SECO-LARM USA ENFORCER 190 User's Manual
Contents
1. ATION ANYWHERE HOW IT WORKS The ENFORCER 190 190S is the most convenient audio discriminator for glass break protection on the market today Designed with the latest technology it is the installer s answer to the problem of sensitivity setting and false alarms A single convenient ENFORCER 190 190S is enough to protect all the windows and doors within a 15 radius when mounted on the ceiling eliminating the need to install unsightly individual detectors on each pane of glass Sensitivity setting is extremely simple with SECO LARM s Yellow turbulence LED patented which eliminates the need for external test meters The relay output is programmed for a 2 second reset y eee2. HE CHANCE OF FALSE ALARMS WITHOUT INCREASING PROTECTION LEAVING A DOOR OR WINDOW OPEN WILL ALSO INCREASE THE CHANCE OF FALSE ALARMS TAMPER PROOFING CASE For extra protection the ENFORCER 190 190S is equipped with an N C Tamper Switch to protect against opening or breaking of the case INSTALLATION SCREW TERMINALS 7 N C TAMPER OUTPUT 6 COMMON TAMPER OUTPUT 5 COMMON GROUND 4 12VDC 3 DRY RELAY N O 2 DRY RELAY COMMON 1 DRY RELAY N C n For N O output use Terminals 2 and 3 a For N C output use Terminals 2 and 1 INSTALLATION HINTS 1 The ENFORCER 190 190S usually receives power from the alarm panel If the ENFORCER 190 190S is connected to a separate power source it should also be connected to a rechargeable battery in case AC power fails Use either Terminals 2 and 3 N O output or 2 and 1 for N C output but not both Close all doors and windows when the ENFORCER 190 190S is in use Mount any optional memory buzzer musical device or any sound generating equipments as far from the ENFORCER 190 190S as possible to reduce the detector s chance of accidental triggering and reducing the chance of a thief finding the ENFORCER 190 190S SPECIFICATIONS POWER 12VDC 7 5V 15V CURRENT DRAIN STANDBY CONDITION 5mA 12V CURRENT DRAIN TRIGGER CONDITION 80mA 12V DETECTOR OUTPUT DRY RELAY CONTACT N O C N C 2A TAMPER OUTPUT N C CONTACT YELLOW LED INDICATES ENVIRONMENTA
3. L NOISE LEVEL RED LED INDICATES TRIGGER SIGNAL SENT TO ALARM TEMPERATURE RANGE 14 F TO 122 F 10 C TO 50 C CASE CONSTRUCTION ABS PLASTIC SIZE 4 5 x 2 8 x 1 1 115mm x 70mm x 27mm WEIGHT 3 350z 95g N oo P The SECO LARM policy is one of continual developments and improvements For this reason SECO LARM reserves the right to change specifications without further notice SECO LARM U S A INC 17811 Sky Park Circle Suite D amp E Irvine CA 92614 SECO LARM ALARM SYSTEMS AND ACCESSORIES Copyright 1997 SECO LARM U S A INC ALL RIGHTS RESERVED Telephone Fax ENFORCER IS A REGISTERED TRADEMARK OF SECO LARM 800 662 0800 714 261 7326 714 261 2999 FILE MI190 P65 MU DEC1 997 ORDER PART 760 362 1 86C SECO LARM ENFORCER 190 190S GLASS BREAK DETECTOR USA PAT UK PAT 4700332 2177797 1041888 TAIWAN PAT 50612 REMARKABLE FEATURES YELLOW TURBULENCE LED PATENTED ALLOWS FAST AND EASY SENSITIVITY ADJUSTMENT WITHOUT EXTERNAL TEST METER YELLOW LED GIVES PINPOINT SENSITIVITY ADJUSTMENT TO ELIMINATE FALSE ALARMS DETECTS THE HIGH FREQUENCY SOUND OF GLASS BREAKING ENFORCER 190 WIDE 25 RADIUS PROTECTION AREA IF CEILING MOUNTED 45 IF WALL MOUNTED ENFORCER 190S WIDE 20 RADIUS PROTECTION AREA IF CEILING MOUNTED 35 IF WALL MOUNTED RED TRIGGER LED TAMPER PROOF CASE INSTALLS WITHOUT RF SHIELDED CABLE COMPACT SIZE AND ATTRACTIVE APPEARANCE ALLOWS INSTALL
4. OPERATING THE ENFORCER 190 190S MOUNTING THE DETECTOR It therefore should be mounted in a location within which every glass window and door to be protected is found For greatest security attach to the wall or ceiling using screws instead of double sided foam tape For larger areas two or more units can be used without fear of interfering with each other SETTING THE SENSITIVITY The ENFORCER 190 190S includes SECO LARM s unique patented Yellow turbulence LED This LED flashes when environmental noise is high enough to cause false alarms thereby allowing instant sensitivity setting without the use of a special external test meter To set sensitivity hold a thin flexible plastic ruler flat against a glass window within the unit s protection range Pick up one end of the ruler while holding the other end down and then let the ruler snap against the glass window This should cause the Yellow LED to come ON but the Red LED should not light If the Red LED comes ON with a slight snap the ENFORCER 190 190S may be too sensitive and the sensitivity control should be turned counterclockwise with a small flat or phillips screwdriver If the Yellow LED does not come ON sensitivity should be increased by turning the control clockwise Continue snapping the ruler on the window until the Yellow LED comes ON but the Red LED does not Repeat this process with each window to ensure the ENFORCER 190 190S is set for every pane of glass Wh
5. en the correct sensitivity is found using the above procedure determine whether the sensitivity is high enough to trigger the alarm by snapping the ruler harder to simulate a break in If the Red LED does not come ON the sensitivity must be increased NOTE For applications within this temperature range the sensitivity will be stable If the temperature should drop below 14 F 10 C the sensitivity of the ENFORCER 190 1908S will increase and the sensitivity setting will need to be decreased If the temperature should rise above 122 F 50 C the sensitivity of the ENFORCER 190 190S will decrease and the sensitivity setting will need to be increased When setting sensitivity make sure the room s environment is as close as possible to what it will be when the ENFORCER 190 190S is in use For instance if the curtains are usually closed at night when the alarm is armed then set sensitivity with the curtains closed If a window in the room is left opened then set the sensitivity with window open The sensitivity should always be retested when the environment of the room changes such as when furniture is moved Depending on the type of glass sensitivity is different when set by tapping the inside or outside of the window with a ruler For best results tap the inside of the window NOTE DO NOT SET SENSITIVITY ANY HIGHER THAN NECESSARY TO PROTECT THE GLASS IN THE DETECTOR S RANGE SETTING SENSITIVITY HIGHER THAN NEEDED INCREASES T
Download Pdf Manuals
Related Search