Sanyo KS2432 User's Manual
Contents
1. 60 F min The temperature setting changes by two degrees each time the button is pressed The air conditioner remembers the new temperature setting even when it is turned off STEP 4 Set the FAN SPEED selector button to the setting you want If the fan speed is set to Automatic the fan speed switches automatically according to the difference between the actual room temperature and the temperature setting STEP 5 Press the FLAP button and set the airflow direction as desired Refer to Adjusting the Airflow Direction on page 20 To stop the air conditioner press the ON OFF operation button again O1 201 13EG 13 14 2 Adjusting the Fan Speed A Automatic Cooling mode B Manual 3 Fan Only Operation with the Remote Control Unit continued e Choose the best position in the room for the remote control unit which also acts as the sensor for room comfort and transmits the operating instructions Once you ve found this best position always keep the remote control unit there This appliance has a built in 3 minute time delay circuit to ensure reliable operation When the operation button is pressed the compressor will start running within three minutes In the event of power failure the unit will stop When the power is restored the unit will restart automatically after three minutes Simply set the FAN SPEED selector to the position A microcomputer in the air conditioner automat2. INSTRUCTION MANUAL Split System Air Conditioner COOL FAN Model Wall mounted type Ceiling mounted type Recessed type KS2432 152432 X 1822 XS1852 KS3032 1S3632 X 2432 KS3632 154232 XS3632 X54232 Save These Instructions Pub Ol 85464189201004 OSANYO 2003 Features These air conditioners are equipped with cooling function to these descriptions when using the air conditioner Microprocessor Controlled Operation The interior compartment of the remote control unit contains several features to facilitate automatic operation easy logically displayed for easy use Simple One touch Wireless Remote Control The remote control unit has several features to facilitate automatic operation 24 hour clock with ON OFF Program Timer The wireless remote controller allows you to set up a wide variety of time based operations Such functions include automatic on off with time settings same time on off every day on timer and off timer 1 Hour OFF Timer This timer can be set to automatically turn off the unit at any time after one hour e Night Setback Pressing this button changes the setting of the room temperature thermostat allowing you to set the temperature at whatever level that you find comfortable e Automatic and 3 step Fan Speed Auto High Medium Low Details on this function are provided below refer Air Sweep Control This function moves a flap up and down in the air outlet directing air in a swe
3. unit Do not wipe plastic parts using very hot water 2 Some metal edges and the fins are sharp and may cause injury if handled improperly be especially careful when you clean these parts 3 The internal coil and other components of the outdoor unit must be cleaned every year Consult your dealer or service center Air filter The air filter collects dust and other particles from the air and should be cleaned about once every six months Recessed type or two weeks ceiling mounted type and wall mounted type If the filter gets blocked the efficiency of the air conditioner drops greatly NOTE The frequency with which the filter should be cleaned depends on the environment in which the unit is used How to remove the filter Recessed type 1 Remove the bolt screw on each side out of the latch using a screwdriver After cleaning be sure to reattach the two bolt screws 2 Press on the two latches of the air intake grille with your thumbs in the direction of the arrow to open the grille 3 Open the air intake grille downward CAUTION When cleaning the air filter never remove the safety string If it is necessary to remove it for servicing and maintenance inside be sure to reinstall the safety string securely hook on the grille side after the work 4 Remove the air filter attached to the air intake grille Latch Safety string Air intake grille Bolt screw Air filter O1 201 21EG 21 Care and Clea
4. 201 08EG Remote Control Unit Sensor Transmitter H SANYO AIR CONDITIONER ROOM TEMP o ILI F ss LILG s zw NO LOVOHS SLAM 00h TA DIA rv oe gt Display Cover closed NIGHT SETBACK ON I OFF O NIGHT SETBACK button ON OFF operation button 1 HR TIMER button Temperature setting buttons MODE selector button FAN SPEED selector button FLAP button TIMER SELECT button TIMER AND PRESENT TIME setting buttons PROGRAM button ADDRESS switch ACL button Battery compartment Pull off the cover to expose the batteries o Y NOTE The illustration above pictures the remote control unit after the cover has been lowered and removed Transmitter When you press the buttons on the remote control unit the gt mark appears in the display to transmit the setting changes to the receiver in the air conditioner A temperature sensor inside the remote control unit senses the room temperature Display Information on the operating conditions is displayed while the remote control unit is switched on If the unit is turned off only the mode that was set previously is still displayed NIGHT SETBACK button For details see Night Setback Mode When you press this button in the COOL mode the mark appears in the display and the remote control unit automatically adjusts the set temperature to save energy Temperature setting Press the button to increas
5. control unit stops for more than ten minutes due to the loss of the remote control unit or other trouble the air conditioner will switch to the temperature sensor which ts built into the indoor unit and control the room temperature In these cases the temperature around the remote control unit may differ from the temperature detected at the air conditioner s position 10 Ol 201 10EG How to Install Batteries How to Use the Remote Control Unit Remote Control Unit Installation Position DO NOT Ol 201 11EG Using the Remote Control Unit 1 Slide the cover in the direction indicated by the arrow and remove it 2 Install two AAA alkaline batteries Make sure the batteries point in the direction marked in the battery compartment 3 Use a thin object such as the tip of a pen to press the ACL button ACL button The batteries last about six months depending on how much you use the remote control unit Replace the batteries when the remote control unit s display fails to indicate or when the remote control cannot be used to change the air conditioner s settings e Use two fresh leak proof type AAA alkaline batteries In replacing batteries follow the instructions as mentioned in the sub section How to Install Batteries If you do not use the remote control unit more than 1 month take out the batteries When using the remote control unit always point the unit s transmitter head directly at the air con
6. the same room which consume a lot of oxygen from the air Otherwise there is a risk of suffocation in an extreme case AN CAUTION Do not turn the air conditioner on and off from the power mains switch Use the ON OFF operation button Do not stick anything into the air outlet of the outdoor unit This is dangerous because the fan is rotating at high speed Do not let children play with the air conditioner Do not cool the room too much if babies or invalids are present O1 201 04EG Names of Parts Each air conditioner as shown below consists of an indoor unit and an outdoor unit You can control the air conditioner with the remote control unit Ceiling mounted type Recessed type Air outlet Air outlet Air intake Drain tube Renate Refrigerant control tubes Remote control Refrigerant unit unit tubes Wall mounted type Air intake Refrigerant oo tubes NOTE This illustration is based on the external view of a standard model Consequently the shape may differ from that of the air conditioner which you have selected The return air in the room is drawn into this section and passes through air filters which remove dust and foreign particles Conditioned air is returned to the room through the air outlet ceiling and wall mounted type or four air outlets Recessed type The direction of airflow can be adjusted as desired using the remote control unit Remote control unit The wireless r
7. ION Do not move the flap with your hands J pF TATA Y ww SITY ATA A aTa A A C D N ZN MODE FAN SPEED a E I a Air outlet p FLAP TIMER SELECT X Down grille Ke Operation without the Remote Control Unit If you have lost the remote control unit or it has trouble follow the steps below 1 When the air conditioner is stopped If you want to turn on the air conditioner switch the operation selector to the OFF position and then to the ON position NOTE The set temperature and fan speed are automatically set at the last selection before stopping 2 When the air conditioner is running If you want to turn off the air conditioner switch the operation selector to the OFF position Ol 201 20EG Care and Cleaning disconnect the power before cleaning 2 Do not pour water or spray detergent on the indoor unit to clean it This will damage the internal components and may cause an electric shock or fire AN WARNING 1 For safety be sure to turn the air conditioner off and also to Air Intake and outlet side Clean the air intake and outlet side of the indoor unit with a vacuum cleaner Indoor Unit brush or wipe them with a clean soft cloth If these parts are stained use a clean cloth moistened with a mild liquid detergent When cleaning the air outlet side be careful not to force the vanes out of place CAUTION 1 Never use solvents or harsh chemicals when cleaning the indoor
8. OUT SSO OUI G miii 23 Tips for Energy SAVING nascsisicsamessrnido sintio oie ttzateinntedeviecsletdpadeadens 23 Operating Rande sarita ada 23 Product Information If you have problems or questions concerning your Air Conditioner you will need the following information Model and serial numbers are on the nameplate on the bottom of the cabinet Model No Serial No Date of purchase Dealer s address Phone number Alert Symbols The following symbols used in this manual alert you to potentially dangerous conditions to users service personnel or the appliance WARNING This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death practice which can result in personal injury or product or property damage f CAUTION This symbol refers to a hazard or unsafe Installation Location We recommend that this air conditioner be installed properly by qualified installation technicians in accordance with the Installation Instructions provided with the unit e Before installation check that the voltage of the electric supply in your home or office is the same as the voltage shown on the nameplate Do not install this air conditioner where there are fumes or flammable gases or in an extremely humid space such as a greenhouse Do not install the air conditioner where excessively high heat generating objects are placed Avoid To protect the air conditioner from heavy corrosion
9. avoid installing the outdoor unit where salty sea water can splash directly onto it or in sulphurous air near a spa The unit may malfunction when the receiver in the indoor unit is exposed to the Inverter lamp light Electrical Requirements 1 All wiring must conform to the local electrical codes Consult your dealer or a qualified electrician for details 2 Each unit must be properly grounded with a ground or earth wire or through the supply wiring 3 Wiring must be done by a qualified electrician e Power supply 60 Hz single phase 230 208 volts yo To warm up the system the power mains Power mains must be turned on at least five 5 hours before operation Leave the power mains ON unless you will not be using this appliance for an extended period CL MODEL Safety Instructions Read this Instruction Manual carefully before using this air conditioner If you still have any difficulties or problems consult your dealer for help e This air conditioner is designed to give you comfortable room conditions Use this only for its intended purpose as described in this Instruction Manual AN WARNING e Never touch the unit with wet hands Never use or store gasoline or other flammable vapor or liquid near the air conditioner it is very dangerous This air conditioner has no ventilator for intaking fresh air from outdoors You must open doors or windows frequently when you use gas or oil heating appliances in
10. ct the power Use the main power switch to turn off power completely TEST position This position is used only when servicing the air conditioner f CAUTION Do not set at the TEST position for normal operation OPERATION lamp This lights when the system is in the continuous COOL or FAN mode TIMER lamp This lamp lights when the system is being controlled by the timer lamp This lamp lights when the system is being controlled by the timer when the system is being controlled by the timer Ol 201 07EG 7 Remote Control Unit Display ROOM TEMP is displayed when the temperature setting has not been made Displayed when main unit sensor is in use o a paai TEMP is displayed when setting temperature Displayed when transmitting data Displayed when temperature is shown Displayed when the temperature setting is at the upper or lower allowable limit Displayed when setting timer Symbols 1 Operation mode 3 Set temperature 60 86 F When set to 82 F COOL vwsesnsnsnnnnnnnnnnnee Current temperature indication A A PP 24 hour clock with ON OFF P TIMET csscseseeseseeseseeeen ON y rogram Timer o 24 hour ON TIME ON C 24 hour OFF Timer eceseeeee OFFC 1 hour OFF Timer LOW cocccccccssssececceccesssseseececeesssee MES 5 NIGHT SETBACK coccion 6 Confirmation of TTANSMISSION cccccnnnncnnnnanannanas S 7 Sweep indication 00 8 O1l
11. ditioner s receiver Air conditioner Indoor unit ESA N Receiver gt lt Transmitter head Remote control unit The remote control unit may be operated either from a non fixed position or from a wall mounted position To ensure that the air conditioner operates correctly DO NOT install the remote control unit in the following places e In direct sunlight e Behind a curtain or other places where it is covered e More than 26 feet 8 m away from the air conditioner e Inthe path of the air conditioner s airstream e Where it may become extremely hot or cold e Where it may be subject to electrical or magnetic noise e Where there is an obstacle between the remote control unit and air conditioner since a check signal is sent from the remote control unit every 5 minutes 11 12 Mounting the Remote Control Unit When attaching to wall When using the remote control unit Securing the remote control unit to prevent theft Using the Remote Control Unit continued Truss head tapping screws 5 32 x 5 8 4 x 16 mm supplied Remote control unit holder 1 Confirm the indoor unit beeps when the ON OFF button is pressed at the wall location where the remote control unit is to be attached then attach the holder to the wall 2 When taking out the remote control unit pull it from the holder e Point the transmitter on the remote control unit at the sensor on the indoor unit wh
12. e the set temperature buttons TEMP Press the button to reduce the set temperature ON OFF operation button This button is for turning the air conditioner on and off Timer and Present Time First press the program button to select the mode you want setting buttons Each time you press the HH button the hours advance by one Each time you press the MM button the minutes advance by one Ol 201 09EG 9 Remote Control Unit continued Program button For details see Setting the Timer Press this button to select the mode you want to program TIMER SELECT button No display The timer does not operate The air conditioner stops at the set time The air conditioner starts at the set time OY The air conditioner stops and starts or starts and stops at the set times every day MODE selector button Use this button to select the COOL or FAN mode COOL The air conditioner makes the room cooler FAN The air conditioner works only as a circulation fan FLAP button Press this button to select the sweep function which moves the flap up and down automatically aN The flap moves up and down automatically FAN SPEED selector button The air conditioner automatically decides the fan speeds e High fan speed se Medium fan speed se Low fan speed 1 HR TIMER button When you press this button regardless of whether the unit is 1 HOUR OFF TIMER operating or stopping the u
13. emote control unit controls power ON OFF operation mode selection temperature fan speed timer setting and air sweeping Refrigerant tubes The indoor and outdoor units are connected by copper tubes through which refrigerant gas flows Moisture in the room is condensed and drains off by means of this tube Outdoor condensing unit The outdoor unit contains the compressor fan motor heat exchanger coil and other electrical components O1 201 05EG 5 Unit Display and Operation Selector Recessed type Ceiling mounted type OPERATION TIMER Remote control lamp lamp receiver Recessed type Ceiling mounted type Operation selector TEST OFF ON Le Air intake IL grille NO 330 1831 Air filter Operation selector Ol 201 06EG Unit Display and Operation Selector continued INDOOR UNIT E _ _ _ _ EEK e el lt _ lt A gt M gt MMM24 CHEO y REMOTE CONTROL receiver OPERATION lamp Operation selector TIMER lamp REMOTE CONTROL This section picks up infrared signals from the remote control unit receiver transmitter Operation selector ON position This position is for operating the air conditioner with the wireless remote control unit Set the selector normally in this position OFF position Switch the selector to the OFF position if you are not going to use the air conditioner for a few days or longer WARNING The OFF position does not disconne
14. en operating the remote control unit and the air conditioner e Do not place objects which may block the transmitted signals between the receiver and the remote control unit Truss head tapping screws 5 32 x 5 8 4 x 16 mm supplied Holder Remote control unit holder 1 Attach the holder to the wall with one screw in the upper hole only NO Remove the cover from the remote control unit and then remove the batteries Next place the remote control unit in the holder Secure both the remote control unit and the holder to the wall with another screw through the lower hole 3 4 Put the batteries back in the remote control unit and then replace the cover Ol 201 12EG Operation with the Remote Control Unit 1 Operation SANYO AIR CONDITIONER ROOMTEMP oN AM erar AS MERA NIGHT seTBACK ON 0FF O STEP 4 NOTE Check that the circuit breaker on the power panel is turned on and that the operation selector of the indoor unit is in the ON position Press the setting buttons as described below and change the settings as desired STEP 1 Set the MODE selector button to COOL For cooling operation gt Ses STEP 2 To start the air conditioner press the ON OFF operation button STEP 3 Press the TEMP setting buttons to change the temperature setting to the desired temperature Adjustable temperature range 86 F max
15. eping motion around the room and providing comfort in every corner Automatic Restart Function for Power Failure Even when power failure occurs preset programmed operation can be reactivated once power resumes Anti Mold Filter This unit is equipped with an anti mold filter that inhibits the growth of mold and bacteria Ol 201 02EG OI 201 03EG Contents Page Feat AP e A A rollo A 2 Product ION ON a E N 3 a O 3 SCANLON LOCO Nai EOS 4 Electrical Requirements rara ata 4 Salte y IASTUCIONS e 4 Names Of Rams orto 5 Using the Remote Control Unit ccccoccccnncnccncinonncnnnncncnnancnnncnonanonnnnncnnnnnonanonnnnns 11 Operation with the Remote Control UnNit occcccocncnnccncccnnonanncnanoconancnnaroconnnonos 13 ODE IO se visa 13 2 Adjusting the Fan Speed ccccsseccssecesecsseeeeseceseeceseeeseeeeaeesseeeeaeenseees 14 A A A R A 14 4 Night Setback Mode ccccccescccsssceseseeceeeeceeeeeeeeeeeseeessaeeeseeesseeessaeeens 15 Special Remarks ccccesccscccseccceeeceeeceeceeeeceeceseecaeeeegeesseeeegeesgeseegeeegessegeeeaeesagees 16 Setmana TIME so aepsrcrb ronca E 17 Using the 1 Hour OFF Timetr cccccssccccsesceccsseeceseeecsceeeceaeesseageessaeeeesseeeesssas 19 Adjusting the Airflow Direction ccccccccsecccseseeseeeseecessaseesaeeessueesseeeesseeessaees 20 Operation without the Remote Control Unit cooccccocnccccnccnanoconnnconanonnanoconnnnnos 20 Care A A Re oe E EE E cans 21 T
16. fter 10 sec displayed 2 How to set the OFF time Example To stop the air conditioner at 11 30 pm OFF Press the Program button e ON The timer indication blinks once and present OFF time is shown e Press the HH button until PM 11 is The display will change displayed automatically back to show the e Press the MM button until 30 is present time after 10 sec displayed Press the ON OFF button to start the The present time is displayed air conditioner Press the TIMER SELECT button to The present time and are set OFF time displayed Ol 201 17EG 17 Setting the Timer continued 3 How to set the ON time Example To start operation at 7 10 am operation Cito OFF Press the Program button ON The timer indication blinks and present ON time is shown e Press the HH button until AM 7 is The display will change displayed automatically back to show the Press the MM button until 10 is Present time after 10 sec displayed Press the ON OFF button to start the The present time is displayed air conditioner Press the TIMER SELECT button to The present time and are set ON time displayed 4 How to set a program Example To start operation at 7 10 am and stop the air conditioner at for daily ON OFF 11 30 pm operation 7 10 am 11 30 pm ON OFF Present time OFF Set the timer ON OFF times as time shown in 2 1 2 and 3 1 2 Press the ON OFF button to s
17. ically controls the fan speed when the mode is selected When the air conditioner starts operating the difference between the room temperature and the set temperature is detected by the microcomputer which then automatically switches the fan speed to the most suitable level When difference between room temperature and set temperature is Between 4 F and 2 F The above table assumes that the sensor on the remote control is being used If the sensor on the indoor unit is being used the indicator is on actual operation may differ slightly from the operation described in the table Refer to SENSOR button on page 10 If you want to adjust fan speed manually during operation just set the FAN SPEED selector as desired 93 8 or NIGHT seTBACK ON I OFF O STEP 1 STEP 3 FLAP TIMER SELECT DD Cc If you want to circulate air without any temperature control follow these steps STEP 1 Press the MODE selector button to switch to the fan mode 8 STEP 2 Press the ON OFF button STEP 3 Press the FAN SPEED button to select the fan speed of your choice 383 IN or 5 Ol 201 14EG Operation with the Remote Control Unit continued 4 Night Setback Mode ROOM TEMP BlO EI JN reer S IPM ILI LILI NIGHT serBack ON I 0FF O m N l o MODE FAN SPEED A ME FLAP TIMER SELECT Night Setback Mode is used for saving energy Press the NIGHT SETBACK butto
18. ir intake and outlet of the unit If either is obstructed the unit will not work well and may be damaged Let direct sunlight into the room Use sunshades blinds or curtains If the walls and ceiling of the room are warmed by the sun it will take longer to cool the room Do e Always try to keep the air filter clean Refer to Care and Cleaning A clogged filter will impair the performance of the unit To prevent conditioned air from escaping keep windows doors and any other openings closed NOTE Should the power fail while the unit is running If the power supply for this unit is temporarily interrupted the unit will automatically resume operation once the power is restored with the same settings that were in effect before the power was interrupted Operating Range The air conditioner is operable within the temperature ranges as listed below PA Temperature Indoor air temperature Outdoor air temperature 95 F DB 71 F WE 115 F DB si in 67 F DB 57 F WB 67 F DB 0 F DB Only for CL Models Ol 201 23EG 23 In Canada SANYO FISHER COMPANY SANYO Canada Inc A DIVISION OF SANYO NORTH AMERICA CORPORATION 300 Applewood Crescent 21605 Plummer Street Concord Ontario Chatsworth CA 91311 U S A L4K 5C7 Canada
19. le the 1 Hour Timer function is operating the 1 HR TIMER button is pressed once to cancel the function and then again the unit continues to operate for one hour from that point in time and then stops The 1 Hour OFFTimer setting is given priority over the daily program setting It is not possible to use the OFFTimer and 1 Hour OFF Timer together Whichever function is set last takes precedence If the 1 HR TIMER button is pressed while the TIMER OFF function operates OFF Timer is cancelled and the unit will stop operating one hour later 19 Indoor unit Wall mounted type for COOLING INDOOR UNIT Operation Flap selector Wall mounted type 20 Adjusting the Airflow Direction A Horizontal Wall mounted type only The horizontal airflow can be adjusted by moving the vertical vane to the left or right J AS Ryd Left da y y Vertical vane B Vertical Confirm that the remote control unit has been turned on Press the FLAP button to start the flap moving up and down 2 If you want to stop the flap movement and to direct the air in the desired direction press the FLAP button again In the COOL mode don t direct the flap down more than 30 KS TS Types or leave it in the vertical position XS Type otherwise condensation may drip onto the floor Zone A KS TS Type and any position other than vertical XS Type are the recommended flap positions for cooling CAUT
20. n while operation The mark appears in the display To release the night setback function press the NIGHT SETBACK button again NOTE The night setback mode cannot be used during automatic operation In Cooling Mode When the night setback mode is selected the air conditioner automatically raises the temperature setting 2 F when 30 minutes have passed after the selection was made and then another 2 F after another 30 minutes have passed regardless of the indoor temperature when night setback was selected This enables you to save energy without sacrificing comfort This function is convenient when gentle cooling is needed Setting temperature 2 F L Press the 30 min NIGHT SETBACK button Ol 201 15EG 15 Power failure during operation Remote Control Unit 16 Special Remarks In the event of power failure the unit will stop When the power is resumed the unit will restart automatically after three minutes The remote control unit sends the setting condition to the air conditioner regularly at three minute intervals Ol 201 16EG setting the Timer 1 How to set the Example To set to 9 10 pm present time operation O titan OFF 1 Press the Program button e ON The time indication alone blinks three times e Press the HH button until PM 9 is The display will saya ae displayed stop blinking except for the Press the MM button until 10 is symbol a
21. ning continued How to remove the filter Ceiling mounted type 1 Remove the bolt screws on the latch using a screwdriver After cleaning be sure to reattach the two bolt screws 2 Take hold of two latches on the air intake grille and press it to the rear and the grille will open downward 3 Take hold of the finger hold on the air filter first lift it and then pull it toward you to release it from the catch Air filter Air intake grille Air filter finger hold How to remove the filter Wall type 1 Move the flap on the air outlet grille to its lowest position 2 Hold the air filter by the tab at the bottom and pull downward How to clean the filter Use a vacuum cleaner to remove light dust If there is sticky dust on the filter wash the filter in lukewarm soapy water rinse it in clean water and dry it Outdoor Unit 1 Certain metal edges and the condenser fins are sharp and may CAUTION cause injury if handled improperly special care should be taken when you clean these parts AN 2 Periodically check the outdoor unit to see if the air outlet or air intake is clogged with dirt or soot 3 The internal coil and other components of the outdoor unit must also be cleaned periodically Consult your dealer or service center Care After a Prolonged Idle Check the indoor and outdoor unit air intakes and outlets for blockage if Period there is a blockage remove it Care Before a Prolonged Idle Operate the fan fo
22. nit operates for one hour and then shuts down ACL button ALL CLEAR Puts the remote control unit into pre operation status Always press this button after replacing the batteries ADDRESS switch Change the address switch to prevent mixing of signals from remote control units when two Sanyo air conditioners are installed next to each other Normally the remote control address switch is set to A For the second indoor unit both addresses of the remote control unit and the indoor unit must be changed The second remote control unit address must be changed to B by breaking off the tab A And the second indoor unit address must be changed from 1 OFF 2 OFF to 1 ON 2 ON by switching the dip switch in the indoor unit For more information please contact the dealer where you made the purchase e Normally the tabs on the remote control unit should not be bent SENSOR button When you press this button use a small tipped object such as a ballpoint pen the mark will appear at the display And the room temperature is detected by the sensor which is built into the indoor unit and the air conditioner is controlled accordingly If the remote control is located near a heat source such as a space heater or in direct sunlight press the SENSOR button to switch to the sensor on the indoor unit The remote control unit sends the temperature signal to the air conditioner regularly at five minute intervals If the signal from the remote
23. r half a day to dry out the inside Period Disconnect the power supply and also turn off the breaker Clean the air filter and replace it in its original position e Outdoor unit internal components must be checked and cleaned periodically Contact your local dealer for this service 22 O1 201 22EG Troubleshooting If your air conditioner does not work properly first check the following points before requesting service If it still does not work properly contact your dealer or service center Possible Cause Air conditioner does not 1 Power failure 1 Restore power run at all 2 Leakage breaker tripped 2 Contact service center 3 Line voltage is too low 3 Consult with electrician or dealer 4 ON OFF operation button is OFF 4 Press the button again 5 Batteries in remote control unit have 5 Replace batteries run down Compressor runs but 1 Obstruction in front of condenser 1 Remove obstruction soon stops coll Poor cooling 1 Dirty or clogged air filter 1 Clean the air filter to improve the air performance flow 2 Heat source cooker heater or 2 Eliminate heat source if possible electrical appliance or many people in room 3 Doors and or windows are open 3 Shut them to keep the heat out 4 Obstacle near air intake or air 4 Remove it to ensure good air flow discharge port 5 Thermostat is set too high 5 Set the temperature lower Tips for Energy Saving Do not Block the a
24. tart the alr conditioner Press the TIMER SELECT button to The present time PM 9 10 and ON set the ON OFF combination timer lt are displayed time When the Daily ON OFF program is set to start the air conditioner before the ON time setting the 0 indications appear on the display On the other hand when the Daily ON OFF program is set to start the a air conditioner after the ON time setting the Oy indications ON OFF appear on the display Thus these indications show the timer program which will operate next NOTE You can check the timer ON OFF times after you have set them by pressing the PROGRAM button 18 Ol 201 18EG 1 1 Hour OFF Timer 1HR O NIGHT SETBACK ON OFF O o o Ee MODE FAN SPEED 2 Operation Together with the Program Timer Ol 201 19EG Using the 1 Hour OFF Timer This function causes the unit to operate for one hour and then stop regardless of whether the unit is on or off when this button is pressed The indicator in the display indicates that this function is operating Setting procedure Regardless of whether the unit is operating or stopped press the 1 HR TIMER button appears in the display Cancellation procedure Press the ON OFF operation button to turn the unit off wait for the unit to stop operating and then press the ON OFF operation button again The 1 HourTimer function is now cancelled and the unit operates normally If whi
Download Pdf Manuals
Related Search