Shark NV100 User's Manual
Contents
1. ADDITIONAL ACCESSORIES CREVICE TOOL D amp Reach deep into narrow spaces and clean between cushions under radiators and baseboards and in hard to reach crevices and corners MULTI TOOL This unique tool combines a dusting brush and a crevice tool into one PET UPHOLSTERY TOOL This tool will remove hair from upholstery and stairs NOTE Some accessories may be included with your purchase To order Additional Parts amp Accessories go to www sharkclean com PART PART NO Stretch Hose 126FF Multi Tool 127FFJ Foam amp Felt Filter XFL100 Extension Wand 1116 FC 24 Crevice Tool 122FFJ 11 Crevice Tool 129FFJ Pet Upholstery Tool 128FFJ www sharkclean com 11 11 03 17 10 40 AM Notes Euro Pro Three Year 3 Limited Warranty EURO PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of three 3 years from the date of the original purchase when utilized for normal household use subject to the following conditions exclusions and exceptions If your appliance fails to operate properly while in use under normal household conditions within the warranty period return the complete appliance and accessories freight prepaid to e U S EURO PRO Operating LLC For customer service support call 1 800 798 7398 or visit www sharkclean com e Canada EURO PRO Operating LLC 4400 Bois Franc St Laurent Qu bec H4S 1A7 If the appliance2. and pull out To replace align the pins into the hinges b on the vacuum Rotate it fully to secure Fig 5 When storing your vacuum wind the power cord around the two cord holders and secure with cord clip Fig 6 There is a Quick Cord Release on the top cord holder Simply turn to the left or right to release the power cord To store the unit the cord holder should be in the upright position IMPORTANT For suction to reach the motorized floor brush the extension wand and stretch hose must be attached securely on the vacuum body Not all accessories are available on all models 8 TO CARRY THE VACUUM With the unit in the standing position lift by the Dust Cup Handle carry handle CAUTION When lifting or carrying DO NOT press Dust Cup release button www sharkclean com 5 11 03 17 10 40 AM Using the Vacuum AX for suction to reach the power nozzle the extension wand and stretch hose must be attached securely on the vacuum body Your Shark Navigator can be used to clean all surface types 4 Plug in the vacuum 2 Push the Power button Fig 7 3 Place your foot on the power nozzle and pull the handle back towards you Fig 8 NOTE This vacuum has a separate brushroll button ss on the top of the vacuum Fig 9 4 CLEAN CARPETS Engage the brushroll by pushing the brushroll button ess to the ON position The brushroll light
3. filters before re inserting back into the vacuum See Maintenance sections for instructions Dust cup may be full empty dust cup Check hose and hose connections for blockages clear blockages if required If dust cup is empty and attachment inlets are clear check for other blockages See Checking for Blockages for instructions Airflow is restricted No suction or light suction Check filters to see if they need cleaning Follow instructions for rinsing and drying the filters before re inserting back into the vacuum See Maintenance sections for instructions Dust cup may be full empty dust cup Check hose hose connections nozzles and accessories for blockages clear blockages if required If dust cup is empty and attachment inlets are clear check for other blockages See Checking for Blockages for instructions Bush roll does not turn on Press the brushroll button to the ON position The brushroll light near this button will illuminate green when ON Place your foot on the floor brush and pull the handle back to engage the brushroll If the red light on the power nozzle is illuminated see the section on Checking for Blockages Vacuum turns off on its own This vacuum cleaner is equipped with a motor protective thermostat If for some reason your vacuum overheats the thermostat will automatically turn the unit off Should this occur perform the
4. is found to be defective in material or workmanship EURO PRO Operating LLC will repair or replace it free of charge Proof of purchase date and 16 99 to cover the cost of return shipping and handling must be included Non durable parts including without limitation filters brushes and electrical parts which normally require replacement are specifically excluded from warranty The liability of EURO PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes This limited warranty does not cover damage caused by misuse abuse negligent handling or damage due to faulty packaging or mishandling in transit This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs service or alterations to the product or any of its parts which have been performed by a repair person not authorized by EURO PRO Operating LLC This warranty is extended to the original purchaser of the unit and excludes all other legal and or conventional warranties The responsibility of EURO PRO Operating LLC if any is limited to the specific obligations expressly assumed by it under the terms of the limited warranty In no event is EJRO PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever Some
5. will turn green Fig 9 NV100_26_IB_ENG_110317_2 indd 6 7 6 ER TOLL FREE 1 800 798 7398 Ay DO NOT pull vacuum cleaner around by the hose DO NOT over extend the hose Always hold the vacuum so that it does not tip A MPORTANT To protect your carpets the brushroll will only turn on when you have pulled the handle back towards you and released the power nozzle j MPORTANT The brushroll indicator light on the power nozzle will illuminate solid red if there is a blockage Fig 10 This feature is designed to protect your Lifetime Belt that powers your brushroll See Checking for Blockages on page 11 5 CLEAN BARE FLOORS For cleaning bare floors or to clean with the hose push the brushroll button s to the OFF position for suction only The brushroll light will turn off The brushroll will not spin in this mode over gre height of your power nozzle has been optimized for easy pushing and superior cleaning on all floor types There is no need to make any height adjustments as you transition to different floor amp carpet types Fig 12 6 CLEAN ABOVE FLOORS WITH HOSE You can attach the accessories onto the handle or onto the extension wand for a longer reach a Stand the vacuum into upright position b To remove the handle only press the handle release button Fig 11 c To remove the handle with the extension wand press the extension wand release button on the back
6. OT pull or carry vacuum by the cord DO NOT unplug by pulling on cord to unplug grasp the plug not the cord DO NOT handle plug or vacuum cleaner with wet hands DO NOT run the vacuum over the power cord DO NOT close a door on the cord DO NOT pull cord around sharp edges or corners DO NOT leave appliance when plugged in Keep power cord away from heated surfaces Turn off all controls before plugging or unplugging vacuum cleaner GENERAL USE Use only as described in this manual DO NOT put any objects into openings Keep your work area well lit Keep the vacuum moving over the carpet surface at all times to avoid damaging the carpet fibers DO NOT place vacuum on unstable surfaces such as chairs or tables DO NOT allow young children to operate the vacuum or use as a toy Close attention is necessary when used by or near children DO NOT use vacuum cleaner if the appliance is not working as it should has a damaged plug or cord if the unit has been dropped damaged left outdoors or submerged in water Return to EURO PRO Operating LLC for examination repair or adjustment GENERAL CLEANING 20 21 22 23 24 25 26 21 28 29 30 DO NOT run the vacuum over large sized objects DO NOT pick up hard or sharp objects such as glass nails screws or coins that could damage the vacuum cleaner DO NOT pick up smoking or burning objects
7. Shark NWA Re le Owner s Guide NV100_26_IB_ENG_110317_2 indd 1 11 03 17 10 40 AM This manual covers model NV100 26 TECHNICAL SPECIFICATIONS Voltage 120V Watts 700W Amps 5 83A Hertz 60Hz ER TOLL FREE 1 800 798 7398 NV100_26_IB_ENG_110317_2 indd 2 1 Thank you for purchasing the Shark Navigator Vacuum Contents Important Safety Instructions Getting Started Assembly Using the Vacuum Emptying the Dust Cup Assembly Proper Care of Your Vacuum Troubleshooting Checking for Blockages Maintenance Warranty and Registration www sharkclean com 1 11 03 17 10 40 AM IMPORTANT SAFETY INSTRUCTIONS For Household Use Only WHEN USING YOUR SHARK NAVIGATOR VACUUM BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK NAVIGATOR VACUUM POLARIZED PLUG This appliance has a polarized plug one blade is wider than the other As a safety feature this plug will fit into a polarized outlet only one way Do not force into the outlet or try to modify the plug to fit A WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY DO NOT USE OUTDOORS OR ON WET SURFACES 2 ER TOLL FREE 1 800 798 7398 NV100_26_IB_ENG_110317_2 indd 2 3 GENERAL ELECTRICAL SAFETY 1 Unplug from electrical outlet when not in use and before servicing DO NOT use vacuum with a damaged cord or plug DO N
8. _110317_2 indd 12 13 11 03 17 10 40 AM Euro Pro Operating LLC Newton MA 02459 English 1 800 798 7398 www sharkclean com Copyright Euro Pro Operating LLC 2011 Printed in China Illustrations may differ from actual product NV100 26 E 110317 2 NV100_26_IB_ENG_110317_2 indd 14 11 03 17 10 40 AM
9. following steps to restart the motor thermostat 1 Press the power button to the Off position 2 Unplug the vacuum 3 Empty the dust cup and clean filters See Maintenance sections for instructions 4 Check for blockages in hose accessories and inlet openings See Checking for Blockages for instructions 5 Allow the unit to cool for a minimum of 45 minutes 6 Plug in the vacuum 7 Press the power button to the On position to restart the vacuum Note If vacuum still does not start contact Customer Service at 1 800 798 7398 To purchase replacement parts please visit our website www sharkclean com www sharkclean com 9 11 03 17 10 40 AM Checking for Blockages Blockages may cause your vacuum to overhea this occurs and shut down If clear the blockages then follow the instructions for Resetting on page 11 IMPORTANT Never insert sharp objects an obs while cl clear b under your product s limited the Motor Thermostat into any opening to clear ruction Damages caused learing or attempting to ockages are not covered warran Reassemble all parts securely before operating vacuum 10 ER TOLL FREE 1 800 798 7398 Unplug the vacuum before checking for blockages 3 HOSE Disconnect the Stretch Hose by gently pressing the tabs together and pulling away from the hose connector 1 DUST CUP AIR DUCT Stand vac
10. ion B can also be performed outside of the home to further minimize releasing dust back into the air Carry just the Dust Cup Assembly and trash bag outside A Note It may become necessary to occasionally clean the metal screen inside the dust cup To clean press the top dust cup release button Fig 17 pull out the metal screen and remove any excess dirt Then replace the metal screeen inside the dust cup and close the top lid Fig 18 www sharkclean com 7 11 03 17 10 40 AM Proper Care of Your Shark Upright Vacuum COMPONENT MAINTENANCE SCHEDULE 1 Dust Cup Empty each time you vacuum 2 Pre Motor Foam Filter Rinse and air dry every 3 months under normal use 3 Pre Motor Felt Filter Rinse and air dry every 3 months under normal use 4 Post Motor Filter Clean once every 12 months under normal use Apo not put the filters in the washing machine or dishwasher NOTE The material in the filter will discolor over time This is NORMAL and will not affect the performance of the filter CAUTION Unplug the vacuum while cleaning filters failure to do so might result in electric shock Pre Motor Foam Filter Felt Filter Post Motor Filter Fig 18 CLEANING THE PRE MOTOR FILTERS 1 Remove the dust cup 2 Pull the 2 filters out from the top of the motor base Fig 18 3 Rinse the filters thoroughly in lukewarm water until the water runs clear 4 Squeeze out excess
11. ion openings away from hair face fingers uncovered feet or loose clothing Only use manufacturer s recommended attachments SAVE THESE INSTRUCTIONS www sharkclean com 3 11 03 17 10 40 AM Getting Started FIRST THING S FIRST YOU NEED TO KNOW WHAT S IN THE BOX YOU JUST OPENED a Handle b Extension Wand e Hose Connector f Vacuum Body Stretch Hose g Accessory Holder Dust Cup h Power Nozzle Optional tools are available for sale for any NV100 model To order additional parts or accessories go to www sharkclean com a S R tors FREE 1 800 798 7398 NV100_26_IB_ENG_110317_2 indd 4 5 ASSEMBLY 1 YOUR SHARK NAVIGATOR IS EASY TO ASSEMBLE Place your vacuum body upright ona level surface Insert the hose connector into the opening on the back of the vacuum body Fig 1 NOTE Once the hose connector has been inserted it cannot be removed Insert the handle with the extension wand into the top of the vacuum until secure Fig 2 Fig 4 Insert the stretch hose into the hose connector on the back of the unit Make sure that it snaps in place Fig 3 Store your on board tools onto the accessory holder located on the back of the unit Fig 4 NOTE The accessory holder is removable In order to remove or attach the accessory holder you must remove the dust cup first To remove the accessory holder just hold the tab a rotate left
12. of the vacuum Fig 12 d Push the selected tool into the end of the handle or handle with extension wand for longer reach and begin cleaning To order additional parts and accessories go to wwwsharkclean com Emptying the Dust Cup Assembly pea best results empty the Dust Cup Assembly after 2 each use or as needed during prolonged usage or when it reaches the MAX fill line DO NOT OVERFILL Turn vacuum off before emptying Dust cup Release TO EMPTY THE DUST CUP ASSEMBLY 4 Press the Dust Cup release button and remove the dust cup from the vacuum Fig 13 2 Grip carry handle and press the bottom Dust Cup Door release button Fig 14 3 Option A for Quick Empty Insert Dust Cup Assembly deep inside trash receptacle to contain dust and debris Fig 15 Press the bottom Dust Cup Door release button tap container gently to dislodge and release dust and debris Close the bottom door until it snaps in place Ai important If the Dust Cup Door does not swing open freely after pressing the release button push the door open using the bottom door tabs 4 Option B For Allergy Sufferers Wrap a trash bag around the Dust Cup Assembly leaving space at the bottom for the door to swing open Fig 16 Locate the Dust Cup Door release button within the trash bag and press to release as you shake the dust cup to empty dust and debris Close the bottom door until it snaps in place Note Opt
13. states do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province IMPORTANT Carefully pack item to avoid damage in shipping Be sure to include proof of purchase date and to attach tag to item before packing with your name complete address and phone number with a note giving purchase information model number and what you believe is the problem with item We recommend you insure the package as damage in shipping is not covered by your warranty Mark the outside of your package ATTENTION CUSTOMER SERVICE We are constantly striving to improve our products therefore the specifications contained herein are subject to change without notice Product Registration Please visit www sharkclean com or call 1 800 798 7398 to register your new Shark product within ten 10 days of purchase You will be asked to provide the store name date of purchase and model number along with your name and address The registration will enable us to contact you in the unlikely event of a product safety notification By registering you acknowledge to have read and understood the instructions for use and warnings set forth in the accompanying instructions 12 ER TOLL FREE 1 800 798 7398 www sharkclean com 13 NV100_26_IB_ENG
14. such as hot coals cigarette butts or matches DO NOT pick up flammable or combustible materials such as lighter fluid gasoline kerosene or use in areas where they may be present DO NOT pick up toxic solutions such as chlorine bleach ammonia or drain cleaner DO NOT use in an enclosed space where vapors are present from paint paint thinner moth proofing substances flammable dust or other explosive or toxic materials DO NOT vacuum up any liquids DO NOT immerse vacuum cleaner in water or other liquids DO NOT use outdoors or on wet surfaces use only on dry surfaces Use extra care when cleaning on stairs Before turning on the vacuum e Make sure that dust cup and all filters are in place after routine maintenance e Make sure that all components and filters are thoroughly dry after routine cleaning e Only use filters and accessories provided by EURO PRO Operating LLC Failure to do so will void the warranty HOSE ATTACHMENTS 31 32 33 34 35 DO NOT put any object into openings Do not use with any opening blocked Keep free of lint hair and anything that may reduce airflow DO NOT use if air flow is restricted if the air paths the hose or the extension tube become blocked turn the vacuum cleaner off Remove all obstructions before you turn on the unit again Keep the end of the hose wands and other openings away from face body and loose clothing Keep rotating brush and suct
15. uum upright Remove Dust Cup Assembly and empty Dust Cup if necessary Check Air Duct behind Dust Cup for clogs clear before replacing Dust Cup Assembly Fig 20 2 HOSE INTAKE OPENING Hold the top of the hose access door and pull firmly to remove Slide the knob to the center and pull out the hose Fig 21 Remove hose from both the unit and handle ends Fig 22 Inspect the length of the hose and remove any obstuctions Remove any obstructions and push the hose back in Slide the knob to the left and snap the hose access door shut NV100_26_IB_ENG_110317_2 indd 10 11 Maintenance Resetting the Motor Thermostat Your Shark Navigator is equipped with a protective Motor Thermostat If the motor should overheat the thermostat shuts off the power TO RESET THE MOTOR THERMOSTAT Press the Power Button to turn the unit Off Unplug the vacuum Check for clogged hose or filter unclog hose and replace filter Refer to Checking for Blockages on page 11 Wait 45 minutes for vacuum to cool then plug in the vacuum Press the Power Switch to start the vacuum NOTE If vacuum still does not start contact Customer Service at 1 800 798 7398 Get even more cleaning from your Shark Navigator by checking out our cleaning accessories assortment at www sharkclean com Bookmark the page and check back often to take advantage of the latest products promotions and prices
16. water and let air dry for at least 24 hours before replacing Do not use a hair dryer or other heating methods to dry 5 Place the felt filter in first then the foam filter 6 Replace the dust cup NV100_26_IB_ENG_110317_2 indd 8 9 8 ER TOLL FREE 1 800 798 7398 L gt Fig 19 CLEANING THE POST MOTOR FILTER 4 Remove the filter cover from the front of the vacuum by pulling up on the tab and pulling the cover away from the vacuum Fig 19 Remove the filter from the frame and wash the filter under the tap using lukewarm water 4 Allow the filter to air dry for 24 hours Do not use a hair dryer or other heating methods to dry 5 Once the filter is dry replace it back into the vacuum 6 Replace the cover by inserting the two tabs into the holes at the top and and then swinging the cover down until it clicks into place NOTE Filters may appear dirty but frequent cleaning of these is not necessary See maintenance schedule above Troubleshooting WARNING gA To reduce the risk of electric shock the power cord must be disconnected before performing maintenance troubleshooting checks PROBLEM POSSIBLE REASONS amp SOLUTIONS Vacuum will not run Check to see if the vacuum is plugged in properly Check the circuit breaker fuse Check the On Off button Vacuum is not picking up dirt Check filters to see if they need cleaning Follow instructions for rinsing and drying the
Download Pdf Manuals
Related Search