Samsung SCC-B531xN User's Manual
Contents
1. Appendix A Specifications for NTSC Standard Item Details Product type CCTV color dome camera Power input AC 24V 10 60Hz 0 3 Hz DC 12V 10 5 Broadcast type NTSC Standard color system 525 Lines 60 Fields Power consumption Approx 1 6W Image device 1 3 inch IT Type Super HAD CCD SCC B5311N B5313N B5315N SCC B5310N Pixels Total 811 H x 508 V 410 000 pixels Effective 768 H x 494 V 380 000 pixels Total 537 H x 505 V 270 000 pixels Effective 510 H x 492 V 250 000 pixels Scanning mode 525 Lines 2 1 Interlace Scanning line frequency Horizontal 15 734Hz INT 15 750Hz LL Vertical 59 94Hz INT 60Hz LL Synchronization mode INT Line Lock Adjusting the phase using INC DEC button Horizontal resolution SCC B5311N B5313N B5315N SCC B5310N 540 TV Lines 330 TV Lines SCC B5311N B5313N B5315N SCC B5310N SOIRE 1Lux 0 6Lux Sens up Off 30IRE 0 6Lux 0 4Lux Min object illumination F20 15IRE 0 3Lux 0 2Lux s SOIRE 0 008Lux 0 005Lux Sens up x128 30IRE 0 005Lux 0 003Lux 15IRE 0 002Lux 0 001 Lux Signal output COMPOSITE Video 1 0 Vp p 750hm BNC Test Monitor OUT 1 0 Vp p 750hm Harness cable Focal length Zone Limit of viewing angle Model Horizontal 92 3 0mm Vertical 72 SCC B5313N Lens Horizontal 71 SC2. bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer 10 11 12 A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces May cause the product and cart combination to overturn O Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions Grounding or Polarization This product may be equipped with a polarized 13 14 15 alternating current line plug a plug having one blade wider than the other This plug will fi
3. direction on the same page Finally attach the Cover dome to the Main body by pressing it until a click sound is heard after aligning the wide groove at the lower part of the Cover dome with the Locker on the Main body Adjusting the camera direction When the camera is fixed on the ceiling you can adjust Panning the camera viewing angle You can rotate your camera leftward or rightward Panning and can change the slope of your camera upward or downward Tilting In case of panning the rotation limit of your camera is set to 340 degree 220 degree clockwise and 120 degree counterclockwise The rotation is stopped by the Stopper inside of the camera For panning control first unfasten two screws located on the bottom and rotate in the direction you want and then fasten them to fix the camera When both fixing screws cannot be tightened change the location of screws When inevitable just tightening one screw is alright In case of tilting you can change the slope of your camera from zero to 90 degree When the slope angle is under 23 degree you can encounter a partial image hide problem To fix the location after adjusting the tilting angle use the Tilt fixing screws To adjust the focus of your camera rotate the fixed lens for clear image When you install the camera on the inclined ceiling or wall you can rotate the camera lens to see a correct direction image SCC B531X
4. it may cause a breakdown or fire When installing your camera don t allow any person to approach the installation site If you have any valuable things under the place move them away Installation procedure gt To install your camera 1 Press the Locker button on the bottom of your camera and remove the Cover dome from the Main body using the other hand The Main body will be exposed to you 2 As shown in the picture push the Lock releaser outward and rotate the Main body in the UNLOCK direction to remove the Mount bracket If it is not easily done rotate the Mount bracket in the LOCK direction while holding small holes on the Mount bracket 3 Fix the Mount bracket to the location ceiling or wall with supplied three screws Ceiling mount Opener Note The CAMERA FRONT sign on the Mount bracket should face the camera monitoring area 13 14 When you install the Mount bracket on the ceiling remove the Ceiling mount opener by pressing it hard to connect the line attached on your camera through the hole in the ceiling Otherwise you can use the empty space opposite to the CAMERA FRONT sign for line connection Now attach the Main body to the Mount bracket by rotating it in the LOCK direction after aligning the Lock releaser on the Main body with the wide groove around the CAMERA FRONT inlay Adjust the camera direction For more details on the direction control see Adjusting the camera
5. such power lines or circuits as contact with them might be atal that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or damaged in any way and f When the product exhibits a distinct 18 Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of 19 Object and Liquid objects of any kin through openings dangerous voltag ire or electric shock Entry Never push d into this product as they may touch e points or short out parts that could result in a fire or electric hock Never spil product 20 Servicing Do noi iquid of any kind on the attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 21 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operat
6. 1 Be sure to use only the standard adapter injury due to fire electric shock or falling that is specified in the specification objects sheet Using any other adapter could 7 Do not install the unit in humid dusty or cause fire electrical shock or damage sooty locations Doing so may cause fire to the product or electric shock 2 Incorrectly connecting the power 8 If any unusual smells or smoke come supply or replacing battery may cause from the unit stop using the product In explosion fire electric shock or damage such case immediately disconnect the to the product power source and contact the service center Continued use in such a condition may cause fire or electric shock 9 10 If this product fails to operate normally contact the nearest service center Never disassemble or modify this product in any way SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair When cleaning do not spray water directly onto parts of the product Doing so may cause fire or electric shock CAUTION 4 gt Do not drop objects on the product or apply strong shock to it Keep away from a location subject to excessive vibration or magnetic interference Do not install in a location subject to high temperature over 122 F 50 C low temperature below 14 F 10 C or high humidity Doing so may cause fire or electric shock If you want to relocate the already installe
7. A D ANTENNA ELECTRIC g SERVICE EQUIPMENT ES connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes andrequirements for the grounding electrode La ANTENNA LEAD IN WIRE DISCHARGE UNIT E NEC SECTION S10 21 92 GROUND CLAMPS ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE 16 Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges NEC SECTION S10 20 GROUNDING CONDUCTORS a POWER SERVICE GROUNDING 17 Povver Lines An outside antenna system should not be located in the vicinity of overhead povver lines or other electric light or povver circuits or vvhere it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching
8. C B5310N Semin Vertical 53 BS311N Horizontal 33 6 8 0mm Vertical 253 SCC B5315N PAN function Range 0 to 340 220 degree clockwise and 120 degree counterclockwise TILT function Range 0 to 90 16 Line Lock LL Sens up Low Speed Shutter LSS Horizontal Reverse H REV Vertical Reverse V REV Backlight compensation BLC Controls Auto gain control AGC Switching between color and B8W by day and night change D N Automatic white balancing AWB Digital noise reduction DNR Dynamic CCD defect compensation Product color SCC B531XN White SCC B531xBN Black Operation temperature 10 C to 50 C Operation humidity Up to 90 Size 102 x 78 H mm Weight 190g SNA Appendix B Specifications for PAL Standard Item Details Product type CCTV color dome camera Power input AC 24V 10 50Hz 0 3 Hz DC 12V 10 5 Broadcast type PAL Standard color system 625 Lines 50 Fields Power consumption Approx 1 6W Image device 1 3 inch IT Type Super HAD CCD Pixels SCC B5311P B5313P B5315P SCC B5310P Total 795 H x 596 V 470 000 pixels Effective 752 H x 582 V 440 000 pixels Total 537 H x 597 V 320 000 pixels Effective 500 H x 582 V 290 000 pixels Scanning mode 625 Lines 2 1 Interlace Scanning line frequency Horizontal 15 625Hz INT 15 625Hz LL Vertical 50Hz INT 50Hz LL Synchronization mode INT Line Lock Adj
9. a Digital Color Dome Camera User s Guide SCC B531x B Nnstiys EXPLANATION OF SAFETY RELATED SYMBOLS CAUTION A RISK OF ELECTRIC A SHOCK DO NOT OPEN The lighting flash and CAUTION TO REDUCE THE RISK The explanation point within Arrowhead within Triangle is OF ELECTRIC SHOCK DO NOT the triangle is a warning sign a warning sign alerting you of REMOVE REAR COVER NO USER alerting you of important dangerous voltage inside the SERVICEABLE PARTS INSIDE REFER instructions accompanying the product TO QUALIFIED SERVICE PERSONNEL product This symbol indicates high voltage 3 Do not connect multiple cameras to a is present inside It is dangerous to single adapter Exceeding the capacity make any kind of contact with any may cause abnormal heat generation or inside part of this product fire This symbol alerts you that important 4 Securely plug the power cord into the literature concerning operation and power receptacle Insecure connection maintenance has been included with may cause fire I this product 5 When installing the camera fasten it g PE securely and firmly A falling camera may To prevent damage which may result in fire cause personal injury or electric shock hazard do not expose this 6 Do not place conductive objects e g appliance to rain or moisture screwdrivers coins metal things etc or containers filled with water on top of the WARNING camera Doing so may cause personal
10. and in case of OFF this camera operates in AWC mode ATW Auto Tracking White Balance The col environmental change Approx 2000 K to 1 AWC Auto White Balance Control It stores lor temperature is automatically adjusted according to the 1 000 K the color temperature just when the switch is changed to OFF Accordingly color temperatures are adj usted by the stored value o ON you can view a clear image even though the 11 I Connecting cables and setting switches Monitor To check the camera view and set the switches To connect cables 1 Connect the BNC cable to the Video connector attached on your camera 2 Connect the BNC cable to the Video Input on a monitor 3 Connect the power adapter to the Power connector attached on your camera When the monitor is turned on the camera image appears 1 Remove the Cover dome For more details about the removing procedures see Installation procedure in the Installing camera section on the next page 2 Adjust the function of your camera using the Switch board while you are viewing the image on the screen 12 I Installing camera Before installation Before installing your camera you have to read the following cautions You have to check whether the location ceiling or wall can bear five times the weight of your camera Don t let the cable to be caught in improper place or the electric line cover to be damaged Otherwise
11. by one degree Switch 2 LSS This sens up mode accumulates the image fields in memory to reduce noise but increase the brightness and co camera automatically switches to a maxi ntrast rate When this switch is set to ON the mum of 128 times of image acquisition speed to implement a clear picture for darker image Switch 3 H REV When this switch is set to ON the camera image is reversed horizontally If you want to monitor your site using a mirror you can use this feature to see the right image Switch 4 V REV When this switch is set to ON the camera image is reversed vertically If your camera reluctantly displays the vertically reversed image you can use this feature to see the right image Switch 5 BLC When this switch is set camera faces any excessive light such as sunlight and fluorescent light When it is set to OFF the subject with excessive light is n Switch 6 AGC When this switch is set ot clearly shown to ON the camera automatically increase the sensitivity by amplifying the video signal when the strength of the signal falls below a given value When any dark images are expec ted use this feature Switch 7 D N When this switch is set to ON the camera automatically switches between color and B amp W according to the brightness of the vicinity Switch 8 AWB This switch adjusts whi te balancing When this switch is set to ON this camera operates in ATW mode
12. d product be sure to turn off the power and then move or reinstall it Remove the power plug from the outlet when then there is a lightning Neglecting to do so may cause fire or damage to the product Keep out of direct sunlight and heat radiation sources It may cause fire Install itin a place with good ventilation Avoid aiming the camera directly towards extremely bright objects such as sun as this may damage the CCD image sensor Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 2 9 The Mains plug is used as a disconnect device and shall stay readily operable at any time FCC Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a res
13. ed in the package Those components are as shown below Test Monitor Cable a lt gt Tab screw Camera User s Guide The test monitor cable is used to test the camera by connecting to a portable display If you really want to connect the camera to a monitoring display use the BNC cable Components of your camera Your camera has the following components Va S Cover dome Covers the lens and main body to protect them Main body Includes a lens a switch board a PCB board screws and such Locker Used to open or close the Cover dome To open the cover dome press the locker Tilt fixing screw Using this screw the slope of the lens can be adjusted and fixed Switch board Includes two kinds of control switches such as function switches and phase control switches The board has eight function switches in the middle and two phase control buttons on each side of the function switch area Lock releaser Push it outward and rotate the main body in UNLOCK direction when you want to remove the mount bracket from the main body Mount bracket Used as a ceiling or wall fixture It is fixed using three long tab screws provided in the package Ceiling mount opener Remove it for line connection to the ceiling when it is installed on the ceiling Installation I Setting switches Setting function switches To set the available f
14. idential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense IC Compliance Notice This Class A digital apparatus meets all requirements of the Canadian interference Causing Equipment Regulations of ICES 003 This device must accept any interference IMPORTANT SAFETY INSTRUCTIONS Read Instructions All the safety and operating instructions should be read before the product is operated Retain Instructions The safety and operating instructions should be retained for future reference Heed VVarnings All vvarnings on the product and in the operating instructions should be adhered to Follow Instructions All operating and use instructions should be followed Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like Accessories Do not place this product on an unstable cart stand tripod brachet or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod
15. ing instructions Adjust only those controls change in performance this indicates a need for service 22 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have he same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 23 Safety Check Upon completion of any service or repairs to this product ask he service technician to perform safety checks to determine that the product is in proper operating condition 24 Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer 25 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat Apparatus shall not be exposed to A dripping or splashing and no objects fil ed with liquids such as vases shall be placed on the apparatus Contents OVET VW comico nat seine 8 Abur IS QUIGO cosuscoscina ica 8 Product overview Main features Components Checking components in the package Components of your camera Installation Setting switches Setting function switches Connecting cables and setting switches Installing camera Before installation Installation procedure Ad
16. justing the camera direction Appendix A Specifications for NTSC Standard 15 Appendix B Specifications for PAL Standard 17 Overvievv I About this guide This user guide includes basic instructions for the product It is recommended that all users read this guide before use me guide is divided as follows m Chapter 1 Overview introduces the user guide and product related information This chapter m Chapter 2 Installation explains how to set and install the product m Appendix Specifications provides the specifications of the product I Product overview This is the high resolution dome camera equipped with a fixed focal lens which has no dynamic delay when implementing motion pictures and provides the features such as digital noise reduction DNR by real time CCD defect compensation low speed shutter LSS Auto x128 to implement clear picture quality Day Night color compensation and the like I Main features m Power DC 12V AC 24V m Special functions Line lock LL control Auto white balancing Horizontal vertical image reversing Auto gain control Low shutter speed control Backlight compensation control Automatic switching between color and black amp white modes Digital noise reduction DNR Dynamic CCD defect compensation I Components Checking components in the package Please check your camera and accessories are includ
17. t into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug Alternate Warnings This product is equipped with a three wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product Protective Attachment Plug The product is equipped with an attachment plug having overload protection This is a safety feature See Instruction Manual for replacement or resetting of protective device If replacement of the plug is required be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug Outdoor Antenna Grounding If an outside antenna or cable system is GROUND AN CLAMP AN
18. unctions on your camera adjust eight switches as shown below Name Brief description 8 LL Line lock ON OFF 7 LSS Sens up or Low speed shutter ON OFF 6 H REV Horizontal reverse ON OFF a V REV Vertical reverse ON OFF 3 BLC Backlight compensation ON OFF 2 AGC Auto gain control ON OFF 1 DIN Automatic switching between color and black amp white ON OFF AWB Automatic white balance ON OFF 1 Switch 1 LL When this switch is set to OFF the camera operates in the internal 10 synchronization mode while when it is set to ON the camera operates in the line lock mode In the internal synchronization mode the camera always uses an inside crystal oscillator for synchronization However if multiple cameras are connected to a sequential switcher picture rolling or flickering may occur when switching from one camera to another In this case you can set this switch to ON to solve this problem The line lock mode allows the camera to use the phase of the AC power as the synchronization reference In this mode you can use the phase control buttons INC DEC When you are using the DC 12V power set this switch to OFF The line lock feature will not normally operate even when the switch is set to ON Set the LL switch to ON while the AC power is connected If any picture roll happens you have to adjust the phase using the phase control buttons Press the INC or DEC button to increase or decrease the phase
19. usting the phase using INC DEC button Horizontal resolution SCC B5311P B5313P B5315P SCC B5310P 540 TV Lines 330 TV Lines SCC B5311P B5313P B5315P SCC B5310P SOIRE 1Lux 0 6Lux Sens up Off 30IRE 0 6Lux 0 4Lux Min object illumination F20 15IRE 0 3Lux 0 2Lux s SOIRE 0 008Lux 0 005Lux Sens up x128 30IRE 0 005Lux 0 003Lux 15IRE 0 002Lux 0 001 Lux Signal output COMPOSITE Video 1 0 Vp p 750hm BNC Test Monitor OUT 1 0 Vp p 750hm Harness cable Focal length Zone Limit of viewing angle Model Horizontal 92 3 0mm Vertical 72 SCC B5313P Lens Horizontal 71 SCC B5310P Semin Vertical 53 B5311P Horizontal 33 6 8 0mm Vertical 253 SCC B5315P PAN function Range 0 to 340 220 degree clockwise and 120 degree counterclockwise TILT function Range 0 to 90 18 Line Lock LL Sens up Low Speed Shutter LSS Horizontal Reverse H REV Vertical Reverse V REV Backlight compensation BLC Controls Auto gain control AGC Switching between color and B8W by day and night change D N Automatic white balancing AWB Digital noise reduction DNR Dynamic CCD defect compensation Product color SCC B531xP White SCC B531xBP Black Operation temperature 10 C to 50 C Operation humidity Up to 90 Size 102 x 78 H mm Weight 190g SNA
Download Pdf Manuals
Related Search