RobinAir Transmission Fluid Exchanger 92500 User's Manual
Contents
1. cee See ihe ra ee ae OPERATING MANUAL A HAS le Z L G hy MDR Model 92500 Transmission Fluid Exchanger FROBINAIR Transmission Fluid Exchanger Unit Model 92500 SAFETY DEFINITIONS Follow all WARNING CAUTION IMPORTANT and NOTE messages in this manual These messages are defined as follows WARNING means you may risk serious personal injury or death CAUTION means you may risk personal injury and property damage or serious unit damage IMPORTANT means you may risk unit damage and NOTES provide clarity and helpful tips These safety messages cover situations ROBINAIR is aware of ROBINAIR cannot know evaluate and advise you as to all possible hazards You must make sure all conditions and procedures do not jeopardize your personal safety COPYRIGHT No part of this manual may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopy recorded or otherwise without the prior written permission of ROBINAIR DISCLAIMER All information illustrations and specifications contained in this manual are based on the latest information available at the time of publication The right is reserved to make changes at any time without obligation to notify any person or organization of such revisions or changes Further ROBINAIR shall not be liable for errors contained herein or for incidental or consequential damages including lost profits in connection with the fu2. 3 Press ENTER to confirm the engine is running The exchanger extracts one quart of diluted ATF and returns one quart of new ATF through the hose and back into the transmission fluid pan The Replace Fluid Out and New Fluid In displays respectively the amount of fluid extracted and the amount of new fluid to be added This recycling continues until the selection made in step 8 under Power Up is met i e using the 12 quart default Replace Fluid Out will be 12 and New Fluid In will be 0 2004 SPX Corporation Operating Procedures Dipstick Only Mode continued When the selection in step 8 is met the buzzer sounds and the End Service and ENTER LEDs light 4 Press ENTER to confirm that the correct amount of ATF has been replaced Check Trans Level LED lights Check the ATF Level in the Pan 1 Remove the flexible nylon hose 2 Insert the dipstick 3 Remove dipstick to check level of fluid If the fluid level needs to be adjusted continue on to Adjust the ATF Level If the level is satisfactory go to step 4 under Adjust the ATF Level Adjust the ATF Level 1 Place the flexible nylon hose in the dipstick tube 2 Press ENTER The To Trans From Trans and Finish LEDs light Transmission Fluid Exchanger a If the level is too low select To Trans LED Press ENTER Press the up arrow key to select how much fluid to add each press indicates one tenth of a quart b If the
3. Manual Top Off Drain Waste Tank Total Count Start Service LED Start Engine LED Down Light Indicators Up Se ooo Reversed Polarity Return Line Ne BOW ANTS a R ced a out Select Button Enter Button Finish LED Check Trans Level LED End Service LED a ON OFF Switch Transfer Indicators ATF In ATF Out New Fluid In Displays amount of fluid added Replaced Fluid Out Displays amount of fluid extracted UP DOWN Arrows Adjusts amount of fluid in or out Pause Abort Pauses or aborts a transfer Error Message Indicators Displays error message Mode Indicators Identifies procedures available Select Button Selects the desired mode or procedure Enter Button Accepts mode selected and starts the ATF exchange Display Screens Displays operational or error information Transfer Indicators and LEDs Indicates the transfer that is presently taking place ON OFF Power Switch Turns the unit on 2004 SPX Corporation Initial Setup Accessory Kit Unpack Accessory Kit located inside the rear door of unit Accessory Kit includes Adapter set warranty card and hose hanger bracket Attach Hose Hanger Bracket 1 Drop tube all the way down over existing tube on unit 2 Rotate to align holes 3 Insert screw into the middle hole L Hose Hanger Bracket 4 Align holes gt Nylon Hose Storage o Registering th
4. Original No Description Application 529581 6318 05 5 16 Flare 1 2 20 Assembly Domestic and Import 529582 6308 04 1 2 20 External Long End SAE 529583 6313 01 1 2 20 Internal x SAE 45 Degrees Domestic and Import 529584 6307 04 5 8 18 Internal x SAE IN Ford 529585 6318 06 3 8 Flare 5 8 18 Assembly Domestic and Import 529586 6301 01 5 8 18 Internal x SAE 45 Degrees Domestic and Import 529587 6308 14 M14 Banjo Fitting 2 fittings included in 529567 Kit saoe Import 529588 6310 16 Import 529589 6302 02 5 8 18 Internal x 45 Degrees Domestic and Import 529590 2025 13 S 25 x 1 4 NPTM Plug 2 plugs included in 529567 Kit Domestic 16 529591 2025 33 S 25 x 3 8 NPTM Plug 2004 SPX Corporation Domestic Replacement Adapters contd Order No Description Application Original No 529592 1 2 to 29 32 x 5 16 Band Clamp General 2102 07 3 clamps included in 529567 Kit 529593 M14 Banjo Bolt Long Import 6007 14 529594 M14 Cap Nut Import 1419 98 529595 M14 Copper Washer Import 1602 14 3 washers included in 529567 Kit 529596 S 25 x 3 8 NPTF Plug Domestic 2025 32 529597 1 2 x 20 Internal Inverted Domestic 6308 02 and Import 529598 1 2 x 20 Internal SAE Inverted Ford 6308 03 529599 5 8 x 18 Ford 6307 03 529600 1 2 x 2
5. level is too high select From Trans LED Press ENTER Press the up arrow key to select how much fluid to take out each press indicates one tenth of a quart 3 When transfer is complete go to Check the ATF Level in the Pan 4 If the level is satisfactory press SELECT until Finish LED lights a Wait for one second b Press ENTER to confirm the function c Press ENTER again The display reads SR FIN indicating the service is finished Operating Procedures Dipstick Cooler Mode Initially transfers used ATF and new ATF through the transmission s dipstick tube Then with the engine running new ATF is pumped into the transmission through the dipstick tube while the old ATF is evacuated through the cooler lines This mode provides the quickest transfer of used and new ATF Note Confirm vehicle and transmission are at operating temperature before initiating service Identify Cooler Lines 1 Disconnect cooler lines and attach adapters to the input and output connectors These adapters may be open hoses and or snap or threaded fittings Note To minimize the total time of the ATF service this step may be performed during the static engine not running phase when the used ATF in the transmission pan is being exchanged with the new ATF Power Up 1 Connect the power cord to a 12V DC battery red to the positive post and black to the negative post 2 Turn the unit on The Reversed Polarity LE
6. pan 1 Press SELECT until the To Trans LED is lit 12 2 Press ENTER The amount removed will display on the Replaced Fluid Out display 3 Adjust the New Fluid In display to match the Replaced Fluid Out display 4 Press ENTER Drain Waste Tank Transfer used ATF from the internal waste tank to an external waste ATF reservoir Power Up 1 Connect the power cord to a 12V DC battery red to the positive post and black to the negative post 2 Ensure the units hoses are disconnected from the vehicle 3 Turn the unit on The Reversed Polarity LED lights if the power is connected incorrectly The unit self tests The buzzer sounds all LEDS and displays light and flash the flexible nylon hose evacuates ATF and the software version displays 4 Disconnect the red hose from the wand assembly Connect the drain waste adapter 546763 to the red hose and place into an external waste ATF reservoir Start Service 1 Press the SELECT button until only the Drain Waste Tank LED is lit and flashing 2 Pause until the ENTER LED lights and flashes about one second 3 Press ENTER to confirm the selection The display reads DRN XXX which is the amount left to be drained When the waste tank is drained the display reads SR FIN indicating service is finished 2004 SPX Corporation Operating Procedures Total Count Displays the number of ATF exchanges performed Power Up 1 Connect the power
7. 0 External x 45 Degrees Domestic 6313 02 and Import 529601 S 25 x 1 4 NPTF Plug Domestic 2025 12 529734 75 x 5 16 OD Dipstick Tube Adapter Assembly 6300 00 75 with compression fitting connection 547222 75 x 5 16 OD Dipstick Tube Adapter Assembly 6300 00 75 with push to connect fitting connection 529740 42 x 1 4 OD Dipstick Tube Adapter 6300 00 42 With compression fitting connection 547223 42 x 1 4 OD Dipstick Tube Adapter 6300 00 42 with push to connect fitting connection 17 Transmission Fluid Exchanger Replacement Adapters contd Order No Original No Description Application 546763 2030 31 S 48 x 9 Hose Drain Hose Assy Drain Waste Tank 546764 6306 08 1 2 Female Snap Lock Domestic 546765 6319 06 3 8 Male Snap Lock 18 546766 6304 12 1 2 Push on Barb 2004 SPX Corporation Replacement Parts Illustration Part Number Description 92501 Pump Assembly Replacement 92501RBK Pump Head 90516 New Oil Reservoir Cap 92509 Quick Disconnect Coupler S 25 x 1 4 Internal NPT A in illustration 2 Required 92510 Directional Valve Assembly Entire assembly shown at left 92511 Quick Disconnect Plug S 48 x 1 4 External NPT B in illustration 92513 Pressure Hose Red 92 x 3 8 Barb Assembly 92514 Recovery Hose Black 92 x 3 8 Barb Assembly 92515 Cooler Hose Black
8. 1 412 690 2001 Customer Service 1 800 533 6127 Fax 1 800 322 2890 Web Site www robinair com 526233 Rev C December 20 2007 92500 Transmission Fluid Exchanger 2004 SPX Corporation
9. 92 x 3 8 Barb Assembly 92516 Power Cord Assembly 92517 Quick Disconnect Coupler S 48 x 3 8 External NPT A in illustration 92518 Quick Disconnect Plug S 48 x 3 8 External NPT D in illustration 92521 Replacement Wand Assembly Entire assembly shown at left 19 Transmission Fluid Exchanger Limited Warranty Robinair Limited Warranty Statement Rev November 1 2005 This product is warranted to be free from defects in workmanship materials and components for a period of one year from date of purchase All parts and labor required to repair defective products covered under the warranty will be at no charge The following restrictions apply 1 The limited warranty applies to the original purchaser only 2 The warranty applies to the product in normal usage situations only as described in the Operating Manual The product must be serviced and maintained as specified 3 If the product fails it will be repaired or replaced at the option of the manufacturer 4 Transportation charges for warranty service will be reimbursed by the factory upon verification of the warranty claim and submission of a freight bill for normal ground service Approval from the manufacturer must be obtained prior to shipping to an authorized service center 5 Warranty service claims are subject to authorized inspection for product defect s 6 The manufacturer shall not be responsible for any additional costs associated with
10. D lights if the power is connected incorrectly The unit self tests The buzzer sounds all LEDS and displays light and flash the flexible nylon hose evacuates ATF and the software version displays 3 Attach the adapters to the unit s cooler line selector valve assembly Note The adapters can be connected to either coupler 4 Confirm connections are secure 5 Remove the dipstick from the transmission tube 6 Insert the unit s flexible nylon hose into the transmission dipstick tube as far as possible to reach the bottom of the transmission fluid pan The Dipstick Only Dipstick Cooler Cooler Only Manual Top Off Drain Waste Tank Total Count indicators and the SELECT button LEDs are still lit and flashing 7 Press the SELECT button until only the Dipstick Cooler LED is lit 8 Pause until the ENTER LED lights and flashes about one second 9 Press ENTER to confirm the selection The left display New Fluid In reads 12 the default quantity in quarts of new ATF to be run into the system 10 Use the arrow keys to select the amount of quarts to be transferred 12 quarts is the default minimum is 6 quarts maximum is 32 quarts 11 Press ENTER to confirm the quantity displayed The alarm sounds and the Start Service and ENTER LEDs flash Start Service 1 Press ENTER to start the ATF exchange The following takes place a The unit purges its internal fluid lines b Used ATF is then extracted f
11. O Return Line is lit No oil is returning ER FLO Supply Line is lit Check new oil reservoir Reversed Polarity is lit Check battery connections Maintenance Check the flexible nylon hose for cuts and or kinks Filter screens may need to be cleaned Locate the filter screens inside the unit clean if necessary Cabinet can be kept clean by wiping it down with a clean cloth Check wires for cuts and or damage 14 2004 SPX Corporation Replacement Adapters 529567 Complete adapters kit All replacement adapters described below are included in the kit Order No Description Application Original No 529568 1 4 M6 Barb Assembly General 6304 06 529569 5 16 M8 Barb Assembly General 6304 08 LE 529570 3 8 M10 Barb Assembly General 6304 10 p saoao 529571 1 4 M6 Open End Hose General 6303 06 529572 5 16 M8 Open End Hose General 6303 08 529573 3 8 M10 Open End Hose General 6303 10 529574 1 2 M13 Open End Hose General 6303 12 529575 5 16 x 90 Internal Domestic 6306 03 529576 3 8 External x 5 16 External Domestic 6310 10 and Import 529577 3 8 Internal Snap Lock Domestic 6306 05 Qty 2 529578 1 2 External Snap Lock Chrysler 6310 12 529579 1 2 External Angle Step GM 6312 01 529580 3 8 External Angle Step 6311 01 15 Transmission Fluid Exchanger Replacement Adapters contd Order No
12. SELECT button LEDs are still lit and flashing 5 Press the SELECT button until the Dipstick Only LED is lit 6 Pause until the ENTER LED lights and flashes about one second 7 Press ENTER to confirm the selection The left display New Fluid In reads 12 the default quantity in quarts of new ATF to be run into the system 8 Use the arrow keys to select the amount of quarts to be transferred 12 quarts is the default minimum is 6 quarts maximum is 32 quarts 9 Press ENTER to confirm the quantity displayed The alarm sounds and the Start Service and ENTER LEDs flash Start Service 1 With the vehicle engine off press ENTER to start the ATF exchange The following takes place a The unit purges its internal fluid lines b Used ATF is then extracted from the transmission pan until empty c The cumulative volume extracted appears on the Replace Fluid Out display d Through the nylon transfer hose the unit pumps back into the transmission fluid pan the same volume of new ATF that appears on the Replace Fluid Out display e The volume of new fluid yet to be pumped into the transmission pan is shown on New Fluid In display The amount designated in Power Up step 8 minus the amount transferred in Start Service step 1d f The Start Engine and ENTER LEDs flash 2 Start the vehicle s engine to circulate the new ATF through the transmission system torque converter and cooler lines
13. a product failure including but not limited to loss of work time loss of refrigerant cross contamination of refrigerant and unauthorized shipping and or labor charges 7 All warranty service claims must be made within the specified warranty period Proof of pur chase date must be supplied to the manufacturer This Limited Warranty does NOT apply if The product or product part is broken by accident The product is misused tampered with or modified 2004 SPX Corporation Transmission Fluid Exchanger Visit our web site at vey www robinair com ro or Call our Toll Free Technical Support Line at 800 822 5561 in the continental U S or Canada In all other locations contact your local distributor To help us serve you better be prepared to provide the model number serial number and date of purchase of your unit To validate your warranty complete the warranty card attached to your unit and return it within ten days from date of purchase NATIONWIDE NETWORK OF AUTHORIZED SERVICE CENTERS If your unit needs repair or replacement parts contact the service center in your area For help in locating a service center call the toll free technical support line Due to ongoing product improvements we reserve the right to change design specifications and materials without notice ROBINAIR SPX Corporation 655 Eisenhower Drive Owatonna MN 55060 0995 USA Technical Services 1 800 822 5561 Fax
14. aces the ATF taken out with selector valve assembly new ATF through the other cooler line This recycling continues until the selection in step 9 under Power Up is met When the selection is met the buzzer sounds and the End Service and ENTER LEDs light Red Hose 2 Press ENTER to confirm that the correct amount of oil has been replaced Check Trans Level LED lights Selector Valve Assembly 5 Confirm connections are secure 6 Press the SELECT button until only the Cooler Only LED is lit and flashing 7 Pause until the ENTER LED lights and flashes about one second 10 2004 SPX Corporation Operating Procedures Cooler Only Mode continued Check the ATF Level in the Pan 1 Remove the dipstick to check level of fluid in transmission fluid pan If the vehicle does not have a dipstick refer to the vehicle s service manual for the method required to check the fluid level If the fluid level needs to be adjusted continue on to Adjust the ATF Level If the level is satisfactory go to step 4 under Adjust the ATF Level Adjust the ATF Level 1 Press ENTER The To Trans From Trans and Finish LEDs light a If the level is too low select To Trans LED Press ENTER Press the up arrow key to select how much fluid to add each press indicates one tenth of a quart b If the level is too high select From Trans LED Press ENTER Press the up arrow key to select how much flu
15. cord to a 12V DC battery red to the positive post and black to the negative post 2 Turn the unit on The Reversed Polarity LED lights if the power is connected incorrectly The unit self tests The buzzer sounds all LEDS and displays light and flash the flexible nylon hose evacuates ATF and the software version displays Start Service 1 Press the SELECT button until only the Total Count LED is lit and flashing 2 Pause until the ENTER LED lights and flashes about one second 3 Press ENTER to confirm the selection The total number of services performed is displayed the Finish LED flashes 4 Press ENTER to return to mode selection after noting the total number of services Transmission Fluid Exchanger Changing Transmission Fluid Types To change transmission fluid type in a new tank fi a Connect the power cord to a 12V DC battery red to the positive post and black to the negative post Insert the flexible nylon hose into a clean ATF container Press the SELECT button until Manual Top Off LED lights Press ENTER Press the SELECT button until To Trans LED lights Press ENTER Press the UP arrow key until display reads an amount more than what is in the new tank Press ENTER The unit will pump ATF from the new tank into the clean ATF container Turn the unit off when completed The unit will clear the lines when it is restarted 13 eee Error Messages ER FL
16. ction General Description The 92500 provides an easy efficient way of replacing automatic transmission fluid in a vehicle The Exchanger removes the used transmission fluid and replaces it with new fluid which reduces the harmful contaminants and restores the fluid properties extending the life of the vehicle s transmission Glossary of Terms ATF Automatic transmission fluid oil Unit The transmission fluid exchanger Dipstick Only Mode Transfers used ATF and new ATF through the transmission s dipstick tube by running a hose directly into the transmission fluid pan This mode eliminates the need to remove the cooler lines Dipstick Cooler Mode Initially transfers used ATF and new ATF through the transmission s dipstick tube Then with the engine running new ATF is pumped into the transmission through the dipstick tube while the used ATF is evacuated through the cooler lines This mode provides the quickest transfer of used and new ATF Cooler Only Mode Transfers used ATF and new ATF through the oil cooler lines Use this mode if the transmission does not have a dipstick Manual Top Off Mode Manually adds or removes fluid to or from the transmission pan Use this mode if it is necessary to remove the transmission pan or to add fluid when using another mode Drain Waste Tank Transfers used ATF from the internal waste tank through the nylon transfer hose to an external waste ATF holding tank To
17. e Unit To validate the warranty provided by SPX ROBINAIR complete the warranty card included in the accessory kit and mail it within ten days from the date of purchase Application Notes Ford Taurus with a 3 0 liter V6 requires the removal of the vent cap located behind the shifter linkage on top of transmission before service This will minimize overfilling due to lack of headroom in the transmission housing Low pressure transmissions require the transmission be left in neutral with the parking brake secured during the dynamic engine running phase of the ATF service Import vehicles with small dipstick tube openings require the 529740 flexible nylon hose which has a smaller blue section at the end in place of the 529734 hose Helpful Tips To avoid oil spillage turn unit on before removing the flexible nylon hose from its storage area Press the Pause Abort once to pause an opera tion press ENTER to continue the operation Press and hold the Pause Abort button to discontinue an operation and to reset the unit For the quickest and most accurate exchange ensure transmission is warmed to normal operating temperatures IMPORTANT To prevent damage to the vehicle ensure all hoses are correctly connected before transferring fluid A WARNING A This manual contains important procedures concerning the setup operation and i maintenance of the unit Study and follow all warnings at the beginning
18. ick 3 Remove the dipstick to check fluid level If the fluid level needs to be adjusted continue on to Adjust the ATF Level If the level is satisfactory go to step 4 under Adjust the ATF Level Transmission Fluid Exchanger Adjust the ATF Level 1 Place the flexible nylon hose in the dipstick tube Note An alternative method is to disconnect the red hose from the dipstick wand assembly and connect it to the selector valve assembly Red Hose Selector Valve Assembly 2 Press ENTER The To Trans From Trans and Finish LEDs light a If the level is too low select To Trans LED Press ENTER Press the up arrow key to select how much fluid to add each press indicates one tenth of a quart b If the level is too high select From Trans LED Press ENTER Press the up arrow key to select how much fluid to take out each press indicates one tenth of a quart 3 When transfer is complete go to Check the ATF Level in the Pan 4 If the level is satisfactory press SELECT until Finish LED lights a Wait for one second b Press ENTER to confirm the function c Press ENTER again The display reads SR FIN indicating the service is finished Operating Procedures Cooler Only Mode Transfers used ATF and new ATF through the 8 Press ENTER to confirm the selection The cooler lines left New Fluid In display reads 12 the default quantity in quarts of new ATF to be Note Conf
19. id to take out each press indicates one tenth of a quart 2 When transfer is complete go to Check the ATF Level in the Pan 3 If the level is satisfactory press SELECT until Finish LED lights a Wait for one second b Press ENTER to confirm the function c Press ENTER again The display reads SR FIN indicating the service is finished Transmission Fluid Exchanger Manual Top Off Mode Transfers used ATF and new ATF through the transmission s dipstick tube This mode is commonly used when the transmission fluid pan needs to be removed to change gaskets or replace a filter When using another mode this mode is required to top off the ATF fluid level Note Confirm vehicle and transmission are at operating temperature before initiating service Power Up 1 Connect the power cord to a 12V DC battery red to the positive post and black to the negative post 2 Remove the dipstick from the transmission noting ATF level which will determine whether additional ATF needs to be added or withdrawn 3 Turn the unit on The Reversed Polarity LED lights if the power is connected incorrectly The unit self tests The buzzer sounds all LEDS and displays light and flash the flexible nylon hose evacuates ATF and the software version displays 4 Insert the unit s flexible nylon transfer hose into the transmission dipstick tube as far as possible to reach the bottom of the oil pan 5 Press the SELECT bu
20. irm vehicle and transmission are at run into the system operating temperature before initiating service 9 Use the arrow keys to select the amount of quarts to be transferred 12 quarts is the default minimum is 6 quarts maximum is 32 1 Disconnect cooler lines and attach adapters quarts to the input and output connectors Identify Cooler Lines 10 Press ENTER to confirm the quantity displayed The alarm sounds and the Start Power Up Engine and ENTER LEDs flash 1 Connect the power cord to a 12V DC 11 Start the vehicle s engine battery red to the positive post and black to the negative post Start Service 1 Press ENTER to start the ATF exchange The following takes place 2 Turn the unit on The Reversed Polarity LED lights if the power is connected incorrectly The unit self tests The buzzer sounds all LEDS and displays light and flash the dipstick tube holder evacuates ATF and the software version displays a The unit extracts used ATF from one of the cooler lines b The amount of ATF extracted appears on the Replaced Fluid Out display i e if 12 was selected in Power Up step 9 and 3 quarts were extracted in step 1a above Replaced Fluid Out will display 9 3 Attach the adapters to the unit s cooler line selector valve assembly Note The adapters can be connected to either coupler 4 Disconnect the red hose from the dipstick wand assembly and connect it to the c The unit repl
21. of this manual Do not operate the unit until you have read and understand the contents of this manual If you do not understand any of the contents of this manual notify your supervisor If the operator cannot read English all instructions and safety precautions must be read and discussed in the operator s native language Transmission Fluid Exchanger Operating Procedures Dipstick Only Mode The Dipstick Only mode transfers used ATF and new ATF through the transmission s dipstick tube by running a hose into the transmission fluid pan emptying it of its contents and then with engine running adding ATF ATF is then subtracted until a user specified amount of new ATF has been added Note Confirm vehicle and transmission are at operating temperature before initiating service Power Up 1 Connect the power cord to a 12V DC battery red to the positive post and black to the negative post 2 Turn the unit on The Reversed Polarity LED lights if the power is connected incorrectly The unit self tests The buzzer sounds all LEDS and displays light the flexible nylon hose evacuates ATF and the software version displays 3 Remove dipstick from the transmission tube 4 Insert the unit s flexible nylon hose into the transmission dipstick tube as far as possible to reach the bottom of the oil pan The Dipstick Only Dipstick Cooler Cooler Only Manual Top Off Drain Waste Tank and Total Count indicators and the
22. rnishing performance or use of this material If necessary obtain additional health and safety information from the appropriate government agencies and the vehicle and oil manufacturers A To prevent personal injury and or property damage Allow only gualified personnel to operate the unit Study understand and follow all instructions and warnings before operating this device The operating instructions and safety precautions must be read and discussed in the operator s native language if the operator cannot read these instructions Si el operador no puede leer o comprender estas instrucciones de funcionamiento y las precauciones de seguridad stas deber n leerse y comentarse en el idioma nativo del operador Si I utilisateur ne peut pas lire les directives relatives au fonctionnement et aux mesures de s curit celles ci doivent pouvoir tre transmises l utilisateur dans sa langue maternelle Wear protective equipment including safety goggles Disconnect hoses with extreme caution Keep tools electrical cords and hoses away from moving engine parts Vent exhaust to the outside while running the vehicle Never run a vehicle without adequate ventilation in the work area Before starting the vehicle s engine verify the vehicle is in PARK or NEUTRAL with the emergency brake ON IMPORTANT Review current local state and federal statutes cases laws and regulations to determine the current status and appropria
23. rom the transmission fluid pan until empty c The cumulative volume extracted appears on the Replace Fluid Out display d Through the flexible nylon hose the unit pumps back into the transmission fluid pan the same volume of new ATF that appears on the Replace Fluid Out display 2004 SPX Corporation Operating Procedures Dipstick Cooler Mode continued e The volume of new fluid yet to be pumped into the transmission pan is shown on New Fluid In display the amount designated in Power Up step 10 minus the amount transferred in Start Service step 1d f The Start Engine and ENTER LEDs flash 2 Start the vehicle s engine to circulate the ATF through the transmission system torque converter and cooler lines 3 Press ENTER to confirm the engine is running The unit extracts used ATF from the cooler lines and returns new ATF through the nylon transfer hose and back into the transmission fluid pan The Replace Fluid Out and New Fluid In displays respectively the amount of ATF extracted and the amount of new ATF added This recycling continues until the selection made in step 10 under Power Up is met When the preset amount is met the buzzer sounds and the End Service and ENTER LEDs light 4 Press ENTER to confirm that the correct amount of ATF has been replaced Check Trans Level LED lights Check the ATF Level in the Pan 1 Remove the flexible nylon transfer hose 2 Insert the dipst
24. tal Count Displays the number of ATF exchanges performed Pause Abort Pauses or aborts a transfer Press button once to pause Press and hold button to abort Note When abort is selected the unit resets itself All measurements will be cancelled IMPORTANT Review current local state and federal statutes cases laws and regulations to determine the current status and appropriate disposal method for the automatic transmission fluid It is the responsibility of the user to determine if a material is a hazardous waste at the time of disposal Ensure that you are in compliance with all applicable laws and regulations 2 EE gt o lt c b gt c Kg 2004 SPX Corporation Introduction Component Identification and Location 3 x Hose Hanger Unit Front View g iF Dipstick Wand Assembly Selector Valve Assembly Hose Hanger Indicator Light Nylon Hose Control Panel Shelf for tools and Built in Handle accessories apy ROBIN AIRI Polypropylene Cabinet for durability and light weight Large Wheels for ease of mobility Locking Casters Transmission Fluid Exchanger Introduction Component Identification and Location continued Control Panel ON OFF Indicator Light Transfer LEDs Pause Abort To Trans From Trans Button Arrow Buttons Mode LED Indicators Dipstick Only Dipstick Cooler Cooler Only
25. te disposal method for transmission oil It is the responsibility of the user to determine if a material is a hazardous waste at the time of disposal Ensure that you are in compliance with all applicable laws and regulations Table of Contents Safety Warnings inside front cover INTFOGUCUOM SAS ANG AA A a ea at en M nn cuts 2 General Description ess te eee eee 2 Glossary of T moin ni nn ire 2 Component Identification and Location 3 Uni Front View 4 nu AL DE do ee Aedes ade sce CC CEL 3 Control Panel eu inner een Y ne YG 4 LL LEE E LIT ER Rs 5 ACC SSON 21 Y UN dd A Rs Art da 5 Registering the Unit ie nest ene 5 Application Note HT H c acs 5 Feipiul Tips E ne RE 5 Operating Proc dures sssssssessmmsersenensertenndeseiin in sas ion 6 DIpsuck Oniy Modeic ann te nn den eluent ns Y DR I SDN 6 Dipsuc GcolenMode a ae A Ga Y ANNE Rte de 8 Cooler Only Mode scien icin i i FLYN Fd FUDD CYR OTO 10 Manual Top Off MO Ron en nn COR OA UC 11 BIT L 15 al CR dT du ad ee est 12 Total Count eie Gei ade cee ese teats Y FFR 13 Changing Transmission Fluid Types 13 Error Message nu i da NG SO annee res de 14 Maintenance ee eg i eid Sects Sad tees dd GR Y REEE GR 14 Replacenient Adapters cu neu enu nee ais ae Wie ent 15 Replacement Parts SR Wee RE RTE Ne ADO 19 Warranty Statement sine inside back cover EE 1 Transmission Fluid Exchanger Introdu
26. tton until only the Manual Top Off LED is lit and flashing 6 Pause until the ENTER LED lights and flashes about one second 7 Press ENTER to confirm the selection The Check Trans Level To Trans and From Trans LEDs light Drn Pan appears on the display 11 Operating Procedures Manual Top Off Mode continued Adjust the ATF Level 1 In step 2 under Power Up the ATF level was determined noting whether ATF needed to be added subtracted or it was satisfactory a If the level is too low select To Trans LED 1 Press Enter 2 Press the arrow key to select how much fluid to add each press indicates one tenth of a quart 3 Pause after the correct volume is selected The ENTER key lights and flashes 4 Press ENTER to start the service b If the level is too high select From Trans LED 1 Press Enter 2 Press the arrow key to select how much fluid to take out each press indicates one tenth of a quart 3 Pause after the correct volume is selected The ENTER key lights and flashes 4 Press ENTER again to start the service c If the transmission fluid pan needs to be removed press SELECT until Drn Pan appears on the display 1 Pause until ENTER LED lights about one second 2 Press ENTER to confirm the function 3 Press ENTER again to start draining the pan The unit will stop when pan is empty Refill Transmission Fluid Pan To refill the transmission fluid
Download Pdf Manuals
Related Search