Roberts Radio CR980 User's Manual
Contents
1. and the Function switch to On The Volume control should be adjusted as required Tune the radio to the desired programme by adjusting theTuning control To switch off the radio set the Function switch to Off If the radio does not switch off this may be caused by inadvertent operation of the Sleep function Press the Time Alarm off button once to cancel the sleep function and switch the radio off Setting the Clock When the mains plug is connected to the power supply the clock display will show 12 00 AM Midnight indicating the time requires setting Real time To set the time press the Time Alarm off button and either the Fast or Slow button simultaneously The Fast button is to advance the time display quickly use it to advance swiftly through several hours follow up by using the Slow button to set the exact time The time display will advance each time the button is depressed or automatically if it is kept depressed Release the buttons when the correct time is shown Note Ensure that the time is correctly set for either AMorPM The PM indicator must be lit for PM operation If the indicator is not lit the time displayed is AM Quick on off feature The Sleep and Time Alarm off button can be used together as a convenient way to turn the radio on and off when it is required to operate for a short period of less than one hour Alarm time To display the alarm time press the Alarm button When you release the butto2. the instrument was purchased It is likely that your Roberts dealer will be able to attend to any defect quickly and efficiently but should it be necessary the dealer will return the instrument to the company s service department for attention In the event that itis not possible to return the instrument to the Roberts dealer from whom it was purchased please contact Roberts Radio Technical Services department at the address shown below before taking further action These statements do not affect the statutory rights of a consumer ROBERTS RADIO TECHNICAL SERVICES DEPARTMENT 97 99 Worton Road Isleworth Middlesex TW7 6EG Technical Helpline 0181 758 0338 ce
3. ROBERTS Sound for Generations CR980 3 Band Dual Alarm Clock Radio am FM 88 92 96 100 104 106108 MHz L LI MW 540 600 700 900 1200 1600 kHz Ea OO A20W 160 180 20 240 260 kHz sa ol al al el al aol ROBERIS CR980 FM MW LW Clock Radio Alarm Please read this manual before use Controls AL 2 Time Alarm off Fast ce Aulo On E pa A 2 rari I C JL gt CIO Snooze Function switch Alarm switch Time Alarm off button Fast set button Slow set button Sleep button oc Aa VIN If you need any further advice please call our Technical Helpline on 0181 758 0338 Mon Fri 7 Battery compartment on rear 8 Volume control 9 Tuning control 10 Alarm button 11 Snooze button Controls 14 16 MW 540 600 700 900 1200 1600 kHz AL2 LW 160 180 200 240 260 kHz Scale 0 al al sl al sol ROBERIS CR980 FM MW LW Clock Radio Alarm 18 12 Auto dimmer 13 PM indicator 14 Alarm 1 indicator 15 Clock display 16 Alarm 2 indicator 17 Tuning scale 18 Waveband switch on end General Do not allow this unit to be exposed to water or steam Do not leave the unit where excessive heat could cause damage It is recommended that the FM band be used wherever possible as better results in terms of quality and freedom from interference will usually be obtained than on the MW and L
4. W bands Mains supply The CR980 will operate from a supply of AC 230 volts 50Hz W only For your convenience this product is supplied with a plug which is fitted with a fuse of the appropriate rating If the plug supplied is not suitable for your socket outlet it should be removed by unscrewing the plug top the terminal screws and removing the cable The correct style of plug to suit your household together with a correctly rated fuse should be fitted IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN IMPORTANT DO NOT make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol or coloured Green or Green and yellow The wires in the mains lead are coloured in accordance with the following codes BLUE NEUTRAL BROWN LIVE As these colours may not correspond with the coloured markings identi fying the terminals in your plug proceed as follows The wire coloured BLUE must be connected to the terminal marked N or coloured BLACK The wire coloured BROWN must be connected to the terminal marked L or coloured RED If you need any further advice please call our Technical Helpline on 0181 758 0338 Mon Fri Fuse This apparatus must be protected by a 3A fuse BS1362 in a 13A plug BS1363 If another type of plug is used a 5A fuse should be fitted in the plug adaptor or distribution board IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN Back up battery Slide the battery cove
5. control is set at an adequate level to wake you up If not manually switched off the radio and the alarm tone will automatically switch off after 59 minutes If you need any further advice please call our Technical Helpline on 0181 758 0338 Mon Fri If an alarm time has not been set and the Function switch is left in the Buzz or Auto position the alarm radio will operate at 12 00 midnight If you do not require the alarm function ensure that the Function switch is correctly set to the Off position The display alarm indicators will be Switched off Snooze Function Alternatively when the radio or buzzer alarms can be silenced for approximately 7 minutes by pressing theSnoozebutton after which time the alarm will switch on again This can be repeated within the 59 minute alarm on time Note If dual alarm has been chosen the second wake function will operate despite the use of the SNOOZE button Sleep Function Your CR980 digital clock radio can be set to operate the radio and switch off automatically after a preset period adjustable up to 59 minutes To set the sleep function switch the Function switch to Off Auto or Alarm depending on whether or not you require the alarm function the following day Press the Sleep button briefly and observe that the display indicates the preset time 59 minutes Hold the Sleep button depressed the clock display will then automati cally countdown from 59 minutes to one minut
6. e Release the button when the desired sleep time is displayed Set the Tuning and Volume controls as required Tocancelthe sleep function before the presettime has elapsed pressthe Time Alarm off button once The radio will switch off Auto Dimmer The Auto Dimmer located on the top left side of the LED display will automatically adjust the intensity of the clock display to suit room brightness Specifications Power Requirements Radio Mains Back up Battery Waveband coverage FM LW MW 88 108 MHz 150 260 kHz 540 1600 kHz AC 230 volts 50Hz W only IEC size 6LR61 PP3 Clock Imported by ROBERTS RADIO LIMITED PO BOX 130 MEXBOROUGH SOUTH YORKSHIRE S64 8YT Battery back up 12 Hr AM PM display Wake to buzzer or radio alarms 7 minute snooze function 59 minute Sleep timer The Company reserves the right to amend the specification without notice Guarantee This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown subject to the procedure stated below Should any component or part fail during this guarantee period it will be repaired or replaced free of charge The guarantee does not cover 1 Damage resulting from incorrect use 2 Consequential damage 3 Receivers with removed or defaced serial numbers Procedure Any claim under this guarantee should be made through the dealer from whom
7. n the display reverts to real time Use the Fast and Slow buttons whilst holding down the Alarm button to set the desiredAL1 or AL2time Ensure the correct AM PM setting is observed Note The alarm time can only be set with the Alarm switch in the AL1orAL2position Ifthe Alarm switch is set toAL1 2 then pressing the Alarm button will only display the real time not alarm time Alarm Function Your CR980 has both single or dual alarm functions and can be set to operate at one of two preset times or both as required For example you might want one time for during the week and another for the weekend or two different times for the same day of the week Single alarm If you require the alarm to operate once at a given time setting set the required alarm time as described above and position the Alarm switch to either AL1 or AL2 Set the Function switch to Alarm for waking to the alarm tone or Auto for waking to the radio The respective LED alarm indicator will now be lit and the alarm radio will operate at the set time You could now set the the second alarm function in the same way and simply position the Alarm switch to AL1 on weekdays and AL2 on weekends Note Once the AL1 or AL2 has operated press the Time Alarm off button once the alarm radio willsound again the next day unless the Function switch is set to Off Dual alarm If you require the alarm to operate at two different times on one day first position the Ala
8. r catch in the direction of the arrow Remove the battery cover Fit a 9 volt IEC size 6F22 6LR61 PP3 or equivalent battery into the compartment Replace the battery cover The time and alarm settings will be retained during a temporary failure ofthe AC mains supply The LED display will not be operational The battery is not necessary for the unit to function Aerials The wire aerial located on the rear of the CR980 is for FM reception The wire should be fully extended and positioned for optimum reception There is a built in ferrite aerial for MW and LW stations Rotate the CR980 to the position giving best reception Important If an alarm time has not been set and the Function switch is left in the Auto or Alarm position the alarm radio will operate at 12 00 midnight If you do not require the alarm function ensure that the Function switch is correctly set to the Off position The display alarm indicators will be Switched off Operating the Radio The radio is equipped with three wavebands to enable you to select the programme of your choice The FM waveband requires the use of an external aerial wire which can be found at the rear of the unit This should be uncoiled and positioned for the best reception The MW and LW wavebands use an internal aerial which is directional For the best reception it may be necessary to rotate the radio Connect the mains plug to a wall socket Set the Waveband switch to FM MW or LW
9. rm switch to AL1 and set the required alarm time Then move the Alarm switch to AL2 and set the second desired alarm time When both alarms have been set move the alarm switch to AL1 2 Ensure that the Function switch is in the Alarm position The display alarm indicators will both be lit and the alarms will now operate at the programmed time Once the AL1 has operated press theTime Alarm off button once The alarm radio will switch off and will operate again at a preselected AL2 time Press the Time Alarm off button again to cancel AL1 and AL2 will sound again the next day unless the function switch is set to Off Wake to alarm Once the alarm time is set move the Alarm switch to the AL1 AL2 or AL1 AL2 position Set the Function switch to Alarm TheAL10rAL2 indicator or both if dual alarm has been chosen will light and the alarm tone s will then sound at the preset time To turn off the alarm immediately either press theTime Alarm offbutton in which case the alarm will operate again 24 hours later or slide the Function switch to Off position to switch off the alarm function Note The AL1 and AL2 buzzertones are different for easy recognition Wake to radio Set the Alarm switch to the AL1 AL2 or AL1 AL2 position Set the Function switch to Auto The AL10rAL2indicator or both if dual alarm has been chosen will light and the radio will then operate at the preset time Note Ensure that the Volume
Download Pdf Manuals
Related Search