Sanus Systems VMAA26 User's Manual
Contents
1. M5 Diameter Bolt M8 Diameter Bolt Step 2 Mounting the Monitor Brackets to Televisions with a curved back or other obstruction Determine the diameter of the Bolt T U V W your TV requires by hand threading them into the threaded insert on the back of the TV If you encounter any resistance stop immediately Once you have determined the correct diameter refer to the appropriate Diagram below Thread the Bolt through the appropriate Lock Washer X Y Z AA a Washer DD EE the Monitor Bracket E a second Washer DD M4 M5 diameter only a Spacer BB CC and finally into the TV Make sure the Monitor Brackets are vertically centered and level with each other Repeat the process until each Monitor Bracket is secured to the TV with two bolts MNN ty hit i AN Diagram 2 Step 3 Add the Vise Assemblies to the Monitor Brackets NOTE Do not overtighten the 1 4 20 Nut M The Vise Assembly F should be able to rotate freely around the Carriage Bolt L Place the Vise Assembly F into the Monitor Bracket E so that the two Jaws point toward the set of 1 diameter holes and the Allen Bolt is facing away from the television Place a 2 Carriage Bolt L through the square hole in the side of the Monitor Bracket and the Vise Assembly then through the square hole in the other side of the Monitor Bracket Thread and tighten a 1 4 20 Nut M onto the end of the 2 Carri2. 8 Add Preventor A CAUTION Avoid Pinch Points Placing your hands or fingers between moveable parts Pinch Points may result in personal injury Determine which direction you want the Arm to fold If you want the Arm to fold to the right place the Preventor C on the right side of the Arm Assembly B If you want the Arm to fold to the left place the Preventor on the left side of the Arm Assembly Position the Preventor so the flat side is facing the Idler as shown in the Detailed View of Diagram 8 To attach the Preventor place a Preventor Bolt O through the Preventor and into the holes in the Idler Tighten the Preventor Bolts with an Allen Key K Diagram 8 Detail View g c ena 9 O e 9 Ai o st i Idler 9 8 Step 9 Cable Management ACAUTION Do not run Cables through a Pinch Point Running Cables through Pinch Points may result in damage to the Cables Before beginning cable management pull the television into the position as far from the wall as possible Leave some slack in the cables so that during motion so there is no added tension on the connectors There are several places to attach Wire management ties to keep cables out of the way Wire Tie Clips G can be attached to the holes
3. Bolt P Qty 4 M4 x 30 mm Bolt T Qty 4 se M4 Lock Washer X Qty 4 M4 M5 Spacer BB Qty 4 HA WY M5 x 12 mm Bolt Q Qty 4 M5 x 30 mm Bolt U Qty 4 6 M5 Lock Washer Y Qty 4 M M8 Spacer CC Qty 4 NAA HAWN Qty 4 7 32 amp 3 16 Allen Keys K Qty 1 Each AAA aT Preventor Bolt O Qty 2 Qty 4 M6 x 35 mm Bolt V Qty 4 6 M6 Lock Washer Z Qty 4 M4 M5 Washer DD Qty 8 M8 Lock Washer AA Qty 4 M6 M8 Washer EE Qty 4 Step 1 Mounting Monitor Brackets to a Televisions with a flat back NOTE For TVs with a curved back or any other obstruction See Step 2 After completing this step proceed to Step 3 Determine the diameter of the Bolt P Q R S your TV requires by hand threading them into the threaded insert on the back of the TV If you encounter any resistance stop immediately Once you have determined the correct diameter refer to the appropriate Diagram below Thread the Bolt through the appropriate Lock Washer X Y Z AA a Washer DD EE the Monitor Bracket E and finally into the TV Make sure the Monitor Brackets are vertically centered and level with each other Repeat this process until each Monitor Bracket is secured to the TV with two bolts M4 Diameter Bolt M6 Diameter Bolt Diagram 1
4. both the Arm Assembly and the second Monitor Bracket are aligned so that the 1 Diameter Tubes will pass between the jaws NOTE Do not over tighten the Vise Assembly F or the Vise Assemblies in the Arm Assembly B When tightening the Vise Assemblies turn the Allen Bolt in until resistance is felt then tighten the Allen Bolt approximately 1 amp 1 2 turns or until the head of the Allen Bolt is slightly above the surface of the Vise Assembly The 1 Diameter Tubes D must not be able to move from side to side when the Vise Assembly is properly tightened Once the 1 Diameter Tubes are in place tighten the allen bolts on the 4 Vise Assemblies in the two Monitor Brackets with the 3 16 Allen Key K to lock the television to the mount Slide the Arm Assembly into the desired position between the two Monitor Brackets Sanus recommends Arm Assembly be centered between the Monitor Brackets and tighten the two remaining Allen Bolts in the Vise Assemblies inside the Arm Assembly Detail View F Diagram 4b Step 5 Attach the Wall Plate Wood Stud installation only A CAUTION Do not overtighten the Lag Bolts Tighten Lag Bolts I only until the Lag Bolt Washer J is pulled firmly against the Wall Plate A If there is a layer of drywall or other material this drywall or other material may not exceed 5 8 inch 15 8 mm in thickness Failure to heed this caution may result in property damage and or pe
5. in the top and the bottom of the Arm Assembly B sides of the Preventor C and the top and bottom of the pillow block by simply pressing them into place as shown in the Detailed View of Diagram 9 Wire Ties H can then be added to both the Wire Tie Clips or the holes in the sides of either of the Monitor Brackets E Diagram 9 Detail view a gt i il i f Ta Jle A o 2 l al CSAYV Inc and its affiliated corporations and subsidiaries collectively CSAV intend to make this manual accurate and complete However CSAV makes no claim that the information contained herein covers all details conditions or variations Nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind CSAV makes no representation of warranty expressed or implied regarding the information contained herein CSAV assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document
6. SANUS SYSTEMS THE UNION OF FORM AND FUNCTION Assembly Instructions for Model VMAA26 Thank you for choosing a Sanus Systems VisionMount wall mount The VMAA26 is designed to mount up to 50 Flat panel televisions weighing up to 130 Ib to a vertical wall It allows you to tilt the television from 5 to 15 It will also extend 25 75 away from the wall swivel up to 180 and roll 6 CAUTION The size and weight of your television must not exceed 50 1270 mm diagonally and 130 Lbs 59 Kg The wall must be capable of supporting five times the weight of the television plus the wall mount Never use defective parts Improper installation may cause property damage or personal injury Do not use this product for any purpose that is not explicitly specified by Sanus Systems If you do not understand these directions or have any doubts about the safety of the installation please call a qualified contractor or contact Sanus at 800 359 5520 or www sanus com Our customer service representatives can quickly assist you with installation questions and missing or damaged parts Replacement parts for products purchased through authorized dealers will be shipped directly to you Check carefully to make sure that there are no missing or defective parts Sanus Systems can not be liable for damage or injury caused by incorrect mounting incorrect assembly or incorrect use Please call Sanus Systems before returning products to the point of purc
7. age bolt Repeat this step for the bottom of the Monitor Bracket then repeat this process for the second Monitor Bracket See Diagram 3 and Vise Detail Vise Detail Diagram 3 Step 4 Attach the Arm Assembly to the Television Align each Vise Assembly F so that a 1 Diameter Tube D will pass through the 1 round hole in the Monitor Bracket E and between the jaws of the Vise Assembly Insert a 1 Diameter Tube through the top hole in the first Monitor Bracket Repeat this step for the Bottom hole in the same Monitor Bracket See Diagram 4a for assistance Diagram 4a q Step 4 Attach the Arm Assembly to the Television Continued on next page Step 4 Attach the Arm Assembly to the Television Continued A CAUTION The 1 Diameter Tubes D must extend beyond the outside edges of both Monitor Brackets E and the Allen Bolts in all 6 Vise Assemblies F must be tightened Failure to do this will result in an installation that unstable and may result in property damage and or personal injury Position the Arm Assembly B so the hook shaped tab shown in Detail View of Diagram 4b is on the top Line up the two 1 diameter holes in the Monitor Bracket E at the other end of the Arm Assembly with the with the 1 Diameter Tubes D Push the 1 Diameter Tubes through the bracket on the Arm Assembly then through the other Monitor Bracket Make sure the Vise Assemblies F on
8. hase NOTE This mount is not intended for use on brick concrete block concrete or steel wall studs Typical wall anchors do not have sufficient holding power to support this mount It is up to the installer to verify the safety of any installation method or hardware that is not provided by or recommended by Sanus Systems Sanus Systems makes every effort to assure all necessary television mounting hardware is included If the television mounting hardware you need is not included please consult your local hardware store or call Sanus Systems Required Tools 3 16 drill bit drill adjustable or crescent wrench Phillips screwdriver Supplied Parts Some parts are not shown at same scale P Wall Plate A reventor C Arm Assembly B Qty 1 Qty 1 ty 4 y I Diameter Tube D Monitor Bracket E Vise Assembly F Qty 2 Qty 2 Qty 4 Sanus Systems 2221 Hwy 36 West Saint Paul MN 55113 09 26 06 6901 100017 Customer Service 800 359 5520 See complementary Sanus products at www sanus com Hardware Hardware shown is actual size Wire Tie Clip G Qty 7 Lag Bolt I Qty 4 2 Carriage Bolt L Qty 4 Qty Wire Tie H 10 Lag Bolt Washer J SZ Q 1 4 20 Nut M Qty 4 Qty 4 onni LT Safety Bolt N Qty 3 Supplied Television Mounting Hardware Hardware shown is actual size mm M4 x 12 mm
9. ight A loose Safety Bolt will result in an unstable installation which may result in property damage and or personal injury Thread each Safety Bolt N into one of the three holes in the bottom of the Transfer Plate and tighten them so that they are behind the Tab on the bottom of the Wall Plate as shown in Diagram 6b Transfer Plate Step 7 Leveling the Monitor and Adjusting the Tension ACAUTION Do not remove the Tension Nuts in Diagram 7 Removing Tension Nuts will result in property damage Once the television is mounted onto the Wall Plate A and the Safety Bolts N are tight it can be adjusted to level Slightly loosen the two Allen Bolts on the back of the Arm Assembly B Once the Allen Bolts are loosened the television can be adjusted 6 until level When the television is level retighten the two Allen Bolts The tilt can be adjusted by setting the tension of the Tension Knobs and tilting the television The Tension Nuts labeled in Diagram 7 can be slightly loosened or tightened using the 7 32 Allen Key K and wrench to adjust the tension of the Arm Assembly If you need to adjust the Tension Nut closest to the TV you must remove the Safety Bracket adjust the tension and re install the Safety Bracket as shown in Safety Bracket Installation Safety Bracket Installation Diagram 7 Step
10. rsonal injury The Wall Plate A must be mounted to two wood studs at least 12 apart Use a high quality stud sensor to locate two adjacent studs Verify where the studs are located with an a awl or thin nail Pre drill a 2 5 deep hole in each stud at i the desired height using a 3 16 drill bit Make sure these P l Diagram 5 holes are in the center area of the studs and level with each other Use the Wall Plate as a template to mark the location of the second hole in each stud Drill 2 5 deep holes using the 3 16 drill bit in the marked location Attach the Wall Plate to the wall using four Lag Bolts I and four Lag Bolt Washers J Make sure the Wall Plate is oriented so the flat surface in the center of the plate is against the wall See Diagram 5 for assistance Drywall cut away e T to show studs Step 6 Hang the assembly onto the Wall Plate A CAUTION This step may require two people to lift the assembly onto the Wall Plate Sanus is not responsible for property damage and or personal injury Orient the Arm Assembly B so the arm extends directly away from the television and the Transfer Plate is parallel with the television Lift the assembly and hook the Transfer Plate onto the tab on the top of the Wall Plate A as shown in Diagram 6a Horizontally adjust the Transfer Plate side to side on the Wall Plate until it is in the desired location ACAUTION make sure the Saftey Bolt N is t
Download Pdf Manuals
Related Search