Quantum DPA Poster
Contents
1. CP3100 Installation Set up Procedure This procedure provides step by step instructions for installing an Internal CP3100i 160 Please refer to the other side for instructions on installing CP3100 Installation Set up Procedure This procedure provides step by step instructions for installing a Desktop CP3100D 160 CP3101D 160 and the 1U Rackmount CP3100R1 160 CP3100R1 320 Please refer to the other side for instructions on installing an Internal CP3100i 160 Please read the instructions completely before beginning the installation process a Desktop or the 1U Rackmount version of the CP3100 Please read the instructions completely before beginning the installation process Copyright 2003 by Certance LLC All Rights Reserved Certance and the Certance logo are trademarks of Certance LLC Other product names are trademarks or registered trademarks of their respective owners Certance reserves the gl t to change without notice product offerings or specifications No part of this publication may be reproduced in any form without written permission from Certance LLC e Part number 10011091 001 December 2003 Power Cord Required tools Phillips screwdriver Installing2. Figure 3 8 Connect the provided VHDC 1 to HD68 Archive Cable to the Setting up a Rack Mount CP3101R1 160 CP3101R1 320 Feed n ee lower Host Archive port Figure 4 Use the following procedure to get a rack mount CP310R1 160 9 Attach the center connector on the Archive cable to your CP310R1 320 up and running existing DDS 4 or DAT72 Archive Tape Drive Attach the 1 Unpack the contents and check for damaged items If any of the provided terminator to the last SCSI connector on this cable contents are damaged contact Certance immediately Otherwise zp T Figure 5 proceed to the next step eT CE 10 Connect an existing SCSI cable trom CPU mainboard or SCSI 2 Shut down the computer and disconnect the AC power cord adapter card to the VHDC 1 to HD68 converter Figure 6 and 7 3 Mount the unit in a Certance recommended rack mount slide such 11 Connect one end of the provided Ethernet cable s connector ae ena or General Devices Power Cord SCSI Cable into the GbE 1 port Figure 8 4 Connect an LYD Male HD68 SCSI cable not provided to the Figure 6 12 The other end of the Ethernet connection cable is attached to a SCSI IN port on the rear panel Inot PCI bracket Secure the Ethernet PCI bracket to an ae PCI If you purchased the CP3101D 160 you must also connect the slot in the Host computer s back plane Confirm that the Desktop unit to a DDS 4 or DAT 72 approved tape archive Ethernet connector and cable do not come in contact wi
3. an Internal CP3100i 160 Use the following procedure to get an internal CP3100i 160 up and running Unpack the contents and check for damaged items If any of the contents are damaged contact Certance immediately Otherwise proceed to the next step Setting up a Desktop CP3101D 160 CP3101D 320 Use the following procedure to get a desktop CP3101D 160 CP3101D 320 up and running Unpack the contents and check for damaged items If any of the contents are damaged contact Certance immediately Otherwise proceed to the next step Connect an LVD Male HD68 SCSI cable not provided to the SCSI IN port on the rear panel If you purchased the CP3101D 160 you must also connect the Desktop unit to a DDS 4 or DAT 72 approved tape archive device This can be accomplished by connecting an LYD Male HD68 SCSI cable to the ARCHIVE SCSI port on the rear panel Power Cord j ARCHIVE NETWORK NETWORK Gbe1 Gbe2 SCSI IN 2 Shut down the host computer and disconnect the AC power 3 Terminate the SCSI chain as appropriate for your configuration if 7 SCSI Cable Fiowel Fisure cord this unit is the last device in the SCSI chain connect the provided g g P SCSI terminator to the SCSI OUT port If this is not the last device 3 Please Note It is not necessary to manually set the SCSI ID in the SCSI chain connect a SCSI cable to the SCSI OUT port number of the CP3100i 160
4. 3100i 160 RemoteAdmin configuration tool and complete configuration of the clock password network 10 Install the supplied Yosemite TapeWare software if you prefer to and email settings use it as your backup software application For more information l l l refer to the Yosemite online manual that was provided with the 18 Load a tape cartridge into your tape drive and then proceed TapeWare software Figure 9 Figure 10 to perform your backup and restore operations In Register the unit at http register certance com
5. Internal unit The unit will assume and terminate the last device the SCSI ID of the archive tape drive after connection and boot Up 4 Connect an Ethernet cable from your existing Local Area Network LAN to the NETWORK GbE 1 port 4 Select an available 5 25 inch half height mounting bay remove the front panel and install the unit in the mounting bay 5 Attach the power cord to the AC Power receptacle on the back of by sliding the unit through the front of the computer Figure 1 the unit VDC convener 5 De Se the model of your host computer each 5 25 6 Set the power switch to the ON position inch bay should provide bracket hardware to mount additional Figure 3 devices However lease consult your host computer user 7 f your operating system does not recognize the Unit see the Terminator manual for proper dence installation Prior to power up the online User s Guide for troubleshooting information CP3100i 160 unit must be securely mounted in the 5 25 inch bay 8 Install the supplied Yosemite TapeWare software if you prefer to use it as your backup software application For more information 6 Connect the host DC power cable existing inside the host refer to the Yosemite online manual that was provided with the computer to the power connector Figure 2 TapeWare software VHDC 1 connector 7 Connect the provided VHDC 1 to HD68 converter to the 9 Register the unit at http register certance com CP3100i 160 Host SCSI port upper port
6. th device This can be accomplished by connecting an LYD Male surrounding cards Figure 9 HD68 SCSI cable to the ARCHIVE SCSI port on the rear panel 13 Connect an Ethernet cable from your existing Local Area joes hene connecion Y g 5 Terminate the SCSI chain as appropriate for your configuration if ADG e Network LAN to the Ethernet PCI port on the back of the Host this unit is the last device in the SCSI chain connect the provided y computer Figure 10 SCSI terminator to the HOST SCSI OUT port If this is not the last device in the SCSI chain connect a SCSI cable to the HOST SCSI 14 Re attach the Host computer s AC power cord Turn on the OUT port and terminate the last device Host computer If your operating system does not recognize the Figure 8 unit see the online User s Guide for troubleshooting 6 Connect an Ethernet cable from your existing Local Area Network information LAN to the NETWORK GbE 1 port 15 Install the supplied Yosemite TapeWare software if you prefer 7 Attach the power cord to the power receptacle on the back of to use it as your backup software application For more hence A information refer to the Yosemite online manual that was Y provided with the TapeWare software 8 Set the power switch to the ON position 16 Register the unit at http register certance com 9 If your operating system does not recognize the unit see the l l l l l online User s Guide for troubleshooting information 17 Log into the CP
Download Pdf Manuals
Related Search