SECO-LARM USA EV-1323B12DW User's Manual
Contents
1. 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com a PITNW1 Tel 800 662 0800 949 261 2999 Fax 949 261 7326 E mail sales seco larm com DAY_NIGHT_IMUO604c PMD MANUAL EV 1323C12DW FoRCER 1 3 CCD Color IR Day Night Camera EV 1323B12DW 1 3 CCD B W IR Day Night Camera Weatherproof Fe CC ENFORCER CCD IR Day NIGHT Camera MANUAL Specifications Type Chip Resolution Pickup elements Scanning system Sync Video output Lens Minimum illumination Gamma correction S N ratio Shutter control Backlight compensation Automatic gain control AGC Enclosure of infrared LEDs Max LED range Power source Power consumption Operating temperature Dimensions Weight Dimensions 2 57mm 2 16 68mm EV 1323C12DW NTSC Color camera 1 3 CCD Sony 420 TV lines 1 3 CCD 512 x 492 pixels 2 1 interlace Internal 1V pp composite output 75 ohms F1 8 4 3mm lens included 0 1 lux LED off 0 0 lux LED on 0 45 gt 50dB AGC off Auto Electronic Shutter AES 1 60 1 100 000 sec auto auto IP67 weatherproof 12 Up to 40 ft 12VDC 10 60mA IR off 160mA IR on 14 131 F 10 55 C 34 16 L x 22 4 D 78 X57 mm without sunshield 16 oz 454g EV 1323B12DW EIA B W camera 1 3 CCD Samsung 420 TV lines 1 3 CCD 512 x 492 pixels 2 1 interlace Internal 1V pp composite output 75 ohms F1 8 4 32. a class a digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARRANTY ENFORCER IR Cameras are warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original customer Our obligation is limited to the repair or replacement of any defective part if the unit is returned transportation pre paid to SECO LARM NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2004 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc
3. ENFORCER CCD IR Day NIGHT Camera MANUAL TROUBLE SHOOTING The screen is blank Check that the camera is powered up Check that the power supply s polarity is correct Check that the monitor is powered up Check that the video cable connecting the camera to the monitor is connected properly The screen image is dim Clean the lens using a soft clean cloth Check that the light source is adequate The screen image has poor contrast Adjust the monitor s contrast knob Change the position of the camera The screen image flickers Change the position of the camera The screen image is distorted Change the position of the camera The camera case is hot Check that the correct power supply is in use IR LEDs do not turn on Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see a malfunction like smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no field serviceable components inside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits for
4. e to rotate the camera on its axis This rotates the angle of the video image 10 Tighten the bracket s thumb screw and the adjustment plate so that the camera does not move but not so tight that it cracks the case or bracket 11 Do a final test of the video camera and monitor
5. here it is to be mounted then twist the camera until it is certain that this mounting location is correct Use a pencil to mark the location of the three screw holes in the bracket Disconnect the 12VDC power supply and video cable Camera F BNC connector female Parts List Adjustable Sunshield G Adjustment nut ee Mounting bracket H Mounting holes 7 B 1 x Sunshield 36 cord E DC jack x Mounting bracke 3 x Mounting screws A age 3 x Screw anchors z lt 1 x Manual 6 Do not open or disassemble the camera There are no user serviceable parts inside Do not drop the camera or subject it to strong vibrations Note Many video monitors produce strong electromagnetic fields close to the display CRT especially when the monitor is turned on or during de Gaussing which occurs automatically with many monitors when the monitor is turned on 7 Mount the bracket to the wall using the three included mounting screws If the wall is made of dry wall brick or similar material it may be necessary to use the three included screw anchors Reconnect the 12VDC power supply and video cable Turn the monitor on and make sure the camera is sending the proper video Signal Adjust the camera angle a Loosen and tighten the bracket s thumb screw to turn the camera and change its angle relative to the bracket This ensures the camera is pointing in the right direction b Loosen and tighten the adjustment plat
6. mm lens included 0 1 lux LED off 0 0 lux LED on 0 45 gt 48dB AGC off Auto Electronic Shutter AES 1 60 1 100 000 sec auto auto IP67 weatherproof 12 Up to 40 ft 12VDC 10 110mA IR off 210mA IR on 14 131 F 10 55 C 31 16 L x 24 4 D 78 x57 mm without sunshield 16 oz 4549 2 16 65mm 31 16 78mm 1 3 16 46mm 16 14 5mm ENFORCER CCD IR Day NIGHT Camera MANUAL moop BEFORE STARTING SS Ww N Please read this manual carefully and keep it for future reference Use the camera within given temperature and electricity limits Do not aim the LED light directly at the eyes when the LEDs are on Do not point the camera at the sun Heat could damage the camera even when not in use Do not mount the camera in areas exposed to radiation strong magnetic fields or strong electrical signals INSTALLATION L Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted if necessary Assemble the mounting bracket then screw it into the back of the camera Make sure the mounting base is tightened to the bracket Temporarily connect the camera to the 12VDC power supply Temporarily connect the camera s female BNC connector to the video cable s male BNC connector While watching the monitor hold the camera bracket against the wall by hand w
Download Pdf Manuals
Related Search