Schwinn A40(2011 model) Assembly Manual
Contents
1. 2 Attach Rail Assembly to Frame Assembly 3 Connect the Console Cable Note The cables must be fully connected for the Console to operate Do not crimp the Console Cable 4 Attach Console Mast to Frame Assembly Note Do not crimp the Console Cable 6mm 5 Attach Lower Handlebar Arms to Frame Assembly Note Only tighten this Hardware until secure 6 Attach Upper Handlebar Arms to Frame Assembly 7 Attach Pedal Arms to Frame Assembly Only tighten this Hardware until secure Note 8 Attach Legs to Frame Assembly 9 Attach Pedals to Legs 10 Attach Console to Frame Assembly Note Be sure the switch on the back of the Console is set to E The cables must be fully connected for the Console to operate Do not crimp the Console Cable Hardware is pre installed on Console and not on the Hardware Card 2 11 Attach Water Bottle Holder to Frame Assembly Hardware is pre installed and not on the Hardware Card 12 Tighten all Hardware Note Fully tighten all Hardware from the previous steps except where noted to only secure 13 Install Batteries in Console Note The console uses D size batteries LR20 which are not included Make sure that the batteries point in the direction of the indicators in the battery bay If you use rechargeable batteries the optional power adapter will not recharge the batter2. replacement parts and hardware Failure to use genuine replacement parts can cause a risk to users keep the machine from operating correctly and void the warranty Do not use the machine until it has been fully assembled and inspected for correct performance in accordance with the Owner s Manual Read and understand the complete Owner s Manual supplied with this machine before first use Keep the Owner s and Assembly Manuals for future reference Do all assembly steps in the sequence given Incorrect assembly can lead to injury Specifications and Tools Included Not Included 2 recommended 4mm bmm 6mm x2 64 163 cm recommended SS 59 150 cm 22 5 57 cm Parts 7 Front Stabilizer Leg Right Water Bottle Holder Leg Left Console Lower Left Handlebar Arm 1 T CCT FEA EE 3 QO J N OY 01 I amp J W I RO Hardware gt ao as 0 SD e A 6 Flat Head Hex Screw M8x25 Shaft B Button Head Hex Screw M8x15 Kk 6 Flat Washer M6 ra Flat Washer M8 Button Head Hex Screw M6x12 D spring Washer M8 2 Wave Washer Small D16 5 E Flat Washer Wide Sleeve Plastic G l Button Head Hex Screw M6x15 OP ft 4 Plastic Washer D16 2 H Carriage Bolt M6x25 oa 6 Washer Curved M0 INC CITI FE E Assembly Note Do not fully tighten the Hardware until the machine is completely assembled 1 Attach Front Stabilizer to Frame
3. the Machine The machine needs to be leveled if your workout area is uneven or if the Rail Assembly is slightly off the floor To adjust 1 Sl Be Oe N Place the machine in your workout area stand on the Rail Assembly for approximately 20 seconds step off of the machine Loosen the lock nut and adjust the levelers until they all contact the floor Adjust until the machine is level Tighten lock nuts 14 15 SCHWINN FITNESS Printed in China Nautilus Bowflex Schwinn Fitness Universal
4. SCHWINN FITNESS Schwinn A40 Elliptical Assembly Manual Verpagina2 PRS Ene CeCe litem eli Nautilus Bowflex Schwinn Fitness Universal 003 3790 060112 D Espa ol Americano Latino Para obtener este manual en Espa ol Latino Americano vaya a http www schwinnfitness com Table of Contents Before Assembly 2 Hardware 4 Important Safety Instructions 2 Assembly 4 Specifications and Tools 3 Adjustments 12 Parts 3 Nautilus Inc 800 NAUTILUS 800 628 8458 www Nautiluslnc com Customer Service North America 800 605 3369 customerserviceOschwinnfitness com Asia Pacific Latin America 360 859 5180 technics APLA nautilus com Patent information This product may be covered by US and Foreign Patents and Patents Pending See Product for more information Printed in China 2010 Nautilus Inc All rights reserved and indicate a trademark or registered trademark Nautilus Inc www NautilusInc com trademarks include NAUTILUSO BOWFLEX SCHWINN and UNIVERSALO and respective logos Other trademarks are the property of their respective owners Before Assembly select the area where you are going to set up and operate your machine For safe operation the location must be on a hard level surface Allow a workout area of minimum 70 5 x 107 179 cm x 272 cm Follow these basic points when you assemble your machine 2 d 4 D Read and understand the Important Safety Instruction
5. ies Do not mix old and new batteries Do not mix alkaline standard carbon zinc or rechargeable Ni Cd Ni MH etc batteries Final Inspection Inspect your machine to ensure that all fasteners are tight and components are properly assembled A Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner s Manual Optional Power Adapter The console for your machine can operate on battery power or AC power For AC power it is necessary to order the optional Power Adapter If batteries and the Power Adapter are installed the console will use the Power Adapter to operate Note If you use rechargeable batteries the optional Power Adapter will not recharge the batteries After the machine Is fully assembled connect the Power Adaptor to the console and the wall outlet NOTICE If you use a power adapter for your elliptical make sure that the cord stays clear of the path of the arms and pedals Attach the cord to the machine as shown NOTICE It is recommended to remove batteries when they are not used to avoid damage from battery corrosion To order the optional Power Adapter go to www schwinnfitness com powersupply Or call 1 800 605 3369 FCC Compliance Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
6. s before assembly Collect all the pieces necessary for each assembly step Using the recommended wrenches turn the bolts and nuts to the right clockwise to tighten and the left counterclockwise to loosen unless instructed otherwise When attaching 2 pieces lightly lift and look through the bolt holes to help insert the bolt through the holes The assembly requires 2 people Important Safety Instructions This icon means a potentially hazardous situation which if not avoided could result in death or serious injury Obey the following warnings Read and understand all warnings on this machine Carefully read and understand the Assembly Manual Keep bystanders and children away from the product you are assembling at all times Do not connect power supply to the machine until instructed to do so Do not assemble this machine outdoors or in a wet or moist location Make sure assembly is done in an appropriate work space away from foot traffic and exposure to bystanders Some components of the machine can be heavy or awkward Use a second person when doing the assembly steps involving these parts Do not do steps that involve heavy lifting or awkward movements on your own Set up this machine on a solid level horizontal surface Do not try to change the design or functionality of this machine This could compromise the safety of this machine and can void the warranty If replacement parts are necessary use only genuine Nautilus
7. user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e eorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Adjustments Moving the Machine A Do not move the machine without aid Injury to you or damage to the machine can occur Remove the power cord if equipped A the back of the Rail Assembly to carefully lift the machine onto the transport rollers Push the machine into position Carefully lower the machine into position Leveling
Download Pdf Manuals
Related Search