Robic SC-577 User's Manual
Contents
1. segment and NO DATA will be shown 3 To exit Chronograph Recall mode press S3 will enter mode selection display J HOW TO RESET THE WATCH Press S1 S2 S3 and S4 simultaneously all segments will be off then release the buttons can reset the watch After reset test patterns will be shown for a few seconds and then the display will be as follow K BATTERY REPLACEMENT Replace the exhausted battery with a CR2032 cell or equivalent LIMITED WARRANTY OUR BASIC POLICY Marshall Browning International Corporation MBI Corp warrants to the original owner this timepiece excluding battery less band or strap for the period of one year from the original purchase date This limited warranty is given by MBI Corp and not by the dealer from whom the timepiece was purchased THE WARRANTY PROCESS WHAT IS COVERED BY THE WARRANTY If the timepiece develops a manufacturing defect within the one year limited warranty period it will be either repaired or replaced at MBI Corp s option with a timepiece of equal value providing the original owner submits the following 1 Proof of purchase i e a validated store receipt showing date of purchase 2 A check or money order no cash please in the amount of 7 50 to cover the cost of shipping and handling WHAT IS NOT COVERED BY THE WARRANTY A MBI Corp will not repair defects of damages caused by or showing evidence of 1 Improper or unauthorized service 2 Misuse2. MODE SELECTION DISPLAY SHOW TIME FOR 3 SECONDS REVERSE SELECTION OF LAP NUMBER IN SEGMENT D MODE CHANGE OPERATION At any mode except setting press S3 will enter mode selection display and a Beep sound will be given Then press the corresponding button to enter the desired mode directly ANY MODE 4 s3 MODE SELECTION DISPLAY s4 s1 TIMER MODE lt S4 S1 gt ALARM MODE M DE THR i Litas s3 s2 TIME MODE lt 3 S2 gt CHRONOGRAPH MODE A s5 CHRONOGRAPH RECALL MODE E HOW TO SET NORMAL TIME AND DUAL TIME At mode selection display press S3 to enter Normal Time mode T1 or Dual Time mode T2 mode prompt TIME will be displayed for 2 seconds first Press and hold S2 for 2 seconds to toggle Normal Time mode or Dual Time mode Press S1 to toggle between the 2 display formats of time one with enlarged hour and minute digits Press and hold S4 for 3 seconds SET HOLD displayed to enter setting mode The second digits start flashing Press S1 forward or S2 reverse to adjust the flashing digits Press and hold S1 or S2 for fast setting Press S3 to select the next digits weekday 12 24HR or M D D M for setting The sequence is shown as follow 3 3 3 3 SECOND gt HOUR gt MINUTE gt YEAR gt MONTH s3 A s3 s3 s3 Pal s3 M D D M lt 12 24HR lt WEEKDAY lt DAY When setting seconds pressing S1 or S2
3. Mm gt gt MONTH 3 3 s3 a Ti T2 lt DAY lt After all adjustments are completed press S4 to exit the setting mode Press S1 to toggle the alarm and chime function on or off CHIME ICON fnil laii in CHIME ON Remarks 1 There are 6 alarms that work independently Alarm 1 and alarm 2 are daily alarms alarm 3 and alarm 4 are weekday alarms alarm 5 and alarm 6 are date alarms If month and day of alarm 5 or alarm 6 are set to the alarm will act as daily alarm 2 The alarm sounds for 20 seconds at alarm time if the alarm function is on Press any button to stop the alarm sound If the chime function is on the chime icon will be displayed the watch will give out a Beep Beep sound at every full hour and there will be button confirmation sound The alarm function is automatically set to on when exiting setting mode The alarm icon is displayed at the time mode T1 or T2 that the alarm is set to refer to If 24 hour display format is selected for time mode there will be no AM flag A or PM flag P for alarm time If there is no button operation for about 2 minutes in setting mode the watch will return back to Alarm mode automatically If S5 is pressed in Alarm mode Time mode will be shown for 3 seconds and then return to the previous display automatically 9 To exit Alarm mode press S3 will enter mode selection display NO Of wo 00 H H
4. tampering abuse or mistreatment of the timepiece 3 Damage to the case or viable cracking of the lens 4 Moisture damage if the product is a non water resistant timepiece B If we find that the battery is the cause of the defect MBI Corp reserves the right to charge your 7 50 for a new replacement MBI Corp is not liable for incidental or consequential damages Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you YOUR RIGHTS UNDER IMPLIED WARRANTIES AND STATE LAW MBI Corp limits the duration of any warrant implied by state law including the implied warrant of merchantability to one year from the date of original purchase Some states do not allow limitations on how long an implied warranty lasts so the above limitation my not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state CARING FOR YOUR TIMEPIECE Proper care of your timepiece will provide many years of enjoyment We recommend that 1 The battery be replaced at once when it becomes depleted Please ask your local retailer to replace the battery for you using CR2032 Lithium or equivalent 2 The lens be replaced immediately if it becomes damaged as contamination from dust moisture and other foreign substances will damage the module 3 Ifthe timepiece is not marked water resistant avoid immersing or exposi
5. HOLD displayed to enter setting mode The second digits start flashing Press S1 forward or S2 reverse to adjust the flashing digits Press and hold S1 or S2 for fast setting Press S3 to select the next digits or timer number for setting The sequence is shown as follow 3 3 3 3 SECOND gt MINUTE gt HOUR gt TIMER NUMBER After all adjustments are completed press S4 to exit the setting mode Press S2 to select TMR1 to TMR5 as the beginning of the count down process Press S1 to start the timer The count down process will run through all set timers TMR1 to TMR5 in loop structure and when it pass the beginning again repetition number shown at the bottom row of the display will increase by 1 When the timer is counting press S1 can toggle between the display formats of timer PRESET TIME COUNT DOWN TIME Press S2 to stop the timer or the timer will stop automatically when repetition number reaches 30 Then press S4 to reload preset timer time or press and hold S2 for 2 seconds RST HOLD displayed to reset all timers TMR1 to TMRS to zeros In both cases repetition number is reset to zeros 2 Count down stop timer Press and hold S4 for 3 seconds SET HOLD displayed to enter setting mode The second digits start flashing Press S1 forward or S2 reverse to adjust the flashing digits Press and hold S1 or S2 for fast setting Press S3 to select the next di
6. OPERATING INSTRUCTIONS FOR Robic SC 577 Thank you for buying the Robic SC 577 300 memory personal training watch Your purchase brings you a world class watch with timekeeping functions suitable for a wide variety of activities Please read a these instructions carefully to fully acquaint yourself with the many functions offered by the SC 577 A FEATURES The SC 577 is a multi function watch providing Dual Time Timer Alarm Chronograph and Chronograph Recall The main features are listed as follows CHIME ICON ALARM ICON Direct Mode Selection 6 modes of operation Normal Time T1 Dual Time T2 Timer Alarm Chronograph and Chronograph Recall Normal Time mode presents weekday hours minutes seconds month day and T1 year can also be set Dual Time mode presents weekday hours minutes seconds month day and T2 year can also be set 2 display formats of time selectable one with enlarged hour and minute digits 12 24 hour display formats selectable Month day or day month display formats selectable Auto calendar from 1990 2049 2 Count Down Timers selectable One timer works in loop structure and the other one is a count down stop timer The timers are of 1 second resolution and with working range up to 23 hours 59 minutes 59 seconds 6 alarms that can be set to refer to T1 or T2 2 are daily alarms 2 are weekday alarms and 2 are date alarms Hourly chime signal chime on with
7. OW TO USE CHRONOGRAPH At mode selection display press S2 to enter Chronograph mode mode prompt CHRON will be displayed for 2 seconds first Lap number lap time and split time are shown at the top middle and bottom row of the display respectively Press S1 to start the chronograph For the first hour the chronograph shows minutes seconds and 1 100 seconds then the chronograph shows hours minutes and seconds Press S1 again to take lap and split times Lap number lap time and split time will be shown for 5 seconds and then the display will show current lap number and running times of chronograph Press S1 to take the next lap and split times Press S2 to stop the chronograph at this stage press S2 will show FREE lap number Then press S1 to re start the chronograph or press and hold S4 for 3 seconds RST HOLD displayed to end and store the segment The chronograph will be reset back to all zeros and L001 is shown at the top row and the chronograph is now ready for next segment Remarks 1 The chronograph is of 1 100 second resolution for the first hour and 1 second resolution for the rest and with working range up to 24 hours then the chronograph stop automatically 2 There are 300 lap memories that can be stored in a maximum Beyond these limits FULL will be displayed at the top row and further data will not be stored 3 Each segment can store the segment number month day w
8. button confirmation sound 1 100 second chronograph with working range up to 24 hours Both Lap and Split time can be taken 300 lap memories that can be stored in a maximum for recall Each segment stores the segment number month day weekday and lap data for recall 3 seconds light up EL back light B EL BACK LIGHT Press S4 for EL back light with 3 seconds auto light up C BASIC OPERATION OF BUTTONS S1 ENTER ALARM MODE MODE SELECTION DISPLAY TOGGLE DISPLAY FORMATS OF TIME START TIMER TOGGLE DISPLAY FORMATS OF TIMER TIMER COUNTING TOGGLE ALARM AND CHIME ON OR OFF START LAP OF CHRONOGRAPH FORWARD SELECTION OF LAP NUMBER IN SEGMENT FORWARD SETTING SET S2 ENTER CHRONOGRAPH MODE MODE SELECTION DISPLAY VIEW NORMAL TIME OR DUAL TIME TOGGLE NORMAL TIME OR DUAL TIME PRESS AND HOLD SELECT TIMER TIMER RESET OR RELOADED STOP TIMER RESET TIMER PRESS AND HOLD WHEN TIMER IS STOPPED SELECT ALARM NUMBER AND CHIME STOP CHRONOGRAPH SHOW FREE LAP NUMBER CHRONOGRAPH STOPPED SELECT SEGMENT REVERSE SETTING SET S3 ENTER MODE SELECTION DISPLAY ENTER TIME MODE MODE SELECTION DISPLAY SELECT SETTING SET S4 ENTER TIMER MODE MODE SELECTION DISPLAY EL BACK LIGHT SET PRESS AND HOLD RELOAD TIMER TIMER STOPPED STORE SEGMENT AND RESET CHRONOGRAPH PRESS AND HOLD CLEAR SEGMENT PRESS AND HOLD EXIT SET S5 ENTER CHRONOGRAPH RECALL MODE
9. eekday lap numbers lap times and split times for recall 4 If S5 is pressed in Chronograph mode Time mode will be shown for 3 seconds and then return to the previous display automatically 5 To exit Chronograph mode press S3 will enter mode selection display 1 HOW TO USE CHRONOGRAPH RECALL At mode selection display press S5 to enter Chronograph Recall mode mode prompt CH RC will be displayed for 2 seconds first Press S2 to select segment Weekday segment number month and day will be shown for 1 second first and then lap number lap time and split time will be shown at the top middle and bottom row of the display respectively Press S1 forward or S5 reverse to retrieve the data stored in the segment In order to clear one segment press S2 to select the segment to be cleared then press and hold S4 CLR HOLD displayed until CLR HOLD ALL are shown release S4 and the selected segment will be cleared And all segments stored beyond the cleared segment will move up by 1 In order to clear all segments stored press and hold S4 CLR HOLD displayed until CLR HOLD ALL are shown continue holding S4 for another 2 seconds and all segments stored will be cleared And the display will show NO DATA Remarks 1 Segments cannot be cleared if the chronograph is running 2 If there is only one segment stored press and hold S4 for 4 seconds CLR HOLD displayed will clear the
10. gits for setting The sequence is shown as follow 3 3 3 SECOND gt MINUTE gt HOUR After all adjustments are completed press S4 to exit setting mode Press S1 to start the timer When the timer is counting press S1 can toggle between the display formats of timer PRESET TIME COUNT DOWN TIME Press S2 to stop the timer or the timer will stop automatically when it counts down to zero Then press S4 to reload preset timer time or press and hold S2 for 2 seconds RST HOLD displayed to reset timer to zeros Remarks 1 The timers are of 1 second resolution and with working range up to 23 hours 59 minutes 59 seconds 2 Loop timer and count down stop timer cannot be used at the same time 3 Loop timer or count down stop timer function can be selected only when the timers are reloaded or reset 4 If preset timer time is less than 30 seconds the watch will give out 1 Beep when timer counts down to zero And if preset timer time is equal to or more than 30 seconds the watch will give out 10 Beep when timer counts down to zero Press any button can stop the Beep sound 5 If there is no button operation for about 2 minutes in setting mode the watch will return back to Timer mode automatically 6 If S5 is pressed in Timer mode Time mode will be shown for 3 seconds and then return to the previous display automatically 7 To exit Timer mode press S3 will enter mode select
11. ion display G HOW TO USE THE ALARM AND CHIME At mode selection display press S1 to enter Alarm mode mode prompt ALARM will be displayed for 2 Seconds first Press S2 to select AL1 to AL6 or CHIME Press and hold S4 for 3 seconds SET HOLD displayed to enter setting mode The hour digits start flashing Press S1 forward or S2 reverse to adjust the flashing digits Press and hold S1 or S2 for fast setting Press S3 to select the next digits or T1 T2 for setting When setting T1 T2 press S1 or S2 to toggle setting the alarm to refer to Normal Time mode T1 or Dual Time Mode T2 1 Alarm 1 and alarm 2 Alarm 1 and alarm 2 are daily alarms As illustrated in the diagram alarm 1 will sound at 7 30 AM of normal time T1 daily The setting sequence is shown as follow 3 3 3 HOUR gt MINUTE 1T1 T2 2 Alarm 3 and alarm 4 Alarm 3 and alarm 4 are weekc _ As illustrated in the diagram alarm 3 will sound at 7 30 AM of dual time T2 from Monday to Friday The setting sequence is shown as follow 3 3 HOUR gt MINUTE gt STARTING WEEKDAY 3 183 tame lt ENDING WEEKDAY 2 3 Alarm 5 and alarm 6 Alarm 5 and alarm 6 are date alarms As illustrated in the diagram alarm 5 will sound at 8 30 PM of normal time T1 on the 25th of December The setting sequence is shown as follow 3 3 HOUR gt MINUTE
12. ng it to water steam or other forms of moisture WHEN YOU REQUIRE SERVICE If your timepiece ever requires factory servicing you can send it directly to MBI CORP 115 HURLEY RD OXFORD CT 06478 We strongly recommend that when sending it through the mail you send the product insured return receipt requested so that if a problem in shipping arises you can trace it through the originating post office You will be billed for all services deemed out of warranty and since we reserve the right to substitute with a replacement product of equal or greater value NEVER include a personal item such as a watchband with the repair request Robic Timers amp pedometers for champions at every level
13. while the second digits count between 30 to 59 will reset the second digits to 00 and 1 will be added to the minute digits Year can be set from 1990 to 2049 When setting 12 24HR press S1 or S2 to toggle 12 hour or 24 hour display formats If 24 hour display format is selected there will be no AM flag A or PM flag P When setting M D D M press S1 or S2 to toggle month day or day month display formats After all adjustments are completed press S4 to exit the setting mode Remarks 1 Normal Time mode T1 and Dual Time mode T2 count up individually with the same second 2 When Normal Time mode T1 is displayed press and hold S2 for not exceeding 2 seconds can view the dual time without changing the mode 3 When Dual Time mode T2 is displayed press and hold S2 for not exceeding 2 seconds can view the normal time without changing the mode 4 If there is no button operation for about 2 minutes in setting mode the watch will automatically return back to Normal Time mode or Dual Time mode respectively 5 To exit Time mode press S3 will enter mode selection display F HOW TO USE THE TIMERS S4 S4 S3 S3 TMR1 OF LOOP TIMER COUNT DOWN STOP TIMER At mode selection display press S4 to enter Timer mode mode prompt TIMER will be displayed for 2 seconds first Press S2 to select TMR1 to TMR5 of Loop timer or count down stop timer 1 Loop timer Press and hold S4 for 3 seconds SET
Download Pdf Manuals
Related Search