Sharp MX-B400P Owner's Manual
Contents
1. Do not remove the machine casing High voltage parts inside the machine may cause electrical shock CAUTIONS WARNING Do not make any modifications to this machine Doing so may result in personal injury or damage to the machine If you notice smoke a strange odor or other abnormality do not use the machine If used in this condition fire or electrical shock may result Immediately switch off the main power and remove the power plug from the power outlet Contact your dealer or nearest SHARP Service Department ov If a thunder storm begins switch off the main power and remove the power plug from the outlet to prevent electrical shock and fire due to lightning If a piece of metal or water enters the machine switch off the main power and remove the power plug from the power outlet Contact your dealer or nearest SHARP Service Department Using the machine in this condition may result in electrical shock or fire Do not insert or remove the power plug with wet hands This may cause electrical shock Do not use a flammable spray to clean the machine If gas from the spray comes in contact with hot electrical components or the fusing unit inside the machine fire or electrical shock may result OOO CAUTIONS CAUTION Do not install the machine on an unstable or slanted surface Install the ma2. 16K Offset distance 1 25 mm Tray capacity Non stapling 2 280 sheets 20 Ibs to 24 Ibs 75 g m to 90 g m 8 1 2 x 14 8 1 2 x 13 1 2 8 1 2 x 13 2 5 8 1 2 x 13 8 1 2 x 11 7 1 4 x 10 1 2 A4 B5 16K 150 sheets 20 Ibs to 24 Ibs 75 g m to 90 g m2 5 1 2 x 8 1 2 A5 Stapling 2 to 10 sheets per set 30 sets 11 to 30 sheets per set 10 sets 8 1 2 x 14 8 1 2 x 13 1 2 8 1 2 x 13 2 5 8 1 2 x 13 8 1 2 x 11 7 1 4 x 10 1 2 A4 B5 16K Power supply Supplied from the machine Dimensions When tray is folded up 18 45 64 W x 13 7 64 D x 6 7 32 H 475 mm W x 333 mm D x 158 mm H When tray is extended 20 19 32 W x 13 7 64 D x 6 7 32 H 523 mm W x 333 mm D x 158 mm H Weight Stapler section Allowed paper sizes for stapling Approx 19 8 Ibs 9 kg 8 1 2 x 14 8 1 2 x 13 1 2 8 1 2 x 13 2 5 8 1 2 x 13 8 1 2 x 11 7 1 4 x 10 1 2 A4 B5 16K Stapling at one position at front of paper 19 SPECIFICATIONS Finisher specifications Continued Maximum 30 sheets number of sheets for stapling 1 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location the type of paper and the storage conditions of the paper 2 Up to 20 envelopes can be output 3 The maximum number of sheets for stapling assumes a paper weight
3. B5 A5 16K Paper weight Plain paper 16 Ibs to 28 Ibs 60 g m2 to 105 g m2 Paper capacity 500 sheets 21 Ibs 80 g m2 x 1 tray Paper types SHARP recommended plain paper recycled paper and colored paper Automatic paper size detection When Auto Inch detection is selected 8 1 2 x 14 8 1 2 x 11 7 1 4 x 10 1 2 5 1 2 x 8 1 2 When Auto AB detection is selected A4 B5 A5 216 mm x 330 mm 8 1 2 x 13 Power supply Supplied from the machine Dimensions 21 1 16 W x 17 1 4 D x 4 13 32 H 24 1 16 W x 17 1 4 D x 4 21 64 H 535 mm W x 438 mm D x 112 mm H 635 mm W x 438 mm D x 110 mm H not including adjuster not including adjuster Weight Approx 15 0 Ibs 6 8 kg Approx 12 3 Ibs 5 6 kg Only MX CSX1 can be used 18 Finisher specifications Model MX FN12 SPECIFICATIONS Paper sizes 8 1 2 x 14 8 1 2 x 13 1 2 8 1 2 x 13 2 5 8 1 2 x 13 8 1 2 x 11 7 1 4 x 10 1 2 5 1 2 x 8 1 2 envelopes A4 B5 A5 16K Paper weight Thin paper 15 Ibs to 16 Ibs 55 g m to 59 g m2 plain paper 16 Ibs to 28 Ibs 60 g m to 105 g m2 heavy paper 28 Ibs bond to 110 Ibs index 106 g m to 209 g m2 Modes Non sort offset sort staple sort Allowed paper sizes for offset 8 1 2 x 14 8 1 2 x 13 1 2 8 1 2 x 13 2 5 8 1 2 x 13 8 1 2 x 11 7 1 4 x 10 1 2 A4 B5
4. CAUTION Do not install the machine in a location with poor air circulation A small amount of ozone is created inside the machine during printing The amount of ozone created is not sufficient to be harmful however an unpleasant odor may be noticed during large printing runs and thus the machine should be installed in a room with a ventilation fan or windows that provide sufficient air circulation The odor may occasionally cause headaches Install the machine so that people are not directly exposed to exhaust from the machine If installed near a window ensure that the machine is not exposed to direct sunlight The paper will become damp and condensation may form inside the machine causing misfeeds and dirty output t Ambient environment page 16 If the location has an ultrasonic humidifier use pure water in the humidifier If tap water is used minerals and other impurities will be emitted causing impurities to collect on the inside of the machine and create dirty output Exercise care not to expose the paper exit part of the machine to wind or exhaust air The output paper may be blown to the floor Near a wall Be sure to allow the required space around the machine for servicing and proper ventilation The machine should be no closer than the distances indicated below from walls 11 13 16 30cm 11 13 16 17 23 32 30cm 45cm INSTALLATION REQUIREMENTS Dusty locations L
5. 15 SPECIFICATIONS Continuous printing speeds Print ratio 100 Reduced Enlarged 8 1 2 x 11 7 1 2 x 10 1 2 40 pages min A4 B5 16K 38 pages min Print speed during output of the second print and following prints when performing continuous one sided printing of the same page excluding offset output using plain one sided paper from a tray other than the bypass tray Ambient environment Humidity 85 60 20 54 F 86 F 91 F Temperature 10 C 30 C 35 C 16 SPECIFICATIONS Acoustic noise emission measurement according to ISO7779 Sound power level Lwa Printing mode continuous printing 6 8B Standby mode 4 7B Sound pressure level Lpa actual measurement Bystander positions en ge Printing mode Operator positions poet Bystander positions SSB Standby mode Operator positions STOEN Chemical emission measured according to RALUZ122 Edition Jun 2006 Ozone 1 5 mg h or less Dust 4 0 mg h or less Styrene 1 0 mg h or less Benzene less than 0 05 mg h TVOC Printing 10 mg h or less TVOC Pre Operating 1 mg h or less 17 SPECIFICATIONS 500 sheet paper feed unit specifications Model MX CSX1 tray 2 MX CSX2 tray 3 tray 4 Paper sizes 8 1 2 x 14 8 1 2 x 13 1 2 8 1 2 x 13 2 5 8 1 2 x 13 8 1 2 x 11 7 1 4 x 10 1 2 5 1 2 x 8 1 2 A4
6. NG Indicates a risk of death or serious injury AN CAUTION Indicates a risk of human injury or property damage Meaning of the symbols The symbol indicates the need for caution The specific matter that requires AX caution is indicated inside the symbol the symbol at left indicates caution high temperature The symbol indicates an action that is prohibited The specific action that is prohibited is indicated inside or beside the symbol the symbol at left indicates disassembly is prohibited The symbol indicates an action that is mandatory WARNING Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements Also make certain the outlet is properly grounded Do not use an extension cord or adapter to connect other devices to the power outlet used by the machine Using an improper power supply may cause fire or electrical shock For the power supply requirements see the name plate in the lower left corner of the left side of the machine Do not place a container of water or other liquid or a metal object that might fall inside on the machine If the liquid spills or the object falls into the machine fire or electrical shock may result Do not damage or modify the power cord Placing heavy objects on the power cord pulling it or forcibly bending it will damage the cord resulting in fire or electrical shock
7. SHARP MODEL MX B400P LASER PRINTER Safety Guide Please read first Please read this guide first to ensure safe use of the machine Before installing this product be sure to read the TO ENSURE SAFE USE OF THE MACHINE and INSTALLATION REQUIREMENTS sections CAUTIONS INSTALLATION REQUIREMENTS SUPPLIES SPECIFICATIONS TO THE ADMINISTRATOR OF THE MACHINE Keep this manual close at hand for reference whenever needed Each instruction also covers the optional units used with these products Caution For complete electrical disconnection pull out the main plug The socket outlet should be installed near the equipment and should be easily accessible FOR YOUR RECORDS To protect against loss or theft record and retain for reference the machine s serial number located at the lower left corner of the left side of the machine Model Number Serial Number Date of Purchase Place of Purchase Authorized Sharp Dealer Service Department Number Notice for Users in U S A EMC this machine and peripheral devices WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user s authority to operate this equipment Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations NOTE This equipment has been tested and found to comply with the limits
8. ature with minimal temperature fluctuations e not exposed to direct sunlight 2 Store paper in the wrapper and lying flat 3 Paper stored in packages standing up or out of the wrapper may curl or become damp resulting in paper misfeeds Storing toner cartridges Store the box that contains the toner cartridge horizontally do not store it standing up If the toner cartridge is stored standing up the toner may solidify inside the cartridge Store the toner in a location that is cooler than 104 F 40 C Storage in a hot location may cause the toner in the cartridge to solidify Staple cartridge The finisher requires the following staple cartridge MX SCX1 for finisher Approx 5000 per cartridge x 3 cartridges Supply of spare parts and consumables The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of production Spare parts are those parts of the machine which may break down within the scope of the ordinary use of the product whereas those parts which normally exceed the life of the product are not to be considered as spare parts Consumables too are available for 7 years following the termination of production 11 SPECIFICATIONS Machine specifications Name Laser Printer MX B400P Type Desktop Display 4 3 inch color LCD Photoconductive type OPC drum Printing method Electrophotographic system laser Developer syste
9. chine on a surface that can withstand the weight of the machine There is a risk of injury due to the machine falling or toppling If peripheral devices are to be installed do not install on an uneven floor slanted surface or otherwise unstable surface There is a danger of slippage falling and toppling Install the product on a flat stable surface that can withstand the weight of the product Weight when various peripheral devices are installed approx 116 9 Ibs 53 kg O When removing the power plug from the outlet do not pull on the cord Pulling on the cord may cause damage such as wire exposure and breakage and may result in fire or electrical shock Do not touch the transfer belt or the transfer roller Scratches or smudges on the transfer belt or the transfer roller will cause dirty prints Do not block the ventilation ports on the machine Do not install the machine in a location that will block the ventilation ports Blocking the ventilation ports will cause heat to build up in the machine creating a risk of fire Do not throw toner a toner container toner cartridge or a waste toner box into a fire Toner may fly and cause burns Do not install in a location with moisture or dust Risk of fire and electrical shock Store toner toner containers toner cartridges and waste toner boxes out of the reach of children If y
10. conjunction with this Product Your sole remedy in the event that you encounter any difficulties with this Product is against the authorized dealer from which you purchased the Product MX B400P Laser Printer In the event that this authorized dealer does not honor its warranty commitments please contact the General Manager Business Products Group Sharp Electronics Corporation 1 Sharp Plaza Mahwah NJ 07495 1163 so that Sharp can try to help assure complete satisfaction of all the warranty rights to which you are entitled from the authorized dealer 23 TO THE ADMINISTRATOR OF THE MACHINE Trademark acknowledgments The following trademarks and registered trademarks are used in conjunction with the 24 machine and its peripheral devices and accessories e Microsoft Windows Windows 98 Windows Me Windows NT 4 0 Windows 2000 Windows XP Windows Server 2003 Windows Vista Windows Server 2008 Windows 7 and Internet Explorer are registered trademarks or trademarks of Microsoft Corporation in the U S A and other countries e PostScript is a registered trademark of Adobe Systems Incorporated e Adobe and Flash are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and other countries e Adobe the Adobe logo Acrobat the Adobe PDF logo and Reader are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and other countries e Macinto
11. es document image data on the machine s hard drive Stored documents can be called up and printed as needed If a hard drive failure occurs it will no longer be possible to call up the stored document data To prevent the loss of important documents in the unlikely event of a hard drive failure store the original data elsewhere With the exception of instances provided for by law Sharp Corporation bears no responsibility for any damages or loss due to the loss of stored document data BATTERY DISPOSAL THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK UP BATTERY THAT MUST BE DISPOSED OF PROPERLY PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORIZED SERVICE REPRESENTATIVE FOR ASSISTANCE IN DISPOSING OF THIS BATTERY This product utilizes a CR coin Lithium battery which contains a Perchlorate material Special handling for this material may apply California residents See www dtsc ca gov hazardouswaste perchlorate Others consult local environmental officers This product utilizes tin lead solder and fluorescent lamp containing a small amount of mercury Disposal of these materials may be regulated due to environmental consideration For disposal or recycling information please contact your local authorities the Electronics Industries Alliance www eiae org the lamp recycling organization www lamprecycle org or Sharp at 1 800 BE SHARP For U S A Only For North America Non LPS Do not connect to devices other than specif
12. for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This machine contains software modules developed by Independent JPEG Group This product includes Adobe Flash technology of Adobe Systems Incorporated Copyright 1995 2007 Adobe Macromedia Software LLC All rights reserved Contents Storage of supplies 11 Supply of spare parts and consumables 11 SPECIFICATIONS 12 Machine specifications 12 Continuous printing speeds 16 Ambient environment 16 Acoustic noise emission measurement according to ISO7779 eis aiea eee 17 Chemical emission measured according to RALUZ122 Edition Jun 2006 ea eee a 17 500 sheet paper feed unit specifications 18 Finisher specifications 19 TO THE ADMINISTRATOR OF THE MACHINE Factory default passwords 22 Trademark acknowledgments 24 Note e Considerable care has bee
13. ht Plain paper 16 Ibs to 28 Ibs 60 g m to 105 g m2 Paper types SHARP recommended plain paper recycled paper and colored paper Output method Face down output Output capacity 250 sheets using SHARP recommended 8 1 2 x 11 or A4 paper The maximum number of sheets that can be held varies depending on ambient conditions in the installation location the type of paper and the storage conditions of the paper Tray full sensor Yes LAN connectivity 10Base T 100Base TX 1000Base T USB connectivity Type A connector supports USB 2 0 Hi speed Interface port Compatibility requirements of USB 2 0 Memory Capacity Max 32 GB Disk Format FAT32 only Type B connector supports USB 2 0 Hi speed Output tray Center tray Type A connectors are located on the front and back right of the machine two connectors however the connectors cannot be used simultaneously The connector on the back of the machine is not initially available for use If you wish to use the connector contact your service assistance 14 SPECIFICATIONS Machine specifications Continued Required power supply AC 120 V 10 60 Hz Power consumption 1 44 kW Dimensions 22 3 64 W x 17 1 4 D x 24 1 64 H 560 mm W x 438 mm D x 610 mm H Weight Approx 81 6 Ibs 37 kg Overall dimensions 34 11 64 W x 17 1 4 D 868 mm W x 438 mm D when bypass tray is extended
14. ice and may be registered in certain jurisdictions Clarendon Eurostile Helvetica Optima Palatino Stempel Garamond Times and Univers are trademarks of Heidelberger Druckmaschinen AG which may be registered in certain jurisdictions exclusively licensed through Linotype Library GmbH a wholly owned subsidiary of Heidelberger Druckmaschinen AG Apple Chancery Chicago Geneva Monaco and New York are trademarks of Apple Computer Inc and may be registered in certain jurisdictions HGGothicB HGMinchoL HGPGothicB and HGPMinchoL are trademarks of Ricoh Company Ltd and may be registered in some jurisdictions Wingdings is a registered trademark of Microsoft Corporation in the United States and other countries Marigold and Oxford are trademarks of Arthur Baker and may be registered in some jurisdictions Antique Olive is a trademark of Marcel Olive and may be registered in certain jurisdictions Hoefler Text is a trademark of Johnathan Hoefler and may be registered in some jurisdictions ITC is a trademark of International Typeface Corporation registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions Agfa is a trademark of the Agfa Gevaert Group and may be registered in certain jurisdictions Intellifont MicroType and UFST are trademarks of Monotype Imaging Inc registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions Macintosh and TrueType are trademar
15. ied peripheral devices of our company CAUTIONS Laser information Wave length 790 nm 10 nm Pulse times 4 1 us 4 1 ns 7 mm North America and Europe Output power Max 0 6 mW LD1 LD2 Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure This Digital Equipment is CLASS 1 LASER PRODUCT IEC 60825 1 Edition 1 2 2001 For North America SAFETY PRECAUTIONS This Digital Equipment is rated Class 1 and complies with 21 CFR 1040 10 and 1040 11 of the CDRH standards This means that the equipment does not produce hazardous laser radiation For your safety observe the precautions below e Do not remove the cabinet operation panel or any other covers e The equipment s exterior covers contain several safety interlock switches Do not bypass any safety interlock by inserting wedges or other items into switch slots For Europe CLASS 1 LASER PRODUCT LASER KLASSE 1 CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE LASER KLASSE 1 LASER KLASY 1 KLASS 1 LASERAPPARAT INSTALLATION REQUIREMENTS The performance of the machine is affected by the ambient conditions of the installation location Do not install in the following locations Do not install the machine in locations that are excessively hot cold humid or dry near heaters humidifiers air
16. ion an administrator can restrict access to other settings by enabling User accounts The factory default passwords are shown below Factory default account Factory default password User users users Administrator admin admin 22 TO THE ADMINISTRATOR OF THE MACHINE NOTICE for users in the USA BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WARRANTY THAT YOUR SELLING DEALER EXTENDS TO YOU In order to assure you the end user of warranty protection Sharp extends a limited warranty to each of its authorized dealers and in turn requires each of its authorized dealers to extend its own warranty to you on terms that are no less favorable than those given to the dealer by Sharp You should be aware however that Sharp does not itself extend any warranties either express or implied directly to you the end user and no one is authorized to make any representations or warranties on behalf of Sharp Specifically SHARP DOES NOT EXTEND TO YOU THE END USER ANY EXPRESS WARRANTY OR ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR USE OR FITNESS FOR ANY PARTICULAR PURPOSE IN CONNECTION WITH THE HARDWARE SOFTWARE OR FIRMWARE EMBODIED IN OR USED IN CONJUNCTION WITH THIS PRODUCT Sharp is not responsible for any damages or loss either direct incidental or consequential which you the end user may experience as a result of your purchase or use of the hardware software or firmware embodied in or used in
17. ks of Apple Computer Inc registered in the United States Patent and Trademark Office and other countries PostScript is a trademark of Adobe Systems Incorporated and may be registered in some jurisdictions HP PCL FontSmart and LaserJet are trademarks of Hewlett Packard Company and may be registered in some jurisdictions The Type 1 processor resident in Monotype Imaging s UFST product is under license from Electronics For Imaging Inc All other trademarks are the property of their respective owners pn9 s d00v9 XN SHARP SHARP ELECTRONICS CORPORATION 1 Sharp Plaza Mahwah New Jersey 07495 1163 www sharpusa com SHARP ELECTRONICS OF CANADA LTD 335 Britannia Road East Mississauga Ontario L4Z 1W9 SHARP CORPORATION Eel m PRINTED IN CHINA This manual has been printed using a vegetable based 2010A KS1 soy oil ink to help protect the environment TINSE4635FCZZ
18. m Dry type two component magnetic brush development Fusing system Heat rollers Printing resolution 600 x 600 dpi 1200 x 1200 dpi Printing gradation Equivalent to 256 levels Printer driver type PCL5e PCL6 PostScript 3 compatible XPS 2 Supported protocols TCP IP IPX SPX NetBEUI EtherTalk Supported client PC operating systems See VERIFYING SYSTEM REQUIREMENTS in the Software Setup Guide Fonts PCL5e PCL6 80 European fonts 28 barcode fonts s 1 bitmap font PostScript 3 136 European fonts compatible Interface port LAN connectivity 10Base T 100Base TX 1000Base T USB connectivity Supports USB 2 0 Hi speed 4 Memory Standard 512 MB system memory Expansion 1 GB 5 memory Print area Entire page excluding margin of 11 64 4 2 mm at each edge The actual print area may vary depending on the printer driver and the software application 1 When the machine is used as a PostScript printer 2 When the XPS expansion kit is installed 3 Barcode font kit is required 4 Supported operating systems are Windows 2000 Server 2003 XP Vista Server 2008 7 5 To install the XPS expansion kit an expansion memory board is required 12 SPECIFICATIONS Machine specifications Continued Warm up time 1 90 seconds or less First print time 2 8 0 seconds or less Paper sizes 8 1 2 x 14 8 1 2
19. n taken in preparing this manual If you have any comments or concerns about the manual please contact your dealer or nearest SHARP Service Department e This product has undergone strict quality control and inspection procedures In the unlikely event that a defect or other problem is discovered please contact your dealer or nearest SHARP Service Department e Aside from instances provided for by law SHARP is not responsible for failures occurring during the use of the product or its options or failures due to incorrect operation of the product and its options or other failures or for any damage that occurs due to use of the product Warranty While every effort has been made to make this document as accurate and helpful as possible SHARP Corporation makes no warranty of any kind with regard to its content All information included herein is subject to change without notice SHARP is not responsible for any loss or damages direct or indirect arising from or related to the use of this operation manual Copyright SHARP Corporation 2010 All rights reserved Reproduction adaptation or translation without prior written permission is prohibited except as allowed under copyright laws CAUTIONS Symbols in this manual To ensure safe use of the machine this manual uses various safety symbols The safety symbols are classified as explained below Be sure you understand the meaning of the symbols when reading the manual AN WARNI
20. ocations with ammonia gas If dust enters the machine dirty output and Installing the machine next to a diazo copy machine failure may result machine may cause dirty output Locations exposed to direct Locations subject to sunlight vibration Plastic parts may become deformed and Vibration may cause failure dirty output may result The machine includes a built in hard drive Do not subject the machine to shock or vibration In particular never move the machine while the power is on e The machine should be installed near an accessible power outlet for easy connection e Connect the machine to a power outlet which is not used for other electric appliances If a lighting fixture is connected to the same outlet the light may flicker 10 SUPPLIES Standard supplies for this product that can be replaced by the user include paper toner cartridges and staple cartridges for the finisher Be sure to use only SHARP specified products for the toner cartridges finisher staple cartridge and transparency film For best printing results be sure to use only Sharp Genuine lt Supplies which are designed engineered and tested to maximize the life and performance of Sharp products Look for the Genuine Supplies label on the toner package GENUINE SUPPLIES Storage of supplies Proper storage 1 Store the supplies in a location that is e clean and dry e at normal temper
21. of 24 Ibs 90 g m and includes two cover sheets of 28 Ibs bond to 110 Ibs index 106 g m to 209 g m2 Note Special media such as transparency film and label sheets cannot be stapled 20 Contact at Name Administrator Information that the administrator of the machine requires is printed on the back of this page Separate this page from the manual and keep it in a safe place In addition fill in the name of the administrator and the administrator s contact information in the left hand margin 21 TO THE ADMINISTRATOR OF THE MACHINE Separate this page from the manual and keep it in a safe place Factory default passwords When accessing the system settings the administrator password is required to log in with administrator rights The system settings can be configured in the Web pages as well as on the operation panel To access the system settings using the Web pages a password is also required Factory default administrator password Factory default setting admin Store a new administrator password as soon as the machine is installed Once the administrator password has been changed the new password is required to restore the factory default password Take care to remember the new password Factory default passwords Web pages There are two factory default accounts Administrator and User A person who logs in as an Administrator can configure all settings in the Web pages In addit
22. ou find that condensation has formed on the surface of the machine or the display open the right cover and check for condensation inside the machine If condensation has formed inside the machine turn off the main power Turning on the main power when condensation has formed inside the machine may cause a failure Leave the right cover open until the condensation evaporates naturally To keep foreign matter from getting on the primary transfer belt unit or secondary transfer roller unit while the right cover is open place a cover over the opening SOLJO WOOO CAUTIONS A CAUTION The fusing unit is hot When removing a misfeed do not touch the fusing unit Take care not to burn yourself When loading paper removing a misfeed performing maintenance closing the front and side covers and inserting and removing trays take care that your fingers are not pinched If you will not use the machine for a long time be sure to remove the power plug from the outlet for safety When moving the machine switch off the main power and remove the power plug from the outlet before moving The cord may be damaged creating a risk of fire or electrical shock The machine is heavy To prevent injury when moving the machine it is recommended that it be moved by two or more persons CAUTIONS The machine includes the print hold function which stor
23. sh Mac OS AppleTalk EtherTalk and LaserWriter are trademarks of Apple Inc registered in the U S and other countries e Netscape Navigator is a trademark of Netscape Communications Corporation e Mozilla and Firefox are registered trademarks or trademarks of the Mozilla Foundation in the U S A and other countries e PCL is a registered trademark of the Hewlett Packard Company e IBM PC AT and PowerPC are trademarks of International Business Machines Corporation e Sharpdesk is a trademark of Sharp Corporation e Sharp OSA is a trademark of Sharp Corporation e RealVNC is a trademark of RealVNC Limited e All other trademarks and copyrights are the property of their respective owners Candid and Taffy are trademarks of Monotype Imaging Inc registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions CG Omega CG Times Garamond Antiqua Garamond Halbfett Garamond Kursiv Garamond and Halbfett Kursiv are trademarks of Monotype Imaging Inc and may be registered in certain jurisdictions Albertus Arial Coronet Gill Sans Joanna and Times New Roman are trademarks of The Monotype Corporation registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions Avant Garde ITC Bookman Lubalin Graph Mona Lisa Zapf Chancery and Zapf Dingbats are trademarks of International Typeface Corporation registered in the United States Patent and Trademark Off
24. x 13 1 2 8 1 2 x 13 2 5 8 1 2 x 13 8 1 2 x 11 7 1 4 x 10 1 2 5 1 2 x 8 1 2 A4 B5 A5 16K Includes automatic paper size detection function Paper weight Plain paper 16 Ibs to 28 Ibs 60 g m2 to 105 g m2 Paper capacity Plain paper 21 Ibs 80 g m2 500 sheets Paper types SHARP recommended plain paper recycled paper and colored paper Bypass tray Paper sizes 8 1 2 x 14 8 1 2 x 13 1 2 8 1 2 x 13 2 5 8 1 2 x 13 8 1 2 x 11 7 1 4 x 10 1 2 5 1 2 x 8 1 2 envelopes A4 B5 A5 16K Includes automatic paper size detection function Paper sizes from 3 15 16 x 5 53 64 100 mm x 148 mm to 8 33 64 x 14 1 64 216 mm x 356 mm can be entered Paper weights Thin paper 15 Ibs to 16 Ibs 55 g m to 59 g m plain paper 16 Ibs to 28 Ibs 60 g m to 105 g m2 heavy paper 28 Ibs bond to 110 Ibs index 106 g m to 209 g m2 Paper capacity Standard paper 100 sheets Paper types SHARP recommended plain paper recycled paper colored paper heavy paper thin paper transparency film and envelopes Monarch Com 10 DL C5 1 Warm up time may vary depending on some environments 2 First print time may vary depending on the status of the machine 13 SPECIFICATIONS Machine specifications Continued Paper sizes 8 1 2 x 14 8 1 2 x 13 1 2 8 1 2 x 13 2 5 8 1 2 x 13 8 1 2 x 11 5 1 2 x 8 1 2 A4 B5 A5 16K Duplex module Paper weig
Download Pdf Manuals
Related Search