Samsung SW-252 User's Manual
Contents
1. SW 252 en 2003 7 10 66 AM T 4 1 elit CD R RW DRIVE OW 252 User s Guide FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be deter mined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Safety Precautions The following diagrams illustrate the precautions to be taken when using your CD R RW drive Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate th2. Master it will work in the Master mode If the jumper is connected to SL Slave it will work in the Slave mode If the jumper is connected to CS CSEL you can control the device by using the host interface signal CSEL In general connection to MA is recommended MA Master CS Cable Select CSEL pm SL Slave 4 Connecting the audio cable from a sound card e Connect the 4 pin audio cable between the sound output terminal on the CD R RW drive and the audio input terminal on the sound card e For clearer sound use a digital output terminal Available only for the CAID that supports digital output This may not be available for general sound cards Sound Card Sound Output Terminal Digital Output Terminal ee Audio Input Terminal of the Sound Card Installing the CD Record Utility To record data on a CD R or CD RW disc in the CD R RW drive you must first install the CD record utility For compatibility reasons you are recommended to uninstall any existing software of the same type before installing this utility 1 Insert the disc supplied with the CD R RW drive in the drive 2 Follow the instructions displayed on the screen to install the utility Refer to the separate utility documentation for further details 3 Store the utility disc in a safe place Installing the Device Driver Eea No additional device driver is needed for Windows 98 2000 ME XP NT4 0 as the default Windows device driver is us
3. we strongly recommend that you check that Ci digs RW52 32 52 VS your setup meets the system requirements listed below a Item Description 1 2 34 Computer Intel Pentium II or higher 64 MB of RAM or higher with an E IDE interface 1 Connector for stereo headphones with a 3 6 mm stereo mini jack Disk space 700 MB minimum 2 Headphone volume control Windows version Windows 98 2000 ME or XP 3 Emergency eject hole if the compartment does not open when you Windows NT 4 0 or higher press the Eject button power off the computer insert a pin or unfolded paper clip in the hole and push firmly 4 Indicator Light GREEN Read RED Record 5 Disc compartment the compartment opens and closes automatically when you press the Eject button 6 Eject button Important Please read the entire DMA installation guide before installing your CD R RW drive About DMA Installation For stable writing performance at high speeds Installation of DMA transfer mode for E IDE interface is strongly recommended We recommend DMA mode for fast writing DMA Setting Before you install your CD R RW drive we recommend to set DMA to enabled on your Jnr PC system See the following procedure to set DMA transfer mode in windows Ge oprerating system Windows 95 OSR2 98 ME ooo cod dfoooc ccc co ee Click on START Select your CD R RW drive e Click on Settings e Click on the Properties button General DMA Installation Guide Window
4. control on the drive front panel If you select DIGITAL at CD Audio Play in Media Player of Windows ME XP the earphone does not appear in the Digital Mode A CD is not read or is read Check whether the CD is of good quality and clean it too slowly if necessary The disc compartment will Check that the power cable is correctly connected not open Power off and disconnect the PC Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens 14 SW 252 en 2003 7 10 66 AM 4 15 Technical Specifications SAMSUNG continually strives to improve its products Both the design specifications and these user instructions are thus subject to change without notice Meaning Solution When the MPEG software Adjust the size of the replay screen plays a Video CD the Disc types supported CD DA Audio CD ROM CD ROM XA CD Plus pictures are not regular and the running speed is too slow The Disc is not in message is displayed even though a disc has been inserted The CD R RW drive is not detected after it is connected to a sound card IN CD has the Formatted Disc Eject function When recording NERO it will be recorded not on a CD but a form of image file The Recorder cannot recognize the disc After checking the display resolution adjust it if necessary The computer may not recognize the disc if you start playback too quickly afte
5. drive proceed as follows X 1 Push the Push the power button and boot the computer button and boot the computer 2 After booting the computer open the disc compartment compartment by pressing the Eject button pressing the Eject button 3 Insert the disc CD with the label on the disc facing upwards and close the disc compartment by pressing the Eject button The indicator light comes on 4 Play the disc CD Playing Audio CDs Run the CD player supplied with Windows or your sound card You can listen to the CD by connecting headphones to the appropriate connector If you have installed the appropriate player such as Microsoft Windows Media Player you can adjust the volume using the headphone volume control on the drive front panel If you select digital playback in all versions of Windows Media Player p sounds cannot be output to the headphone jack of the product Storing and Cleaning Your Discs To ensure a long service life for your discs and drive follow the pre cautions below when storing and cleaning your discs 1 Do not place a disc in direct sunlight 2 Store a disc vertically in a well ventilated and stable location 3 Do not write or attach a label on a disc 4 Do not drop a disc or place heavy objects on it 5 Do not touch the surface of a disc K hold it by the edges 6 To clean a disc polish lightly from the inside of the disc to the outside with a soft cotton cloth T Do not leave
6. Structure 1 Power cable 2 E IDE cable 3 Master slave select terminal 4 Audio cable SX Sag SS lt I 1 Connecting the power cable The 4 pin power cable from the internal power unit of your computer must be connected to the power terminal on the rear of the CD R RW drive 12V DC Ground 2 0 Ground 5V DC Note An improperly connected power cable may cause trouble Check the direction of the power connector and the incline side of the CD R RW drive before connecting 5 2 Connecting the E IDE cable Insert the IDE cable 40 pin which is connected to the hard disk to the interface terminal Place the red line of the cable close to the Pin 1 When using one E IDE cable Connect the cable to the SL Slave of the Master Slave Select Terminal at the rear of the CD R RW drive Slave Drive Choose the SL Jumper HDD l N Motherboard When using two E IDE cable If there is only one CD R RW drive select MA Master Master Drive Choose the MA Jumper CLE N S SEC 1 Soy a PRIT x HDD Motherboard a Master Drive Choose the MA Jumper Slave Drive Choose the SL Jumper i a WN S Sg is Z Tl D gt v Motherboard HDD Choose the MA jumper Choose the SL jumper 6 SW 252 en 2003 7 10 66 AM 4 7 3 Installing a jumper on the master slave select terminal Connect a jumper to the rear side of the CD R RW If the jumper is connected to MA
7. c 40X 4800KB sec 32X 3600KB sec 24X 2400KB sec 16X 1800KB sec 12X 1200KB sec 8X 6 00KB sec 4X CD RW 4800KB sec 32X 3600KB sec 24X 1500KB sec 10X 600KB sec 4X CD CAV 52 Access Time CD R RW CAV 40 Access Time PIO mode 4 16 6MB sec Multiword DMA mode2 16 6MB sec UDMA mode2 33 3MB sec Access time typical 100ms typical Data Buffer Laser Slide mechanism Spindle motor Load mechanism ERROR RATE FRONT PANEL Eject button Indicator Headphone output Volume control REAR PANEL Required power Interface connector Audio output Jumper block OPERATING Operations ENVIRONMENT Storage GENERAL Dimensions Net weight RELIABILITY MTBF ical 5 VDC 1 5 A Peak 12 VDC 1 5 A Peak Temperature 5 45 C Humidity 10 80 Temperature 25 60 C Humidity 10 90 148 2 W x 42 H x 184 D mm including bezel 750g 100 000 POH Duty 25 16
8. e equipment You must not use the drive in any manner other than that specified in this guide CAUTION WARRANTY PRECAUTIONS Do not attempt to repair the CD R RW drive yourself Contact your dealer or local SAMSUNG representative for all repairs If you make any adjustments or perform any operations other than those specified in this guide you run the risk of exposure to hazardous radiation Avoid exposing your eyes or skin to direct or scattered radiation Please refer to the Samsung limited warranty statements 1 To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture 2 Always check each disc for cracks before using it If there are cracks on the surfaces especially around the border of the center hole we recommend that you make a copy of the disc immediately and then stop using it If you continue using the disc it will probably develop more cracks and eventually cause irreparable damage 3 Do not use poor quality discs e From unknown sources e Without any copyright e Scratched or damaged in any way SW 252 en 2003 7 10 66 AM 4 3 Your CD R RW Drive Upgrading the Firmware Flash Memory 5 6 The product firmware can be upgraded by downloading the updated file from the following Web site http www samsungODD com www samsungelectronics com System Requirements SAMSUNG i compact Before you install the CD R RW drive
9. ed You can check that the CD R RW drive has been correctly detected by Windows To do so proceed as follows 1 Double click on the My Computer icon on your desktop 2 Double click on the Control Panel folder 3 Double click on the System icon 4 Click on the Device Manager tab 5 Expand the CD ROM branch The SAMSUNG CD R RW SW device name is displayed The SAMSUNG device driver enables discs in the CD R RW drive to be read but not recorded in an MS DOS environment the driver is located in the D driver folder on the CD record utility disc SW 252 en 2003 7 10 amp 6 AM 4 9 Setting Up the Device Driver Automatic Setup 1 Insert the setup diskette in the diskette drive and change the directory to A where A is the diskette drive To do so type A after the C prompt and press Enter 2 Type CDSETUP and press Enter 3 Reboot the computer e Manual Setup 1 Make the C SAMSUNG directory 2 Copy the files from the diskette to the C SAMSUNG directory To do so type COPY A C SAMSUNG after the C prompt and press Enter 3 Edit the CONFIG SYS file Add the DEVICE C SAMSUNG SSCDROM SYS D SSCD000 V entry LAST DRIVE Z DEVICE C SAMSUNG SSCDROM SYS D SSCD000 V 4 Edit the AUTOEXEC BAT file Add the C SAMSUNG MSCDEX D SSCD000 entry C SAMSUNG MSCDEX D SSCD000 5 Reboot the computer Using the CD R RW Drive To play audio or video CDs in your CD R RW
10. eliable recording process 5 Use an E IDE cable which has the specified length 46cm Using E IDE cables longer than 46cm may cause errors during data transaction 6 Use only one recording software program To install a software program for recording uninstall any other types or versions of recording software programs first and then reboot the computer Make sure you use the recording software CD Nero Burning Rom Roxio Easy CD Creator provided by us Using our software program with others may cause errors in recording Not compatible with Windows 95 in case of Roxio Easy CD Creator Software 12 aca SW 252 en 2003 7 10 66 AM T 7 13 Recommended Disc Types CD R MCC RITEK CMC SKC BEALL PRODISK MAXELL ACER MPO FUJI TAIYO YUDEN TDK GIGA PLASMON CD RW CD RW 1X 4X RICOH RITEK MCC ACER SKC CMC H S RW 10X RICOH CMC RITEK ACER SKC MCC U S RW 24X_ MCC RITEK Term Description What is Buffer Under Run Every CD R or CD RW drive records the data that the Host PC wants to record until the data flow ends However if the buffer becomes empty temporarily this may cause errors in recording data What is Auto Run If inserting a CD into a drive the operating system executes the Autorun inf file of the CD automatically What is Exaclink This function is to check the buffer to see if there are data while recording If the buffer is empty it waits at the address and then
11. g laser onto a CD If the CD is damaged or recording data is not possible you need to remove the following causes of the error before using the CD It is recommended to set a CD R or CD RW drive as follows 1 Do not work ona multi tasking environment and remove screen savers f you work on a multi tasking environment while the CD RW drive is recording deleting data Buffer Under Run may occur 2 Do not allow any external access to the Host PC while recording data f another user accesses your printer through a network while you are recording data errors may occur 3 Remove the Auto Run function of the CD f you insert a CD that has the Auto Run function to a drive connected to a PC while recording deleting data this may cause errors How to cancel select the Auto Run function Cancel Select the Auto Run function in Start gt Setting gt Control Panel gt System gt Device Manager gt CD ROM Setting p 4 Use image files when you record many small files f you use a lot of small size files for recording this may reduce the transaction rate of the PC Although Exaclink function is often run the recording quality may become low f you copy a CD from another you do not require making available space in the hard disk However when you use image files you need to copy them on the hard disk first and then copy to a CD In this case you need to ensure maximum 700MB of available space in the hard disk for r
12. r inserting the disc Open and close the disc compartment and try again Clean the disc and try again The interface mode of the sound card is AT BUS You must therefore connect the CD R RW drive to the IDE port on the PC mother board rather than to the sound card or install an E IDE compatible sound card Right click the mouse on TRAY ICON right side of the menu bar at the bottom of the monitor and then select Eject to take the CD out Select the drive where the disc is inserted from Windows Explorer Right click the mouse and select Eject to take the CD out This seems to occur when you select the recording function as the system selects Image Recorder instead of SW 252 In this case select a recorder from the menu items at the upper part of NERO and then select SW 252 from the Recorder Selection window When installing the recording software try not to install the software before the ROM drive as this makes the Image Recorder selected Use the firmware automatic upgrade function available at the ODD service website to download the newest firmware and then reinstall the recording software which is included in the bundle www samsung ODD com www samsungelectronics com 15 in read mode CD Extra Photo CD Single Multi session Video CD ready Enhanced CD CD I FMV CD R CD RW CD TEXT CD R CD RW CD RW 120 mm or 80 mm Recording CD R 7800KB sec 52X 7200KB sec 48X 6000KB se
13. restarts recording after the buffer is full You can avoid Buffer Under Run problems by applying the above mentioned principle Solving Technical Problems Meaning Solution The CD R RW drive is not Check that the power audio and IDE cables are detected by the computer correctly connected to the computer Change the IDE cable and reconnect it to the computer Preferably connect a second IDE cable to the CD R RW drive in master mode Check the position of the jumper in the master slave select terminal Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site www samsung ODD com www samsungelectronics com The CD R RW drive is not This case may occur when there is a Windows detected by Windows installation problem reinstall Windows No sound is heard from an Check whether the audio cable is correctly audio CD connected to the sound output terminal on the CD R RW drive and the sound card CD IN terminal After installing the CD R RW drive the PC gets slower The CD R RW drive is not recognized by MS DOS Check that the sound card is operational Adjust the volume control Run the CD player supplied with Windows or your sound card You can listen to the CD by connecting headphones to the appropriate connector If you have installed the appropriate player such as Microsoft Windows Media Player you can adjust the volume using the headphone volume
14. s 98 Me CB e Select Control Panel e Click on the Settings tab 1 2 3 4 5 Select the System Icon Check the DMA checkbox to enables DMA e Select the Device Manager panel Click OK 1 Two pin digital audio output terminal for use with a sound or MPEG card in System Properties Restart your PC supporting digital audio features e Expand the CD ROM icon 2 Four pin sound output terminal for use with a sound card refer to the sound card documentation for further details UTES DUO GS 3 Master slave select terminal Select the DMA mode by selecting Start gt Setting gt Control Panel gt System gt 4 AOpin host E IDE interface connector Device Manager gt IDEATA ATAPI Controller gt Default Assistant IDE Channel 5 4pin power terminal Advanced Information oO SW 252 en 2003 7 10 6 amp 6 AM 4 4 5 Installing the CD R RW Drive To install your CD R RW drive in the PC proceed as follows 1 Make sure that the PC is powered off and disconnected from any power source 2 If necessary attach a horizontal bracket to both sides of the drive e Use of the brackets depends on your computer model you can purchase these accessories separately from your computer dealer 3 Remove the cover from a free expansion slot and install the CD R RW drive as shown in the illustration e f you have no free expansion slot CD R RW install the drive in place of the et diskette drive Supporting
15. the disc compartment open when you are not using it 10 SW 252 en 2003 7 10 66 AM 4 11 Solving Recording Problems If you have any problems recording via your CD R RW drive follow the appropriate instructions below for the source that you are using Hard Drive 1 Check whether the source file is corrupted 2 Optimize the hard disk by using the Windows defragmenter feature START PROGRAMS ACCESSORIES SYSTEM TOOLS DISC DEFRAGMENTER 3 Decompress the hard disk if it is compressed 4 Make sure that the space available on the hard disk is at least twice the size of the largest file to be recorded on the disc 5 it you wish to record more than 1000 small files First create an image file and copy the image file to the disc Choose the low record speed Compress small files and then record them Network Drive 1 Copy the network drive contents to the hard disk and then from the hard disk to the CD R RW drive CD ROM Drive 1 Clean the source CD if necessary 2 Create an image file and then copy the image file to the CD R RW drive 3 Check the CD ROM drive record speed There are two recording methods Low speed file by file High speed transfer of an image file from the hard disk 4 If the transfer speed of the CD ROM drive is slower than the record speed reduce the record speed 11 Caution with errors Every CD R or CD RW drive records data by applying recordin
Download Pdf Manuals
Related Search