Saeco Coffee Makers saeco HD8833 User's Manual
Contents
1. Water tank Grease for the brew group Pre ground coffee scoop Power cord Intenza Water Filter LED display Optional Aroma Pre ground coffee selector switch Long coffee light button Espresso coffee light button STAND BY light button Hot water steam selector dial INSTALLATION For your safety and the safety of others carefully follow the instruc tions provided in the Safety Regu lations section Machine Packaging The original packaging has been designed and constructed to protect the machine during transport We recommend keeping the packaging material for possible future transport Preliminary Operations Remove the coffee bean hopper cover and the drip tray with grill from the packaging Remove the coffee machine from the packaging and position it in a place that meets the requirements described in the safety regulations Place the drip tray with grill into its appropriate seat on the machine Make sure it is fully inserted to its limit stop e Insert the coffee bean hopper cover Note Insert the plug in the machine and in the wall so cket only when indicated and check that the power button is switched to 0 Important note Carefully read the explanatory descrip tions of all the warnings the machine displays to the user via the lights on the control panel display see section Display Warnings NEVER remove the drip tray when the m2. During the Stand by preparation phase if a coffee product has been brewed e During the phase of activating the stand by mode after pressing the STAND BY button if a coffee product has been brewed A small amount of water will be dispen sed which will rinse and heat all the ma chine components in this phase the but tons SP and EP blink alternately Wait for the cycle to finish automatically You can stop dispensing by pressing either of the two brew buttons 10 INTENZA water filter op tional To improve the quality ofthe used water it is advisable to install the water filter Remove the water filter from its packa ging immerse it vertically with the ope ning positioned upwards in cold water and delicately press the sides so as to let the air bubbles out Remove the small white filter from the tank and store it in a dry place sheltered from dust Set the Intenza Aroma System as specified on the box A Soft water B Medium water standard C Hard water Put the water filter into the empty tank Press it until its limit stop Fill the tank with fresh drinking water and reinsert it into the machine Dispense the water in the tank by using the hot water function see the Hot wa ter dispensing section Fill the water tank again The machine is now ready to be used Note If there is no Intenza water filter insert the small white filter previously
3. appliance and cut the power cord Deliver the appliance and power cord to a service center or public waste disposal facility This product complies with eu directive 2002 96 ec bd The symbol mmm on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 24 25 26 27 PHILIPS The manufacturer reserves the right to change the features of the product without prior notice www philips com saeco Rev 00 del 15 02 13 421940437331
4. better machine performance and operation for its whole operating life If correctly used it also avoids alterations in the brewed product Warning Never drink the descaling solution or any products brewed until the cycle has been carried out to the end Never use vinegar as a descaling solution Before descaling the machine perform the following operations remove the Pannarello if supplied from the steam wand as described in the Cleaning and Maintenance chapter empty the drip tray Place it back in the machine before proceeding Place a large container under the dispensing spout Turn the machine off by pressing the STAND BY button Wait for the machine to complete the rinse process Warning Remove the Inten za filter if installed before adding the descaling solution Note should the containers fill up temporarily suspend the dispensing process in order to empty the containers If descaling solution and or water spills out of the dispensing spout PAUSE turn the selector dial to the wp position START turn the selector dial to the o position If descaling solution and or water spills out of the steam wand PAUSE turn the selector dial to the f position START turn the selector dial to the Ep position 2 Pour the entire content of the Saeco concentrated descaling solution into the water tank and then fill the tank with fresh drinking water up to the MAX level
5. from the socket Wait for the machine to cool down Never immerse the machine in water Itis strictly forbidden to tamper with the internal parts of the machine Water left in the tank for several days should not be consumed Wash the tank and fill it with fresh drinking water If the machine will not be used for a long time dispense water from the steam wand and carefully clean the Pannarello if supplied then turn it off and unplug it Store it in a dry place out of the reach of children Keep it protected from dust and dirt Servicing Maintenance In case of failure problems or a suspected fault resulting from the falling of the machine im mediately remove the plug from the socket Never attempt to operate a faulty machine Servicing and repairs may only be carried out by authorized service centers All liability for damages resulting from work not carried out by professionals is declined Fire Safety Precautions In case of fire use carbon dioxide CO extinguishers Do not use water or dry powder extin guishers 5 Grinder adjustment Coffee bean hopper Coffee bean hopper cover knob Control panel N ii le Dispensing spout Pre ground coffee compartment Cup holder grill lt K L o lt Si Full drip tray indicator gt SS Brew group Service door Coffee grounds drawer Wand protective gripper Hot water steam wand ON OFF power button Sy OSaeco
6. place Clean the Pannarello Change coffee blend or adjust the grind as explained in the Coffee Grinder Adjustment section Descale the machine Turn the machine on Close the service door and insert the coffee grounds drawer The brew group automatically returns to the initial position Coffee grounds drawer is inserted Water tank is empty Remove the coffee grounds drawer first then the brew group Fill the water tank and prime the circuit section Using the Machine for the First Time Brew group is dirty Clean the brew group section Brew Group Circuit is not primed Prime the circuit section Using the Machine for the First Time Rare event that occurs when the machine is auto matically adjusting the dose Brew a few coffees as described in section Saeco Adapting System The dispensing spout is dirty Rare event that occurs when the machine is auto matically adjusting the dose The coffee grind is too fine Clean the dispensing spout Brew a few coffees as described in section Saeco Adapting System Change coffee blend or adjust the grind as ex plained in the Coffee Grinder Adjustment sec tion The circuit is not primed Prime the circuit section Using the Machine for the First Time The brew group is dirty The dispensing spout is clogged Clean the brew group section Brew Group Clean the dispensi
7. removed into the water tank ADJUSTMENTS The machine that you have bought allows for certain adjustments that will permit you to use it to its full potential Saeco Adapting System Coffee is a natural product and its cha racteristics may change according to its origin blend and roast The Saeco coffee machine is equipped with a self adjusting system that allows the use of all types of coffee beans available on the market non caramelized The machine automatically adjusts itself in order to optimise the extrac tion of the coffee ensuring perfect compression of the tablet to obtain a creamy espresso coffee that will release all the aromas regardless of the type of coffee used The optimisation process is a learning process that requires the brewing of a certain number of coffees to allow the machine to adjust the compactness of the ground coffee e Attention should be given to spe cial blends which require grinder adjustments in order to optimise the extraction of the coffee see the Coffee Grinder Adjustment section Coffee Grinder Adjustment Warning The grinder adjustment knob inside the coffee bean hopper must be turned only when the grinder is working Do not pour ground and or instant coffee into the coffee bean hopper Do not insert any material other than coffee beans into the hopper The grinder contains moving parts that may be dangerous Therefore do not insert fingers and or oth
8. the milk clean the steam wand or Pannarello when provided When the machine is ready brew a small amount of hot water in a glass and clean the steam wand or Panna rello when provided externally In this way all parts will be perfectly cleaned and free of any milk residue To prepare your cappuccino we recommend discharging the water in the steam wand To discharge the water in the steam wand place a container under the steam wand Pannarello if supplied When the machine is ready to brew coffee turn selector dial counter clockwise to set it onto the amp po sition Residual water may come out of the steam wand Pannarello if supplied The and SP lights blink during the preheating time required by the machine Note The lights that indica te the aroma are off when dispensing steam Steam dispensing will begin when the buttons SP and are displayed steady on soon after only steam will begin to come out Turn the selector dial clockwise and set it back to the position to stop dispensing steam Fill 1 3 of the container you wish to use CLEANING AND MAIN NCE to prepare the cappuccino with cold TENA milk General Cleaning Empty and clean the coffee grounds drawer daily with the machine turned on To ensure better results when preparing a cappuccino use cold milk straight from the fridge Note We recommend emptying the container if t
9. touch it with wet hands Do not let the power cord hang freely from tables or shelves For the Safety of Others Keep children under control to prevent them from playing with the product Children are not aware of the risks related to electric household appliances Do not leave the machine packaging materials within the reach of children 6 inches 150 mm 6 inches Danger of Burns Never direct the steam hot water wand towards yourself or others Danger of scalding Al ways use the handles or knobs provided Machine Location Suitable Location for Operation and Maintenance For best use it is recommended to Choose a safe level surface where there will be no danger of overturning it or being inju red Choose a location that is sufficiently well lit clean and near an easily reachable socket Provide for a minimum distance from the sides of the machine as shown in the illustration During machine turning on off it is recommended to place an empty glass under the ddi spensing spout Do not keep the machine at a temperature below 0 C 32 F Frost may damage the machine Do not use the coffee machine outdoors In order to prevent its housing from melting or being damaged do not place the machine on very hot surfaces and close to open flames Storing the Machine Cleaning Before cleaning the machine turn it off by pressing the STAND BY button and then switch the power button to 0 Remove the plug
10. Pannarello for standard cleaning Remove the upper part of the Pannarello from the steam wand Wash the upper part of the Pannarello with fresh drinking water Wash the steam wand with a wet cloth and remove any milk residue Replace the upper part in the steam wand make sure it is completely inserted Reassemble the external part of the After using steam to prepare a beverage it is possible to brew coffee or to dispense steam straight after If the selector dial is left on the central position p the machine in order to save energy au tomatically reaches the temperature needed to dispense coffee lt T5 le Pannarello We recommend cleaning the water tank daily For an easier removal of the water tank move the steam wand Pannarello upwards Remove the small white filter in the water tank and wash it under running drinking water Reposition the small white filter in its housing by gently pressing and turning it at the same time Fillthe water tank with fresh drinking water Empty and clean the drip tray daily Perform this operation also when the float is raised Also clean the seat of the tray every week through the openings on the bottom of the machine Brew Group The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week Turn off the machine by pressing the ON OFF button and remov
11. Place the tank back in the machine 3 Make sure the selector dial is in the P position 4 Press and hold the 2 brew buttons at the same time for 3 seconds the descaling cycle is started 17 5 N after start up the machine needs circuit priming turn the selector dial clockwise to the amp position When Fa Note if the button y lights up steady immediately the A icon is displayed turn the selector back to a position The O light blinks quickly to show the machine has entered the descal ing automatic programme when the light is steady the 1 limescale removal phase is on Place an empty container under the steam wand and another one under the dispensing spout When the button is lit up steady turn the selector dial clockwise to the g position in this case the steam hot water wand starts dispensing the descaling solution at regular intervals When the descaling solution in the water tank is finished the A light starts blinking Turn the selector dial to the posi tion Empty the container under the steam wand and the one underthe dispensing spout 10 When the Y icon lights up steady on the display remove the water tank 11 Remove the water tank rinse it and fill it up to the MAX level with fresh drinking water 12 Place the tank back in the machine The 0 light turns on steady to show the machine has entered the rinse phase 13 Place an
12. Register your product and get support at www philips com welcome SYNTIA Type HD8833 SUP 037R OPERATING INSTRUCTIONS READ THESE OPERATING INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE Saeco IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 2 3 8 9 Read all instructions Do not touch hot surfaces Use handles or knobs To protect against fire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid Close supervision is necessary when the appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons Do not use outdoors Do not let cord hang over edge of table or counter or touch hot surfaces 10 Do not place on or near a hot gas or electric burner or in a heated oven 11 Always attach plug to appliance first then plug cord into wall outlet To disconnect turn any contro
13. achine is turned on Wait a couple of minutes after turning on off as the machine will be carrying out a rinse self cleaning cycle see section Rinse Self clea ning Cycle ILAT Lal Remove the water tank from its seat e Rinse and fill it with fresh water ma king sure that it is not filled exceeding the MAX level indicated in the water tank Put the water tank back in its seat Fill the tank only with fresh non sparkling water Hot wa ter or any other liquid may damage the tank and or the machine Do not turn on the machine when the tank is empty Make sure there is enough water in the tank Remove the coffee bean hopper cover Note The hopper may be provided with different sa fety features according to the regu lations of the country of use of the machine Slowly pour the coffee beans into the hopper Only coffee beans must be put into the coffee bean hopper Ground coffee instant coffee or any other object may damage the machine Replace the coffee bean hopper cover e Insert the plug into the socket on the back of the machine Insert the plug of the other end of the cable into a wall socket with suitable power voltage ae Switch the power button to I to turn the machine on e The STAND BY button blinks Make sure the selector dial is in the position if this is not the case set it to that position Toturn the machine on simply p
14. ble power supply cord or extension cord is used 1 The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 If the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over GENERAL INFORMATION The coffee machine is suitable for preparing espresso coffee using either coffee beans or ground coffee and is equipped with a device to dispense steam and hot water The structure of the ma chine has been designed for domestic use only and is not suitable for continuous professional type operation Keep these operating instructions in a safe place and make them available to anyone who may use the coffee machine For further information or in case of problems that are not included or not completely explained in these instructions please contact an authorized service center A Warning No liability is held for damage caused by Incorrect use not in accordance with the intended purposes Repairs not carried out by authorized service centers e Tampering with the power cord Tampering with any parts of the machine Storage or use of the machine at a temperature outside the operating temperature range 15 C 45 C The use of non o
15. ble the external part of the Pan narello The descaling cycle is complete Start the machine as described in the manual and perform normal warm up and rinse operations the machine is now ready for product brewing If the machine is switched off during the descaling cycle next time the machine is switched on the cycle must be repeated from the point it has been paused 19 The descaling solution is to be disposed of according to the manufacturer s instructions and or the regulations in force in the country of use After completing the des caling cycle wash the brew group as described in the Brew Group section in the Cleaning and Maintenance chapter Remarks on descaling The previous section explains the correct operations to perform to descale the machine The machine you have purchased is equipped with advanced software to check the quantity of used water in order to provide reliable information about the right time to carry out descaling opera tions This software has been programmed for standard water hardness In case of especially hard water high calcium content descaling cycles might have to be carried out more frequently even if the machine does not display warning signals Even if the machine is not used often e g 1 coffee per day it is recommended to perform descaling cycles more frequently In these specific cases it is recommended to perform descaling cycles every 1 2 m
16. e machine ca refully follow the instructions provided Using the machine for the first time or after a long period of inactivity These simple operations will make it pos sible to always brew excellent coffee 1 Place a large container under the dispensing spout 2 Before starting the procedure check that the following icon is displayed and that the buttons SP and SP on the control panel are steady on 3 Select the pre ground coffee function by pressing the 2 button one or more times Do not add the pre ground coffee to the compartment The icon will appear on the display 4 Press the button to brew a long cof fee 5 Wait until brewing is completed and empty the container 6 Repeat the operations from step 1 to step 5 for 3 times then continue with step 7 7 Place a container under the steam wand Pannarello if supplied 8 Turn the selector dial clockwise to set it to the position A Blinking 9 Dispense water until the no water si gnal is displayed then turn the selec tor dial counter clockwise to set it to the Y position 10 At the end fill the water tank again Then the products can be brewed as described in the following sections Rinse Self cleaning Cycle This cycle allow rinsing the coffee circuits with fresh water The cycle is carried out At machine start with cold boiler After priming the water circuit with cold boiler
17. e the plug from the socket Remove the coffee grounds drawer Open the service door Toremove the brew group pull it by the handle and press the PUSH button The brew group must be washed only with lukewarm water with no deter gent soap Wash the brew group with lukewarm water and carefully clean the upper filter Thoroughly wash and dry all the parts of the brew group Thoroughly clean the inside of the machine Make sure that the two reference signs match up e Make sure that the lever is in contact with the brew group Press the PUSH button to make sure that the brew group is in the correct position Lubricate the brew group every 30 days or after ap proximately 500 brewing cycles The grease to lubricate the Brew Group can be purchased at authorised service centres Lubricate the brew group guides using the supplied grease only Apply the grease evenly on both side guides e Insert the brew group in its seat until it locks into place WITHOUT pressing the PUSH button Insert the coffee grounds drawer Close the service door DESCALING Limescale normally builds up with the use ofthe appliance The machine must be descaled when the icon appears on the display Do not turn the machine off or put it in stand by mode during the descaling process Usethe Saeco descaling prod uct only Its formula has been designed to ensure
18. empty container under the steam wand and another one under the dispensing spout When the Pn button is lit up steady turn the selector dial clockwise to the Sp position 14 When the A light is blinking turn the selector dial to the 7 position 15 When the button is lit up steady turn the selector dial clockwise to the g position in this case the steam hot water wand dispenses the rinsing water continuously 16 When the rinsing water in the water tank is finished the AN light starts blinking 17 Turn the selector dial to the posi tion Empty the container under the steam wand and the one under the dispensing spout 18 When the 4 icon lights up steady on the display remove the water tank 19 Remove the water tank rinse it and fill it up to the MAX level with fresh drinking water 20 Place the tank back in the machine Place an empty container under the steam wand 21 When the Pn button is lit up steady turn the selector dial clockwise to the p position The second rinse cycle is started 22 When the second rinse cycle is over the machine enters the stand by mode and the CD button starts blinking Empty the container under the steam wand and the one under the dispensing spout If the tank is not filled up to the MAX level the cycle must be repeated from point 16 23 Turn the selector dial to the P posi 24 At the end refill the water tank Reassem
19. enter the programming mode the button E blinks together with the lights of the display shown in the figure and the coffee will start to be brewed These light signals remain active during the whole cycle Press the gt button again when the amount of coffee in the cup reaches the desired level oo Steady on At this point the button P is program med each time it is pressed and released the machine will brew the same amount of coffee that was just programmed Stand by The machine is designed for energy sa ving The machine automatically turns off after 30 minutes of inactivity They button blinks when the machine isin stand by mode Note During the turning off phase the machine performs a rinse cycle if a coffee product has been brewed Warning When turning the machine on after it has been turned com pletely off the machine will be in stand by mode To turn the machine on again simply press the STAND BY button if the power but ton is set to I In this case the machine will go through the rinse cycle only ifthe boiler is cold COFFEE BREWING Note Shouldthe machine not brew coffee make sure that the water tank contains water Before brewing coffee check the lights on the display and on the control panel Check that the water tank and the coffee bean hopper are full Leave the selector on the coffee position 4 during the dispensing phase Before brewing
20. er objects The grind setting may only be adjusted using the knob Turn off the machine and unplug it from the socket before carrying out any type of operation inside the coffee bean hopper Do not pour coffee beans when the coffee grinder is working o yo 0 7 The machine allows slight adjustments to the coffee grinder to adapt it to the kind of coffee used To make any adjustment press and turn the knob inside the coffee bean hopper Press and turn the knob by one notch at a time and brew 2 3 cups of coffee this is the only way to notice differences in grind The reference marks inside the coffee bean hopper indicate the grind setting There are 5 different grind settings to cho ose from with the following references Large Mark Coarse Grind Small Mark Fine Grind Adjusting the Coffee Length The machine allows you to adjust the amount of brewed coffee according to your taste and or the size of your cups Each time the E or buttons are pressed and released the machine brews a pre set amount of coffee as per factory settings This amount may be reprogram med to your taste Each button may be individually programmed for a specific brew setting As an example the following procedure describes the programming of the but ton 2 which is normally associated with espresso coffee Place a cup under the dispensing spout Hold the SS button pressed for 5 seconds to
21. fee bean hopper After refilling the hopper the cycle can be restarted Fill the water tank e OUT OF SERVICE Turn off the machine using the power button on its back and turn it on again If the error persists contact the service centre TROUBLESHOOTING Machine Actions The machine does not turn on The coffee is not hot enough No hot water or steam is dispensed The coffee has little crema see note The machine takes a long time to warm up or the amount of water dispensed from the wand is too little The brew group does not come out The machine grinds the coffee beans but no coffee comes out see note The coffee is too weak see note Coffee is brewed slowly see note Coffee leaks out of the dispensing spout Note These problems can be considered normal if the coffee blend has been changed or if the machine has just been installed Causes The machine is not connected to the power source The cups are cold The hole of the steam wand is clogged Solutions Connect the machine to the power source Warm the cups with hot water Clean the hole of the steam wand using a pin Make sure that the machine is turned off and has cooled before performing this ope ration Pannarello is dirty if supplied The coffee blend is unsuitable the coffee is not freshly roasted or the grind is too coarse The machine circuit is obstructed by limescale build up The brew group is out of
22. fun ction for brewing coffee with pre ground coffee is displayed This selection is displayed by the icon on the side Refer to the relevant section to use this function Using Coffee Beans To brew coffee press and release the button to select the desired aroma the amp button for an espresso cof fee the button for a long coffee The brewing cycle then starts To brew 1 cup of coffee press the SP or E button once The pressed button will be steady on To brew 2 cups of coffee press the EP or SP button twice consecutively The pressed button will blink quickly To brew 2 coffees the machi ne automatically grinds and doses the correct amount of coffee Brewing two coffees requires two grinding cycles and two brewing cycles which the machine carries out automatically After the prebrewing cycle coffee begins to come out of the dispensing spout e Coffee brewing stops automatically when the pre programmed level is reached however it is possible to in terrupt coffee brewing by pressing the button initially pressed The machine is adjusted to brew a true Italian espresso coffee This feature may slightly lengthen the brewing time allowing the intense flavour of the coffee to develop fully Using Pre ground Coffee This function allows using pre ground and decaffeina ted coffee Pre ground coffee must be poured into the appropr
23. he machine is not going to be used Immerse the steam wand Pannarello for some days it supplied inthemilkto be heated e Maintenance and cleaning operations can only be carried out when the ma chine is cold and disconnected from the electric network Do not immerse the machine in water Donot wash any of the removable parts in the dishwasher Turnthe selector dial counter clockwise tosetit to the position Rotate the container and move it gently up and down to obtain uniform foam Do not use sharp objects or harsh che mical products solvents for cleaning e Useasoft dampened cloth to clean the machine Do not dry the machine and or its components using a microwave and or standard oven After dispensing steam for the desired time turn the selector dial clockwise and set it back to the Y position to stop dispensing steam After preparing milk bevera ges dispense hot water from the steam wand Pannarello if sup plied to obtain a thorough cleaning Thesame procedure can be used to heat other beverages Everyday after heating the milk remo After using the steam wand Pannarello E ve the external part of the Pannarello if supplied wash it as described in the if supplied and wash it with fresh Cleaning and Maintenance section drinking water Clean the steam wand weekly In order to do this perform the following ope rations Remove the external part of the
24. iate compartment positioned next to the coffee bean hopper Only use ground coffee for espresso machines and never coffee beans or instant coffee il Note If no pre ground coffee is poured into the compartment only water will be dispensed If the dose is excessive and 2 or more measuring scoops of coffee are used the machine will not brew the product Also in this case the machine will run an empty cycle and discharge any ground coffee into the coffee grounds drawer To brew coffee Press and release the button until the pre ground coffee function icon is displayed Lift the pre ground coffee compart ment cover Add 1 only 1 scoop of pre ground coffee to the compartment Use the measuring scoop supplied with the machine to perform this operation Then close the cover Warning Only add pre ground coffee to the compartment Other substances and objects may cause severe damage to the machine This damage will not be covered by warranty Press and release the button for an espresso cof fee the gt button for a long coffee The brewing cycle then starts After the prebrewing cycle coffee begins to come out of the dispensing spout Coffee brewing stops automatically when the pre programmed level is reached however it is possible to in terrupt coffee brewing by pressing the button initially pressed After dispensing the product the cof fee beans configu
25. l to off then remove plug from wall outlet 12 Do not use appliance for other than intended use 13 Save these instructions SAVE THESE INSTRUCTIONS CAUTION This appliance is for household use only Any servicing other than cleaning and user maintenance should be performed by an authorized service center Do not immerse machine in water To reduce the risk of fire or electric shock do not disassemble the machine There are no parts inside the machine serviceable by the user Repair should be done by authorized service personnel only 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage Never use warm or hot water to fill the water tank Use cold water only Keep your hands and the cord away from hot parts ofthe appliance during operation Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water For optimal taste of your coffee use purified or bottled water Periodic descaling is still recommended every 2 3 months Do not use caramelized or flavored coffee beans INSTRUCTIONS FOR THE POWER SUPPLY CORD A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may used if care is exercised in their use If a long detacha
26. ng spout and its holes In this case wait until the machine performs a self adjusting operation as described in section Saeco Adapting System Please contact Saeco Customer Service or an authorized service center for any problems not covered in the above table or when the suggested solutions do not solve the problem 230 TECHNICAL SPECIFICATIONS The manufacturer reserves the right to make changes to the technical specifications of the product Nominal Voltage Power Rating Power Supply 2 eee eee eee e seen eee eee eee eee eeetet ene nen See label on the inside of the service door Housingimaterlall cosmos dron ea nee Thermoplastic material Metal Size wx h x d 10 x 12 5 x 16 256 x 315 x 415 mm Welt aan ae re ee en ERNEUERT ER 20 Ibs 9 kg Power Cordilength ia ann nenn era een 47 1 2m Control Panel nissan een ade as ee een Front side Pannarello only available for certain models 0 ccs eee cece eee e eee ee ene e eee eneeneennenaes Water tank weiss acsciaatexac dase aan le naar re een een Coffee Bean Hopper Capacity accessi niiina ana inene nana EE EER Aai aeg Special for cappuccinos 1 2 litres Removable type acne 9 2 oz 260 g Coffee qrounds drawer Capa cia ee ee 8 A NT 15 bar A NA Stainless steel type Safety Mecha nis MS in rana AA Ri a e AA AAEE EAEKO UES to Thermal fuse MACHINE DISPOSAL The packing materials can be recycled Appliance Unplug the
27. onths even if the machine does not signal it oo CONTROL PANEL DISPLAY Ready Signals Steady on Steady on EI The machine is ready for brewing coffee from bean and hot water dispensing The machine is ready for pre ground coffee brewing The machine is brewing 1 cup of espresso coffee The machine is brewing 2 cups of espresso coffee The machine is brewing 1 cup of long coffee The machine is brewing 2 cups of long coffee o yn op Blinking The machine is programming the amount of coffee to be brewed for each espresso coffee e The machine is programming the amount of coffee to be brewed for each long coffee 21 Blinking A Fast Blinking 22 CONTROL PANEL DISPLAY Warning Signals The machine is warming up to brew coffee and dispense hot water or steam The machine is performing the rinse cycle Wait until the machine stops the opera tion The machine needs a descaling cycle The machine needs water circuit priming Brew group overstressed The coffee cycle will be interrupted Perform a coffee cycle again A Slow Blinking ba Es a no a Aw Alarm Signals Return the hot water steam knob to its correct position Insert the brew group in the machine Close the service door e Empty the coffee grounds drawer Insert the coffee grounds drawer No coffee beans in the cof
28. ration of the machi ne is restored Repeat the operations de scribed above to brew other coffees DISPENSING HOT WATER Warning At the beginning short spurts of hot water may come out Danger of scalding The hot water wand may reach high tempera tures Never touch it with bare hands Before dispensing hot water check that all the lights on the display and on the control panel are on When the machine is ready proceed as follows e Placeacontainer under the steam wand Pannarello if supplied 13 Blinking 14 Turn the selector dial clockwise to set it to the position Note The lights that indica te the aroma are off when dispensing hot water Fill the cup with hot water to the desi red level to stop hot water dispensing turn selector dial counter clockwise back to the position The machine returns to the normal operating mode Occasionally after turning the selector dial hot water may not be dispensed and the but tons will start blinking Simply wait until the end of the warm up phase so that hot water can be dispensed from the Pannarello STEAM DISPENSING lida Steam may be used to froth milk for a cappuccino as well as to reheat other beverages Danger of scalding Brewing may be preceded by small jets of hot water The steam wand may reach high temperatures Never touch it with bare hands Important note immediately after using the steam to froth
29. ress the STAND BY button The blinking icons shown to the side warn that the circuit must be primed Note Before starting the machine for the first time and after long periods of inactivity prime the water circuit oo Steady on 7 Circuit Priming e To prime the water circuit place a container under the steam wand Pannarello if supplied Turn the selector dial clockwise to set it tothe gt position The machine starts the automatic priming of the circuit by letting out a preset quantity of water through the Pannarello Once the circuit has been primed the icon shown in the figure will start blinking on the display Turn the selection knob back to its 4 central position Y The buttons EP and E on the control panel blink slowly together to show that the machine is warming up When warm up is complete the machine performs a rinse cycle of the internal circuits During this phase the buttons E and blink alternately When the operations described above are completed the buttons EP and are steady on and the aroma icon on the display turns on The displayed aroma is the factory setting when the machine is switched on for the first time or it is the same as the aroma that was selected for the last brewed coffee The machine is then ready to brew beverages To brew coffee dispense hot water or steam and properly use th
30. riginal spare parts and accessories In these cases the warranty shall be deemed null and void SAFETY REGULATIONS Never allow water to come into contact with any of the electrical parts of the machine Danger of short circuit Steam and hot water may cause scalding Do not direct the steam hot water wand towards body parts Carefully handle the steam hot water wand by its grip Danger of scalding Intended Use The coffee machine is intended for domestic use only Do not make any technical changes or use the machine for unauthorized purposes since this would create serious hazards The appliance is not to be used by persons including children with reduced physical mental or sensory abilities or with limited experience and or expertise unless they are supervised by a person responsible for their safety or they are instructed by this person on how to properly use the machine Power Supply Power Cord Only connect the coffee machine to a suitable socket The voltage must correspond to that indicated on the machine label located on the inside of service door Never use the coffee machine if the power cord is defective or damaged If damaged the power cord must be replaced by the manufacturer or an authorized service center Do not pass the power cord around corners over sharp edges or over hot objects and keep it away from oil Do not use the power cord to carry or pull the coffee machine Do not pull out the plug by the power cord or
31. the coffee adjust the height of the di spensing spout according to your needs and select the aroma or the pre ground coffee 11 Dr i no 19 Dispensing Spout Adjustment Most cups on the market can be used with this coffee machine The height of the dispensing spout may be adjusted to better fit the dimensions of the cups that you wish to use Manually move the dispensing spout up or down to adjust its height by placing your fingers as shown in the figure The recommended positions are For use with small cups For use with large cups e Two cups can be placed under the dispensing spout for brewing two coffees at the same time Aroma Adjustment The machine is set up for an amount of coffee to grind to be adjusted from 7 g to 10 5 g per coffee Four choices are possible by pressing and releasing the 2 button mild medium or strong aroma and pre ground coffee Selection can be made when the beans appear on the display Each time the button is pressed and released the aroma changes by one degree Mild aroma Medium aroma 0 0 Strong aroma Quick blinking 2 cups of espresso HE Y LO All gt Quick blinking 2 cups of coffee Selection must be made prior to selecting the coffee The system sets the aroma ac cording to the personal taste of the user After selecting Strong aroma the
Download Pdf Manuals
Related Search