Sanus Systems PFPL User's Manual
Contents
1. Important When fitting the rails onto the top ensure that the grooved part of the rails are closest to the side edges of the top The larger holes cam holes in the rails must always be closest to the Top 1 Insert black Barrel Nuts into smaller holes in Rails ensuring slot in cap is aligned to intersecting hole 2 Insert silver Cams into larger holes in Rails ensuring that arrow on Cam points towards intersecting hole 3 Press fit Rails to Top as shown eseq Jey u SAL Bunueuiejduioo ufisep zuo yey UM puejs snues eseq peAuno YM SA Bunueuiejduuoo uBisep uos peAuno uy puejs snueg juody eld uoJ4 paving MSN gt juoJJ pening NOIS3d Jj I8ISH3A3M uondo puejs JUOL e4 OY 104 Ie Gy pue go9 gc gr sdejs seeJeuw uondo pueys 1u0JJ PSAINO y 10 9Je v pue vo vs vp sdejs joA9woH suDisep ujoq 104 euies y eje suononujsur A quiesse y ui sdejs SOW pesua Buey eseq 9 do 3u0JJ zey Jo eseq do JUO peAuno 13441 uj pejquuesse eq UBD pueys eu seseq jej pue peAuno u SA 1ueuiejduioo o peufiisep ueeq seu puejs snueg eu SUL INVLYOdNI ASSEMBLING THE STAND WITH CURVED FRONT STEP 4A Back edge Flat p Front edge 1 Insert black Barrel Nuts into holes in Sides ensuring slot in cap is aligned to intersecting hole 22. STEP 7B Locking screw x8 di ARN vm Front edge Flat m annu N va TD KANSAS d 1m g Back edge curved o 1 With assistance align Base onto Dowels in Sides amp Rails amp then press fit 2 Fasten large Locking screws through Base into Sides amp Rails Screw heads should be flush with surface Following steps apply to both flat and curved front designs STEP 8 Screw x6 1 Fasten the glides to the base as shown Adjusting screw x 4 1 Turn unit over carefully 2 Screw each Adjusting screw into Side by half of it s visible threaded length then once this is done tighten all 4 Adjusting screws fully into Side STEP 10 Curved edge of the glass Flat edge of the glass shelves must be placed at front shelves must be placed at for curved front design front for the flat front design Glass shelf Shelf Pin x8 i Front edge curved Front edge flat 1 Insert Shelf Pins into holes at the lower positions of both the Sides as illustrated above 2 Tilt and slide Glass Shelf between Rails ensuring frosted side down and place on top of Shelf Pins 3 Insert Shelf Pins into holes at the upper positions of one Side only 4 Tilt and slide the second Glass Shelf between Side Rails While holding one end of the shelf on pins o
3. A0 PART DESCRIPTION oO lt Top Base Side A Side B Rail Rail Thin panel Glass Shelf Angle Brace Glide Hardware Pack 1 1 1 1 2 2 2 2 1 6 1 TOOLS REQUIRED PHILLIPS No 2 SCREWDRIVER CUSTOMER SERVICE INFORMATION IN THE UNLIKELY EVENT OF PARTS BEING FAULTY OR MISSING CHECK PACKAGING REPLACEMENT PARTS CAN BE OBTAINED BY CALLING THE TOLL FREE NUMBER WITHIN 14 DAYS OF PURCHASE TOLL FREE NUMBER 1800 359 5520 USA ONLY THE FOLLOWING INFORMATION MUST BE SUPPLIED IN FULL 1 YOUR NAME ADDRESS AND TELEPHONE NUMBER 4 PURCHASE DETAILS STORE THE UNIT WAS PURCHASED FROM 2 PRODUCT MODEL NAME NUMBER AND COLOR DATE OF PURCHASE 3 DESCRIPTION PART NUMBER AND QUANTITY 5 SERIAL NUMBER OF THE UNIT PURCHASED OF REQUIRED PARTS LOCATED ON REAR OF UNIT Hardware Contents CAUTION There are many small components used in the construction of this unit These loose items should be kept away from young children while assembling your unit Shelf Pin Barrel nut P840048 x 8 P860121 x 1 P860035 x 6 P840050 x 8 Connector rod Wooden dowel P860015 x 8 P820016T x 8 P820015T x 8 P800201 x 8 QR P816145 x4 Cable Ducts P840170 x 2 Wooden Dowels x 8 Insert wooden dowels into sides as shown 1 Fasten 8 Connector Rods into small holes in Top as shown Intersecting hole Grooved ef lp
4. BUS5305 PLATINUM FURNITURE MODEL PFPL Digital TV Stand Assembly Instructions Congratulations and thank you for purchasing your new Sanus Platinum Furniture Product If you have any questions regarding this or any other Sanus product please contact our customer service department at 800 359 5520 or www sanus com It is not necessary to contact the retailer with any questions or problems as parts can be sent directly to you Please follow these assembly instructions This will save you time make assembly easier and prevent possible damage to your new Digital TV Stand Assistance may be required for some assembly procedures Correct assembly is your responsibility BUS5305 We recommend that the unit is assembled on a soft surface such as carpet Please record your serial number in the space provided below and retain this manual for future reference Serial No This unit was manufactured using ISO 9000 certified systems For improvement purposes design and specifications are subject to change without notice SA NU SIS Y 55 TEMS THE UNION OF FORM AND FUNCTION UNPACK AND IDENTIFY PARTS Small hole f Angle Brace Large hole t Thin pane D Rail Side A Side B 7j3 Rail Thin Panel Glass Shelf PART NUMBER Stipple silver M19965A1SS M19966A1SS M19967A1SS M19968A1SS M19969A1SS M19970A1SS M19971A1SS M19972A1PO M19111A1PO P815049 MH1139
5. Insert silver Cams into large holes in sides ensuring that arrow on Cam points towards Top panel 3 Press fit Side s to Top ensuring Angle Brace is in slots in Sides ensuring orientation of Metal Brace as shown STEP 5A 1 eal 1 Secure Angle Brace to Top as shown above STEP6A 1 Slide Thin Panels down slots in Rails ensuring Silver surfaces face out STEP 7A Back edge Flat Frontedge 7 curved 1 With assistance align Base onto Dowels in Sides amp Rails amp then press fit 2 Fasten large Locking screws through Base into Sides amp Rails Screw heads should be flush with surface ASSEMBLING THE STAND WITH FLAT FRONT STEP 4B O Black Barrel nut x 4 Front edge Flat Back edge curved 1 Insert black Barrel Nuts into holes in Sides ensuring slot in cap is aligned to intersecting hole 2 Insert silver Cams into large holes in sides ensuring that arrow on Cam points towards Top panel 3 Press fit Side s to Top ensuring Angle Brace is in slots in Sides ensuring orientation of Metal Brace as shown STEP 5B 1 1 Secure Angle brace to Top as shown above STEP6B 1 Slide Thin Panels down slots in Rails ensuring Silver surfaces face out
6. n one side insert remaining Shelf Pins into other side beneath Glass then lower the shelf on top of the pins STEP 11 ce FAZ a Cable Duct x2 Back edge 1 Press fit 2 Cable Ducts into large holes in the Base 2 You have now completed the assembly of your new Digital TV stand NOTE We recommend that all contents stored in or on this item of furniture be removed before shifting it The manufacturers will not be held liable for damage caused when furniture is shifted without first removing its contents If furniture is shifted we recommend that it is lifted not dragged
Download Pdf Manuals
Related Search