Sharp LL-S201A User's Manual
Contents
1. Model LL S201A LCD component 20 Class 19 1 2 inch 49 5cm diagonal TFT LCD Max resolution pixels 1920 x 1080 Max colors Approx 16 77 million colors Pixel pitch 0 225 mm H x 0 225 mm V Viewing angle 178 right left up down contrast ratio 2 10 Screen active area inch 17 x 9 9 16 432 x 243 Plug and play VESA DDC2B Color adjustment Image quality Normal Pen Writing Game Multimedia User menu Color temperature 9000K 7500K 6500K 5000K and 4200K With individual RGB adjustment and adjustment reset functions Input terminals HDMI x 1 HDMI MHL DisplayPort x1 Output terminals Headphones 3 5 mm mini stereo jack 1 Speaker output 1W 1W Touch Panel Touch screen system Capacitive USB for touch panel x1 microUSB Type B Ver 1 1 communication Maximum touch points 10 points Power requirement AC 100 V 240 V 50 60 Hz when using the supplied AC adapter DC 19V Operating temperature 32 F to 95 F 0 C to 35 C Operating humidity 20 to 80 no condensation Power consumption 26 W 35 W 0 5 W when using the supplied AC adapter During normal operation when MHL charging during standby Dimensions excluding protrusions inch Approx 18 1 4 W x 1 D x 10 13 16 463 8 x 25 2 x 274 8 Weight Ibs Approx 5 07 2 3 excluding the stand Approx 6 39 2 9 including on stand When the DisplayPort input terminal and Micro USB2. 14 Part Names 8 Other functions sia el 16 Binding 9 Cautionary nari 16 Connecting Peripheral Equipment 9 Monitor Settings 17 Connection PC 9 17 Connecting headphones commercially available 10 Menu functions ns virili 18 Connecting the monitor to a power source 10 SETUP Menu 19 Installationi cigii nani cu inizi iii inci 11 Prohibiting operations operation 20 Standing position iaia iaia 11 Monitor status indicators 21 Pen writing position aria 12 5 22 Horizontal positioN i 12 Specifications cvssccnicii rire ni cicci iii 23 For information on the Pen Software see the Pen Software Operation Manual Supplied Components If any component should be missing please contact your dealer Liquid Crystal Display Monitor 1 adapter 1 Power cord USB cable USB microUSB Type 1 O CD ROM Utility Disk 1 O Stand front back bottom cover fixing screws 2 1 O Setup Manual 1 Touch pen 1 SHARP Corporation holds authorship rights to the Utility
3. Disk program Do not reproduce it without permission Keep packaging for use when transporting monitor etc System Requirements mTouch Panel To use the touch panel the monitor must be connected to a computer using a USB cable Touch panel operating conditions are as described below Computer PC AT compatible computer with a USB 1 1 port and able to output a resolution of 1920 x 1080 OS Windows 8 32 bit or 64 bit version Windows 7 32 bit or 64 bit version Windows Vista 32 bit or 64 bit version Windows XP 32 bit or 64 bit version e Windows 7 or later is recommended for touch action Windows 7 and later the touch panel operates with the standard Window driver On Windows Vista XP you must install the touch panel driver to your PC from the included CD ROM mPen Software Operating conditions for the included Pen Software are as described below To install Pen Software refer to the Pen Software Operation Manual Pen Software is for use with monitors installed in landscape orientation PC AT compatible computer able to output a resolution of 1920 x 1080 CD ROM drive required for software installation Windows 8 32 bit or 64 bit version Windows 7 32 bit or 64 bit version Windows Vista 32 bit or 64 bit version Windows XP 32 bit or 64 bit version Computer OS CPU Intel Celeron or AMD Sempron 1 6 GHz or faster Intel Core 2 Duo or AMD Athlon Il X2 2 8 GHz or faster recommended Memory A
4. a sharp pencil Depending on the application used the supplied touch pen may not function If another USB device is connected to the computer to which the touch panel is connected do not operate the USB device during touch panel input Input may not take place correctly Do not use liquid such as alcohol in cleaning the screen Keep all cables off the touch panel Not doing so may lead to LCD monitor malfunctions If used in a room or location with drastic temperature differences the display quality of the screen and the quality of touch panel performance may decrease TIPS AND SAFETY INSTRUCTIONS The Power Cord and AC adapter Use only the power cord and AC adapter supplied with the monitor When handling the AC adapter observe the following Incorrect handling may result in fire electric shock or injury Do not drop the AC adapter or subject it to impact Never disassemble the AC adapter It contains high voltage parts that are dangerous to touch The AC adapter is for indoor use only Do not use it outside Do not use the supplied AC adapter with other devices Do not damage the power cord and AC adapter nor place heavy objects on it stretch it or over bend it Also do not add extension cords Damage to the cord may result in fire or electric shock Do not use the power cord with a power tap Adding an extension cord may lead to fire as a result of overheating Do not remove or insert the pow
5. bottom cover Align the arrow on the bottom cover so that it points toward the front and press the projections on the bottom cover into the pocket on the front and back Front Back i TIPS Back pocket The stand and the monitor can be secured with fixing screws Front pocket Fixing screws supplied 77 11 Installation mDisassembling the stand Horizontal position 1 Remove the bottom cover Push the tabs in towards the center and pull Place the monitor on a table or other level surface e When using the monitor horizontally use the horizontal tab in the upright position 1 Lift up the two tabs on the back of the monitor Bottom cover 2 Remove the back from the front Depress the button on the front and slide the back across then pull the back up Back Button wr Front 2 Place the monitor where you want to use it Pen writing position Place the monitor at an angle on a table or other level surface 1 Hold the flap by the depression on the back of the monitor and pull the flap up Do not exert a large amount of force on the monitor from above Doing so may damage the tabs 2 1 Depression 2 Place the monitor where you want to use it _ not exert large amount of force on the monitor from above Doing so may damage the flap 12 Turning Power On Off Turning on the power 1 Press the POWER button POWER bu
6. DS data 1 14 N C 4 MainLane 2 14 Gnd 5 TMDS data 1 shield 15 SCL 5 Gnd 15 Aux 6 TMDS data 1 16 SDA 6 MainLane 2 16 Gnd 7 TMDS data 0 17 DDC CEC GND 7 MainLane 1 17 Aux 8 TMDS data 0 shield 18 5V 8 Gnd 18 Hot plug detection 9 TMDS data 0 19 Hot plug detection 9 MainLane 1 19 Gnd 10 TMDS clock 10 MainLane 0 200 3 3 V 256 SHARP SHARP CORPORATION LL S201A Me EN13A 1
7. Finger pen mode This icon switches the touch action mode to finger pen mode The touch mark becomes the finger pen mark Pen only mode This icon switches the touch action mode to pen only mode The touch mark becomes the pen mark Finger only mode This icon switches the touch action mode to finger only mode The touch mark becomes the finger only mark Rotation This icon lets you rotate the screen 180 When the monitor is rotated a W mark is displayed at the top of the icon The rotate mark also appears on the screen See pages 19 21 4 Volume This icon adjusts speaker and headphone volume Touching Mute temporarily sets the volume to 0 Touching Mute again returns the volume to the previous level 18 lt O Rotation iFinger only Finger pen mode mode mode _ Touch mode selection El This icon manually switches the signal input source from the PC Touching the icon displays HDMI and DisplayPort A PP mark is added to the input source being displayed Setup This icon configures the monitor For details on individual settings see page 19 Input Select SETUP Menu Details Position Position When the monitor is used in portrait orientation power menu button on the top this icon moves the display position of the menu screen to the bottom of the screen Ce Mode Mode Normal This mode is suited to norma
8. SAFETY PRECAUTIONS Electricity is used to perform many useful functions but it can also cause personal injuries and property damage if improperly handled This product has been engineered and manufactured with the highest priority on safety However improper use can result in electric shock and or fire In order to prevent potential danger please observe the following instructions when installing operating and cleaning the product To ensure your safety and prolong the service life of your LCD product please read the following precautions carefully before using the product 1 2 A Read instructions All operating instructions must be read and understood before the product is operated Keep this manual in a safe place These safety and operating instructions must be kept in a safe place for future reference Observe warnings All warnings on the product and in the instructions must be observed closely Follow instructions All operating instructions must be followed Cleaning Unplug the power cord from the AC outlet before cleaning the product Use a dry cloth to clean the product Do not use liquid cleaners or aerosol cleaners Attachments Do not use attachments not recommended by the manufacturer Use of inadequate attachments can result in accidents Water and moisture Do not use the product near water Do not install the product in a place where water may splash onto it Be careful of equipment which drains
9. SHARP LL 5201A LCD MONITOR OPERATION MANUAL HIGH DEFINITION MULTIMEDIA INTERFACE Mobile High Definition Link Attention Your product is marked with this symbol It means that used electrical and electronic products should not be mixed with general household waste There is a separate collection system for these products A Information on Disposal for Users private households 1 In the European Union Attention If you want to dispose of this equipment please do not use the ordinary dustbin Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment recovery and recycling of used electrical and electronic equipment Following the implementation by member states private households within the EU states may return their used electrical and electronic equipment to designated collection facilities free of charge In some countries your local retailer may also take back your old product free of charge if you purchase a similar new one Please contact your local authority for further details If your used electrical or electronic equipment has batteries or accumulators please dispose of these separately beforehand according to local requirements By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment recovery and recycling and thus prevent potential negative effects on the environment and human healt
10. ace such as a desk and gently place the monitor on it with the screen facing down e Be sure to turn off the power and disconnect the plug from the power outlet before connecting disconnecting cables Also read the manual of the equipment to be connected Do not forcibly bend or apply force to cables Doing so may result in wire breakage or other damage e When connecting cables spread a soft cloth on a stable level surface such as a desk and gently place the monitor on it with the screen facing down Do not use any cable that has a damaged or deformed terminal Using such cables may cause malfunctions TPs Images may not be displayed properly depending on the computer video card to be connected Connection with a PC Connect the monitor and a PC using the connection cable inputting video and audio HDMI input terminal Commercially available HDMI cable conforming to the HDMI standard To HDMI output terminal on PC HDMI input terminal Check the orientation of the connector and insert it horizontally as far as it will go e It is possible to connect the monitor s HDMI input terminal to a smartphone or similar MHL compliant device using a commercially available MHL cable This production incorporates MHL 1 Commercially available DisplayPort cable To DisplayPort ou
11. ark rotation mark key mark on the screen Screen This setting configures whether or not to display the logo screen during startup On The logo screen is displayed when the monitor starts Off The logo screen is not displayed when the monitor starts Mode Mode1 If there is no operation for 4 hours or more the monitor automatically turns off the power Mode2 Will perform standard operation Language Language This setting changes the menu screen display language So Reset Reset This setting resets all settings to their factory default 19 Monitor Settings Prohibiting operations operation lock Operation lock is enabled A key mark is displayed on the screen and it disappears This function makes it possible to prohibit operations to turn after around 5 seconds the power off and to prohibit touch action on the screen If an operation is attempted when the monitor is locked a key mark is displayed for around 5 seconds See page 21 Ifthe menu screen is displayed when locked the invalid action mark is displayed e When the MENU button is pressed the menu screen appears and only the disable operation lock and exit menu operation are possible Locking operation 1 Press the MENU button The menu screen appears 6 MENU button In
12. ch Action Other functions In Windows 8 input panel functions can be used In Windows 7 touch pointer and input panel functions can be used For information about the touch pointer and input panel functions see Windows Help Touch pointer A translucent image of a mouse appears near the point touched The left right buttons of the image can be clicked to perform the same actions as left right clicking a mouse Input panel A software keyboard and an input panel with handwriting recognition appear on the screen Windows 8 and Windows 7 excluding Starter the ink function of Microsoft Office can be used Handwritten comments can be written and handwriting can be recognized For details see Microsoft Office Help Cautionary points e When performing touch actions use the ball of your finger e When performing pen actions use the included touch pen Do not use the touch pen for any purpose other than touch panel operation Do not press hard on the tip of the touch pen there is dirt or foreign matter on the tip of the touch pen remove it Failure to do so may damage the screen e Even when in pen only mode the monitor may respond to objects other than the included touch pen e When performing pen actions with the included touch pen do not touch the screen with anything other than the hand that is holding the pen Monitor Settings Menu operations 4 Touch Exit or press the MENU button The men
13. d 15 the USB cable connected properly See page 10 e The touch panel may not work properly if there is a large contact area e g if the screen is touched with the palm of the hand Is the monitor pen only mode Touch action is disabled in pen only mode See page 14 page 18 Is the monitor in finger only mode You cannot touch the screen with the touch pen when in finger only mode See page 14 page 18 Are monitor operations locked See page 20 e When there is no signal input to the LCD monitor actions on the touch panel are not possible Please operate the PC using the mouse and keyboard The response of the touch screen is slow Some parts of the screen do not respond e When starting your computer or connecting the USB cable do not touch the touch panel e When starting the LCD monitor do not touch the screen If the screen is touched the monitor may not function correctly In this situation turn off the LCD monitor power wait 5 seconds or longer and then turn the power on again e While the menu screen is displayed touch actions are not possible other than those for the menu screen First exit the menu screen and then perform the operation e There may be no response if the included touch pen and your hand on the screen are too close In this situation perform the operation with the pen and your hand separated farther apart 22 Specifications mProduct Specifications
14. d Micro Devices Inc MHL the MHL logo and Mobile High Definition Link are trademarks or registered trademarks of MHL LLC in the United States and other countries All other brand and product names are trademarks or registered trademarks of their respective holders Language of OSD menu used in this manual is English by way of example Illustrations in this manual may not exactly represent the actual product or display LED Backlight e The LED backlight in this product has a limited lifetime If the screen gets dark or does not turn on it may be necessary to replace the LED backlight This LED backlight is exclusive to this product and must be replaced by an authorized SHARP servicing dealer or service center Please contact your local SHARP servicing dealer or service center for assistance Contents IMPORTANT 3 Turning Power ON Off en 13 DEAR SHARP 4 Turning on the power 13 SAFETY 4 Turning off the power 13 TIPS AND SAFETY INSTRUCTIONS 6 Touch Actioun aaa 14 Supplied 7 Touch action MOdEs 14 System Requirements na 7 Touch
15. er plug with wet hands Doing so could result in electric shock Unplug the power cord if it is not used for a long time Do not attempt to repair the power cord if it is broken or malfunctioning Refer the servicing to the service representative Do not stay in contact with the parts of the product and the AC adapter that become hot for long periods of time Doing so may result in low temperature burns For your health observe the following If using the monitor continuously take 10 to 15 minute break every hour to rest your eyes not use the monitor in high contrast light conditions Do not use the monitor in locations where the screen is subject to direct sunlight Manual Scope Microsoft Windows and Windows Vista are registered trademarks of Microsoft Corporation The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries DisplayPort is a registered trademark of Video Electronics Standards Association Adobe Acrobat and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries Intel Celeron and Intel Core 2 Duo are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the U S A and other countries AMD AMD Sempron AMD Athlon and combinations thereof are trademarks of Advance
16. h which could otherwise arise due to inappropriate waste handling 2 In other Countries outside the EU If you wish to discard this product please contact your local authorities and ask for the correct method of disposal For Switzerland Used electrical or electronic equipment can be returned free of charge to the dealer even if you don t purchase a new product Further collection facilities are listed on the homepage of www swico ch or www sens ch B Information on Disposal for Business Users 1 In the European Union If the product is used for business purposes and you want to discard it Please contact your SHARP dealer who will inform you about the take back of the product You might be charged for the costs arising from take back and recycling Small products and small amounts might be taken back by your local collection facilities For Spain Please contact the established collection system or your local authority for take back of your used products 2 In other Countries outside the EU If you wish to discard of this product please contact your local authorities and ask for the correct method of disposal IMPORTANT INFORMATION WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE The lightning flash with arrowhead symbol within CAUTION a triangle is intended to alert the user to the presence of uninsulated dangerous voltage RISK OF ELECTRIC wi
17. he manufacturer e Only using furniture that can safely support the monitor e Ensuring the monitor is not overhanging the edge of the supporting furniture placing the monitor on tall furniture for example cupboards or bookcases without anchoring both the furniture and the monitor to a suitable support e Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture e Educating children about the dangers of climbing on furniture to reach the monitor or its controls 5 6 The TFT color LCD panel used in this monitor is made with the application of high precision technology However there may be minute points on the screen where pixels never light or are permanently lit Also if the screen is viewed from an acute angle there may be uneven colors or brightness Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor Do not display a still picture for a long period as this could cause a residual image Never rub or tap the monitor with hard objects Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party nor for any other malfunctions or damage to this product arising during use except where indemnity liability is recognized under law This monitor and its accessories may be upgraded without advance notice Do not use the monit
18. ications mSupported frequency 640x480 60Hz 800x600 60Hz 1024x768 60Hz 720 480 59 94 60Hz 1280 720 50 59 94 60Hz 1920 1080 50 59 94 60Hz 720 576 50Hz All are compliant only with non interlaced Each is scaled to 16 9 and displayed using the full screen Depending on the connected PC images may not be displayed properly even if the compatible signal described above is input EDDC plug and play The monitor supports the VESA DDC Display Data Channel standard DDC is a signal standard for plug and play between monitors and computers Information about resolution and other parameters is exchanged between the two This function can be used if the computer supports DDC and it has been configured to detect plug and play monitors There are several types of DDC depending on the communication method used This monitor supports DDC2B HDMI input terminal pins EDisplayPort input terminal pins HDMI Connector DisplayPort 20 pin oI Ana g A Function Function No Function No Function 1 TMDS data 2 11 TMDS clock shield 1 MainLane 3 11 Gnd 2 TMDS data 2 shield 12 TMDS clock 2 Gnd 12 MainLane 0 3 TMDS data 2 13 CEC 3 MainLane 3 13 Gnd 4 TM
19. icing Repair If any of the following conditions occurs unplug the power cord from the AC outlet and request a qualified service person to perform repairs a When the power cord or plug is damaged b When a liquid was spilled on the product or when objects have fallen into the product c When the product has been exposed to rain or water d When the product does not operate properly as described in the operating instructions Do not touch the controls other than those described in the operating instructions Improper adjustment of controls not described in the instructions can cause damage which often requires extensive adjustment work by a qualified technician e When the product has been dropped or damaged f When the product displays an abnormal condition Any noticeable abnormality in the product indicates that the product needs servicing Replacement parts In case the product needs replacement parts make sure that the service person uses replacement parts specified by the manufacturer or those with the same characteristics and performance as the original parts Use of unauthorized parts can result in fire electric shock and or other danger Safety checks Upon completion of service or repair work request the service technician to perform safety checks to ensure that the product is in proper operating condition Wall mounting When mounting the product on a wall be sure to install the product accord
20. ing to the method recommended by the manufacturer Heat sources Keep the product away from heat sources such as radiators heaters stoves and other heat generating products including amplifiers SAFETY PRECAUTIONS Continued 19 Usage of the monitor must not be accompanied by fatal risks or dangers that could lead directly to death personal injury severe physical damage or other loss including nuclear reaction control in nuclear facility medical life support system and missile launch control a weapon system 20 Do not touch the parts of the product or the AC adapter that become hot for long periods of time Doing so may result in low temperature burns To maintain compliance with EMC regulations use shielded cables to connect to the following terminals HDMI input terminal and DisplayPort input terminal This product is designed for commercial application only and as such it falls outside the scope of Regulation EC 1275 2008 implementing EU Directive 2005 32 EC on eco design requirements for standby and off mode electric power consumption SHARP do not recommend the product for domestic application and will not accept any liability for such use If a monitor is not positioned in a sufficiently stable location it can be potentially hazardous due to falling Many injuries particularly to children can be avoided by taking simple precautions such as e Using fixing devices like wall mount brackets recommended by t
21. l PC screen display Pen Writing This mode is suited to pen writing position Game This mode is suited to video games Multimedia This mode is suited to video playback User The user can adjust the image quality Brightness x Brightness This icon adjusts the brightness of the backlight Other on Start Up Touch Mode This setting configures the touch action mode See page 18 used when the monitor is turned on Reset The monitor starts in finger pen mode Save The monitor starts in the mode that was last used Rotate Mode This setting configures the rotate setting See page 18 used when the monitor is turned on Reset The monitor starts with rotate disabled Save The monitor starts in the mode that was last used Position This setting configures the menu display position used when the monitor is turned on Reset The monitor starts with the menu display position on the bottom of landscape orientation Save The monitor starts in the mode that was last used Monitor Settings Touch Mark This setting configures how to display the touch mark See page 21 Rotation Mark This setting configures how to display the rotation mark See page 21 Key Mark This setting configures how to display the key mark See page 20 Mark Position This setting configures the display position of the status display mark touch m
22. le the menu screen is displayed 21 Troubleshooting If you are experiencing any problem with your display before calling for service please review the following troubleshooting tips There is no picture or sound e Are the AC adapter and power cord connected correctly See page 10 15 the power on See page 13 There is a picture but no sound e Make sure the volume is not set to minimum See page 18 Is the sound muted See page 18 e When headphones are connected no sound will come from the speakers See page 10 e No sound will come from the speakers when the monitor is in standby mode when the power LED is orange See page 13 The video does not appear 15 the cable certified for HDMI or DisplayPort The monitor will not work unless a standards compliant cable is used e Is the input signal compatible with this monitor See page 25 e 15 the monitor connected correctly to the PC Is the PC turned on Is the PC in power saving mode Try pressing a key on the keyboard or moving the mouse e Turn off the LCD monitor power wait 5 seconds or longer and then turn the power on again The video does not appear properly Ifa powerful amount of strain is exerted on the touch display a portion of the display may remain on the screen In this situation turn off the monitor power wait 5 seconds or longer and then turn the power on again The touch panel does not respon
23. nger touch pen I N vi Double tap Quickly touch the screen twice with your finger touch pen N Swipe Touch the screen with your finger touch pen move without lifting and then stop Swipe from edge of screen After touching the edge of the monitor with your finger touch pen move horizontally without releasing your finger touch pen and then stop lt a gt Touch Action Drag and drop Finger actions Touch the screen with your finger pen and move without lifting Zoom When you have finished the movement lift your finger touch While touching the screen with two fingers move them closer together and farther apart iy Slide to pan With your finger touch pen touching the screen move it up and down to scroll the screen Stretch Flick Press and tap uo fi ouch in a flicki ti With one finger touching the screen tap once single tap with ove your finger touch pen in a flicking motion another finger Tap once single tap with another finger N Flick your finger NF 74 With one finger touching Press and hold Rotate Press briefly with your finger touch pen and then lift your While touching the monitor with one finger move the other finger touch pen from the screen finger in the direction you wish to rotate in Move another finger in the desired direction of rotation With one finger touching 15 16 Tou
24. or where there is poor ventilation where there is a lot of dust where humidity is high or where the monitor may come into contact with oil or steam Ensure that the monitor does not come into contact with water or other fluids Ensure that no objects such as paper clips or pins enter the monitor as this could lead to fire or electric shock Do not place the monitor on top of unstable objects or in unsafe places Do not allow the monitor to receive strong shocks or to strongly vibrate Causing the monitor to fall or topple over may damage it Continuous Operation Time and Warranty This product has been designed based on the assumption of 15 or fewer hours of usage in one day Continuous usage that exceeds 15 hours in one day is not covered by the warranty Do not use the monitor near heating equipment or in places where there is likelihood of high temperature as this may lead to generation of excessive heat and outbreak of fire Do not use the monitor in places where it may be exposed to direct sunlight The AC outlet shall be installed near the equipment and shall be easily accessible Do not touch the screen when starting the LCD monitor If the screen is touched the monitor may not function correctly In this situation turn the LCD monitor off wait at least 5 seconds and then turn on the monitor again Do not operate the screen with a hard or pointed object such as a fingernail pen other than the included touch pen or
25. r with the touch pen While the screen is being touched with the touch pen touch pen operation is given priority and you cannot touch the screen with your finger Once the touch pen has been moved away from the screen for around 1 second you can touch the screen with your finger Pen only mode This mode is for touch pen use only You cannot touch the screen with your finger You can touch the menu screen See page 17 with your finger Finger only mode This mode is for finger use only You cannot touch the screen with the touch pen Touch action Touch actions that can be used with this monitor differ according to operating system and application The functions of touch actions are also different For details check Windows Help and the application s support documentation Windows Vista Windows XP Yes Windows 8 Windows 7 Touch action Single tap Yes Yes Double tap Yes Yes Yes Yes Yes Yes Yes No No Swipe Swipe from edge of screen Drag and drop Yes Slide to pan Flicks Press and hold Zoom Press and tap Rotate You must install the touch panel driver to your PC from the included CD ROM TPs In Windows 7 if the checkmark has been removed from Enable multi touch gestures and inking in Pen and touch in Control Panel select the checkbox 14 mCommon finger and touch pen actions Single tap Touch the screen with your fi
26. t least 2 GB at least 1 GB for Windows XP Free space on hard drive At least 100 MB free space separately required for data storage 8 Part Names BFront view 1 Power LED See page 13 BRear view 1 Flap See page 12 2 VESA holes See page 24 3 Anti theft hole Allows the monitor to be secured using a commercially available anti theft lock The anti theft hole is compatible with Kensington s MicroSaver security system 4 Speakers 5 Power Menu button See page 13 page 17 6 Cable clamp See page 9 7 Headphone jack See page 10 8 HDMI input terminal See page 9 9 DisplayPort input terminal See page 9 10 Micro USB terminal See page 10 11 AC adapter connection terminal See page 10 12 Tabs See page 12 Binding Cables Secure the HDMI cable DisplayPort cable and USB cable using the cable clamp 1 Remove the cable clamp restraint slot 2 Route the cables through the cable 27 3 Push the cable clamp down into place 27 Cable restraint slot Cable clamp Cable clamp e When connecting cables spread a soft cloth on a stable level surf
27. ted using Volume on the menu screen See page 18 e The volume is set to 0 when the monitor is shipped from the factory Connecting the monitor to a power source e Use only the AC adapter and power cord supplied with the monitor 1 Connect the monitor to the power outlet using the supplied AC adapter and power cord Back of monitor For power outlet i 888888383 AC adapter connection terminal dt a Power cord AC adapter Supplied Supplied Core restraine AC adapter core 2 Push the AC adapter core into the core restrainer 10 Installation The monitor can be installed in three different ways mMounting the monitor the stand 1 Place the stand on a level surface Standing position Place the monitor on the supplied stand e The stand is for use in landscape orientation It cannot be used for portrait orientation mAssembling the stand 2 Set the monitor on the stand 4 insartitia back into the front Set the monitor so that the logo in the center is aligned with ur er the circle mark on the stand Align the mark A on the front with the edge of the back and insert the back from above Back g J Logo Front 2 Slide the back across Slide the back until it clicks into place Circle mark Back 3 Attach the
28. terminal are connected As a part of our policy of continuous improvement SHARP reserves the right to make design and specification changes for product improvement without prior notice The performance specification figures indicated are nominal values of production units There may be some deviations from these values in individual units 23 Specifications Dimensional Drawings Note that the values shown are approximate values 18 1 4 463 8 1 25 2 excluding protrusions 18 1 4 463 8 Opening width 17 432 RI 10 13 16 274 8 Opening height 9 9 16 243 10 13 16 274 8 VESA holes 1 15 16 1 15 16 50 50 Unit inch mm 27 50 1 15 16 1 15 16 50 Use a VESA compliant mounting bracket capable of supporting 4 times the weight of the monitor When attaching a VESA compliant mounting bracket use M4 screws that are 3 16inch to 1 4inch 4 to 6 mm longer than the thickness of the mounting bracket When mounting the monitor on a wall or ceiling ensure that the mounting location is capable of supporting 4 times the weight of the monitor e g a concrete wall or column mStanding position 11 13 16 300 6 8 9 16 217 6 9 16 167 024 EPen writing position 9 16 13 9 10 13 16 275 3 Specif
29. thin the product s enclosure that may be of SHOCK sufficient magnitude to constitute a risk of electric DO NOT OPEN shock to persons The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL NOTE FOR USERS IN U K IMPORTANT The wires in this mains lead are coloured in accordance with the following code BLUE NEUTRAL BROWN LIVE CONNECTING PLUG TO MAINS LEAD As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plugs proceed as follows The wire which is coloured BLUE must be connected to the terminal which is marked with the letter or coloured BLACK The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED CAUTION Do not connect the Live BROWN wire or the neutral BLUE wire to the earth terminal of your 3 pin mains plug 4 DEAR SHARP CUSTOMER Thank you for your purchase of a SHARP LCD product To ensure safety and many years of trouble free operation of your product please read the Safety Precautions carefully before using this product
30. tput terminal on PC DisplayPort input terminal Check the orientation of the connector and insert it horizontally as far as it will go e The length of the signal cables or surrounding environment may affect the image quality e The video from the terminal that has signal input is displayed In this state even if a signal is input from the other terminal the display is not switched To switch the display use Input Select on the menu screen See page 18 e Ifthe LCD monitor is turned on when there are input signals from both terminals the video from the DisplayPort input terminal is displayed 9 Connecting Peripheral Equipment mUsing the touch panel Connecting headphones To use the touch panel connect the monitor to a USB port on a PC using the supplied USB cable commercially available Headphones commercially available with a stereo mini plug 3 5 mm can be connected to the monitor 3 5 mm stereo mini plug of commercially available headphones Supplied USB cable gt To USB port on PC Headphone jack Micro USB terminal Check the orientation of the connector and insert it horizontally as far as it will go TPs e When headphones are connected it will no longer be possible to hear sound from the monitor s speakers e Volume can be adjus
31. tton Power LED The power LED turns on 2 Turn on the PC The screen appears Green lit Signal input Orange lit e When switching the POWER button off and back on always wait for an interval of at least 5 seconds Rapid switching may lead to errors or malfunctions complete electrical disconnection pull out the main plug No signal input mOperation Mode When the monitor is turned on for the first time after being shipped from the factory the operation mode setting screen will be displayed Set it to Mode1 or Mode2 If there is no operation for 4 hours or more the monitor automatically turns off the power Mode2 Will perform standard operation Even after being set changes can be made using Operation Mode located in the menu of the monitor Turning off the power 1 Turn off the PC 2 Depress the POWER button for around 2 seconds POWER button Depress for around 2 seconds The power LED turns off If the monitor will not be used for a long time disconnect the power plug from the power outlet 13 Touch Action Touch action modes There are three touch action modes finger pen mode pen only mode and finger only mode These modes can be changed on the menu screen The monitor is set to finger pen mode when shipped Finger pen mode In this mode the screen can be touched with your finger o
32. u screen disappears The monitor settings are configured by displaying the menu screen The operations on this page are the basic operations Do not turn off the power while the menu screen is displayed Doing so may initialize the settings e While the menu screen is displayed touch actions are not possible other than those for the menu screen mExample of operation Operations on the menu screen are described here using adjusting the volume as an example 1 Press the MENU button The menu screen appears Touch Return to return to the level above MENU button Press 2 Touch Volume TPs f actions are made the adjustment bar display screen for around 10 seconds the screen returns to the ordinary display screen e The menu screen can also be operated using your finger in pen only mode ano ae 3 Touch the adjustment bar and slide your finger to either side to adjust the volume SC _ Adjustment bar 17 Monitor Settings Menu functions f Setup Input Select Volume Touch mode selection These icons switch the touch action mode D mark is displayed at the top of the icon for the selected mode The mode can be checked with the touch mark located at the upper right portion of the screen See pages 19 21
33. valid action mark Press 2 While touching Volume touch Finger only mode for at least 1 second r 20 Disabling operation lock 1 Press the MENU button The menu screen is displayed MENU button H agoa unan Press 2 While touching Volume touch Finger only mode for at least 1 second Operation lock is disabled Monitor Settings Monitor status indicators Monitor status is displayed at the top right of the screen Touch Mark Rotation Mark Key Mark Touch Mark The touch mark displays the current touch action mode Finger pen mode This mark is displayed during finger pen mode Pen only mode This mark is displayed during pen only mode Finger only mode This mark is displayed during finger only mode After being set it can be set so that it is only displayed for around 5 seconds See page 19 Rotation Mark This mark is displayed when the rotate function is enabled After being set it can be set so that it is only displayed for around 5 seconds See page 19 Key Mark When operation lock See page 20 is set the mark is displayed for around 5 seconds when the screen is touched It can be set to display constantly See page 19 e The display position can be changed from the menu screen See page 19 e These marks are not displayed whi
34. water such as an air conditioner Ventilation The vents and other openings in the cabinet are designed for ventilation Do not cover or block these vents and openings since insufficient ventilation can cause overheating and or shorten the life of the product Do not place the product on a sofa rug or other similar surface since they can block ventilation openings Do not place the product in an enclosed place such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions are followed Power cord protection The power cords must be routed properly to prevent people from stepping on them or objects from resting on them The screen used in this product is made of glass Therefore it can break when the product is dropped or applied with impact Be careful not to be injured by broken glass pieces in case the screen breaks Overloading Do not overload AC outlets or extension cords Overloading can cause fire or electric shock Entering of objects and liquids Never insert an object into the product through vents or openings High voltage flows in the product and inserting an object can cause electric shock and or short internal parts For the same reason do not spill water or liquid on the product Servicing Do not attempt to service the product yourself Removing covers can expose you to high voltage and other dangerous conditions Request a qualified service person to perform serv
Download Pdf Manuals
Related Search