Sanyo VCC-4594 User's Manual
Contents
1. t When using an auto iris lens for indoor outdoor use Set the switch 1 IRIS to the down Al position Note e The electronic iris is suitable for normal indoor use When the switch 1 IRIS is set to the up El position do not use an auto iris lens e If used under fluorescent light the image may flicker In such a case change to incandescent lighting or set the switch 1 IRIS to he down Al position and use an auto iris lens e When shooting bright subjects pay attention to the light angle in order to avoid or minimize the smear phenomenon effect e If conditions are outside the electronic iris operation range or more than the maximum illumination it will cause saturation of he CCD In that case use a manual iris lens E Aperture If you would like to emphasize the contours of the object set the switch 2 AP to the up SHRP position At 12 English SETTINGS E Backlight compensation setting This camera has two different backlight compensation functions Normally backlight compensation switch 3 MULT and 4 CENT Lt lt are set to the down OFF position Change the backlight compensation switch settings 3 4 depending on the conditions e MULT mode Use this position when applying backlight compensation to the whole of the screen e CENT mode Use this position when applying backlight compensation to only the central portion of the screen Note e If switches 3 and 4 are set to the up ON2. 8 mm Standard angle f 9 mm VCL CS4LY Wide angle f 4 mm Telephoto angle f 12 mm VCL CS2LY Ultra wide angle f 2 8 mm More telephoto angle f 16 mm W If using a VIDEO type auto iris lens e Set the ALC and LEVEL controls on the lens to adjust the iris Normally the ALC volume should be turned all the way to Av Average e Depending on the type of lens used the lens may not perform properly In such a case adjust the LEVEL volume on the lens casing to correct 6 English FLANGE BACK ADJUSTMENT Flange back lock screw Fig 1 English 7 If the pick up surface is not correctly positioned with relation to the lens focal point the picture will be out of focus in particular when using auto iris power zoom lenses sold separately If that is the case adjust the flange back position as described below 1 Using a screwdriver loosen the flange back lock screw M2 2 Set the zoom lens to the maximum telephoto position set the focus using the focus ring on the lens 3 Set the zoom lens to the maximum wide angle position set the focus using the flange back adjustment lever 4 Repeat steps 2 and 3 until the image stays in focus when changing from a telephoto shot to a wide angle shot When the setting is complete tighten the flange back lock screw Note When flange back lock screw is completely tighten it will protrude slightly as shown in the illustratio
3. PARTS NAMES 3 Flange back lock screw Lens mount cap The cap is installed to protect the lens mount section Remove the lens mount cap before installing a lens sold separately Flange back adjustment lever See page 7 Camera installation bracket The bracket can be fixed at the top or bottom of the camera When fixing the bracket be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings Shorter screws M3 x 4 Longer screws M3 x 6 Camera mounting screw hole 1 4 20 UNC CAUTION When installing the camera support select a location that can support the total weight of the camera and accessories English 5 CONCERNING AUTO IRIS LENSES DC VIDEO A I LENS E DC type auto iris lens A lens without amplifier circuit that operates only on a DC power source In general this type of lens is referred to as DC type coil lens or DC type non amplifier lens Set the A I LENS switch to the DC position E VIDEO type auto iris lens A lens with amplifier circuit that operates on video signal and DC power source In general this type of lens is referred to as EE amplifier type lens ALC and LEVEL volume level controls are available on the lens for iris adjustments Set the A I LENS switch to the VIDEO position Hi Compatible auto iris lenses 1 3 inch Sanyo DC type lens VIDEO type lens VCL CS8LY Standard angle f
4. position at the same time the MULT setting will have priority e When MULT mode is set scenes with no backlighting may appear extremely dark and the object may appear over exposed If this happens set to CENT mode English 13 MULTI mode 64 sections CENT mode If using a VIDEO type auto iris lens The ALC volume on the lens should be turned all the way to Av Average e If the backlight compensation function does not compensate properly for the conditions set using the LEVEL volume on the lens SETTINGS E White balance adjustment Normally the switch 5 WB is set to the down ATW auto white balance position and the white balance is adjusted automatically If a manual white balance adjustment is necessary follow the steps below Set the switch 5 WB to the up M manual position then adjust the colour e Turn RED VR302 to set the red ratio and or BLUE VR303 to set the blue ratio VR303 VR302 t 5 BLUE D Synchronization settings The default setting is internal synchronization INT You can change the power supply synchronization by moving switch 6 to the up LL position Refer to Line phase adjustment for details E Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor there may be a vertical roll of the images when switched In such a case set as described below 1 Set the switch 6 SYNC to the up LL position 2 Swi
5. cover Pin layout DC type lenses VIDEO type lenses Brake coil 12 V DC 50 mA max 2f a Brake coil Not used ots Drive coil Video output 1 0 Vp p high impedance 4 Drive coil Ground for video signal and DC power English 9 CONNECTIONS on SA h if I lt 1 Video signal connections p gt gt VIDEO IN SS gt VIDEO OUT Basic connection for monitoring or recording The peripheral devices VCR monitor lens etc and cables are sold separately 1 Make the video signal connection between the camera and the monitor or time lapse VCR 2 Connect to 24 V AC UL listed class 2 power supply CAUTION To prevent camera and or power supply failure pay close attention to polarity when making the connections e To prevent fire hazard any UL listed wire rated VW 1 should be used for the 24 V AC cable input terminal 3 Insert the plug of this power cord into a wall outlet The POWER indicator A will light Adjust the picture on the monitor using the Brightness and Contrast controls HB Coaxial cable type and maximum length e Cable type RG 59U 3C 2V 250 m maximum e Cable type RG 6U 5C 2V 500 m maximum e Cable type RG 11U 7C 2V 600 m maximum CAUTION e The RG 59U type cable should not be run through electrical conduits or through the air e Using CCTV Video grade coaxial cable 1
6. 0 English SETTINGS The illustration shows the factory default settings for the switches in the camera setup section The camera settings are described on the assumption that a DC type auto iris lens is being used If you are using a VIDEO type auto iris lens be sure to read the Note which is given Furthermore refer to the sticker on the inside of the cover for details on DIP switch positions Control name Position Color and Black White level switch C BW L VR303 VR302 BLUE R CBW IRIS AP BLC WB O E SHRP CENT SC Pi English 11 VR301 DC VIDEO A I LENS Electronic Iris El Auto iris Al setting Al Aperture compensation setting Sharp SHRP Normal NOR Backlight compensation mode setting MULT OFF Backlight compensation setting BLC CENT OFF White balance switch WB and color R or B adjustment volume External sync setting SYNC LL INT Auto iris lens setting A I LENS see page 6 DC Lens iris level adjustment adjustable SETTINGS E Iris function setting This should normally be set to the down Al position Use a manual or fixed iris lens and set the lens aperture to the shortest F stop Set the switch 1 IRIS to the up El position At
7. R IMPLIED WITH REGARD TO THIS PRODUCT INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL SFC S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER ARISING OUT OF OR IN CONNECTION WITH THE SALE USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR S NEGLIGENCE ALLEGED DAMAGED OR DEFECTIIVE GOODS WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT ATTENTION For your protection in the event of theft or loss of this product please fill in the information below for you own personal records Model No Serial No Located on back or bottom side of unit Date of Purchase Purchase Price Where Purchased SANYO 21605 Plummer Street 1AC6P1P2420 Chatsworth California 91311 L53Z4 US 0401KP DSP Printed in Japan
8. SANYO INSTRUCTION MANUAL VCC 4594 COLOR CCD CAMERA DAY NIGHT About this manual Before installing and using the camera please read this manual carefully Be sure to keep it handy for later reference Depending on the conditions of use installation and environment please be sure to make the appropriate settings and adjustments If you need help with installation and or settings please consult your dealer CONTENTS INFORMATION TO USER ssssssssssstssssssessssessstsssssesssseessssessssiessssiensesse PRECAUTIONS cccssssssssssssssssesssssssstessstessseessssesssseesssesssssessssiessssiensans PARTS NAMES aieia ainaani aaeain CONCERNING AUTO IRIS LENSES ssssssssrsrssnnnrnrensunnnnrnnnnnnnnnnnnnnnnnnes FLANGE BACK ADJUSTMENT as MOUNTING THE LENS ssssssssstesssstessssssssstesssmesssieesssieessiesssseessssiens CONNECTIONS sscssssssssssssssssstssssssesssseessseessstesssseesssseesssseessseesssseessaaes SETTINGS inaianei inanakan aviaire Saans TROUBLESHOOTING ssssssssstsssssssssssssesssssesssseesssiessssessssesssssesssaues SPECIFICATIONS English 1 FEATURES The optical filter is switched automatically to color image or black and white image according to the subject brightness e Built in interline transfer method 1 3 CCD approx 410 000 picture elements e Low smear anti blooming low lag no burning and no geometric distortion using the CCD solid state image device e 100 solid stat
9. ctly If it still does not perform correctly please consult your dealer or a Sanyo Authorized Service Centre E No picture on the monitor screen e Is the power turned on to all connected devices Is the voltage correct e Are all the signal connecting cables correctly connected e Is the lighting sufficient e Has the lens cap been removed e Is the lens type DC or VIDEO correctly selected Depending on the type of lens the A I LENS switch must be set accordingly e ls the iris control correctly set A When using a DC type lens the LEVEL volume inside the camera casing should be adjusted B When using a VIDEO type lens the LEVEL volume on the lens should be adjusted E The picture is not clear e Is the monitor correctly adjusted e Is the flange back position correctly set e Is the lens focus correctly adjusted e Are the lens surfaces clean If there is dust or finger prints on the lens the image quality will deteriorate To clean the lens use a soft cloth or a commercially available lens cleaning set 16 English SPECIFICATIONS E Camera Scanning system Interlace Image device Picture elements Effective picture elements Synchronizing system Resolution Video output level Video S N ratio Minimum required illumination incandescent lighting Control terminal Backlight compensation Iris function Electronic iris range Flange back White balance Lens mount English 17 NTSC stan
10. d below SFC will repair or replace at its option the product and any of its parts which fail to conform to this warranty The warranty period commences on the date the product was first purchased or rented at retail LABOR PARTS IMAGE DEVICE 3 YEARS 3 YEARS 3 YEARS EXCLUSIONS This warranty does not cover A the adjustment of customer operated controls as explained in the appropriate model s instruction manual or B the repair of any product whose serial number has been altered defaced or removed This warranty shall not apply to the cabinet or cosmetic parts batteries or routine maintenance This warranty does not apply to uncrating setup installation removal of the product for repair or reinstallation of the product after repair This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including but not limited to any malfunction defect or failure caused by or resulting from unauthorized service or parts improper maintenance operation contrary to furnished instructions shipping or transit accidents modification or repair by the user abuse misuse neglect accident incorrect power line voltage fire flood or other Acts of God or normal wear and tear The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS O
11. dard TV system 525 TV lines 30 frames sec PLL 2 1 interlace 1 3 inch solid state image device CCD 811 H x 508 V 768 H x 494 V Internal sync Line lock manually switchable 520 TV lines horizontally 350 TV lines vertically 1 0 Vp p 75 ohms composite More than 48 dB Approx 0 03 lux with a F 1 2 lens B W mode Approx 0 6 lux with a F 1 2 lens color mode anual color black and white setting anual ON OFF switching Multi zone light measuring system Active when using an auto iris lens Manual ON OFF switching 0 6 lux to 35 000 lux F 1 2 lens color mode 1 0 lux to 50 000 lux F 1 4 lens color mode 12 5 mm 0 5 mm ATW Manual switching CS mount or C mount with the supplied adaptor Environmental conditions Power supply Power consumption Temperature 10 C 50 C Humidity less than 90 no condensation 24 V AC 60 Hz 3 8 W with auto iris lens 2 9 W without auto iris lens Weight Approx 450 g without lens HE Dimensions mm 7 136 z _ 67 ee 126 5 111 15 4 25 2 N 1 4 20 UNC Features and specifications are subject to change without prior notice or obligations SERVICE This camera is a precision instruments and if treated with care will provide years of satisfactory performance However i
12. e components giving excellent immunity to shock and vibration e Not subject to interference from magnetic or electrostatic fields e High sensitivity minimum required illumination is 0 03 lux F1 2 B W mode e Horizontal resolution more than 520 TV lines Power supply 24 V AC operation ACCESSORIES JLens inis plug 4 pin e2e csekeden occa ee ante ee nets acceded pO INFORMATION TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT WARNING TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE For the customers in Canada This Class B digital apparatus complies with Canadian ICES 003 Pour la client le canadienne Cet appareil numerique de la Classe B est conforme a la norme NMB 003 du Canada This installation should be made by a qualified service person and should conform to all local codes This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee
13. n Fig 1 Do not tighten the screw further MOUNTING THE LENS C mount type lens 2 CS mount type lens Please use a DC type auto iris lens sold separately Checking the lens mount Do not use a lens if length L is more than 5 mm If not that may damage the camera and prevent proper installation Remove the lens mount cap from the camera Install the auto iris lens CS mount type lens Carefully align the lens mount with the camera opening then turn the lens slowly to install it C mount type lens To allow for flange back adjustment install the C mount adaptor option on the lens mount then carefully align the lens mount with the camera opening and turn the lens slowly to install it Connect the lens plug to the lens iris output connector LENS on the side of the camera When using lenses from other makers the plug shape may not correspond to the terminal on the camera In such a case remove the original plug and using a soldering iron connect the supplied lens iris plug according to the diagram Refer to page 9 8 English MOUNTING THE LENS E Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable Cut the cable at the plug then remove approx 8 mm of the cable sheath and strip about 2 mm from each wire 2 Install the lens iris plug Solder the cable to the pins following the correct pin layout refer to the table and illustrations then close the plug
14. n the event of a problem the owner is advised not to attempt to make repairs or open the cabinet Servicing should always be referred to your dealer or Sanyo Authorized Service Centre SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user s expense unless specifically stated otherwise in this warranty The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll free number listed below For product operation authorized service center referral service assistance or problem resolution call CUSTOMER INFORMATION 1 800 421 5013 Weekdays 8 30 AM 5 00 PM Pacific Time For accessories and or parts call PARTS ORDER INFORMATION 1 800 726 9662 Weekdays 8 30 AM 5 00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA EXCLUDING ALL U S TERRITORIES AND PROTECTORATES THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END USER THE ORIGINAL DATED BILL OF SALE SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED Subject to the OBLIGATIONS above and EXCLUSIONS below SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specifie
15. ng it with a soft cloth To remove stains wipe with a soft cloth moistened with a soft detergent solution and wrung dry then wipe dry with dry soft cloth Do not use benzine thinner or other chemical product on the cabinet as that may cause deformation and paint peeling Before using a chemical cloth make sure to read all accompanying instructions Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time as that may cause damage or paint peeling PARTS NAMES Power indicator POWER a Comes on when the power to the camera is on Video output connector VIDEO OUT BNC type wie Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector gog gesce Manual color black and white setting terminal CONTROL GCB au ek e G ground terminal e C color terminal e B black and white terminal Line phase adjustment volume LINE PHASE When using two cameras or more the image on the monitor may roll vertically when switching sources This rolling can be minimized by turning this volume 24 V AC input terminal 24 V AC GND Camera setup section under the cover If due to installation conditions or environment the settings may need to be modified for best results see SETTINGS To access the controls loosen the cover fixing screw then remove the cover Lens iris output connector LENS 4 English
16. not put objects inside the unit ake sure that no metal objects or flammable substance get inside he camera If used with a foreign object inside it could cause a fire short circuits or damages f water or a liquid gets inside the camera disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Centre Be careful to protect the camera from rain sea water etc W Be careful when handling the unit To prevent damages do not drop the camera or subject it to strong shock or vibration W Install away from electric or magnetic fields If installed close to a TV radio transmitter magnet electric motor transformer audio speakers the magnetic field they generate will distort the image English 3 E Protect from humidity and dust To prevent damages to the camera do not install it where there is greasy smoke or steam where the dampness may get too high or where there is a lot of dust E Protect from high temperatures Do not install close to stoves or other heat generating devices such as spotlights etc or where it could be subject to direct sunlight as hat could cause deformation discoloration or other damages Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may raise to high levels nstall where the temperature range will stay between 10 C and 50 C no condensation E Cleaning e Dirt can be removed from the cabinet by wipi
17. tch the display on the monitor from camera 1 to camera 2 Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops If more than two cameras are used please repeat this procedure for all the cameras CAUTION If the vertical roll cannot be corrected by setting the LINE PHASE volume on camera 2 try setting the LINE PHASE volume on camera 1 If it still cannot be corrected please check that the polarity of the power cords of all connected devices is correct 14 English SETTINGS E Lens iris adjustment If using a DC type auto iris lens you will need to set the LEVEL VR301 volume when shooting in the conditions described below VR301 LEVEL L counterclockwise To decrease the contrast H clockwise To increase the contrast e If shooting simultaneously in a dark room and through a bright window e If the subject background is extremely bright or dark e If the brightness of the picture on the monitor is not correct English 15 E C B W color black and white switch setting This switch lets you select the timing of the automatic switching of the optical filter to color image or black and white image according to the subject brightness The default setting is L Set the switch according to the brightness C BW Fig 2 H for a brighter setting than L L Standard setting Notes e After the power has been t
18. that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by Sanyo may void the user s authority to operate this camera 2 English PRECAUTIONS E Incase of problem Do not use the camera if smoke or a strange odour comes from the unit or if it seems not to function correctly Disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Centre E Do not open or modify Do not open the cabinet as it may be dangerous and cause damage o the unit For internal settings and repairs consult your dealer or a Sanyo Authorized Service Centre E Do
19. urned off switching will restart from color when the power is restored e A sound may be heard when the color image or black and white image is switched Also the image will be distorted as shown in Fig 2 this is normal and does not indicate a problem e When using infrared lighting if there is a strong reflection on the subject the optical filter may switch from black and white to color mode Use only enough infrared lighting so that the mode is not switched e The focus setting may be different in black and white mode and color mode Please check the focus setting in both modes SETTINGS WE Manual color black and white setting Connect each pin of the CONTROL terminal as indicated below to set the image to black and white or color as desired e Color image setting Connect the C color and the G ground pins e Black and white setting Connect the B black and white and the G ground pins CONTROL terminal z 5 Image OFF OFF Auto OFF ON Black and white ON OFF color ON ON Auto ON Close OFF Open Notes e The maximum length of cable for CONTROL terminal is 600 m AWG 24 e During optical filter switching even if the manual switching operation is done you cannot determine if the image is black and white or color Manual switching will have to be done one more time TROUBLESHOOTING Before taking the camera for repairs please check below to make sure that the camera is used corre
Download Pdf Manuals
Related Search