the plastic retainer WASHING THE FOAM WINDSCREEN The foam windscreen protects the WH30 s microphone element from dirt and moisture When necessary it can be removed and cleaned in a mild soapy water solution AND v Important Never clean the windscreen with any liquid solution without first removing the windscreen from the microphone boom 1 Hold the windscreen loosely by the plastic retaining ring at its base 2 Gently pull the windscreen a
5. NG THE HEADSET Place the headset wireframe around your head so that the elastic headband band lay hor izontally across the back of your head and the ends of the wireframe fit over your ears You may position the elastic headband either above or below the wireframe for the great est comfort and stability The blue SHURE logo should face outward see Figure 2 WEARING THE HEADSET POSITIONING THE MICROPHONE FIGURE 2 FIGURE 3 POSITIONING THE MICROPHONE For maximum gain before feedback position the microphone and boom so that the mi crophone is within 13 mm 1 2 inch of the right corner of your mouth see Figure 3 This will also help minimize breath noise or popping ADJUSTING THE HEADSET e If the headset feels loose or uncomfortable carefully bend the sides of the wire frame to make it tighter or looser see Figure 4A The angle of the wireframe ear pieces may also need adjustment see Figure 4B ADJUSTING THE WIREFRAME FIGURE 4 e Adjust the tension of the elastic headband across the back of the head by sliding it up or down the ends of the wireframe see Figure 5 gt ADJUSTING THE ELASTIC HEADBAND FIGURE 5 USING THE CABLE RETAINER AND CLOTHING CLIP Use the cable retainer on the wire frame of the headset to position the microphone cable as desired The supplied spring loaded clothing clip secures the microphone cable to the user s clothing to help avoid entanglement CONNECTING THE WH30 TO A SOUN
6. mic securely in place Isolation shock mount for reduced handling noise Matte black finish for low visibility High input clipping level helps avoid overload distortion Low self noise and high sound pressure level capability Reliable at temperature and humidity extremes MODEL VARIATIONS WH30TQG For wireless use the WH30TQG has a 1 2m 4 ft high flex cable and a mini connector for direct connection to Shure body pack transmitters Note For information about use with Shure W10BT or other transmitters without a mini TA4F connector contact Shure Customer Service WHSOXLR For wired applications the is supplied with a 1 2m 4 ft hi flex cable and high quality mic preamplifier RPM420 with a three pin XLR con nector The RPM420 preamplifier requires phantom power from any 11 52 V source MICROPHONE PARTS The WH30 consists of the following parts see Figure 1 Microphone Cartridge and Windscreen 2 Microphone Boom and Cartridge Housing 3 Isolation Shock Mount Boom Hinge rotates as shown Cable Elastic Headband Wireframe RPM420 Preamplifier WH30XLR only A DO WH30 HEADSET MICROPHONE PARTS FIGURE 1 COLLAPSIBLE MICROPHONE BOOM The WH30 headset features a collapsible boom for shipment and storage Before wearing the headset unfold the boom by rotating it away from the wireframe until it snaps into place Refold for storage or transportation WEARI
7. way from microphone The plastic retaining ring will expand to allow the windscreen to slip off the microphone If necessary you can expand the ring manually with a small screwdriver as you pull the windscreen 3 Immerse the windscreen in mild soapy water and gently squeeze it several times 4 Rinse the windscreen in clean water and dry it with a clean cloth or paper towel Allow it to air dry thoroughly 5 When the windscreen is dry slide it over the WH30 microphone until the retain ing ring snaps into place CERTIFICATION WH30XLR Conforms to European EMC Directive 89 336 EEC and is eligible to bear the CE marking Meets applicable tests and performance criteria in European standard EN 55103 1996 parts 1 and 2 for residential E1 and light industrial E2 environments WH30TQG Conforms to European EMC Directive 89 33 EEC and is eligible to bear the CE marking Meets EMC require ments as an ancillary device per EN 300 445 1996 REPLACEMENT PARTS Cable Connector for WA330 Connector Belt Clip for WH30XLR RK200BC Elastic Headbard iii oit ae 80A505B Wireframe Headband Boom Hinge Boom Shock Mount Cartridge Housing and Cable RPM520 cce EE RPM420 Black Windscreens 2 and Clothing
Download Pdf Manuals
Related Search