ResMed Mirage Activa LT User's Manual
Contents
1. 16 40 20 45 18 H m nw N Mask Pressure cm H O Dead Space Information The dead space of the mask varies according to cushion size It is 185 mL for the Medium size Therapy Pressure Environmental 4 to 20 cm H O Operating temperature 41 F to 104 F 5 C to 40 C Conditions Operating humidity up to 95 non condensing Storage and transport temperature 4 F to 140 F 20 C to 60 C Storage and transport humidity up to 95 non condensing Resistance Drop in pressure measured nominal at 50 L min 0 1 cm H O at 100 L min 0 7 cm H O Gross M L LW 6 06 154 mm H x 3 74 95mm W x 4 6 117 mm D dimensions Mask fully assembled no headgear The manufacturer reserves the right to change these specifications without notice Before Using the Mask A WARNINGS e The vent holes must be kept clear Follow all precautions when using supplemental oxygen e Oxygen flow must be turned off when the flow generator is not operating so that unused oxygen does not accumulate within the flow generator enclosure and create a risk of fire Ata fixed flow rate of supplemental oxygen flow the inhaled oxygen concentration varies depending on the pressure settings patient breathing pattern mask point of application and leak rate e The technical specifications of the mask are provided for your clinician to check that they are compatible with the flow2. the straps evenly The forehead support anchors your mask and should sit firmly on your forehead With the air turned off adjust the straps so that you can insert two fingers between your cheek and the lower headgear strap Check that the cushion clip is correctly inserted into the cushion and that the cushion is correctly clipped to the frame Check the the ports cap and elbow are correctly inserted Clean vents according to instructions in Cleaning the Mask at Home Reposition the mask upon the face Wind the dial in Wind the dial out Talk to your clinician Reassemble the mask according to the instructions in Reassembly Clean cushion according to instructions in Cleaning the Mask at Home Cannot insert forehead support into mask frame When assembling the mask you have inserted the dial into the frame before the forehead support Push dial base onto a hard surface until the dial comes out of the frame Disposal The mask does not contain any hazardous substances and may be disposed of with your normal household refuse English Technical Specifications The mask system does not contain latex PVC or DEHP materials Pressure Flow Curve The mask contains passive venting to protect against rebreathing As a result of manufacturing variations the vent flow rate may vary 5o Pressure Flow _ cm H O L min 5 4 19 8 28 c 8 12 34
3. 0124 10 Mask frame Mask cushion 60180 Land Clip 60177 M 60178 L 60179 LW Cushion clip 60176 Elbow 16387 Headgear clip 16569 2 16570 2 16734 10 16571 10 Swivel 16565 Headgear Upper straps 16118 S 2 PP P 60114 St 16119 L CL Lower straps S Small St Standard Fitting HIH l English Cleaning the Mask at Home e The mask and headgear should be cleaned by handwashing e The headgear may be washed without removing the headgear clips A WARNING Do not use aromatic based solutions or scented oils eg eucalyptus or essential oils bleach alcohol or products that smell strongly eg citrus to clean any of the mask components Residual vapors from these solutions can be inhaled if not rinsed thoroughly They may also damage the mask causing cracks A CAUTION If any visible deterioration of a mask component is apparent cracking crazing tears etc the mask component should be discarded and replaced e Avoid connecting flexible PVC products eg PVC tubing directly to any part of this mask Flexible PVC contains elements that can be detrimental to the materials of the mask and may cause the components to crack or break Daily After Each Use To optimize the mask seal facial oils should be removed from the cushion afte
4. 35 Others pending Mirage and Activa are trademarks of ResMed Ltd and are registered in U S Patent and Trademark Office 2008 ResMed Ltd 608232 ENG 2 o8 o9 MIRAGE ACTIVA LT USER AMER MULTI 6 08 2 3 2 Global leaders in sleep and respiratory medicine www resmed com
5. RESMED Mirage Activa LT NASAL MASK User Guide English e Francais e Espa ol e Portugu s RESMED Mirage Activa LT Rx Only NASAL MASK Thank you for choosing the Mirage Activa LT Intended Use The Mirage Activa LT channels airflow noninvasively to a patient from a positive airway pressure device such as a continuous positive airway pressure CPAP or bilevel system The Mirage Activa LT is to be used by adult patients gt 66 Ib 30 kg for whom positive airway pressure has been prescribed e intended for single patient re use in the home and multipatient re use in the hospital institutional environment Device Setting Select Activa if available or Standard as the mask option when using the Mirage Activa LT with ResMed devices that have mask setting options For a full list of compatible devices for this mask see the Mask Device Compatibility List on www resmed com on the Products page under Service amp Support If you do not have internet access please contact your ResMed representative English Parts of the Mask amp Ordering Information Complete System Frame System No headgear Medium M 60148 Medium M 60172 Large L 60149 Large L 60173 Large Wide LW 60150 Large Wide LW 60174 Frame assembly no headgear no cushion 60175 Elbow assembly elbow swivel 16399 Forehead support Forehead support pad 60123 1 6
6. generator If used outside specification or if used with incompatible devices the seal and comfort of the mask may not be effective optimum therapy may not be achieved and leak or variation in the rate of leak may affect the flow generator function e Discontinue using the mask if you have ANY adverse reaction to the use of the mask and consult your physician or sleep therapist e Using a mask may cause tooth gum or jaw soreness or aggravate an existing dental condition If symptoms occur consult your physician or dentist e As with all masks some rebreathing may occur at low CPAP pressures e Refer to your flow generator manual for details on settings and operational information e Remove all packaging before using the mask Symbols AN Caution consult accompanying documents ter Lot number REF Part number 4 Temperature limitation B Humidity limitation Does not contain latex adl Manufacturer Indicates a Warning or Caution and alerts you to a possible injury or explains special measures for the safe and effective use of the device Limited Warranty ResMed warrants that your ResMed mask system including its components mask frame cushion headgear tubing and other accessories Product shall be free from defects in material and workmanship for a period of ninety 90 days from the date of purchase by the initial consumer For further details refer to the Warranty English ResMed L
7. r use Handwash the mask by gently rubbing in warm 86 F 30 C water using mild Soap If the vent requires cleaning use a soft bristle brush Rinse all components well with drinking quality water and allow them to air dry out of direct sunlight Do not soak the mask Weekly Handwash the headgear in warm 86 F 30 C water using mild soap Reprocessing the Mask between Patients This mask should be reprocessed when used between patients Cleaning disinfection and sterilization instructions are available from the ResMed website www resmed com masks sterilization americas If you do not have Internet access please contact your ResMed representative Storage Ensure that the mask is thoroughly clean and dry before storing it for any length of time Store the mask in a cool dry place out of direct sunlight English Reassembly Troubleshooting Possible reason Mask is uncomfortable Headgear straps are too tight Cushion incorrectly inflated Mask is too noisy Cushion clip is not inserted correctly Ports cap or elbow incorrectly inserted Vents are blocked or partially blocked Air leaking around the face Mask not positioned correctly Air leaking around the bridge of the nose Air leaking around the top of the lip The mask does not fit properly Cushion could be the wrong size Mask is incorrectly assembled Cushion may be dirty Solution Adjust
8. td Manufacturer 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia ResMed Corp US Designated Agent 14040 Danielson Street Poway CA 92064 6857 USA ResMed UK Ltd EU Authorised Representative 96 Milton Park Abingdon Oxfordshire OX14 4RY UK ResMed Offices Australia Austria Belgium Brazil China Finland France Germany Greece Hong Kong India Ireland Italy Japan Malaysia Mexico Netherlands New Zealand Norway Portugal Singapore South Africa Spain Sweden Switzerland UK USA see www resmed com for contact details Mirage Activa LT Nasal Mask Protected by patents AU 2001267133 AU 710733 AU 741003 AU 766623 AU 775051 AU 777033 AU 785376 CA 2261790 DE 20122844 0 EP 0956069 EP 1187647 EP 1187649 EP 1187650 EP 1314445 EP 1334742 EP 1479406 EP 1582230 EP 1640034 HK 1057714 HK 1071083 JP 3686609 JP 3802872 JP 4031422 NZ 513052 NZ 526165 NZ 526166 NZ 526167 NZ 526168 NZ 542849 NZ 543939 US 6112746 US 6119693 US 6357441 US 6374826 US 6439230 US 6463931 US 6532961 US 6557556 US 6581594 US 6581602 US 6634358 US 6691708 US 6772760 US 6823865 US 6823869 US 6860269 US 6871649 US 6986352 US 6997188 US 7107989 US 7159587 US 7178527 US 7216647 US 7234466 US 7243651 US 7318438 Other patents pending Protected by design registrations AU 156663 FR 031430 JP 1192859 US D487510 US D493521 AU 156665 DE 40301991 5 FR 031425 JP 1197930 US D486227 US D493522 US D545960 US D5679
Download Pdf Manuals
Related Search