Sanyo VCC-6570P User's Manual
Contents
1. e If the backlight compensation function does not compensate properly for the conditions set using the LEVEL volume on the lens SETTINGS E White balance adjustment Normally the switch 8 WB is set to the down ATW auto white balance position and the white balance is adjusted automatically If a manual white balance adjustment is necessary follow the steps below Set the switch 8 WB to the up M manual position then adjust the colour e Turn RED VR302 to set the red ratio and or BLUE VR303 to set the blue ratio VR302 VR303 t RED B L u 8 E Synchronization settings The default setting is internal synchronization INT You can change the power supply synchronization by moving switch 9 to the up LL position Refer to Line phase adjustment for details E Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor there may be a vertical roll of the images when switched In such a case set as described below 1 Set the switch 9 SYNC to the up LL position 2 Switch the display on the monitor from camera 1 to camera 2 Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops H more than two cameras are used please repeat this procedure for all the cameras AS LG og el EE Zeg CAUTION If the vertical roll cannot be corrected by setting the LINE PHASE volume on camera 2 try setting the LINE PHASE v2. Sanyo Electric Co Ltd 1AC6P1P2453 Printed in Japan L53T5 XE 0801KPS DSP
3. 1 FEATURES e Built in interline transfer method 1 3 CCD approx 470 000 picture elements e Equipped with a DSP Digital Signal Processor function e Horizontal resolution more than 520 TV lines e High sensitivity minimum required illumination is 1 0 lux F1 2 e Two types of backlight compensation functions multi spot photometry and center focus photometry e Low smear anti blooming low lag no burning and no geometric distortion using the CCD solid state image device 100 solid state components giving excellent immunity to shock and vibration e Not subject to interference from magnetic or electrostatic fields e Power supply 220 230 V AC operation PRECAUTIONS HB Incase of problem Do not use the camera if smoke or a strange odour comes from the unit or if it seems not to function correctly Disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Centre HB Do not open or modify Do not open the cabinet as it may be dangerous and cause damage to the unit For internal settings and repairs consult your dealer or a Sanyo Authorized Service Centre E Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the camera If used with a foreign object inside it could cause a fire short circuits or damages If water or a liquid gets inside the camera disconnect the power cord immediately and consult your dealer or a Sanyo Auth
4. C mount adaptor option on the lens mount then carefully align the lens mount with the camera opening and turn the lens slowly to install it CS mount 3 Connect the lens plug to the lens iris output connector LENS on the side of the camera type lens When using lenses from other makers the plug shape may not correspond to the terminal on the camera In such a case remove the original plug and using a soldering iron connect the supplied lens iris plug according to the diagram Refer to page 8 NOTE When using an auto iris lens the supplied clamping core C must be installed on the lens wire in order to prevent electromagnetic interference to the other devices connected English 7 MOUNTING THE LENS E Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable Cut the cable at the plug then remove approx 8 mm of the cable sheath and strip about 2 mm from each wire 2 Install the lens iris plug Solder the cable to the pins following the correct pin layout refer to the table and illustrations then close the plug cover Pin layout DC type lenses VIDEO type lenses Brake coil 12 V DC 50 mA max Brake coil Not used Drive coil Video output 1 0 Vp p high impedance E Flange back adjustment Drive coil Ground for video signal and DC power If the pick up surface is not correctly positioned with relation to the lens focal point the picture w
5. smear phenomenon effect oo e If conditions are outside the electronic iris operation range or 123 more than the maximum illumination it will cause saturation of the CCD In that case use a manual iris lens Unit sec E Aperture The initial setting for switch 5 is up SHRP so that the contours of the object are emphasized However if the contours of the object are already emphasized more than required set switch 5 to the down NOR position 5 12 English SETTINGS E Backlight compensation setting This camera has two different backlight compensation functions Normally backlight compensation switch 6 MULT and 7 CENT Lt lt are set to the down OFF position Change the backlight compensation switch settings 6 7 depending on the conditions e MULT mode Use this position when applying backlight compensation to the whole of the screen e CENT mode Use this position when applying backlight compensation to only the central portion of the screen Note e If switches 6 and 7 are set to the up ON position at the same time the MULT setting will have priority e When MULT mode is set scenes with no backlighting may appear extremely dark and the object may appear over exposed If this happens set to CENT mode English 13 MULTI mode 64 sections If using a VIDEO type auto iris lens e The ALC volume on the lens should be turned all the way to Av Average
6. AL Hi VIDEO type auto iris lens cra A lens with amplifier circuit that operates on video signal and DC power source In general this type of lens is referred to as EE amplifier type lens ALC and LEVEL volume level controls are available on the lens for iris adjustments Set the A I LENS switch to the VIDEO position HE Compatible auto iris lenses 1 3 inch Sanyo DC type lens VIDEO type lens VCL CS8LY Standard angle f 8 mm Standard angle f 9 mm VCL CS4LY Wide angle f A mm Telephoto angle f 12 mm VCL CS2LY Ultra wide angle f 2 8 mm Greater telephoto angle f 16 mm E If using a VIDEO type auto iris lens e Set the ALC and LEVEL controls on the lens to adjust the iris Normally the ALC volume should be turned all the way to Av Average e Depending on the type of lens used the lens may not perform properly In such a case adjust the LEVEL volume on the lens casing to correct 6 English MOUNTING THE LENS Please use a DC type auto iris lens sold separately Check the lens mount Do not use a lens if the length L is more than 5 mm That may damage the camera and prevent proper installation Remove the lens mount cap from the camera Install the auto iris lens CS mount type lens Carefully align the lens mount with the camera opening then turn the lens slowly to install it C mount type lens To allow for flange back adjustment install the
7. C 2V 250 m maximum e Cable type RG 6U 5C 2V 500 m maximum e Cable type RG 11U 7C 2V 600 m maximum CAUTION e The RG 59U type cable should not be run through electrical conduits or through the air e Using CCTV Video grade coaxial cable CONNECTIONS A Connections to the camera Y C OUT connector The peripheral devices VCR monitor lens etc and cables are sold separately 1 Using a coaxial cable twin type 75 ohms connect the Y C OUT connector from the camera to the S VIDEO input terminal on the monitor or time lapse VCR When using this unit the supplied clamping core A and B must be installed on the power cord and BNC cable in order to prevent electromagnetic interference to the other devices connected Insert the plug of this power cord into a wall outlet Then turn on the power of all the devices connected to the camera The POWER indicator A will light Adjust the picture on the monitor using the Brightness and Contrast controls re d D gt p gt gt T Video signal connections p gt gt VIDEO IN D VIDEO OUT CAUTION e Please use a monitor with a Y C or S VIDEO input terminal or a time lapse VCR with a S VIDEO input terminal Use a Mini DIN round type 4 pin plug to connect to the Y C connector Never use a coaxial cable longer that 10 metres to connect the camera to the S VIDEO input terminal 10 English SETTINGS The ill
8. E High speed electronic shutter setting E Iris function setting Normally the speed setting switches for the high speed electronic This should normally be set to the down Al position t shutter are all set to the down OFF position This sets the electronic Use a manual or fixed iris lens and set the lens aperture shutter speed to 1 50 sec The switches can be set as indicated in to the shortest F stop Set the switch 4 IRIS to the up 4 table A to select one of the 8 speeds available El position CAUTION IS When using an auto iris lens for indoor outdoor use e When using the high speed electronic shutter the switch 4 must Set the switch 4 IRIS to the down Al position be set to the down Al position Using the high speed electronic shutter indoors with low lighting Note will give darker pictures In such a case add some lights to make e The electronic iris is suitable for normal indoor use When the switch sure the lighting is sufficient If the lighting is very bright pay 4 IRIS is set to the up El position do not use an auto iris lens attention to the light angle in order to avoid or minimize the e H used under fluorescent light the image may flicker In such a smear phenomenon effect case change to incandescent lighting or set the switch 4 IRIS to Table A switch 1 3 the down Al position and use an auto iris lens e When shooting bright subjects pay attention to the light angle in 1 500 order to avoid or minimize the
9. NGE BACK LOCK Camera installation bracket The bracket can be fixed at the top or bottom of the camera When fixing the bracket be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings CAUTION When installing the camera support select a location that can support the total weight of the camera and accessories Shorter screws M3 x 4 Longer screws M3 x 6 Camera mounting screw hole 1 4 20 UNC 4 English PARTS NAMES Lens iris output connector LENS This 4 pin connector is used to send the DC control signal and power supply to an auto iris type lens Camera setup section under the cover These settings are for when using a 1 3 inch CS mount DC without EE internal amplifier type lens However if due to installation conditions or environment the settings may need to be modified for best results see SETTINGS To access the controls remove the cover fixing screw then remove the cover NOTE When using a 1 2 or 2 3 inch C mount VIDEO with EE internal amplifier auto iris type lens set the AL LENS switch to the VIDEO position English 5 CONCERNING AUTO IRIS LENSES Hi DC type auto iris lens Vaso A lens without amplifier circuit that operates only on a DC power source In general this type of lens is referred to as DC type coil lens or DC type non amplifier lens DC Set the A I LENS switch to the DC position VIDEO
10. SANYO INSTRUCTION MANUAL VCC 6570P BEDIENUNGSANLEITUNG MANUEL D INSTRUCTIONS FA RAH COLOUR CCD camera CCD Farbkamera Cam ra CCD COULEUR f amp CCD KA About this manual A propos de ce manuel Before installing and using the camera please read this Avant d installer et d utiliser la cam ra veuillez lire ce manual carefully Be sure to keep it handy for later reference manuel attentivement Gardez le a port e de main pour toute r f rence ult rieure Uber diese Bedienungsanleitung AT ARAB Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der E LE Be EF EBL Z BU Ir ANP GA II BBS Kamera zuerst diese Bedienungsanleitung sorgfaltig durch und BBR IE ACE AHAB DL SJ Eee bewahren Sie sie zum sp teren Nachschlagen auf Depending on the conditions of use installation and environment please be sure to make the appropriate settings and adjustments If you need help with installation and or settings please consult your dealer CONTENTS US UK H PARTS NAMES iiia n naaa a a CONCERNING AUTO IRIS LENSES MOUNTING THE LENS sssssssssssssennnnrnnnnunnernnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnrnnne CONNECTIONS csssssssssstssssstsssstessssessseesssesssseesssseessssssssseesssseessaseessass 9 KUCKE 11 TROUBLESHOOTING sscsssssssssssssssssssssesssssssssssssseessseesssieesssessans 16 dl UI 17 ACCESSORIES Lens iris plug pm d PC Clamping core A J PC English
11. companying instructions Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time as that may cause damage or paint peeling HSITDNA 2 English PARTS NAMES English A Power indicator POWER Comes on when the power to the camera is on Video output connector VIDEO OUT BNC type Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector AC power cord External sync composite video signal input connector VBS IN BNC type Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite signal of a video distributor Line phase adjustment volume LINE PHASE When using two cameras or more the image on the monitor may roll vertically when switching sources This rolling can be minimized by turning this volume Y C OUT connector 4 pin Separate Y luminance and C chroma signals are output from this terminal A better picture quality is obtained if the monitor or VCR is connected to this connector Y signal ground C signal ground Y signal 1 0 Vp p 75 ohms unbalanced negative sync C signal 0 3 Vp p 75 ohms unbalanced PARTS NAMES Lens mount cap The cap is installed to protect the lens mount section Remove the lens mount cap before installing a lens sold separately Flange back adjustment screw FLANGE BACK ADJ Flange back lock screw FLA
12. ill be out of focus in particular when using auto iris power zoom lenses sold separately If that is the case adjust the flange back position as described below 1 Using a screwdriver loosen the FLANGE BACK LOCK screw M2 Set the zoom lens to the maximum telephoto position set the focus using the focus ring on the lens 2 3 Set the zoom lens to the maximum wide angle position set the focus using the FLANGE BACK ADJ screw 4 Repeat steps 2 and 3 until the image stays in focus when changing from a telephoto shot to a wide angle shot When the setting is complete tighten the FLANGE BACK LOCK screw 8 English CONNECTIONS lt A D I 1 lt 4 1 D Pe Video signal connections gt gt gt VIDEO IN D VIDEO OUT Basic connection for monitoring or recording The peripheral devices VCR monitor lens etc and cables are sold separately 1 Make the video signal connection between the camera and the monitor or time lapse VCR 2 When using this unit the supplied clamping core A and B must be installed on the power cord and BNC cable in order to prevent electromagnetic interference to the other devices connected 3 Insert the plug of this power cord into a wall outlet The POWER indicator A will light Adjust the picture on the monitor using the Brightness and Contrast controls etc English 9 HB Coaxial cable type and maximum length e Cable type RG 59U 3
13. imum required illumination incandescent lighting Backlight compensation Iris function Electronic iris range Electronic shutter Flange back White balance Lens mount English 17 PAL standard PLL 2 1 interlace 1 3 inch solid state image device CCD 795 H x 596 V Effective picture elements Environmental conditions 625 TV lines 25 frames sec Power supply Power consumption 752 H x 582 V Weight Internal sync Line lock manually switchable External sync 520 TV lines horizontally 400 TV lines vertically 1 0 Vp p 75 ohms composite Y Video 0 7 Vp p sync 0 3 Vp p 75 ohms C Burst 0 3 Vp p 75 ohms More than 48 dB Approx 1 0 lux with a F 1 2 lens Manual ON OFF switching MULT CENT switching Active when using an auto iris lens Manual EA switching 1 0 lux to 50 000 lux F 1 2 lens 8 speeds selectable by switches 1 50 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 sec 12 5 mm 0 5 mm ATW Manual switching CS mount Temperature 10 C 50 C Humidity less than 90 no condensation 220 230 VAC 10 50 Hz Approx 4 0 W with auto iris lens Approx 3 0 W without auto iris lens Approx 620 g without lens SPECIFICATIONS HE Dimensions ESE 1 4 20 UNC 22 Features and specifications are subject to change without prior notice or obligations 18 English SANYO
14. olume on camera 1 If it still cannot be corrected please check that the polarity of the power cords of all connected devices is correct 14 English SETTINGS E External sync adjustment VBS 1 Connect the VBS signal output for the other camera to the VBS IN connector at the rear of this camera 2 If the signals are not synchronized change the sub carrier SC P1 switches as follows Setting 9 pin Default OFF down Set to 90 counterclockwise OFF Set to 180 counterclockwise ON Set to 270 counterclockwise ON Roi Note e The sub carrier switches let you make broad adjustments to the sub carrier phase If finer adjustments are required contact the place of purchase e The type and length of the cable which is connected to the VBS connector may cause the horizontal synchronization being out of phase If this happens adjust VR304 H P horizontal sync English 15 E Lens iris adjustment If using a DC type auto iris lens you will need to set the LEVEL VR301 volume when shooting in the conditions described below VR301 LEVEL L counterclockwise To decrease the contrast H clockwise To increase the contrast e If shooting simultaneously in a dark room and through a bright window e If the subject background is extremely bright or dark e If the brightness of the picture on the monitor is not correct TROUBLESHOOTING Before taking the came
15. orized Service Centre Be careful to protect the camera from rain sea water etc W Be careful when handling the unit To prevent damages do not drop the camera or subject it to strong shock or vibration W Install away from electric or magnetic fields If installed close to a TV radio transmitter magnet electric motor transformer audio speakers the magnetic field they generate will distort the image HB Protect from humidity and dust To prevent damages to the camera do not install it where there is greasy smoke or steam where the dampness may get too high or where there is a lot of dust E Protect from high temperatures Do not install close to stoves or other heat generating devices such as spotlights etc or where it could be subject to direct sunlight as that could cause deformation discoloration or other damages Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may raise to high levels Install where the temperature range will stay between 10 C and 50 C no condensation E Cleaning e Dirt can be removed from the cabinet by wiping it with a soft cloth To remove stains wipe with a soft cloth moistened with a soft detergent solution and wrung dry then wipe dry with dry soft cloth Do not use benzine thinner or other chemical product on the cabinet as that may cause deformation and paint peeling Before using a chemical cloth make sure to read all ac
16. ra for repairs please check below to make sure that the camera is used correctly If it still does not perform correctly please consult your dealer or a Sanyo Authorized Service Centre E No picture on the monitor screen e Is the power turned on to all connected devices Is the voltage correct e Are all the signal connecting cables correctly connected e Is the lighting sufficient e Has the lens cap been removed e Is the lens type DC or VIDEO correctly selected Depending on the type of lens the A I LENS switch must be set accordingly e Is the iris control correctly set Lo E The picture is not clear e Is the monitor correctly adjusted e Is the flange back position correctly set e Is the lens focus correctly adjusted e Are the lens surfaces clean If there is dust or finger prints on the lens the image quality will deteriorate To clean the lens use a soft cloth or a commercially available lens cleaning set SERVICE This camera is a precision instruments and if treated with care will provide years of satisfactory performance However in the event of a problem the owner is advised not to attempt to make repairs or open the cabinet Servicing should always be referred to your dealer or Sanyo Authorized Service Centre 16 English SPECIFICATIONS E Camera Scanning system Interlace Image device Picture elements Synchronizing system Resolution Video output level Y C signal outputs Video S N ratio Min
17. ustration shows the factory default settings for the switches in the camera setup section The camera settings are described on the assumption that a DC type auto iris lens is being used If you are using a VIDEO type auto iris lens be sure to read the Note which is given Control name Position High speed electronic shutter setting 1 50 sec Electronic Iris El Auto iris Al setting Al Aperture compensation setting SHRP Sharp SHRP Normal NOR Backlight compensation setting BLC OFF MULT OFF Backlight compensation setting BLC OFF CENT OFF White balance switch M ATW and colour ATW R or B adjustment volume External sync setting SYNC LL INT INT VR302_ _VR303 RED ES IRIS AP BLC WE E SHRP CENT 1 2 31 MULT M ON merw 1234567 8 MSB LSB A OFF __ATWyscysyn NOR OFF External sync setting SC P1 adjustable External sync horizontal adjustment H P adjustable Auto iris lens setting A I LENS see page 6 DC Lens iris level adjustment adjustable 9 68 1009 00o English 11 SETTINGS
Download Pdf Manuals
Related Search