Scotsman Ice C1448 User's Manual
Contents
1. Wey SA SA SA A SA SA ey ea Gs Inspect Orifice Holes Inspect Water Distributor 14 Locate ice thickness sensor Squeeze mounting legs together to release sensor Wash the metal surfaces of the sensor and the adjustment screw with ice machine cleaner solution Also wash the water distributor and curtain with the ice machine cleaner solution 15 Locate water level sensor Squeeze catches together and pull up to remove sensor Wash metal surfaces of sensor with ice machine cleaner solution 16 Mixa solution of locally approved sanitizer Note A possible sanitizing solution may be made by mixing 1 ounce of liquid household bleach with 2 gallons of warm 95 115 F potable water C1448 C1848 C2148W Air and Water Cooled User Manual 17 Thoroughly wash all surfaces of the ice thickness sensor water level sensor curtain and water distributor with the sanitizer solution 18 Thoroughly wash all interior surfaces of the freezing compartment including evaporator frames back wall evaporator cover and the part of the top panel covering the freezing compartment with the sanitizer solution 19 Return water level sens2. x de Css T cit Air Filter Removal Maintenance Air cooled condenser If the machine has been operated without a filter the air cooled condenser fins will need to be cleaned Push and release the Off button Wait until the machine stops If there is imbedded grease use a commercial coil cleaner to wash out the grease Dust can be blown out with compressed air from the back with a vacuum cleaner operating in the fan area Be careful not to damage the condenser s fins Use a fin comb to straighten any bent fins Exterior Panels The front and side panels are durable stainless steel Fingerprints dust and grease will require cleaning with a good quality stainless steel cleaner Water filters If the machine has been connected to water filters check the cartridges for the date they were replaced or for the pressure on the gauge Change cartridges if they ve been installed more than x months or if the pressure drops too much when the ice machine fills with water November 2006 Page 22 C1448 C1848 C2148W Air and Water Cooled User Manual What to do before calling for service Reasons the machine might shut itself off e Lack of water e Freeze cycle takes too long e Harvest cycle takes too long e High discharge temperature e Controller self test failure Check the fo
3. The hot gas valves and harvest assist devices will activate then the compressor and water pump will Start If its an air cooled model the fan s motors will begin to turn The display will show a continuous F Five seconds later the hot gas valves will close and the harvest assist device will return to its standby position Warm air will be discharged from air cooled models 6 Observe the Ready for Harvest indicator light It may blink early in the cycle that is normal The control will ignore that signal for the first 6 The hot gas valves open the air cooled fan motors shut off and the harvest assist mechanisms are activated The flush valve opens to drain some water when it does the inlet water valve opens to refill the reservoir After a few seconds the flush valve closes but the inlet water valve continues to fill the reservoir Harvest continues until the ice is released as a unit and forces the curtain to open When both curtains re close the controller returns the unit to a freeze cycle 10 Check the ice harvested for proper bridge thickness The ice bridge is factory set at 3 16 inch If needed adjust bridge thickness Do NOT make it too thin 11 Determine the water flush setting from the table below If desired change the setting to accommodate the local water conditions 12 Return the front panel to its normal position and secure it to the machine 13 Instruct the user in the operation of the machine and its maint
4. e Remove the build up of mineral scale from the ice machine s water system and sensors e Sanitize the ice machine s water system and the ice storage bin or dispenser e Clean or replace the air filter and clean the air cooled condenser air cooled models only It is the User s responsibility to keep the ice machine and ice storage bin in a sanitary condition Without human intervention sanitation will not be maintained Ice machines also require occasional cleaning of their water systems with a specifically designed chemical This chemical dissolves mineral build up that forms during the ice making process Sanitize the ice storage bin as frequently as local health codes require and every time the ice machine is cleaned and sanitized The ice machine s water system should be cleaned and sanitized a minimum of twice per year 1 2 Remove the front panel Remove the evaporator cover If the machine is operating push and release the Harvest button When the machine completes the Harvest cycle it will stop If the bin is full 6 shows in display push and release the Off button Remove all ice from the storage bin or dispenser Push and release the Clean button The yellow Clean light will blink and the display will show C The machine will drain the reservoir and refill it Go onto the next step when the reservoir has filled Pour 24 ounces of Scotsman Nickel Safe ice machine cleaner into the rese
5. tae eee eee se eee ue 2 Page 12 Final Check List 2404424 65e8 Se ee eee eget eee taee eee eSebSanteas ees Page 13 Initial Start Up Libia i e a a eee these base bw ae batdeui Page 14 Adjustments ag a ok ee ele Oe LEI Ree ORAS LE Page 15 WalermusShseulng a e e soea sa 2 we oe se oe ee eR ERE Pe MAR eee eee a Page 16 Use and Operation suini ni Page 17 Switches aoao bee eauw wan eka beeeedeebe eae wanes Page 18 Options and Other Information 2 2 Page 19 Cleaning Sanitation and Maintenance 2 a a a a Page 20 Air cooled condenser filter 1 1 a a Page 22 What to do before calling for service LL Page 23 Note any Caution or Warning symbols when they appear on the product or in this manual They indicate potential hazards November 2006 Page 1 C1448 C1848 C2148W Air and Water Cooled User Manual Installation Product Specifications Location Limitations The product is designed to be installed indoors in a controlled environment Air cooled models discharge very warm air into the room out the back Space must be allowed at the left side and back for air intake and discharge Water cooled models discharge warm water into the building s drain Space needs to be provided on both sides and above for service access Space Limitations Note Although the machine will function ice capacity of air cooled machines will be significantly reduced with minimal clearance at the sides back and top Some space
6. 3 taste and odor filter system or the ADS AP3 Aqua Patrol system RO water This machine can be supplied with Reverse Osmosis water but the water conductivity must be no less than 10 microSiemens cm Condenser Water Supply filtration not recommended for this water supply GPH 70 degree water C1448W 70 C1848W 106 C2148W 110 Potential for Airborne Contamination Installing an ice machine near a source of yeast or similar material can result in the need for more frequent sanitation cleanings due to the tendency of these materials to contaminate the machine Most water filters remove chlorine from the water supply to the machine which contributes to this situation Testing has shown that using a filter that does not remove chlorine such as the Scotsman Aqua Patrol will greatly improve this situation while the ice making process itself will remove the chlorine from the ice resulting in no taste or odor impact Additionally devices intended to enhance ice machine sanitation such as the Scotsman Aqua Bullet can be placed in the machine to keep it cleaner between manual cleanings Water Flush Cube ice machines use more water than what ends up in the bin as ice While most water is used during ice making a portion is designed to be drained out every cycle to reduce the amount of hard water scale in the machine That s known as water flush and an effective flush can increase the time between
7. a 2 Zu Ce Installation and Scotsman User s Manual Models C1448 C1848 C2148W Nodis C1448 C1848 C2148W Air and Water Cooled User Manual Introduction The design of this modular cuber is the result of This installation and user manual is divided into years of experience and testing Standard features three main sections Installation which provides include front accessible indicator lights and on off the trade person with the information needed to set switches that provide the user with fast access to up and install this product Use and Operation critical information and easy operational control which provides the user with the information to use When desired optional controls can add features the product and Maintenance which provides the like ultrasonic bin ice level sensing seven day user with the information needed keep it operating programmable bin ice level setting remote lock out efficiently and more Table of Contents Installation Product Specifications 2 1 a a a Page 2 PIOdUcriniormalioniz si s Page 3 Product Description amp Electrical Requirements a aoao a a a a Page 4 WA a ee rr prag anrea aaae a a a pa ae Page 7 Panel REMOVAL s s s is 5 ds ete 48 Pee SEER SEER IL Page 8 Uncrate and Set Up Page 9 Plumbing Requirements su ig a a na Page 10 Dialisi ul EU ee eo ee ee oY Page 11 FICCWICd cus Ga aa Sok wa e Rae dee Geese
8. abinet Install new tubing when replacing a prior ice machine as the tubing will have been sized for the old model and might not be correct for this one 1 Connect water supply to water inlet fittings Note This NSF listed model has a 1 anti back flow air gap between the end of the water inlet tube and the highest possible reservoir water level no back flow device is required for the potable water inlet 2 Connect drain tubing to drain fittings Water Inlet Connection Potable Water _57 Supply Optional Water Filters Floor Drain 3 Route the drain tubing to building drain Follow local codes for air gap Use rigid drain tubes and then route them separately do not Tee into the bin s drain or if water cooled Tee the condenser drain into the reservoir or bin drain Vent the reservoir drain A vertical vent at the back of the drain extended about 8 10 will allow the gravity drain to empty and also keep any surges during draining from discharging water Horizontal runs of drain tubing need a per fall per foot of run for proper draining Follow all applicable codes Water Cooled Condenser Inlet Reservoir Drain Water Cooled Condenser Drain I Water Supply and Drain Connections November 2006 Page 11 C1448 C1848 C2148W Air and Water Cooled User Manual Electrical The machine is not supplied
9. al control state November 2006 Page 16 C1448 C1848 C2148W Air and Water Cooled User Manual Use and Operation Once started the ice machine will automatically make ice until the bin or dispenser is full of ice When ice level drops the ice machine will resume making ice Caution Do not place anything on top of the ice machine including the ice scoop Debris and moisture from objects on top of the machine can work their way into the cabinet and cause serious damage Damage caused by foreign material is not covered by warranty There are four indicator lights at the front of the machine that provide information on the condition of the machine Indicator Lights _ _ e C e e Note A Component Indicator Light switches ON to indicate that the component is operating e Power Status _ _ e Water Note There are two Curtain Switch lights SW1 and e Clean SW2 A curtain switch light is ON when a curtain is either open or not present Light indicators amp their meanings Indicator Lights amp Their Meanings Power Status Water De Scale amp Sanilize Steady Green Normal bin full or making ice Blinking Green sali vest Switching on or off Failure Blinking Red Diagnostic shutdown or if making Lack of ice temperature sensor failure water Time to de scale Yellow a and sanitize Blinking Yellow In Cleaning mode Light
10. enance requirements 14 Fill out and mail warranty registration form Typical Ice Making Cycle Times minutes Listed times are for clean machines in proper installations Cycle length at start up will be longer until the system stabilizes l 50 F water 70 F water 7 During the Freeze cycle open and close the curtains The SW1 and SW2 lights on the C1448A 12 14 14 16 control board will blink ON when each curtain is opened and OFF when closed o UE ball C1848A 9 11 12 14 Note Moving a curtain during the Freeze cycle has C1848W 9 11 10 12 no affect on the control but will cause water to flow into the cube chute C2148W 9 11 10 12 8 When the ice has frozen enough the Ready for Harvest indicator light will be on steady After its been on steady for a few seconds Harvest will begin 9 The display shows an November 2006 Page 14 C1448 C1848 C2148W Air and Water Cooled User Manual Adjustments Bridge Thickness For Service Tech Only 1 8 3 16 brid 1 Push and hold Off till the machine stops 7 2 Remove evaporator cover 3 Remove curtain 4 Use a box wrench and rotate the bridge thickness adjustment screw in 1 8 turn increments CW to increase bridge thickness Rotate CCW to decrease bridge thickness Too Big Just Right for Just Right for T00 Small Caution Do not make the bridge too thin or the calce Medium Cube machine will not harvest proper
11. esigned to be placed on an ice storage bin or an ice dispenser Many installations only require the matching bin but some also require an adapter to be placed between the bin and the cuber or between the dispenser and the cuber This product cannot be stacked See the chart for application information Model Number Description Example e C1448SA 32A e C cuber e 14 nominal ice capacity in 100s of pounds e 48 nominal width of cabinet e S Cube size S small or half dice cube M medium or full dice cube e A Condenser type A air cooled W water cooled e 32 Electrical code 32 208 230 single phase 3 208 230 three phase e A Series revision code A first series Note In some areas of this manual model numbers may include only the first five characters of the model number meaning that the cube size condenser type and voltage differences are not critical to the information listed there Options There are several field installed options that can be installed at initial start up or later They include e Vari Smart adjustable ice level system e SmartBoard advanced feature control Some installations require bin adapters See the table below Standard Bin Applications Adapter information BH1100 Model BH900 B948S BH1300 BH1600 ml Direct Fit no No adapter dapter needed needed c2148 Note If previously equipped with stainless steel baffle KBAFFLE3 remove and replace with o
12. good condition Broken doors hinges or warped walls are reason for considering a new bin e The used bin top edge gasket must be replaced Water leaks could occur if the gasket tape is not replaced e The used bin should be the proper size for the ice machine head November 2006 Page 9 C1448 C1848 C2148W Air and Water Cooled User Manual Plumbing Requirements All models require connection to cold potable Water Filters water A hand actuated valve within site of the machine is required Air cooled models have a If connecting to water filtration filter only the water single 3 8 FPT inlet water connection a 3 8 FPT to the reservoir not to the condenser Install new to 3 8 male flare adapter is supplied with the cartridges if the filters were used with a prior machine and can be used if desired machine A triple head filter is recommended Either the Scotsman SSM3 taste and odor filter system or Water Fitting the ADS AP3 Aqua Patrol system Connection Water cooled models have the same inlet fitting plus an additional 3 8 FPT condenser inlet water connection November 2006 Page 10 Drains C1448 C1848 C2148W Air and Water Cooled User Manual All models require drain tubing to be attached to them Air cooled models have a single FPT drain fitting in the back of the cabinet Water cooled models have the same fitting plus an additional 1 2 FPT drain fitting in the back of the c
13. he model and serial number tag located behind the front panel See the illustration for the dataplate and serial tag locations Write the model and serial number of this product here November 2006 Page 4 C1448 C1848 C2148W Air and Water Cooled User Manual Cabinet Layout Air Cooled 15 2 6 00 r MINUMUM FOR UTILTY CONNECTIONS PLAN VIEW 152 6 00 MINIMUM FOR AIR VENTILATION SIDE VIEW FRONT VIEW November 2006 Page 5 C1448 C1848 C2148W Air and Water Cooled User Manual Cabinet Layout Water Cooled 15 2 6 00 MINUMUM FOR UTILTY CONNECTIONS PLAN VIEW 152 6 00 MINIMUM FOR AIR VENTILATION SIDE VIEW FRONT VIEW November 2006 Page 6 Water C1448 C1848 C2148W Air and Water Cooled User Manual The quality of the water supplied to the ice machine will have an impact on the time between cleanings and ultimately on the life of the product There are two ways water can contain impurities in suspension or in solution Suspended solids can be filtered out In solution or dissolved solids cannot be filtered they must be diluted or treated Water filters are recommended to remove suspended solids Some filters have treatment in them for suspended solids Check with a water treatment service for a recommendation Scotsman filters A triple head filter is recommended for the potable water Either the Scotsman SSM8
14. ine operation including cycle time e Calculation of average cycle time e Recall of malfunctions with the time they occurred SmartBoard Advanced Feature Control See Instructions for Available Features 02 4293 01 Rev A Ice The cuber drops ice in large sections That ice will break up into random parts as it falls into the bin but some large sections may remain on top of the ice in the bin When removing ice tap the groups of ice with an ice scoop to separate them into smaller units In a dispenser this ice will break up into mostly individual cubes as the dispense mechanism moves the ice Heat Air cooled models will generate heat when in operation That heat is discharged out the back of the cabinet Noise The ice machine will make noise when it is in ice making mode The compressor fan motors if air cooled and water pump all produce some sound It is also normal to hear some cracking just before the harvest cycle begins In addition during the harvest cycle the harvest assist solenoid will click twice as it pushes the ice out and returns to its normal position The ice harvests as a unit or slab which makes some noise when it impacts the bin or dispenser These noises are all normal for this machine November 2006 Page 19 C1448 C1848 C2148W Air and Water Cooled User Manual Cleaning Sanitation and Maintenance This ice system requires three types of maintenance
15. is recommended for service and maintenance purposes on all models 6 of space at the sides and back are required for adequate operation To get the most capacity locate the machine away from heat producing appliances and heating ducts Provide several feet of space to the left for maximum ice capacity Walls or other large machines near to the ice machine might also cause a reduction in ice capacity One foot behind and two feet above will be required to make rated capacity Airflow is in the front in the left side out the back as viewed from the front A C7 Airflow Direction Environmental Limitations Minimum Maximum Air temperature 100 F Water 40 F 100 F temperature Water pressure 20 psi 80 psi Power supply acceptable voltage ranges Minimum Maximum 208 230 volt 198 volts 253 volts model Warranty Information The warranty statement for this product is provided separately from this manual Refer to it for applicable coverage In general warranty covers defects in material or workmanship It does not cover maintenance corrections to installations or situations when the machine is operated in circumstances that exceed the limitations printed above November 2006 Page 2 Product Information C1448 C1848 C2148W Air and Water Cooled User Manual The product is a modular cuber That type of machine is d
16. llowing 1 Has the water supply to the ice machine or building been shut off If yes the ice machine will automatically restart within 25 minutes after water begins to flow to it 2 Has power been shut off to the ice machine If yes the ice machine will automatically restart when power is restored 3 Has someone shut the water off to a water cooled unit If yes the ice machine may need to be manually reset 4 Is the curtain open because some ice is stuck under it If so remove the ice and the machine should start in a few minutes Note Curtain can be removed amp replaced anytime the machine is in a standby mode or when it is ina freeze cycle Removal of the curtain during harvest terminates harvest at that point and if left off will result in the machine shutting off Ice Stuck Under Curtain To Manually Reset the machine e Push and release the Off button e Push and release the On button OF S WITCN To Shut the Machine Off 1 Push and hold the Off button for 3 seconds or Do until the machine stops ___ 7 O il ON Swi Reset or Switch Off November 2006 Page 23 a Scotsman SCOTSMAN ICE SYSTEMS 775 Corporate Woods Parkway Vernon Hills IL 60061 800 533 6006 www scotsman ice com ns d S 17 3083 02
17. ly Bridge thickness adjustments are not covered by warranty Ice Bridge Thickness Measurement 5 Return curtain to its normal position 6 Push and release the On button Check next harvest of ice Repeat steps 1 6 if needed Note Water cooled models the refrigeration system discharge pressure is factory set at 245 da PSIG which should yield a freeze cycle discharge water temperature of about 105 110 degrees F i Adjust if necessary edi Ice Thickness Sensor November 2006 Page 15 C1448 C1848 C2148W Air and Water Cooled User Manual Water flush setting The water flush is factory set to the automatic position suitable for most water conditions The setting can be changed to one of 5 manual settings or left on automatic deed bs a i 4 Heav 3 A Automatic setting Minimum Moderate Standard Y Maximum RO water Factory Any with Water ae Setting for High TDS conductivity not Type typical water less than 10 equivalent i i water microSiemens cm Status De Scale zlee oo Power Water To set 1 Switch the machine OFF by holding the Off button in until a number or the letter A shows on the display 2 Press and release the On button repeatedly until the number on the display corresponds to the desired setting 3 Press and release the Off switch again to return to the norm
18. needed water system cleaning In addition this product is designed to automatically vary the amount of water flushed based on the purity of the water supplied to it The water flush rate can also be set manually Adjustments of flush due to local water conditions are not covered by warranty November 2006 Page 7 C1448 C1848 C2148W Air and Water Cooled User Manual Panel Removal 1 Locate and loosen the two screws at the front edge of the top panel Pull the front panel out at the top until it clears the top panel Lift the front panel up and off the machine Remove two screws at front edge of top panel Lift up the front of the top panel push it back an inch then lift to remove Locate and loosen the screw holding each side panel to the base Pull the side panel forward to release it from the back panel Switch Bezel All models ship with the On and Off switches front accessible if desired the On and Off switches can be covered up to prevent unauthorized use by changing the bezel in the front panel s trim strip A cover up bezel ships loose with the machine To change bezels Remove the front panel and refer to the instruction label on the inside of the front panel Push snaps of the standard bezel in and pull the bezel out of the front panel Locate other bezel Push into t
19. not desired start up process and then resume ice making Use of control Control Options There are two optional field installed controls that A 5 rs OF Pa can be on this machine AIS E e Vari Smart KVS Adjustable ice level control e SmartBoard KSB Advanced Feature control VariSmart Control Area I There are several positions the ice level can be set to including Off knob and label indicators lined up where it fills the bin until the standard bin control shuts the machine off See the kit s instructions for complete details Rotate the adjustment post to the desired ice level The machine will fill up to that level and when it shuts off the indicator light next to the adjustment post will be On Note Ice will build up in the bin or dispenser at an angle the distances listed above will be from the sensor to the top of the ice directly beneath it The actual distance between the highest point of the ice may be closer or further away depending upon the angle of the ice November 2006 Page 18 Options and Other Information C1448 C1848 C2148W Air and Water Cooled User Manual SmartBoard When this option is present there is an additional display panel in the area below the main control board It is not visible when the front panel is on The SmartBoard s features include Seven day programmable ice level setting when used with the optional Vari Smart ice level control e Recording of mach
20. off No power Switched off All Blinking Unit remotely locked out check with leasing company Normal Normal If the Water light is on the machine has senseda If the Clean light is on the machine has determined lack of water Check the water supply to the that it may need to be cleaned Contact an machine The water may have been shut off or the authorized Scotsman service agent and have the water filter cartridges need to be changed machine cleaned de scaled and sanitized November 2006 Page 17 C1448 C1848 C2148W Air and Water Cooled User Manual Switches The panel in the front of the machine can be flipped Adjustable ice level control up to access two switches on and off When this option is present there is an adjustment Status De Scale post and an additional indicator light to the right of the four indicator lights mentioned above The A 5 a ai ultrasonic ice level control allows the use to control the point that the ice machine will stop making ice before the bin or dispenser is full Reasons for this Power Water include e To switch the machine OFF push and e Seasonal changes in ice used release the Off button The machine will shut e Planning to sanitize the bin off at the end of the next cycle e Faster turnover for fresher ice e To switch the machine ON push and release e Certain dispenser applications where the On button The machine will go through a maximum ice level is
21. or ice thickness sensor water distributors and curtains to their normal positions 20 Push and hold the clean button to drain the reservoir Push and release the clean button again and when the flush valve indicator light goes out immediately pour the remaining cleaning solution into the reservoir 21 Circulate the sanitizer solution for 10 minutes then push and release the Clean button 22 Allow the water system to be flushed of sanitizer for at least 20 minutes then push and release the Off button 23 Return the evaporator cover and front panel to their normal position and secure with the original fasteners 24 Push and release the On button to resume ice making Ice Storage Bin Remove and discard all ice Mix a solution of Scotsman Nickel Safe ice machine cleaner and wash all interior surfaces of the ice storage bin to remove any mineral scale build up Pour excess cleaner solution into the bin s drain Mix a solution of sanitizer and thoroughly wash all interior surfaces of the ice storage bin Pour excess sanitizer solution into the bin s drain November 2006 Page 21 C1448 C1848 C2148W Air and Water Cooled User Manual Air cooled condenser filter 1 Pull air filters from their louvered mounts 2 Wash the dust and grease off the filter 3 Return them to their original positions Do not operate the machine without the filter in place except during cleaning A vel T _
22. riginal plastic baffle Other Bins amp Applications Note the drop zone and ultrasonic sensor locations in the illustrations Scotsman ice systems are designed and manufactured with the highest regard for safety and performance They meet or exceed the standards of UL and NSF Scotsman assumes no liability of responsibility of any kind for products manufactured by Scotsman that have been altered in any way including the use of any part and or other components not specifically approved by Scotsman Scotsman reserves the right to make design changes and or improvements at any time Specifications and design are subject to change without notice November 2006 Page 3 C1448 C1848 C2148W Air and Water Cooled User Manual Product Description amp Electrical Requirements imensions Model Electrical Condensor Minimum Circuit a Fuse w x d x h Ampacity Size 48x24x29 C1448SA 32 208 230 60 1 C14485W 32 208 230 60 Ai 30 same c1eassa3 208 230603 ar 165 5 15 same C1848SW 3 208 230 60 3 Water 14 8 15 same C2148SW 32 208 230 60 1 Water 22 2 30 same C2148SW 3 208 230 60 3 Water 18 1 20 Table notes Medium cube models have the same electrical characteristics as Small Series revision code omitted Or HACR type circuit breakers This manual covers several models The model number on the product is located in two places on the back dataplate and on t
23. rim strip from the front until it snaps into place Return the front panel to its Original position and secure it to the cabinet Panel Removal November 2006 Page 8 Uncrate and Set Up C1448 C1848 C2148W Air and Water Cooled User Manual Begin with unpacking the ice storage bin Remove the carton and using part of the carton as a cushion tip the bin on its back to remove the skid and attach the legs or casters Note Turn the leg levelers in all the way and adjust after the ice machine is on top and in its selected location Return the bin to an upright position Check the bin top gasket for gaps and tears fill any in with food grade sealant prior to placing the ice machine on the bin Install the bin top adapter if one is required for the application If the ice machine has not been unpacked do so now Remove the carton from the skid Lift the ice machine off the skid directly onto the bin Note The machine is heavy Use a mechanical hoist if necessary Secure the ice machine to the bin with the hardware provided two metal straps and 4 bolts Level the bin and ice machine using the adjustment part of the legs Bin Recycling Many times an ice machine head will be replaced while the existing ice storage bin will be reused This is an acceptable practice if some precautions are taken e The used bin must be in
24. rvoir Allow the ice machine cleaner to circulate in the water system for at least 10 minutes Ice machine cleaner contains 4 CAUTION acids Acids can cause burns 8 Push and release the Clean button again The yellow Clean light will be on continuously and the machine will drain and refill the reservoir to flush out the ice machine cleaner and residue 9 Allow the drain and refill process to continue for at least 20 minutes 10 Push and release the Off button The clean cycle will stop and the display will show 3 Note If unit has not been de scaled for an extended period of time and significant mineral scale remains repeat steps 5 10 11 Mixa cleaning solution of 1 oz of ice machine cleaner to 12 ounces of water 12 Locate curtains push in on edge of curtain by pivot pin to release it Pull curtains out of machine Push Here LA DE i NI Da Pe If concentrated cleaner comes AJIA P lt in contact with skin flush with BI eo n water If swallowed do NOT M peel induce vomiting Give large amounts of water or milk Call Physician immediately Keep out of the reach of children November 2006 Page 20 13 Remove water distributors from ice machine Inspect each distributor for restricted orifice holes Be sure all holes are full open Squeeze Tabs Together Slide Out Until it Stops Then Lift to Remove
25. t 1 10 11 12 Is the unit located indoors in a controlled environment Is the unit located where it can receive adequate cooling air Has the correct electrical power been supplied to the machine Have all the water supply connections been made Have all the drain connections been made Has the unit been leveled Have all unpacking materials been removed Is the water pressure adequate Have the drain connections been checked for leaks Has the bin interior been wiped clean or sanitized Have any water filter cartridges been replaced Have all required kits and adapters been properly installed November 2006 Page 13 C1448 C1848 C2148W Air and Water Cooled User Manual Initial Start Up 1 Remove front panel Check machine for any packing or wires rubbing moving parts Note location of control board in upper left corner of the machines front 2 Remove tape securing each curtain to its evaporator 3 Switch on the electrical power to the machine Observe that some of the control s indicator lights glow and its display shows 4 Open the water supply valve 5 Push and release the ON button The indicator light will begin to blink F The flush valve will open and the water pump will start The inlet water valve will open to add water to the reservoir After a few seconds the flush valve will close and the water pump will stop Water will flow into the machine until the reservoir is full
26. with a power cord one must either be field installed or the machine hard wired The dataplate on the back of the cabinet details the power requirements including voltage phase minimum circuit ampacity and maximum fuse size HACR type circuit breakers may be used in place of fuses Extension cords are not permitted Use of a licensed electrician is recommended Electrical connections are made inside the junction box in the back panel of the ice machine 1 Remove the junction box cover and route the power cord through the access hole and P properly attach the power supply wires to the Supply leads in the junction box Wires 2 Installa field supplied strain relief per code Attach a ground wire to the ground connection in the junction box 3 Check voltage when complete 4 Return the junction box cover to its original position and secure with the original screws Follow all applicable local state and national codes November 2006 Page 12 x Ground Wire Connection Install Strain Relief Final Check List C1448 C1848 C2148W Air and Water Cooled User Manual After connections 1 Wash out the bin If desired the interior of the bin could be sanitized Locate the ice scoop if supplied and have it available for use when needed Final Check Lis
Download Pdf Manuals
Related Search