Rosewill RMS-MT3710 User's Manual
Contents
1. _ M Small Spacer x4 ia N Large Spacer x4 LL O Me Washer x4 O P Concrete Q M8x63 R R Lag Bott BS FF anchor 6 SSF Lag Bolt x6 ue Washer x6 RResewill RMS MT3710 Universal Tilting Wall Mount User Manual Part 1a Mounting the Wall Plate Drywall Important For safety this mount must be secured to two adjacent wood studs at least 16 apart 1 Using a stud finder locate and mark two adjacent studs for securing the mount 2 Place the wall plate against the wall and level it using the bubble guide Mark four locations two per stud on the wall where the mount will be secured Be sure to use the center of each stud 4 Remove the wall plate and drill a 1 4 6 mm pilot hole at each location using an electric drill With the help of another person replace the wall plate and fix it to the wall using the Lag Bolts Q and Lag Bolt Washers R provided Fig 1 Do not over tighten the bolts and do not release the wall plate until all screws are secure 7 Attach the cable manager to the middle of the top crossbar Fig 2 o a Fig 1 Attach the wall plate to the wall a Part 1b Mounting the Wall Plate Concrete 1 Place the wall plate against the wall and level it using the bubble guide 2 With the help of another person mark off six 6 locations for fixing the mount to the wall 3 Place the wall plate aside and drill a hole at each location usin2. a Fig 6 A small padlock can be used to help Fig 7 Loosen the adjustment knobs to prevent theft of your display change the tilt angle There is one knob on each side of the mount Thank you for purchasing a quality Rosewill Product Please register your product at www rosewill com for complete warranty information and future support for your product 4
3. 4 You will need to use the M6 Washers O if you are using the M4 M5 or M6 bolts If your display has a curved or recessed back you may also need to Fig 3 Attach the arms to the back use a Spacer M or N penal 4 Make sure the screws are snug but do not over tighten For displays with flat For displays with curved backs or recessed backs Fig 4 Use a longer bolt and spacer for displays with curved or recessed backs Do not use the M6 Washer O if you are using the M8 Bolts J or K Flosewill RMS MT3710 Universal Tilting Wall Mount User Manual Part 3 Final Installation and Adjust ment With the help of another person carefully lift your display and place it on the wall plate Fig 5 Do not release the display until the mounting arms have securely hooked onto the crossbars Move the safety tab located on each arm into position to avoid having the display accidentally lifted from the mount A padlock can be inserted into one of the tabs to help prevent theft of your display Fig 6 The cable manager can be used to keep your power cord and other A V cables in order To adjust the tilt position have one person hold the display in position while another person ys ante ee me loosens the two tilt adjustment knobs located on either side of the wall plate Fig 7 Once the knobs are loose move the display to the desired angle Re tighten the knobs before releasing the display N o
4. Flosewill RMS MT3710 Universal Tilting Wall Mount User Manual Tools Required Phillips Head Screwdriver e Ratchet or Driver with 1 2 13 mm Socket Portable or Electric Drill 1 4 6 mm Drill Bit and Stud Finder for Drywall Installation 7 16 11 mm Masonry Bit for Concrete Installation Warnings 1 Make sure these instructions are read and completely understood before attempting installation If you are unsure of any part of this installation contact a professional installer for assistance 2 The wall or mounting surface must be capable of supporting the combined weight of the mount and the display otherwise the structure must be reinforced 3 Safety gear and proper tools must be used A minimum of two people are required for this installation Failure to use safety gear and or attempting this installation alone can result in property damage serious injury or death 4 Follow alll instructions and recommendations regarding adequate ventilation and suitable locations for mounting your display Consult the owner s manual for your display for more information Hardware Kit Ref Item Qty Jammu A Max12 Bott x4 SB M430 Bolt x4 C M4 Lock Washer x4 Rewer D M5x12 Bolt x4 GEE MO Bot x4 F M5 Lock Washer x4 wail Maxi2 Bot oa NOTON Meas Bott 4 SE WMG Lock Washer x4 emma ereeereneercenerne renee een MBx16 Bott x4 pl 4 Max40 Bot xa SPE L MB Lock Washer x4
5. g a 7 16 11 mm masonry bit Remove any excess dust from the holes Insert one Concrete Anchor P into each hole A hammer can be used to lightly tap the anchors into place if necessary With the help of another person replace the wall plate and fix it to the wall using the Lag Bolts Q and Lag Bolt Washers R provided Fig 1 a a 6 Do not over tighten the screws and do not Fig 2 Attach the cable manager release the wall plate until all screws are secure to the top crossbar 7 Attach the cable manager to the middle of the top crossbar Fig 2 esewill RMS MT3710 Universal Tilting Wall Mount User Manual Part 2 Attaching the Arms to the Display Important Use extra care during this part of the installation Avoid laying your display face down if possible as it may damage the viewing surface 1 Examine the back of your television If the back of your display is flat you will be using one of the shorter bolts from the hardware kit If the back of your display is curved or recessed you will be using one of the longer bolts and a spacer Fig 4 2 Determine the correct diameter bolt to use by trying one bolt each from Bags 1 4 of the hardware kit Do not force any of the bolts if you feel resistance stop immediately to avoid damaging your display 3 Attach the arms to the back of your display using the bolts identified in Steps 1 and 2 and the corresponding Lock Washer C F or L Fig
Download Pdf Manuals
Related Search