Shark UV410 User's Manual
Contents
1. dryer or other heating methods to dry 6 Insert the foam filter into the top of the filter frame When replacing the felt filter make sure that the felt part of the filter is facing out 7 Replace the filter frame into the motor base and then replace the dust cup UV410_26_IB_ENG_120229 5 indd 9 A IMPORTANT Loss of Suction may occur if filters are not cleaned every 3 months Rinse and allow to air dry completely Tap loose dirt from foam filter as needed in between washing Filters may appear dirty after use this is normal To clean the post motor filter 4 Remove the filter cover from the front of the vacuum by pulling up on the tab and pulling the cover away from the vacuum 2 Take out the filter by pulling it straight out 3 Wash the filter under the tap using lukewarm water with the dirty side face down until the water runs clear Apo not put the filter in the washing machine or dishwasher 4 Allow the filter to air dry for 24 hours Do not use a hair dryer or other heating methods to dry 5 Once the filter is dry replace it back into the vacuum 6 Replace the cover by inserting the two tabs into the holes at the bottom and then swinging the cover up until it clicks into place www sharkclean com 9 12 02 29 1 30 PM Troubleshooting WARNING E Vacuum is not picking up dirt To reduce the risk of electric shock the power cord must be disconnected before performing mai PROBLEM POSSIBL2. Attach the Super Stretch Hose a Snap hose into swivel connector b Route under anti tip hook c Route over upper hose holder d Press securely onto cleaning wand IMPORTANT To prevent vacuum from tipping secure hose under the anti tip hose hook UV410_26_IB_ENG_120229 5 indd 5 9 To store the vacuum When storing your vacuum wind the cord around the two cord holders and secure with cord clip e Quick Cord release at the top of the unit place in the upright position e Cord holder near the base turn it until it is pointing down To release the cord turn the Quick Cord release to the left or right Store the Extended Reach Kit the Pet Hair Power Brush and the 24 Crevice Tool with the vacuum when not in use IMPORTANT For suction to reach the Floor Power Nozzle the Cleaning Wand and Super Stretch Hose must be attached securely on the vacuum body 10 To carry the vacuum With the unit in the standing position lift by the Dust Cup Handle CAUTION When lifting or carrying DO NOT press Dust Cup Assembly release button www sharkclean com 5 12 02 29 1 30 PM Using the Vacuum A IMPORTANT To protect your carpets the brushroll will only turn on when you have pulled the handle back towards you and released the Floor Power Nozzle Power Switch Settings OFF Bare Floors Tools Carpets Your Shark Navigator Upright 4 Vacuum can be used t
3. E REASONS amp SOLUTIONS ntenance troubleshooting checks Check filters to see if they need cleaning Follow instructions for rinsing and drying the filters before re inserting back into the vacuum See Maintenance sections for instructions Dust cup may be full empty dust cup Check hose and hose connections for blockages clear blockages if required If dust cup is empty and attachment inlets are clear check for other blockages See Checking for Blockages for instructions Vacuum lifts scatter rugs lightweight movable rugs Suction is powerful Take care when vacuuming scatter type rugs or rugs with delicately sewn edges Open the suction release on the hose to decrease suction power Airflow is restricted No suction or light suction Check filters to see if they need cleaning Follow instructions for rinsing and drying the filters before re inserting back into the vacuum See Maintenance sections for instructions Dust cup may be full empty dust cup Check hose hose connections nozzles and accessories for blockages clear blockages if required Close the suction release on the hose to increase suction power If dust cup is empty and attachment inlets are clear check for other blockages See Checking for Blockages for instructions Motorized floor brush has become jammed or has shut off Immediately turn off and unplug vacuum disconnect the nozzle and remove bloc
4. For best results empty the Dust Cup after each use empty several times during prolonged usage or when it reaches the MAX fill line NEVER OVER FILL THE DUST CUP Stand vacuum into upright position Turn vacuum off To empty the Dust Cup 1 Grip carry handle and press the Dust Cup release button to remove 2 Option A For Quick Empty Insert Dust Cup deep inside trash receptacle to contain dust and debris Press the bottom Dust Cup release button tap container gently to dislodge and release dust and debris Snap door in place Aj Important If the Dust Cup Door does not swing open after pressing the release button push the door open using the bottom door tabs Option B For Allergy Sufferers Wrap a trash bag around the Dust Cup leaving space at the bottom for the door to swing open Locate the Dust Cup Door release button within the trash bag and press to release as you shake the dust cup to empty dust and debris Snap the bottom door in place Note Option B can also be performed outside of the home to further minimize releasing dust back into the air Carry just the Dust Cup and trash bag outside s S R ToL FREE 1 800 798 7398 UV410_26_IB_ENG_120229 5 indd 8 CAUTION Unplug the vacuum failure to do so might result in electric shock AX Note Some dust and debris may remain in the top of your dust cup on or near the metal screen It is not necessary
5. Shark UV410 Owner s Guide www sharkclean com UV410_26_IB_ENG_120229_5 indd 1 12 02 29 1 30 PM This manual covers model numbers UV410 26 TECHNICAL SPECIFICATIONS Voltage 120V Watts 1200W Amps 10A Hertz 60Hz ER TOLL FREE 1 800 798 7398 UV410_26_IB_ENG_120229 5 indd 2 12 02 29 1 30 PM Thank you for purchasing the Shark Navigator Upright Vacuum UV410_26_IB_ENG_120229 5 indd 1 Contents Important Safety Instructions 2 Getting Started 4 Using the Vacuum 6 Cleaning with the Vacuum Accessories 7 Emptying the Dust Cup Assembly 8 Proper Care of Your Vacuum 9 Troubleshooting 10 Checking for Blockages 11 Maintenance 12 Warranty and Registration 13 www sharkclean com 1 12 02 29 1 30 PM IMPORTANT SAFETY INSTRUCTIONS For Household Use Only WARNING TO REDUCE THE RISK OF FIRE ELECTRIC WHEN USING YOUR SHARK NAVIGATOR SHOCK OR INJURY UPRIGHT VACUUM BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE GENERAL ELECTRICAL SAFETY FOLLOWED INCLUDING THE FOLLOWING 1 Unplug from electrical outlet when not in use and before servicing READ ALL INSTRUCTIONS BEFORE USING 2 DO NOT use vacuum with a damaged cord or YOUR SHARK NAVIGATOR UPRIGHT plug VACUUM DO NOT pull or carry vacuum by the cord POLARIZED PLUG 4 DO NOT unplug by pulling on cord to unplug This appliance has a polarized plug one blade grasp the plug not the cord is wider than the other As a sa
6. accompanying instructions www sharkclean com 13 UV410_26_IB_ENG_120229 5 indd 13 12 02 29 1 30 PM Euro Pro Operating LLC USA Newton MA 02459 CAN 4400 Bois Franc St Laurent QC H4S 1A7 English 1 800 798 7398 www sharkclean com Copyright Euro Pro Operating LLC 2012 Printed in China Illustrations may differ from actual product UV410 E 120229 5 UV410_26_IB_ENG_120229 5 indd 14 12 02 29 1 30 PM
7. fety feature this 5 DO NOT handle plug or vacuum cleaner with plug will fit into a polarized outlet only one way wet hands Do not force into the outlet or try to 6 DO NOT run the vacuum over the power cord modify the plug to fit 7 DO NOT close a door on the cord 8 DO NOT pull cord around sharp corners 9 DO NOT leave appliance when plugged in 10 Keep power cord away from heated surfaces 11 Turn off all controls before plugging or unplugging vacuum cleaner 12 Always turn off this appliance before connecting or disconnecting the motorized nozzle AWARNING HOSE ATTACHMENTS 13 DO NOT use if air flow is restricted if the air TO REDUCE THE RISK OF ELECTRIC paths the hose or the extension tube become SHOCK OR INJURY DO NOT USE blocked turn the vacuum cleaner off Remove OUTDOORS OR ON WET SURFACES all obstructions before you turn on the unit again 14 Keep the end of the hose wands and other openings away from face and body 15 Keep rotating brush and suction openings away from hair face fingers uncovered feet or loose clothing 16 Only use manufacturer s recommended attachments 2 S R TOLL Free 1 800 798 7398 UV410_26_IB_ENG_120229 5 indd 2 12 02 29 1 30 PM GENERAL USE 17 18 19 20 21 Dd 23 Use only as described in this manual DO NOT put any objects into openings Keep your work area well lit Keep the vacuum moving over the carpet surface at all time
8. ice support call 1 800 798 7398 or visit www sharkclean com e Canada EURO PRO Operating LLC 4400 Bois Franc St Laurent Qu bec H4S 1A7 If the appliance is found to be defective in material or workmanship EURO PRO Operating LLC will repair or replace it free of charge Proof of purchase date and 16 99 to cover the cost of return shipping and handling must be included Non durable parts including without limitation filters brushes and electrical parts which normally require replacement are specifically excluded from warranty The liability of EURO PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes This limited warranty does not cover damage caused by misuse abuse negligent handling or damage due to faulty packaging or mishandling in transit This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs service or alterations to the product or any of its parts which have been performed by a repair person not authorized by EURO PRO Operating LLC This warranty is extended to the original purchaser of the unit and excludes all other legal and or conventional warranties The responsibility of EURO PRO Operating LLC if any is limited to the specific obligations expressly assumed by it under the terms of
9. kage before reconnecting and turning vacuum back on See Checking for Blockages for instructions Vacuum turns off on its own This vacuum cleaner is equipped with a motor protective thermostat If for some reason your vacuum overheats the thermostat will automatically turn the unit off Should this occur perform the following steps to restart the motor thermostat 1 Move the On Off switch to the O Off position 2 Unplug the vacuum 3 Empty the dust cup and clean filters See Maintenance sections for instructions 4 Check for blockages in hose accessories and inlet openings See Checking for Blockages for instructions 5 Allow the unit to cool for a minimum of 45 minutes 6 Plug in the vacuum 7 Turn the On Off switch to the I On position to restart the vacuum Note If vacuum still does not start contact Customer Service at 1 800 798 7398 10 i Toit Free 1 800 798 7398 UV410_26_IB_ENG_120229_ 5 indd 10 12 02 29 1 30 PM Checking for Blockages Blockages may cause your vacuum to overheat and shut down If so clear the blockages then follow the instructions for Resetting the Motor Thermostat on page 12 WARNING Never insert sharp objects into any opening to clear an obstruction IMPORTANT Damages caused while clearing or attempting to clear blockages are not covered under your product s limited warranty Unplug the vacuum befo
10. ng for Blockages on page 11 Wait 45 minutes for vacuum to cool then plug in the vacuum Turn the Power Switch to the I On position to start the vacuum Note If vacuum still does not start contact Customer Service at 1 800 798 7398 12 gt TOLL FREE 1 800 798 7398 UV410_26_IB_ENG_120229 5 indd 12 1 Cleaning the Pet Hair Power Brush Slide locking latch A forward Gently tilt brush housing upward to open IMPORTANT DO NOT force it will not open all the way Remove debris from turbine wheel and air passage Ordering Replacement Parts To order additional parts and accessories go to www sharkclean com or call 1 800 798 7398 PART PART NO Super Stretch Hose 1114 FC Dusting Brush amp Crevice Tool 1115 FC Foam amp Felt Filters XFF36 Turbo Brush 137FFJ Cleaning Wand 1116 FC 24 Crevice Tool 1124 FC 12 02 29 1 30 PM Euro Pro Five Year 5 Limited Warranty EURO PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of five 5 years from the date of the original purchase when utilized for normal household use subject to the following conditions exclusions and exceptions If your appliance fails to operate properly while in use under normal household conditions within the warranty period return the complete appliance and accessories freight prepaid to e U S EURO PRO Operating LLC For customer serv
11. o clean bare floors or carpets with the click of a switch Stand the vacuum into the upright position Plug in the vacuum 4 Start with the Power Switch in the O Off position 2 Place your foot on the Floor Power Nozzle and pull handle 5 towards you 3 Set the Power Switch to desired cleaning setting When cleaning carpets Ensure you have pulled the handle towards you and select the II Brushroll On position to agitate the carpet fibers for deeper cleaning performance When cleaning bare floors Select the I On position for suction only cleaning to avoid scattering dirt while cleaning Due to the huge suction power of this vacuum it may become necessary to adjust the suction release on the hose If the vacuum is difficult to push or pull or if it is lifting up area rugs adjust the suction release by opening or closing the valve at the top end of the hose 6 a Toit Free 1 800 798 7398 UV410_26_IB_ENG_120229 5 indd 6 C Release suction for easier push and pull on high pile carpets and area rugs AX IMPORTANT Your Brushroll Indicator Light will illuminate solid green when the brushroll is on or solid red if there is a blockage This feature is designed to protect your Lifetime Belt that powers your brushroll See Checking for Blockages on page 11 AQ NOTE The height of your power nozzle has been optimized for easy pushing and superior cleaning on all floor t
12. r other explosive or toxic materials DO NOT vacuum up any liquids DO NOT immerse vacuum cleaner in water or other liquids DO NOT use outdoors or on wet surfaces use only on dry surfaces Use extra care when cleaning on stairs SAVE THESE INSTRUCTIONS www sharkclean com 3 12 02 29 1 30 PM Getting Started FIRST THING S FIRST YOU NEED TO KNOW WHAT S IN THE BOX YOU JUST OPENED Vacuum Body Floor Power Nozzle Handle Assembly Super Stretch Hose Cleaning Wand Pet Hair Power Brush Cleaning Attachments 24 Crevice Tool Extended Reach Kit ZaA7T7AmMOARD Note Optional tools are available for sale for any UV410 model 1 800 798 7398 Your Shark Navigator Upright is easy to assemble 1 Lay your vacuum body on a level surface 2 Slide the electrical connection from the power nozzle into the main body to click into place 3 Connect the hose from the main body to the power nozzle push with a slight turning motion to create a snug fit 4 Slide the handle assembly into the upright unit aligning the hose hook on the handle assembly with the power cord hooks on the back of the unit 5 Secure the handle assembly in place with included nut bolt shipped attached to handle assembly 6 Place the vacuum in the upright position 7 Store the Crevice Tool Dusting Brush and Cleaning Wand on the unit UV410_26_IB_ENG_120229 5 indd 4 12 02 29 1 30 PM 8
13. re checking for blockages Reassemble all parts securely before a operating vacuum _ 1 Dust Cup Air Duct 3 Floor Power Nozzle Hose Stand vacuum into upright Connector position Lay vacuum flat Remove Dust Cup Assembly and Remove Nozzle Hose and check empty Dust Cup if necessary for clogs Disconnect the Super Stretch Push the Hose Connector back Hose onto the Floor Power Nozzle Check Air Duct behind Dust Cup 4 Hose for clogs clear before replacing Stand vacuum upright Dust Cup Assembly j Remove hose from both the unit 2 Intake Opening behind the and Cleaning Wand ends Brushroll Inspect both ends and the length Lay the vacuum flat to expose of the hose for clogs brushroll R es kaii turn ti tot t Check opening behind the E E ere brushroll for clogs Clear the opening Clear the brushroll use scissors to carefully cut away threads hair or other debris that might be trapped in the bristles www sharkclean com 11 UV410_26_IB_ENG_120229 5 indd 11 12 02 29 1 30 PM Maintenance Resetting the Motor Thermostat Your Shark Navigator Upright Vacuum is equipped with a protective Motor Thermostat If the motor should overheat the thermostat shuts off the power To reset the Motor Thermostat Move the Power Button to the O Off position Unplug the vacuum Check for clogged hose or filter unclog hose and replace filter Refer to Checki
14. s to avoid damaging the carpet fibers DO NOT place vacuum on unstable surfaces such as chairs or tables DO NOT allow young children to operate the vacuum or use as a toy DO NOT use vacuum cleaner if it has been dropped damaged left outdoors or submerged in water Return to EURO PRO Operating LLC for examination repair or adjustment CYCLONIC CHAMBER DUST CUP FILTERS 24 Before turning on the vacuum e Make sure that dust cup cyclonic chamber and all filters are in place after routine maintenance e Make sure that all components and filters are thoroughly dry after routine cleaning e Only use filters and accessories provided by EURO PRO Operating LLC Failure to do so will void the warranty UV410_26_IB_ENG_120229 5 indd 3 GENERAL CLEANING 25 26 27 28 29 30 31 32 33 34 DO NOT run the vacuum over large sized objects DO NOT pick up hard or sharp objects such as glass nails screws or coins that could damage the vacuum cleaner DO NOT pick up smoking or burning objects such as hot coals cigarette butts or matches DO NOT pick up flammable or combustible materials such as lighter fluid gasoline kerosene or use in areas where they may be present DO NOT pick up toxic solutions such as chlorine bleach ammonia or drain cleaner DO NOT use in an enclosed space where vapors are present from paint paint thinner moth proofing substances flammable dust o
15. the limited warranty In no event is EURO PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever Some states do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province IMPORTANT Carefully pack item to avoid damage in shipping Be sure to include proof of purchase date and to attach tag to item before packing with your name complete address and phone number with a note giving purchase information model number and what you believe is the problem with item We recommend you insure the package as damage in shipping is not covered by your warranty Mark the outside of your package ATTENTION CUSTOMER SERVICE We are constantly striving to improve our products therefore the specifications contained herein are subject to change without notice Product Registration Please visit www sharkclean com or call 1 800 798 7398 to register your new Shark product within ten 10 days of purchase You will be asked to provide the store name date of purchase and model number along with your name and address The registration will enable us to contact you in the unlikely event of a product safety notification By registering you acknowledge to have read and understood the instructions for use and warnings set forth in the
16. to completely remove this material before continuing to vacuum Shark advanced cyclonic action will sweep the metal screen clean once you begin to refill your dust cup 12 02 29 1 30 PM Proper Care of Your Vacuum COMPONENT MAINTENANCE SCHEDULE 1 Dust Cup Empty each time you vacuum 2 Pre Motor Foam Filter Rinse and air dry every 3 months under normal use 3 Pre Motor Felt Filter Rinse and air dry every 3 months under normal use 4 Post Motor Filter Clean once every 12 months under normal use NOTE The material in the filters will discolor over time This is NORMAL and will not affect the performance of the filters Addo not operate the vacuum without ALL the filters in place Ado NOT operate the vacuum with WET filters Pre Motor Pre Motor Foam Filter Felt Filter Felt Side Up v A Filter Frame Underside Filter Frame Post Motor Filter To clean the pre motor filters 1 Remove the dust cup 2 Lift the filter frame out from the top of the motor base Remove the foam filter from inside the filter frame 3 Turn the filter frame upside down and carefully pull the felt filter out 4 Rinse the filters thoroughly in lukewarm water until the water runs clear as per the maintenance schedule above A donot put the filters in the washing machine or dishwasher 5 Squeeze out excess water and let air dry for at least 24 hours before replacing Do not use a hair
17. ypes so there is no need to make any height adjustments as you transition to different floor amp carpet types 12 02 29 1 30 PM Cleaning with the Vacuum Accessories Extended Reach Cleaning Kit a 4 2 Using the Cleaning Wand Stand the vacuum into upright position Remove the Cleaning Wand with hose attached from the E unit Vacuum Accessories Push the selected tool into the Before cleaning with your Your vacuum comes with a Super accessories Stretch Hose and Cleaning Wand end of the Cleaning Wand sas Use one or the other to attach your 3 Pet Hair Power Brush Stand vacuum into upright position A cleaning accessories 4 Dusting Brush Secure Super Stretch Hose in 1 Using the Super Stretch Hose 5 Crevice Tool the anti tip hose Stand the vacuum into upright 6 24 Crevice Tool hook to prevent position Extended Reach Cleaning Kit tipping Remove the hose from the Includes an extra Cleaning Wand and Select the I On position for Cleaning Wand extra Super Stretch Hose suction only cleaning Push the selected tool into the Increases your cleaning DO NOT pull vacuum cleaner hose connector reach to over 27 feet around by the hose To order additional parts and accessories Apo NOT overextend the hose go to wwwsharkclean com or call 1 800 798 7398 www sharkclean com 7 UV410_26_IB_ENG_120229 5 indd 7 12 02 29 1 30 PM Emptying the Dust Cup Assembly
Download Pdf Manuals
Related Search