Renesas H8S/2168 User's Manual
Contents
1. 8 3 0 91 0 9 l pd AT o P lo oj 9 wt Oo x lt x Oo E o 2 o o co x Sl as Ty o S o EER SES EER ER Unit mm Figure 7 Recommended Dimensions for Mount Pad sENESAS 2 4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 8 Unit mm Tolerance 0 5 mm Figure 8 Dimensions for User System Interface Cable Head ztENESAS 2 5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions after connecting the user system interface cable head to the user system are shown in figure 9 Cable head EE TT 1 K Unit mm OPA TALASE Tolerance 0 5 mm User system manufactured by Tokyo Eletech Corporation Figure 9 Resulting Dimensions after Connecting User System Interface Cable 14 sENESAS Section 3 Installing the MCU on the User System CAUTION Check the location of pin 1 before inserting Use a screwdriver whose head matches the screw head The tightening torque must be 0 054 Nem or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw he2. de a ae Remove the coaxial cable which has been connected to EIO board 2 from a gutter of the emulator station 6 Set the cover of the emulator station and fasten four screws sENESAS 2 2 Connecting User System Interface Cable to User System AWARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST To connect the cable head to the user system follow the instructions below 2 2 1 Installing IC Socket After checking the location of pin 1 on the IC socket fasten it to the user system before soldering CAUTION After confirming the location of pin 1 on the IC socket apply epoxy resin adhesive to the end of the four projections at the bottom of the IC socket and fasten it to the user system ztENESAS Use the guide pins provided to determine where to install the IC socket as shown in figure 4 Pin 1 4 projections to apply epoxy resin adhesive to lt lt a _ IC socket NQPACK144SE manufactured by Tokyo Eletech Corporation Bottom view of IC socket User system Figure 4 Location Setting of IC Socket 2 2 2 Soldering IC Socket After fastening s
3. D bekeer SE EG gee ee ik 9 2 2 4 Fastenmg Cable Head ie EE REKE bee b EER KERKE ep ES SR S Re SEE bee Ee EE a Ee EE Re ge ee hees 9 PP de UR ER EE OR EE OE na iiai 11 2 3 Recommended Dimensions for User System Mount Pad iese esse see se see ee Ge ee Ge ee ee 12 24 Dimensions for User System Interface Cable Head sesse see se ese se ee ee ee Ge ek Ge ee ee 13 2 5 Resulting Dimensions after Connecting User System Interface Cable eee sesse see see 14 Section 3 Installing the MCU on the User System ee se ee ee Re ee 15 Section 4 User System Interface Circuit iss esse ss SS sd Eg Se ee se KG RE EG 17 Section 5 Verifying perdi RE RE Ge sonata eases DR Oe EE 19 Section 6 INOUCE ss DE EG ee Ge ee Ee 20 ji RENESAS Section Configuration CAUTION Use an NQPACK144SE socket manufactured by Tokyo Eletech Corporation for the TFP 144 package IC socket on the user system Figure shows the configuration of the HS2168ECN61H user system interface cable for the TFP 144 package To emulator station CTS screws M3 x 6 mm for fastening the emulator station a EIO board 1 Screws M2 0 x 10 mm for fastening cable head IC socket User system Figure 1 HS2168ECN61H User System Interface Cable ztENESAS Table 1 lists the HS2168ECN61H components Please make sure you have all of these components when unpacking Table 1 HS2168ECN61H Components No Component Quan
4. ME_N GA20 i CLKRUN_N SW9to14 rT N LPCPD_N i 1 PD2 PME_N PD3 GA20 HS2168EPI61H PD4 CLKRUN_N PD5 LPCPD_N PEO to 7 PDO to 5 Figure 11 User System Interface Circuit Pin 3 side Pin 1 side Figure 12 Settings of Switch sENESAS Table 2 Settings of Switches Switch Number Pin 1 Side Pin 3 Side SWI1 Port E7 SERIRO SW2 Port E6 LCLK SW3 Port E5 LRESET_N SW4 Port E4 LFRAME_N SW5 Port E3 LAD3 SW6 Port E2 LAD2 SW7 Port E1 LAD1 SW8 Port EO LADO SW9 Port D5 LPCPD N SW10 Port D4 CLKRUN_N SW11 Port D3 GA20 SW12 Port D2 PME_N SW13 Port D1 LSMI_N SW14 Port DO LSCI 18 sENESAS Section 5 Verifying Operation 1 When using the E6000 emulator for the H8S 2168 group turn on the emulator according to the procedures described in the H8S 2168 Group E6000 Emulator User s Manual HS2168EPI61HE 2 Verify the user system interface cable connections by accessing the external memory and ports to check the bus states of the pins with the MEMORY_FILL command emulator command If an error is detected recheck the soldered IC socket and the location of pin 1 3 The emulator connected to this user system interface cable supports two kinds of clock sources as the MCU clock an emulator internal clock and an external clock on the user system For details refer to the emulator user s manual HS2168EPI61HE To use the emulator internal clock Select the clock in the e
5. ad may break or an IC socket contact error may be caused by a crack in the IC socket solder If the MCU does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary Check the location of pin before inserting the MCU into the IC socket on the user system as shown in figure 10 After inserting the MCU fasten the socket cover with the provided four screws M2 0 x 6 mm Take special care such as manually securing the IC socket soldered area to prevent the IC socket from being damaged by overtightening the screws or twisting the components sENESAS Screws M2 0 x 6 mm lt g Socket cover MCU Pin 1 IC socket NQPACK144SE manufactured by Tokyo Eletech Corporation User system Figure 10 Installing MCU to User System sENESAS Section 4 User System Interface Circuit The microcomputer H8S 2168 is installed in this user system interface cable for emulating the LPC function An interface circuit as shown in figure 11 is provided for the user system interface signal of the H8S 2168 Figure 12 and table 2 show the settings of switches H8S 2168 1 PEO LADO pe PE1 LAD1 LADO LAD1 N6 PE2 LAD2 LAD2 LADS 330 Q 47 kQ PE3 LAD3 1 I 1 LERAME N SW1 to 8 PE4 LFRAME_N LRESET N 9 PES LRESET_N 1 1 1 1 I LCLK SERIRQ i PE SERIRG LSCI LSMI_N i P
6. as com When using any or all of the information contained in these materials including product data diagrams charts programs and algorithms please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products Renesas Technology Corporation assumes no responsibility for any damage liability or other loss resulting from the information contained herein Renesas Technology Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake Please contact Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor when considering the use of a product contained herein for any specific purposes such as apparatus or systems for transportation vehicular medical aerospace nuclear or undersea repeater use The prior written approval of Renesas Technology Corporation is necessary to reprint or reproduce in whole or in part these materials If these products or technologies are subject to the Japanese export control restrictions they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination Any diversion or reexport contrary to the export control laws and regulations of Japan and or the country of destination is prohibited Please contact Renesas Technolo
7. ation O O ye Cable head is parallel H I to emulator station e to user system User system Figure 14 User System Interface Cable Location Example 5 The P1 short connector is for testing Do not remove the jumper pin inserted in the side of pin 1 and pin 2 Figure 15 P1 Short Connector 20 sENESAS 6 To prevent EMI noise enclose the user system interface cable head in a case The recommended material of the case is iron plated with nickel or resin plated with nickel inside The case must be large enough to include the user system interface cable head user system interface cable and target system 21 7tENESAS Cautions Keep safety first in your circuit designs 1 Renesas Technology Corporation puts the maximum effort into making semiconductor products better and more reliable but there is always the possibility that trouble may occur with them Trouble with semiconductors may lead to personal injury fire or property damage Remember to give due consideration to safety when making your circuit designs with appropriate measures such as i placement of substitutive auxiliary circuits ii use of nonflammable material or ii prevention against any malfunction or mishap Notes regarding these materials l These materials are intended as a reference to assist our customers in the se
8. e cable or connectors Otherwise the connectors will be damaged ztENESAS 2 1 1 Connecting User System Interface Cable to Cable Body Connector After making sure the direction of the cable body connector is correct firmly insert the cable body connector into the emulator station socket and fasten the emulator station with two CTS screws M3 x 6 mm figure 2 Emulator station Figure 2 Connecting User System Interface Cable to Emulator Station 1 sENESAS 2 1 2 Connecting EIO Board 2 to Emulator Remove four screws at the side of the emulator station Pull up and remove the cover of the emulator casing Insert connector P5 of EIO board 2 into connector P5 in the emulator station Fasten EIO board 2 with the provided two screws M2 6 x 6 mm RED EE Set up the coaxial cable which has been connected to EIO board 2 into a gutter of the emulator station 6 Set the cover of the emulator station and fasten four screws p p A 7 7 Va ED EIO board 2 connector P5 of ElO board 2 connector P5 of emulator station Figure 3 Connecting User System Interface Cable to Emulator Station 2 7tENESAS 2 1 3 Removing EIO Board 2 from Emulator Remove four screws from the side of the emulator station Pull up and remove the cover of the emulator casing Remove two screws M2 6 x 6 mm from EIO board 2 Remove EIO board 2 from connector P5 of the emulator station
9. gy Corporation for further details on these materials or the products contained therein H8S 2168 Group TFP 144 User System Interface Cable for E6000 Emulator User s Manual Publication Date Rev 1 00 August 25 2003 Rev 2 00 December 25 2003 Published by Sales Strategic Planning Div Renesas Technology Corp Edited by Technical Documentation amp Information Department Renesas Kodaira Semiconductor Co Ltd 2003 Renesas Technology Corp All rights reserved Printed in Japan H8S 2168 Group TFP 144 User System Interface Cable for E6000 Emulator User s Manual sTENESAS RenesasTechnology Corp 2 6 2 Ote machi Chiyoda ku Tokyo 100 0004 Japan REJ11JXXXX XXXXX
10. l care such as manually securing the IC socket soldered area to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components Screws M2 0 x 10 mm Pin 1 Cable head IC socket NQPACK144SE manufactured by Tokyo Eletech Corporation Pin 1 User system Figure 5 Connecting User System Interface Cable to User System sENESAS 2 2 5 Fastening Cable Body Connect the cable body and EIO board 1 to the cable head Removing Cable body Push the lower part of EIO board 1 with your fingers EIO board 1 Cable body EIO board 1 NA o 7 I Vv N Remove jig Cable head User system Figure 6 Fastening Cable Body and EIO Board 1 When removing the cable body or EIO board 1 push the unfastening jigs If the lower part of the cable body is pushed EIO board 1 may be removed Push the lower part of EIO board 1 with your fingers sENESAS 2 3 Recommended Dimensions for User System Mount Pad Figure 7 shows the recommended dimensions for the mount pad footprint for the user system with an IC socket for a TFP 144 package NQPACK144SE manufactured by Tokyo Eletech Corporation Note that the dimensions in figure 7 are somewhat different from those of the actual chip s mount pad 0 40 X 35 14 00 0 05 gt ad pe 4 0 40 0 05 0 2 0 05 gt lt
11. lection of the Renesas Technology Corporation product best suited to the customer s application they do not convey any license under any intellectual property rights or any other rights belonging to Renesas Technology Corporation or a third party Renesas Technology Corporation assumes no responsibility for any damage or infringement of any third party s rights originating in the use of any product data diagrams charts programs algorithms or circuit application examples contained in these materials All information contained in these materials including product data diagrams charts programs and algorithms represents information on products at the time of publication of these materials and are subject to change by Renesas Technology Corporation without notice due to product improvements or other reasons Itis therefore recommended that customers contact Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor for the latest product information before purchasing a product listed herein The information described here may contain technical inaccuracies or typographical errors Renesas Technology Corporation assumes no responsibility for any damage liability or other loss rising from these inaccuracies or errors Please also pay attention to information published by Renesas Technology Corporation by various means including the Renesas Technology Corporation Semiconductor home page http www renes
12. mulator station as the system clock 6 by using the CLOCK command emulator command To use the external clock on the user system Select the target clock by using the CLOCK command emulator command and supply the external clock from the user system to the emulator When a crystal oscillator to the EXTAL and XTAL terminals for the system clock d the crystal oscillator will oscillate in the circuit as shown in figure 13 External clock must be input from the EXTAL terminal The clock input conditions are same as those for the H8S 2168 group in the hardware manual R11 MQ HCU04 To E6000 emulator EXTAL XTAL Figure 13 Oscillator Circuit sENESAS Section 6 Notice 1 Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket 2 The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU 3 To avoid breaking wires in the cable body do not place heavy or sharp metal objects on the user system interface cable 4 While the emulator station is connected to the user system with the user system interface cable force must not be applied to the cable head Position the emulator station user system interface cable and user system as shown in figure 14 Place components so that the cable body i Cable and cable head are parallel to the user system Emulator st
13. older the IC socket for a TFP 144 package to the user system CAUTION Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets Use slightly more solder than the MCU sENESAS 2 2 3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting Align pin 1 on the IC socket for a TFP 144 package on the user system with pin 1 on the user system interface cable head and insert the user system interface cable head into the IC socket on the user system as shown in figure 5 2 2 4 Fastening Cable Head CAUTION 1 Use a screwdriver whose head matches the screw head 2 The tightening torque must be 0 054 Nem or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the emulator does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary 7tENESAS Fasten the user system interface cable head to the IC socket for a TFP 144 package on the user system with the four screws M2 0 x 10 mm provided Each screw should be tightened a little at a time alternating between screws on opposing corners Take specia
14. sTENESAS H8S 2168 Group TFP 144 User System Interface Cable for E6000 Emulator HS2168ECN61H Users Manual Renesas Microcomputer Development Environment System H8S Family H8S 2100 Series Rev 2 00 Renesas Technology 2003 12 25 www renesas com Preface Thank you for purchasing this user system interface cable HS2168ECN61H for the Renesas original microcomputer H8S 2168 group The HS2168ECN61H is a user system interface cable that connects an H8S 2168 group E6000 emulator HS2168EPI61H hereinafter referred to as the emulator to the IC socket for a TFP 144 package on the user system RENESAS Contents Section l COMO UCAL OM seke nie ee ie ee ae nd be be ed se reada ie Age insidiis resis 1 Section 2 Connection Procedures siese ede bee Eed eend Goede Ge ke 3 2 1 Connecting User System Interface Cable to Emulator Station e sesse sesse see se see se ee Ge 3 2 1 1 Connecting User System Interface Cable to Cable Body Connector 4 2 1 2 Connecting EIO Board 2 to Emulator sees sees sees se ee se ee ee ee Se ee ee ee ee ke ee 5 2 1 3 Removing EIO Board 2 from EmulatOT iese sesse sesse see se ee Gee Re ek ee RA Ge ee Gee ee 6 2 2 Connecting User System Interface Cable to User SYSTEM sees see se eke ee Ge Re Ge ee ee 7 22 1 Instalime IC So ket ES ee Se ESE De AE nil Bek ESE EDE be ee Es Dek Gees 7 2 2 2 SOldering oe SEE EE AN 8 2 2 3 Inserting Cable Head iis iS N EE Ve See E Se Gee ss se GE
15. tity Remarks 1 Cable body 1 Includes coaxial cable and two EIO boards 2 Cable head 1 3 IC socket 1 For the TFP 144 package 4 Socket cover 1 For installing a TFP 144 packaged MCU 5 Screws M2 6 x 6 mm 2 For fastening ElO board 2 6 Screws M2 0 x 10 mm 4 For fastening cable head 7 Screws M2 0 x 6 mm 4 For installing a TFP 144 packaged MCU 8 CTS screws M3x6mm 2 For fastening the emulator station 9 Guide pins 1 mm 3 For determining the IC socket location 10 Screwdriver 1 For tightening screws 11 Documentation 1 User s manual for HS2168ECN61H this manual 2 sENESAS Section 2 Connection Procedures 2 1 Connecting User System Interface Cable to Emulator Station A WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned The user system interface cable dedicated to the emulator must be used Make sure the user system and the emulator station are turned off CAUTION When connecting or removing the user system interface cable apply force only in the direction suitable for connection or removal while making sure not to bend or twist th
Download Pdf Manuals
Related Search