Renesas H8/38099 User's Manual
Contents
1. gt 11 Configure Auto Update to finish the installation oS os a o X 2 Connection 12 Now connect the E8a to E8 connector on the board using the ribbon cable also connect the LCD module to LCD connector on the board ensuring that the pin 1 designation corresponds to the marking on the board 13 Connect the E8a emulator to a spare USB port The Found New Hardware Wizard will appear Please follow the steps below to install the drivers Note that administrator privileges are required for a Windows 2000 XP machine 14 Select No not this time if dialog appears and click lt Next gt 15 Verify the Recommended option is selected and click lt Next gt 16 If using Windows XP skip to step 18 otherwise click lt Next gt 17 Click lt Next gt to install the driver 18 Click lt Finish gt to close the wizard Note The Windows driver signing dialog may be displayed Please accept the driver to continue 3 High performance Embedded Workshop Workspace High performance Embedded Workshop integrates various tools such as compiler assembler debugger and editor into a common graphical user interface To learn more on how to use High performance Embedded Workshop open the High performance Embedded Workshop manual installed on your computer Start Menu gt All Programs gt Renesas gt High performance Embedded Workshop gt Manual Navigator 19 Launch High performance Embedded Workshop from2. 8099 then click lt OK gt System Clock Please input system Clack i 0 00 MMH cancel 40 Enter the ID Code OE8A for the RSKH838099 then click lt OK gt Flease input l0 Code DEBA cancel The connection to the Renesas Starter Kit will be completed and will activate the debugger buttons on the High performance Embedded Workshop toolbar 41 Right click on the download module listed in the left hand pane and select Download Dependencie estat The code will be downloaded to the microcontroller This ieee Download Debug Data Only may take several seconds Download 4 New Module Remove Debug Settings nnected 42 Click the lt Reset Go gt button 4 The code will run and you will see the LEDs flash on the board 43 Click the lt Stop gt button amp The code will stop and the source code will be opened at the current program counter 5 Next Step After you have completed this quick start procedure please review the tutorial code and sample code that came with the kit You can add projects to the current workspace by selecting Project gt Insert Project from the main menu The tutorials will help you understand the device and development process using Renesas Development Tools The Hardware manual supplied with this kit is current at the time of publication Please check for any updates to the device manual from the Renesas website at www renesas com renesas _starte
3. Everywhere you imagine E g E NI ESAS Renesas Starter Kit Quick Start ior ns 38099 LCD module E8a header Application Board Interface Reset switch AUT LCD module connector E8a emulator Analog adjust _ User LEDs Application Board Interface User switches D007574_11_S01_V01 1 Installation Do not connect the E8a emulator hardware until the software support has been installed 1 Insert the CD into your computer s CD ROM drive The CD should automatically run the installation program If the installer does not start browse to the CD root folder and double click on setup exe The installer will ask you which language is to be used please choose the appropriate one On the first screen of the installer proper click lt Next gt The License Agreement will be shown click lt Yes gt The next screen asks you to pick the world region please select and click lt Next gt Select the Renesas Starter Kit you wish to install and click lt Next gt The destination folders are specified on the next screens It is recommended to accept the default settings Click lt Next gt to continue Click lt Next gt on all screens until the installation process commences 9 After the installation the machine s site code will be shown this is not important at this stage click lt Next gt then lt Finish gt 10 Ensure Launch AutoUpdate is selected and click lt Finish
4. p down list on the toolbar is Debug Session Tiny SLP_ES selected Click the lt Connect gt button on the debug toolbar Xs The Emulator Setting dialog will be shown Select the correct device type e g H8 38099F for RSKH838099 Emulator mode Select Erase Flash and Connect If the E8a is to provide power to the CPU board select Power Target from Emulator and choose the Device H8 28099F 5 0V option Emulator Setting Mode Erase Flash and Connect Otherwise connect a 5V center positive supply C Keep Flash and Connect C Program Flash Click lt OK gt gram L Fower Supply i Power Target from Emulator M t 300m ew Cancel Do not show this dialog box again The first time the E8a is used a warning message box Please choose driver will be shown Click lt Ok gt Otherwise skip to step 38 Driver Details The Driver Details dialog will be shown Select 7 Renesas Communications Renesas Communications er After a short delay while the hardware is interrogated Interface lUsBinterace OO g select USB Interface The channel number will vary Channel Esa 7DMO00007 X Click lt Close gt ea Close Accept any dialog warning that an older version of E8a firmware is necessary to work with the application Allow download of firmware to complete this may take several seconds 39 Enter the clock speed 10 00MHz for the RSKH83
5. r kits 6 Renesas H8 Compiler The version of the compiler provided with this Renesas Starter Kit is fully functional but time limited You have 60 days to evaluate the full product before the compiler will limit the code linker to 64k bytes Full licensed H8 compiler versions are available from your Renesas supplier 7 Support Online technical support and information is available at www renesas com renesas starter kits Technical Contact Details America techsupport rta renesas com Europe tools support eu renesas com Japan csc renesas com Note on Autoupdate The Autoupdater is configured to automatically add itself to the Startup folder in the Windows Start Menu and use the registry defaults for access to the web After restarting the machine the Icon will appear in the System Tray next to the clock To change the settings or access Autoupdate simply right click on the icon and use the menu that appears Renesas Solutions Corporation 2007 Renesas Technology Europe Ltd 2007 Renesas Technology Corporation 2007 D007574_11_S01_VO01
6. the Start Menu Start Menu gt All Programs gt Renesas gt High performance Embedded Workshop gt High performance Embedded Workshop 20 In the Welcome dialog box Verify Create New Workspace is selected Click lt OK gt 21 In the New Project Workspace dialog box Set the CPU Family to H8S H8 300 and verify the Tool chain is set to Hitachi H8S H8 300 Standard Select RSKH838099 from the left hand pane 22 Enter a name for the workspace The project name will be automatically completed with the Workspace name You can change this name to Tutorial if required Click lt OK gt 23 On the RSKH838099 Step 1 window Select Tutorial and click lt Next gt 24 On the RSKH838099 Step 2 window Click lt Finish gt 25 On the Project Generator Information window Click lt OK gt The project that is created has two configurations The Release configuration can be used for the final release code version The Debug configuration allows modifications to the configuration for debugging 26 27 Select the Debug build configuration in the left hand drop down list on the toolbar x DefautSessior z Click on the Build icon to compile assemble and link the project 4 Programming and Debug 28 29 30 31 32 33 34 35 36 37 38 Ensure the SessionH8_Tiny_SLP_E8a_SYSTEM_300H a session in the right hand dro
Download Pdf Manuals
Related Search