Sears 486.24412 User's Manual
Contents
1. SEARS owners manual Model No 486 244120 48 DOZER BLADE 48 DOZER BLADE CAUTION Read Rules for Safe Operation and Instructions Carefully Assembly Operation e Customer Responsibilities e Repair Parts Sears Roebuck and Co Hoffman Estates IL 60179 U S A PRINTED IN U S A RULES FOR SAFE OPERATIONS Remember any power equipment can cause injury if operated improperly or if the user does not unde stand how to operate the equipment LOOK FOR THIS SYMBOL TO POINT OUT Aw SAFETY PRECAUTIONS T MEANS ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED Exercise caution at all times when using power equipment 1 Read the tractor and dozer blade owners manuals and know how to operate your tractor before using tractor with the dozer blade attachment 2 Never operate tractor and dozer blade without wearing proper clothing suited to weather conditions and operation of controls 3 Never allow children to operate tractor and dozer blade and do not allow adults to operate without proper instructions 4 Always begin with transmission in first low gear and gradually increase speed as required 48 DOZER BLADE CARTON CONTENTS Also See Page 3 While confirming parts count we suggest that you clear any paint from the 1 8 pin holes in part reference numbers 2 3 and 4 to make assembly easier Blade Assembly Lift Pivot Plate ChanneVPivot Plate Assembly Support Bracket Lift As2. 1 1 4 hex bolt through 3 8 7 i flat washer through pivot bushing through large a 7S NN hole in lift arm link near angle end and through hole in long arm nearest the end Secure with one 3 8 lock washer and one 3 8 hex lock nut See figure 17 NOTE Lift arm link must pivot freely 3 8 HEX LOCK NUT 3 8 X 1 AND LOCK WASHER HEX BOT FIGURE 14 10 Assemble the frame bracket LH under the left hand foot rest of the tractor using two 3 8 x 3 4 hex bolts Tighten securely being careful not to strip threads See figure 15 15 Assemble one 3 8 x 1 hex bolt through second hole form end of long arm Secure with one 3 8 lock washer and one 3 8 hex lock nut This bolt is used as a limit stop for the lift arm link See p figure 17 11 Assemble the lift pivot plate to th left hand frame bracket using two 3 8 x 3 4 clevis pins and 3 8 FLAT WASHER secure wth two 3 32 small hairpin cotters See 3 8 x 1 1 4 figure 15 HEX BOLT PIVOT SONT BUSHING LIFT ARM LEFT SIDE _ 3 8 x 3 4 BOLTS aje x1 m LINK 3 8 LOCK 3 8 HEX ASSEMBLY LOCK NUT CLEVIS PINS FIGURE 17 3 8 x 3 4 HAIRPIN COTTER fd NOTE SMALL LIFT PIVOT PLATE Lift arm link must be positioned FIGURE 15 as shown in figures 17 and 19 16 Relieve spring te asion on lift lever see figure 18 and note below loosening hex jam nut and un screwing adjustrient bolt counter clockwise to obtain 1 4 clearance between bracket and ad justment bol
3. angle to left center right and release grip to lock ADJUSTMENTS A Blade angle iock bars If angle lock bars Do Not completely disengage from slots in pivot plate assembly adjustment of cable is required See figure 29 B Adjust blade springs To change spring tension stand in front of blade assembly adjust the nuts at the upper end of the springs see figure 29 turning counter clockwise to relieve tension and clockwise to increase ten sion Adjust spring adjustment nuts approximately i from end when moving snow or other light mate rial keep spring tension light for safety This frees the blade to spring trip and return if a hidden obstacle is encountered SPRING ADJUSTMENT NUTS OUTSIDE BLADE ASSEMBLY SPRING ADJUSTMENT ASSEMBLY FIGURE 29 KNOW THE TERRAIN AVOID EXCEPTIONALLY SHARP SLOPES OR DROP OFFS WHICH MAY BE HIDDEN BY THE SNOW NEVER RUN THE DOZER BLADE INTO HEAVY MATERIAL AT HIGH SPEED 1 2 LOCK WASHERS N AND _ 1 2 HEX NUTS 1 2 X 2 3 4 HEX BOLTS FIGURE 30 C Dozer spring lockout To lock dozer blade spring trip action for heavy dozer work instail two 1 2 x 2 3 4 hex bolts included in hardware package as shown in figure 30 Secure with two 1 2 lock washers and two 1 2 hex nuts DO NOT OPERATE TRACTOR AND DOZER BLADE AT HIGH SPEEDS WITH SPRING TRIP ACTION IN LOCKED OUT POSITION 11 Blade shoe adjustment Blade shoes on end of
4. blade see figure 31 maybe raised for clean dozing on smooth sur faces or lowered to raise the blade to work on rough or uneven areas Make sure both shoes are set evenly and nuts are tighted securely FIGURE 31 gt NOTE Wheel weights and tire chains should be used with your dozer to improve traction For additional traction install wheel weight on rear of drawbar using a weight bracket kit and one wheel weight from the wheel weight kit These accessories are available at your near est Sears retail or catalog store OPERATION INSPECT THE AREA TO BE WORKED CAREFULLY BEFORE OPERATING THE DOZER BLADE AVOID PIPES ROOTS CURBS OR OTHER HEAVY OBSTRUCTIONS Prepare the tractor engine for cold weather use following instructions furnished with tractor Always begin with transmission in first low gear and gradually increase speed as required If blade is stored in heated area allow tractor and blade to adjust to outdoor temperature before operating fo reduce icing on the metal surfaces ALWAYS LOWER BLADE TO GROUND BEFORE LEAVING TRACTOR TO REMOVE DOZER BLADE pee nee FROM TRACTOR SSB ca 1 y ee Lower blade to ground with blade in the center AIRPIN COTTER lt A straight position EA oe 2 Refer to figure 32 below and cy Y CS A Remove 1 8 hairpin cotter from the lift arm ES NY link and channel assembly KEEPER _ orw ACN COTTERS ey DN m Via B Remove 3 32 small
5. hairpin cotters and 7 16 PLATE O S re d flat washers from each lift assembly arm GUIDE C Remove 3 32 small hairpin cotters from right BRACKET CHANKE and left hand lift pivot plates remove two 3 8 ASSEMBLY ose i ASSEMBLY clevis pins from each side of frame unhook and lower the lift assembly to the ground D Remove lift rod trunnions and hex nuts from each lift link rod See Figure 32 and figure 16 on page 7 FIGURE 33 H Refer to figure 34 and remove hairpin NOTE cotter from end of handle guide to release handle assembly from tractor Frame Brackets do not require re moval for re assembly of mower deck l Save all loose parts and hardware for re See figure 32 assembly of biade to tractor LIFT PIVOT LIFT ASSEMBLY CLEVIS PINS HAIRPIN HANDLE ASSEMBLY HANDLE SUPPORT GUIDE BRACKET fA YLIFT ROD TRUNNION HAIRPIN AND 3 8 HEX NUTS HAIRPIN FIGURE 34 COTTERS COTTER FIGURE 32 E Re install suspension arms and up stop bracket removed on page 5 See figure 9 on page 5 Refer to tractor owners manual to re install and ievel mowing deck Mowing deck must be leveled F Refer to figure 3 and remove 1 8 large hairpin cotters from ends of guide bracket assembly and remove guide bracket assembly G Refer to figure 33 and remove hairpin cotters from end of channel assembly pivot shaft and remove keeper plates Lift the chan nel assembly pivot shaft out of the hitch plates and lo
6. ox p 3 8 STD 0 3 8 SHOULDER 1 2 JAM NUT EL CI7 FANMWAPDSC EVE WNT AU ADT 7416 STD ASSEMBLY INSTRUCTIONS TOOLS REQUIRED FOR ASSEMBLY 1 7 16 Open End or Box Wrench 41 1 2 Open End or Box Wrench 1 9 16 Open End or Box Wrench 1 3 4 Open End or Box Wrench 1 Adjustable Wrench 1 Hammer Refer to carton contents figure on page 2 and figure 1 on page 3 for parts and hardware needed to assemble dozer biade zap NOTE RIGHT HAND R H AND LEFT HAND L H ARE DETERMINED FROM OPERATOR S POSITION WHILE SEATED ON TRACTOR 1 Assemble curved end of angle lock spring into small hole in washer as shown in figure 2 ANGLE LOCK SPRING CHANNEL PIVOT PLATE ASSEMBLY FIGURE 2 2 Assemble the two angle lock bars together as shown in figure 3 using one 3 8 x 1 1 4 carriage bolt down through the top holes with a 3 8 lock washer and a 3 8 hex nut underneath Do not tighten at this time 3 8 X 1 1 4 CARRIAGE BOLT TOP HOLE Q 3 8 HEX NUT 3 8 LOCK WASHER SPRING PIN HOLE CHANNEL PIVOT PLATE ASSEMBLY FIGURE 3 3 Assemble the offset end of angle lock spring into small holes in angle lock bars as shown in figure 3 Slide lock bars through lock bar slot until spring pin hole is aligned with bracket on back side See figure 4 Using a hammer drive 1 4 x 1 spring pin into lock bars until flush with bracket See figure 4 Tighten nut in angle lock bars whi
7. step 1 See figure 12 Adjust hex nuts above and below channel to provide a minimum 1 8 clearance between chan nel and the tractor engine pulley with the stop bolt positioned against front axle frame member See figure 12 onto adjustment bolts on top side of bar Tighten both spring adjustment nuts approximately 1 down from end of bolt threads see figure 13 to provide tension of blade against stop bolts i Adjust stop bolts to tilt blade forward until 1 1 2 distance is obtained between pivot plate and blade assembly crossmember See figure 13 8 Re assemble plactic caps on top ends of spring 12 Assemble 3 8 plain hex nut lift rod trunnion and adjustment bolts lock nut removed from tractor lift link rod in f tractor preparation section onto right and left hand lift link rods untii one thread is below bottom NOTE of nut Tighten nuts lock trunnion in place See figure 16 SEE ADJUSTMENT SECTION ON FRONT PAGE 10 FOR SPRING TENSION LIFT LINK ROD RIGHT SIDE 9 Assemble blade pivot bracket on to top right hand side of channel pivot assembly See figure 14 Assemble two 3 8 x 1 hex bolts down through bracket and plate and secure with two 3 8 lock washers and 3 8 hex nuts underneath PLAIN HEX NUT CHANNEL PIVOT ASS Y LIFT LINK NUT TRUNNION REMOVED EARLIER ONE THREAD EXPOSED FIGURE 16 13 Pre assemble lift arm link to inside of long arm on lift assembly As shown in figure 17 14 Assemble one 3 8 x
8. S OF CHANGE IN DIRECTION CONTROLS Become familiar with all of the controis and ad justments on the tractor and dozer blade before operating Refer to tractor 2yners manual for tractor controls Controls for operating dozer blade are as follows A LIFT CONTROL LEVER Located on right hand side of tractor See figure 28 Move lever forward to lower dozer biade Pull lever back to raise dozer blade Pulling lever all the way back locks dozer blade in up position ATTACHMENT DEPTH CONTROL KNOB LEVER PLUNGER GRIP ASSEMBLY _ DOWN LOCKING NOTCH EEP An HANDLE FIGURE 28 B LIFT LEVER PLUNGER Located on top of lift control ever See figure 28 Pull back on lift controt lever and depress plunger to release WITH THE DOZER BLADE IN THE UP POSITION DO NOT DEPRESS THE PLUNGER WITHOUT HOLDING BACK ON THE LIFT CONTROL LE VER OR DOZER BLADE MAY SUD DENLY DROP C Attachment depth control knob Adjust lift control lever movement with attachment DEPTH CONTROL KNOB see figure 28 for maximum movement between locking notches and to prevent lever from locking in the down lock notch See figure 28 D Blade angle handle and grip assembly Located on right hand side of tractor See figure 28 NOTE Always raise dozer blade and loc n up position before moving angle control handie Depress grip assembly to release blade angle lock and push pull angle control handle forward to move dozer blade
9. ch was lefi loose in step 2 ANGLE LOCK SPRING LOCK BARS 1 4 X 1 SPRING PIN FIGURE 4 NOTE Lock bars should pivot freeiy and when pulled all the way back the channel pivot plate assembly should be unlocked and free to pivot to right or teft position notches 4 Assemble angle stop to top of channel using one 1 4 x 5 8 hex bolt down through left hand hole and one 1 4 hex lock nut under channel figure 5 Do not tighten at this time CHANNEL PIVOT ef 7 Assemble ball end of cable through round hole in cable end fitting and into slot of fitting See See figures 7 and 8 1 4 X 1 1 4 1 4 HEX LOCK NUT HEX BOLT CABLE END FITTING LONG SPACER 1 4 X 5 8 HEX BOLT eae ANGLE STOP FIGURES 5 Assemble 3 8 x 1 1 4 carriage bolt through square hole in cable mount bracket and through square hole in lock bars See figures 6 and 7 Hold cable mount bracket in position as shown in figure 7 and secure with 3 8 lock washer and 3 8 hex lock nut 1 4 HEX LOCK NUT FIGURE 8 8 Assemble 1 4 x 1 1 4 hex bolt down through cable end fitting through long spacer angle stop right hand hole and through channel See figure 8 Secure with 1 4 hex lock nut and tighten the other 1 4 hex lock nut which was left loose in step 4 NOTE Keep cable and fitting in align ment with cable mount bracket when tighten ing nuts ASSEMBLY OF SNOW BLADETO LAWN TRACTOR Tractor Preparation A Rem
10. e stop bolt must be tight ened in place before assembling blade assembly to channel FRONT AXLE FRAME MEMBER 2 Assemble channel assembly to hitch plates at front of tractor as shown in figures 10 and 11 1 ae x 4 HEX BOLT HITCH PLATES 172 X4 CLEARANCE HEX BOLT MINIMUM FIGURE 12 5 Hold biade head upright and guide one end of mount rod into hole near bottom of blade mount gusset See figures 11 and 13 Secure with a hairpin cotter Slide other end of mount rod into other blade mount gusset hole and secure with hairpin cotter FRONT FIGURE 10 SPRING ADJUSTMENT BOLTS 3 Assemble keeper plates over each end of pivot shaft with lip under hitch plates see figure1 1 and _PLASTIC secure with two 1 8 large haizpin cotters through CAP smail holes near each end of shaft BLADE HEAD sc 1 PESE 3 8 HEX NUT CHANNEL ASS Y HITCH PLATES SPRING IS A CHANNEL BLADE MOUNT GUSSE HAIRPIN COTTER MOUNT ROD M M 2000000 T 7 fi r F aa CA SPRING MOUNT EARS FIGURE 13 6 Connect curved end of spring assemblies into spring mount ears See figure 13 Remove plastic cap and one 3 8 hex nut from end of each spring assembly Hold blade back against stop bolts and assemble spring adjustment bolts up through bar Re assemble two 3 8 hex nuts removed earlier HAIRPIN COTTER MOUNT ROD FIGURE 11 4 Adjust 1 2 x 4 stop bolt previously assembled into channel assembly
11. er when requesting service or repair parts for your dozer biade SEARS owners manual All parts listed herein may be ordered from any Sears Service Center and most Sears stores WHEN ORDERING REPAIR PARTS ALWAYS GIVE THE FOLLOWING INFORMATION THE PART NUMBER THE PART DESCRIPTION THE MODEL NUMBER THE NAME OF MERCHANDISE Model No 486 244120 48 DOZER BLADE If the parts you need are not stocked locally your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling LIMITED ONE YEAR WARRANTY ON 48 DOZER BLADE For one year from date of purchase when this dozer blade is main tained and lubricated according to the operating and customer respon sibilities instructions in the owner s manual Sears will repair free of charge any defect in material or workmanship How to Order Repair Parts If this dozer blade is used for commercial or rental purposes this warranty applies for only 90 days from the date of purchase This warranty does not cover repairs necessary because of operator abuse or negligence including the failure to maintain the equipment according to instructions contained in the owner s manual WARRANTY SERVICE IS AVAILABLE BY RETURNING IT TO THE NEAREST SEARS SERVICE CENTER DEPARTMENT IN THE UNITED STATES This warranty applies only while this product is in use in the United States This warranty gives you specific legal rights and y
12. ou may also have other rights which vary from state to state Sears Roebuck and Co D 817WA Hoffman Estates IL 60179 Sears Roebuck and Co Hoffman Estates IL 60179 U S A ee een tees FORM NO 45185 12 92 PRINTED IN U S A
13. ove mower or any other attachment you may have mounted to your tractor Mark all loose parts and save for re assembly Refer to tractor owners manual for removal of mower attachment 3 8 X 1 1 4 oo HEX NUT CARRIAGE BOLT t NS A s e LOCK WASHER FIGURE 6 cas B Remove and save suspension arm with nut and washer from both lift tink rods and up stop bracket 6 Assemble one 5 16 24 hex jam nut onto threaded with nuts and boits from tractor frame to allow end of control cable approximately 3 4 from end Assemble threaded cable end through round hole in cable mount bracket and secure with another 5 16 24 hex jam nut See figure 7 CONTROL CABLE END CABLE MOUNT BRACKET BALL END 5 16 24 HEX NUTS FIGURE 7 assembly of snow blade Also remove the 3 8 self tapping bolts from each side of the tractor frame as shown in figure 9 The lift link nuts will be used tater to install snow blade brackets FRONT TRACTOR FRAME R H SIDE REMOVE 3 8 SELF TAP BOLTS _ LIFT LINK NUT AND WASHER REMOVE AND SAVE FIGURE 9 UP STOP BRACKET 1 Assemble one 1 2 x 4 hex bolt one 1 2 hex nut and one 7 16 standard washer into top of slotted hole in channel assembly Assemble one 7 16 standard washer and one 1 2 hex nut on bottom of 1 2 bolt under channel assembly See figure 10 DO NOT TIGHTEN AT THIS TIME NOTE The stop bolt must be located so that CENTER of bolt contacts the front axle Th
14. p plastic tie around handle tube and cable see figure 24 assembling end of tie through lock Pull plastic tie tight to retain cable to handle tube near front of tractor hood Cut off extra plastic end 28 Assemble grip assembly to handle assembly us ing one 5 16 x 1 1 2 hex bolt and one 5 16 hex lock nut NOTE Do not over tighten lock nut grip assembly must pivot freely 5 16 x 1 1 2 HEX HEX BOLT LOCK NUT CABLE END FITTING 5 16 HEX HANDLE LOCK NUT ASSEMBLY FIGURE 25 29 Assemble ball end of cable see figure 23 through round hole in cable end fitting and into slot of fitting See figure 25 Assemble cable end fitting over 1 4 weld bolt on grip assembly and secure with one 1 4 hex lock nut NOTE Do not over tighten lock nut cable fitting must pivot freely R H HITCH PLATE L H HITCH PLATE SHAFT END GUIDE BRACKET ASSEMBLY FIGURE 26 30 Assemble guide bracket assembly shaft end into the feft hand hitch plate See figure 26 Slide guide assembly back to the right and into the hole in the right hand hitch plate and secure with a hairpin cotter on each end See figure 27 Lower front end of guide bracket assembly to straddle channel assembly See figure 27 CHANNEL ASSEMBLY R H HITCH PLATE AVJ HAIRPIN COTTER 2 l COTTER r GUIDE BRACKET ASSEMBLY CHANNEL ASSEMBLY FIGURE 27 OPERATION INSTRUCTIONS AND ADJUSTMENTS HIDDEN OBJECTS CAN CAUSE SUDDEN STOP
15. sembly Handle Assembly w grip Guide Bracket Assembly Angle Lock Bars Blade Pivot Bracket Grip Assembly Frame Bracket RH Control Cable Assembly Frame Bracket LH Spring Assembly Parts Package Shown on Page 3 A h mh ee PAF ek mek wh ed AD at nur _ aaa oO yee tine all ENXKXXE lt CAODOVOZErMAC LOMMGOTUY a Se at A Sa a A A CTA QM Hoa uns OOM a alm 1 4 x 5 8 Y 1 4 LOCK NUT 1 4 x 1 1 4 O 3 8 x 1 1 4 v2 Lock S 3 8 lock 5 16 LOCK NUT SSN NANT 3 8 x 1 1 4 1 2 NUT CONTENTS OF PARTS PACKAGE Figure 1 DESCRIPTION Stop Angle Keeper Plate Lift Arm Link Spring Pin 1 4 x 1 Cable Mount Bracket Nylon tie Cable Fitting End Angle Lock Spring Shoulder Bolt Hex Whizlock Nut 3 8 16 Thread Hairpin Cotter 1 8 Hex Bolt 5 16 18 x 1 1 2 Hex Lock Nut 5 16 18 Thread Hex Bolt 1 2 13 x 2 3 4 Lock Washer 1 2 Hex Nut 1 2 13 Thread Carriage Bolt 3 8 16 x 1 1 4 Lack Washer 3 8 Hex Lock Nut 3 8 16 Thread Hex Bolt 3 8 16 x 1 1 4 Flat Washer 3 8 Std Pivot Bushing short Hex Bolt t 4 20 x 1 1 4 Spacer long Hex Lock Nut 1 4 20 Thread Hex Bolt 1 4 20 x 5 8 Hex Bott 3 8 16 x 1 Hex Jam Nut 5 16 24 Thread Clevis Pin 3 8 Dia x 3 4 Lg Hairpin Cotter 5 32 Handle Guide Hex Bolt 1 2 13 x 4 Lg Hex Jam Nut 1 2 13 Flat Washer 7 16 Std Lift Rod Trunnion Hex Nut 3 8 16 Thread Hex Bolt 3 8 18 x 3 4 Lg J 3 8 WHIZLOCK NUT
16. small hairpin cotters Secure ends of pivot shaft to each lift pivot plate with 1 8 large hairpin cotter See figures 20 and 21 RIGHT HAND SIDE VIEW CLEVIS PINS ASSEMBLY LIFT PIVOT PIVOT SHAFT CLEVIS PINS PLATE FIGURE 21 22 Assemble support bracket onto right hand side of tractor using two 3 8 x 1 hex bolts inside and secure with 3 8 lock washers and 3 8 hex lock nuts on outside See figure 22 HAIRPIN O COTTER Pa VA SUPPORT BRACKET 25 HP e LIFT LEVER 3 8 x 1 HEX BOLTS FIGURE 22 23 Assemble handle guide with loop outside at top of support bracket and secure with one hairpin cotter inside See figures 22 and 23 HAIRPIN HANDLE COTTER GUIDE END 5 16 24 HEX NUTS EAR OUTSIDE GUIDE SUPPORT BRACKET CONTROL CABLE END FIGURE 23 24 Assemble handle assembly down through handle guide as shown in figure 23 Secure lower end of handle to top side of blade piv t bracket with special shoulder bolt on top and 3 8 hex whizlock nut underneath See figure 24 25 Assemble one 5 16 24 hex nut onto threaded end of control cable approximately 3 4 from end Assemble threaded end of cable up through cable mount ear and secure with second 5 16 24 hex nut See figure 24 26 Assemble handle grip on upper end of handle assembly if not already pre assembled See figure 23 Pa SPECIAL SHOULDER BOLT 3 8 HEX WHIZLOCK NUT FIGURE 24 27 Wra
17. t il NOTE Tractor lift lever must be positioned all the way back and locked in position BACK VIEW TRACTOR gee ADJUSTMENT BOLT jay wD yD a SPRING 4 BUSHING ATTACHMENT e LIFT SPRING FIGURE 18 17 18 19 Move attachment lift lever all the way forward and lock in position See figure 28 on page 10 Assemble lift arm link over channel rod and insert pivot shaft end from R H side of tractor into hole in L H lift pivot plate See figure 19 Secure lift arm link to channel rod with 1 8 large hairpin cotter See figure 19 Assemble the frame bracket RH under the right hand foot rest of the tractor using two 3 8 x 3 4 hex bolts Tighten securely taking care not to strip threads See figure 19 RIGHT HAND SIDE VIEW 3 8 X 3 4 FRAME BRACKET SHAFT END LIFT ASSEMBLY FIGURE 19 20 Assemble trunnions that were assembled to the lift ink rods in step 12 through lift assembly arms and secure with 7 16 flat washers anda small hairpin cotters Note Trunnions must be posi tioned to outside of lift seromely arms See figure 20 RIGHT HAND SIDE VIEW FRONT 7 16 FLAT LIFT LINK ROD HAIRPIN COTTER re _ LIFT ASSEMBLY LIFT ROD TRUNNION ARMS PLAIN NUT AND LOCK NUT FIGURE 20 21 Assemble lift pivot plate over right hand end of lift assembly pivot shaft and connect to outside of frame bracket using two 3 8 x 3 4 clevis pins from inside Secure with two 3 32
18. ustment Spring 1509 90 1 jHex Bolt 1 4 20 x 1 1 4 44071 2 Hex Bolt 3 8 16 x 3 1 2 43866 1 Hex Bolt 1 4 20 x 5 8 43015 4 Hex Nut 3 8 16 43013 3 Hex Lock Nut 1 4 20 44074 2 Plastic Cap 3 8 23658 1 Spacer 62868 1 Guide Bracket Ass y 43085 1 Hex Bolt 5 16 18 x 1 1 2 23646 1 Blade Pivot Bracket 44044 4 jClevis Pin 3 8 Dia x 3 4 Lg 62560 1 Tube Handle Ass y 43055 6 Hairpin Cotter 3 32 62561 1 Release Grip Ass y 43087 1 Hex Bolt 3 8 16 x 1 1 4 746 0366 1 Control Cable Ass y 43070 1 Washer 3 8 Std Wrt 62562 1 Handle Guide 23625 i Pivot Bushing 23728 1 Support Bracket 43001 5 Hex Bolt 3 8 16 x 1 62951 1 Lift Ass y 712 0256 4 Hex Jam Nut 5 16 24 45100 1 Hex Bolt 1 2 13 x 4 731 0869 i Plastic Grip 23922 2 Lift Pivot Plate 43019 2 jHex Jam Nut 1 2 13 23655 1 Stop Angle 43352 4 Washer 7 16 Std Wrt 23624 2 Keeper Plate 23923 1 Frame Bracket LH 23151 2 Angle Lock Bar 23924 1 Frame Bracket RH 23631 1 Lift Arm Link 46001 2 Lift Rod Trunnion 43349 1 Spring Pin 1 4 x 1 43015 2 Hex Nut 3 8 16 Thread 05762 1 Cable Mount Bracket 43407 4 Hex Bolt 3 8 16 x 3 4 Long 726 0178 t Nylon Tie Cable 45185 1 Owners Manual BEN aS ee OE nar Sale CAY Sears Roebuck and Co reserves the right to make any changes in design or Improvements without imposing any obligation to install the same upon its items heretofore manufactured 48 DOZER BLADE Always mention the Model Numb
19. w removal or dozing heavy materials Weight each Fits 30 Ib Lawn Tractor with 8 in rims 33 Ib Lawn or Yard Tractors with 10 in rims 55 ib Garden Tractor with 12 in rims Wheel weight mounting bracket is available to mount one 55 pound weight on the rear of your tractor frame for added traction 13 48 DOZER BLADE REPAIR PARTS FOR MODEL Sl REPAIR PARTS LIST FOR MODEL 48 DOZER BLADE 62554 48 Blade Ass y 746 0260 Cable Fitting End R3132J z Shoe 43348 i Angle Lock Spring 43079 8 Carriage Bolt 5 16 18 x 1 738 0234 4 Shoulder Bolt Special 43081 8 Washer 5 16 Std Wrt 44072 1 Hex Whizlock Nut 3 8 16 43086 8 Lock Washer Spring 5 16 7071 1 Handle Grip 3 4 43083 8 Hex Nut 5 16 18 43343 10 Hairpin Cotter 1 8 23639 1 Wear Plate 48 43064 1 jHex Lock Nut 5 16 18 62556 1 Pivot Plate Ass y 41596 2 Hex Bolt 1 2 13 x 2 62944 1 Channel Ass y 712 0206 6 Hex Nut 1 2 13 710 0741 1 Hex Bolt 3 4 10 x 3 1 2 43510 2 Hex Bolt 1 2 13 x 2 3 4 1640 162 1 Washer 3 4 43353 2 Lock Washer Spring 1 2 40436 1 Hex Jam Nut 3 4 10 710 0305 2 Carriage Bolt 3 8 16 x 1 1 4 736 0306 1 Washer 3 4 Special 43003 8 Lock Washer Spring 3 8 40598 1 Hex Lock Nut 3 4 10 43082 8 Hex Lock Nut 3 8 16 G466R 2 Blade Adj
20. wer channel assembly to the ground 12 CUSTOMER RESPONSIBILITES Ouring the operating season check all bolts nuts and hairpin cotters to be sure they are secure For improved snow removal performance coat the blade with automotive type paste wax STORAGE When the dozer is not being used remove all dirt and rust and touch up with paint Apply a light coat of grease or rust preventative to the biade and oil pivot points Store in an area where it is protected from weather LUBRICATION Oil all pivot points so they will work freely SCRAPER BAR After extensive use and wear the scraper bar may be reversed to utilize the unused top edge See figure 35 a BLADE SSS ASSEMBL AE iS EE X SCRAPER a BAR CARRIAGE BOLTS LOCK WASHERS AND NUTS FIGURE 35 Attachments That Add to the Usefulness of Your Craftsman Tractor Seats offers a wide variety of attachments that for your tractor Many of these are listed below with brief explanations of how they can help you Most of these attachments do not require additional hitches or conversion kits those that do are indicated and are designed for easy attaching and detaching You may order these attachments at most Sears retail stores catalog sales offices and through the catalog Tire Chains are heavy duty closely spaced with extra large cross links that give smooth ride and outstanding traction Wheel weights for rear wheels provide needed traction for sno
Download Pdf Manuals
Related Search