Quantum FastStor 2 User's Manual
Contents
1. not exceed 104 F 40 C While installing a rackmounted unit do not block or otherwise restrict airflow to the front or rear vents To maintain rack stability consider the mechanical loading of the rack to ensure a low center of gravity Before installing a unit into a rack consider the overall loading of the branch circuit supplying power to the rack Ensure that a reliable grounding path is maintained in rack system This unit is intended to be connected to earth ground Installing the Rail Assemblies to the Rack The rackmount kit contains two rail assemblies that you mount to your rack 1 Open the shipping carton remove the rail assemblies and associated hardware Verify that you have all the components listed in What s in the Box 2 If you have non threaded racks slide four clip nuts onto the rack where you are installing the rails two on the front and two on the back of the rack If you have pre threaded racks skip this step 3 Position the rail assemblies to your rack matching the holes on the front and back of the rails with the holes on your rack 4 Using a 2 Phillips head screwdriver attach the rail assemblies to your rack with four Phillips screws two screws on the front and two on the back of the rack or with the appropriate screws for your rack Note the front of the rack illustrated in the following figure FastStor 2 Installing or Removing a Barcode Reader 3 Installing t2. FastStorTM 2 6 00519 01 Rev B May 2005 ADIC ADIC Scalar and SNC are registered trademarks of Advanced Digital Information Corporation All other product company or service names mentioned herein are the property of their respective owners Racking or De racking the Autoloader You can convert your FastStor 2 autoloader from a desktop to a rackmount configuration or from a rackmount to a desktop configuration Contents What s in the Box The following items are included in the rackmount kit Tools Required The following tools are required to work with the rackmount kit Page Topic 1 What s in the Box 1 Tools Required 2 Converting from Desktop to Rackmount 5 Converting from Rackmount to Desktop 6 Contacting ADIC Description Quantity Phillips screws 10 Clip nuts 10 L brackets right side and left side 2 Rail assembly right side and left side 2 Description Quantity Small flat blade screwdriver 1 2 Phillips head screwdriver 1 2 FastStor 2 Installing or Removing a Barcode Reader Converting from Desktop to Rackmount When converting a desktop autoloader to a rackmounted unit you must install the rail assembly onto the rack attach the L brackets to the autoloader and then install the autoloader into the rack Before you begin review the following guidelines For continued safe operation the recommended maximum internal ambient temperature of the rack should
3. he L Brackets to the Autoloader The rackmount kit contains two front L brackets that must be installed to the autoloader before you can rackmount it 1 Turn off the autoloader and then remove the SCSI cable s and power cable from the rear of the autoloader 2 Using a small flat blade screwdriver remove the front two screws that secure the right side and left side of the autoloader cover 3 Save the screws for step 5 4 Position the L brackets to the side of the autoloader as shown in the following figure by matching the holes on the brackets to the holes on each side of the autoloader cover Using the following figure verify that the hole on the front flange is placed at the top 5 Using a small flat blade screwdriver attach the L brackets the autoloader with the screws from step 2 Installing the Autoloader to the Rack Once you attach the L brackets to your autoloader you can slide the autoloader into the rails 1 If you have a non threaded rack slide two clip nuts onto the rack where you are installing the autoloader If you have a pre threaded rack skip this step 2 Position the autoloader in the rack by sliding it into the rail assembly and matching the holes in the rack with the holes on the L brackets 4 FastStor 2 Installing or Removing a Barcode Reader Make certain that the restraint tabs at the rear of the rail assembly slide into the back of the autoloader and that the L bracket is fully seated against the f
4. rews from step 5 back into the front right and left side of the autoloader to secure the autoloader cover 7 Reconnect the SCSI cable s and the power cord to your autoloader Refer to the FastStor 2 User s Guide Your autoloader is now ready for use as a desktop unit Store the screws L brackets clip nuts if applicable and rail assemblies in a secure location in case you want to rackmount your autoloader again Contacting ADIC If problems cannot be solved with the aid of this document or if training is desired contact the ADIC Technical Assistance Center ATAC In the USA 800 827 3822 In Europe and Japan 00 800 9999 3822 For other contact numbers www adic com contact To open a Service Request online www adic com techsup
5. ront flange of the rack 3 Using a 2 Phillips head screwdriver attach the L brackets on each side of the autoloader to the rack with the two remaining Phillips screws or with the appropriate screws for your rack 4 Reconnect the SCSI cable s and power cord to your autoloader Refer to the FastStor 2 User s Guide Your autoloader is now ready for use as a rackmounted unit FastStor 2 Installing or Removing a Barcode Reader 5 Converting from Rackmount to Desktop When converting a rackmounted autoloader to a desktop unit you must first remove the unit from the rackmount assembly and then remove the L brackets from the autoloader 1 Turn off the autoloader and remove the SCSI cable s and power cord from the rear of the autoloader 2 Using a 2 Phillips head screwdriver remove the screws that secure the L brackets to the rack Store the screws in a secure location 3 Slide the autoloader out of the rack and set it on a cleared flat work surface 4 Using a 2 Phillips head screwdriver remove the rail assemblies by removing the screws and clip nuts if applicable that secure them to the rack Store the screws and clip nuts if applicable in a secure location 5 Using a small flat blade screwdriver remove the screws that secure the L brackets to the front of the autoloader two on each side Store the L brackets in a secure location 6 FastStor 2 Installing or Removing a Barcode Reader 6 Re install the sc
Download Pdf Manuals
Related Search