Rosewill RMS-MT2790 User's Manual
Contents
1. LCD MONITOR WALL MOUNT RMS MT2790 User Manual RMS MT2790 User Manual Part 1B Installing the Wall Plate Concrete IMPORTANT For safety reasons the concrete wall must be capable of supporting the combined weight of the mount and the display Place the wall plate against the wall in the desired location and level it using the integrated bubble level Mark the two holes for securing the mount and set the wall plate aside Drill a5 16 8 mm hole at both marked location Remove any excess dust from the holes insert a Concrete Anchor P into each hole so that it is flush with the concrete surface A hammer can be used to lightly tap the anchors into place if necessary NOTE If the concrete wall is covered by a layer of plaster or drywall the concrete anchor must pass completely through the layer to rest flush with the concrete surface RMS MT2790 User Manual SPECIFICATIONS Display Size 13 to 27 Maximum Load 44 Ibs 20 kg Mounting Pattern VESA 75 or VESA 100 Tilt Range 13 8 Pan Swivel Range 70 Horizontal Rotation 360 Extension Profile 9 5 cm 3 7 BOX CONTENTS Q Tilt Wall Mount x1 O Wall Plate x1 Q Instruction Manual x1 Q Hardware Kit x1 eS SS a SS RMS MT2790 Part 1B Installing the Wall Plate Concrete continued Move the wall plate back into position and secure it using the Drywall Screws A from the hardware kit Do not2. over tighten these pos A User Manual Part 2 Attaching the Mount to the Display IMPORTANT Use extra care during this part of the installation If possible avoid placing your display facedown as it may damage the viewing surface NOTE Your mount comes with a selection of different bolt diameters and lengths to accommodate a wide variety of display models Not all of the hardware in the kit will be used RMS MT2790 User Manual WARNINGS Make sure these instructions are read and thoroughly understood before attempting installation If you are unsure of any part of the installation process contact a professional installer for assistance The wall or mounting surface must be capable of supporting the combined weight of the mount and the display otherwise the structure must be reinforced Safety gear and proper tools must be used Failure to do so can result in property damage and or serious injury O Follow all instructions and recommendations regarding adequate ventilation and suitable locations for mounting your display Consult the owner s manual for your display for more information RMS MT2790 User Manual Part 2 Attaching the Mount to the Display continued Determine the correct bolt to use by examining the back of your display If the back of your display is flat and the mounting holes are flush with the surface you will use one the M4x12 Bolts C from the har
3. dware kit If the back of your display is curved has a protrusion or if the mounting holes are recessed you will need to use one the M4x30 Bolts D and the Spacers E Attach the mount to the back of your display using the hardware identified in Step 1 Make sure all screws are secure but do not over tighten NOTE If the holes of the mount do not line up with the holes on your display check to make sure that your display is VESA compatible This mount can only be used with displays that are VESA 75 or VESA 100 compatible RMS MT2790 User Manual HARDWARE KIT bs y A Drywall Screw x2 8 Concrete Anchor x2 pa C Maxt2 Bott x4 D M4x30 Bott x4 F 83 Allen Key oh E Spacer x4 vet aber kay TOOLS REQUIRED Q Phillips Head Screw Driver O Electric or Portable Drill Q 1 8 3 mm Drill Bit and Stud Finder for Drywall Installation Q 5 16 8 mm Masonry Bit for Concrete Installation RMS MT2790 User Manual Part 3 Final Assembly To complete the installation simply slide the mount with your display attached into the wall plate The plastic tab at the top of the wall plate will click to indicate that the mount is secure To remove the mount from the wall push in on the plastic tab and carefully slide the mount upwards and out of the wall plate For extra security and stability tighten the set screw located on the wall plate see illustration using the S3 Allen Ke
4. e level Mark the two holes for securing the mount and set the wall plate aside Drill a pilot hole at each marked location using an electric or portable drill and 1 8 3 mm bit Move the wall plate back into position and secure it using the Drywall Screws A from the hardware kit Do not over tighten these screws User Manual Swivel adjustments can be made simply by moving your display into the desired position If the swivel joint is too tight or becomes too loose it can be adjusted using the S4 Allen Key G provided in your hardware kit see illustration Thank you for purchasing a quality Rosewill Product Please register your product at www rosewill com for complete warranty information and future support for your product
5. y F provided with the hardware kit Remember to loosen the set screw before attempting to remove the mount from the wall RMS MT2790 User Manual INSTALLATION Part 1A Installing the Wall Plate Drywall IMPORTANT For safety reasons this mount must be secured to a wood stud The stud must be capable of supporting the combined weight of the mount and the display Use a high quality stud finder to locate a single stud where you want to install your mount Mark both edges of the stud to help identify the exact center see illustration 7 Left edge of stud Right edge of stud Contr stud RMS MT2790 User Manual Part 3 Final Assembly continued To use the integrated cable management feature route the cables through the hook located at the bottom of the wall plate see illustration OPERATION AND ADJUSTMENT To adjust the tilt angle or rotate your screen firmly grasp the sides of your display and carefully move it into position If you find the mount is too difficult to move or is too loose to hold your mount in position adjust the three screws located directly behind the head of the mount using the S4 Allen Key G from the hardware kit see illustration Make sure you adjust all three screws evenly RMS MT2790 User Manual Part 1A Installing the Wall Plate Drywall continued Place the wall plate over the center of the marked stud and level it using the integrated bubbl
Download Pdf Manuals
Related Search