Sharp TCADH2564RCZZ User's Manual
Contents
1. caught by the printer auto feed and comes out the top of the printer If the printer does not catch the paper feed the paper while pressing as illustrated in step 3 Insert the end of the paper into the slit in the take up spool and fold the paper to front side then wind the paper two or three turns around the spool shaft Press to feed more paper if required Set the spool on the bearing and press the key to take up excess slack in the paper Replace the printer cover 5 Basic Programming Set the mode switch to the PGM position E Setting the Date Enter the date in 8 digits using the month day year format Then press f wsn Example 0 2 2 6 C 0 G C 0 emen Date February 26 2010 E Setting the Time Enter the time in 4 digits hhmm format using the 24 hour system Then press wssn Example 1 4 3 C_ 0 pms Time 2 30 p m E Setting Tax Rates NOTE If you are in an area that uses a tax table for tax calculation please refer to the programming section in the instruction manual Specify a tax rate for calculation of tax on each taxable subtotal using the following sequence msi gt 9 gt C gt Tax number 1 to 4 gt gt Tax rate 0 0000 to 100 0000 gt gt Minimum taxable amount 0 01 to 999 99 gt TwSBTL gt cwatins Smallest amount for which tax must be collected NOTE Up to 4 types of tax are programmable for Tax 1 through Tax2. 4 Example1 Set state tax 6 25 with tax exempt as 12 men 9 Cr GA OCODE GOC emen warns Tax1 Tax rate 6 25 Min taxable amount 0 12 Example2 Set state tax 4 with tax exempt as 0 amsn 9 ro Ger CA femen CWATINS Tax1 Tax rate 4 E Other Programming The cash register is pre programmed so it can be used with minimal set up For optional features please refer to the instruction manual Initial settings Department 1 to 10 Taxable 1 Department 11 to 99 Non taxable NOTE To scan barcodes using the barcode scanner their preset unit prices associated departments and item labels should be programmed 6 Now you are ready E Before Starting Entries e Set the mode switch to the REG position REG OPX Z OFF ZF e Enter a clerk code 1 to 40 and press cixksiconv Once the clerk code is entered re entry of the clerk code is not needed until the clerk is changed Example 1 ciksicony Clerk code E Registration Example when selling department items by cash Turn the mode switch to REG position Enter your clerk code A cuksicony Clerk code Enter the price for the first department item For example for 5 00 enter 5 0 and press the appropriate department key Price and dept 1 For department 21 to department 40 press first before 8 2 S pertsHrT gt 7 pressing the department key Price and dept 22 For department 41 and above enter the department number using
3. XE A506 Quick Start Guide English The following describes how to get the cash register ready for operation Follow these steps before using the cash register for the first time Place the cash register on a stable flat surface not subject to direct sunlight g f Connecting the Barcode Scanner A barcode scanner is provided with the cash register To use the scanner connect the scanner before turning on the register 1 Open the Scanner port cover at the right side of the register Insert the connector of the barcode scanner into the Scanner port and tighten both screws on the connector CAUTION Always unplug the power cord of the cash register when you connect or disconnect the barcode scanner e Never connect devices other than the barcode scanner before changing the interface setting Otherwise malfunction of the cash register will occur Preparing the Cash Register 1 Push the printer cover forward and detach it 2 Remove the white retainer at the position shown right NOTE Please keep this retainer for future use when transferring the cash register 3 Move the print head release lever upwards as illustrated right Print head N release lever Initializing the Cash Register To ensure the cash register operates properly please use the following procedure 1 Make sure the power cord plug is not inserted into the AC outlet 2 Insert the manager MA key into the mode switch and turn it
4. numeric keys and press et then enter the price and press et again Repeat step 3 for all the department items Press to display the amount due TMISBTL Enter the amount received from the customer You can omit 2 0 0 this step if the amount tendered is the same as the subtotal Amount tendered Press cwats and the change due is displayed when the amount received was not entered total amount is displayed and the drawer is opened Tear off the receipt and give it to the customer with his or her change 9 Close the drawer NOTE When you scan a barcode using the barcode scanner without programming the cash register goes into the learning function mode For details of this mode please refer to the instruction manual How to download Customer Support Tool Customer Support Tool can be downloaded from the Sharp web site Please visit the Sharp web site http Awww sharpusa com registersoftware When an error occurs When an error occurs with an alarm sound press CL to clear the error If you do not clear the error press twice The transaction will be finalized in subtotal void or cash sale Printed in China TCADH2564RCZZ
5. to the PGM position REG OPX Z wm MGR OFF we X1 Z1 VOID x2 Z2 PGM While holding down both the 4 key and the CL key insert the plug into the AC outlet The buzzer will sound three times and MRS will be displayed The cash register has now been initialized The register display will show 0 00 with PGM CAUTION To charge the rechargeable batteries keep the power on for one or two days Leave the register with the mode switch in a position other than OFF NOTE If you press a key by mistake an error message may be displayed Press the CL key to clear message after installing paper rolls 74 Installing the Paper Rolls of each paper roll Make sure the 1 Cut off approximately one revolution paper end is cut as illustrated right Incorrect For receipt paper installation 2 Seta paper roll in the paper cradle Qu of the receipt side upper side as Correct illustrated right Z OMJ To the printer To the printer Incorrect Insert the end of the paper into the paper chute until it is caught by the printer auto feed and comes out the top of the printer If the printer does not catch the paper feed the paper while pressing Cut off the excess paper with the paper cutter For journal paper installation Set a paper roll in the paper cradle of the journal side as illustrated in step 2 Insert the end of the paper into the paper chute until it is
Download Pdf Manuals
Related Search