Home

Q-See QSHI3512 Technical Manual

1. 54 95311 ETZGohtrol eei ierit ee te etae p TG e Ob OV EUER 54 9 1 2 3D Intelligent Positioning Key ooococioninncnncnnococccnncocnccnononncnnononncnnononnon no nennen enne ener ener enne 55 9 1 3 Preset Setup and Operation esses ener enne aina aaa aa aaa aaa 56 9 2 From DVR Menu to Dome MENU 0 000vteetertereotentesesooooeooenoooeoooneooenooneooonooneooenoonoooennonoooennonoooonnonoooonnonoooonnen 57 9 3 Network Keyboard Operation for PELCO P D P 1 D1 eee eese ee esee reete enne tete ene ete esse 57 9 3 1 Keyboard Setup e eei emt teet iet n eie t oed eit ob e erdt i d ence 57 9 3 2 Menu Operativa RERO HERES 58 9 4 Scan Tour Pattern for PELCO P D P1 D1 eee eee eese ente enne tete seses sese seses seses esse 59 9 41 Via PRES Ob ssa deyo eevee i ete aate diei Gr eed aui aa ed ite ERE dre ce mae 59 9 4 2 Mia Dome Menus cte etaed k bes ba etiim eed id are aes 60 10 V or 63 10 1 Daily Eine M i 63 10 2 Problems and SOIlUtiONS 0000r00e0eseerereotaresenosooooooosososoooososoosoooovosonoaoosesoovosoneaoooosoovosoooaoosoooovosonoaoosoooonaaonoaon 63 Welcome Thank you for purchasing our integrated speed dome system This operating manual is designed to be a reference tool for the installation and operation of your system H
2. Ask for electrical engineer Self diagnosis is ok No video signal Power supply board connection is too loose connect tightly Check the circuit connection Connect again Video switch connection is wrong or mishandle Please refer to operating manual cable connection Self diagnosis is ok Dome is out of service Control circuit is not properly connected check control connection Dome address protocol or baud rate setup is not right Please refer to operating manual chapter two protocol baud rate address setup Video signal loss occurs in high speed Power supply is not sufficient change power supply board Video signal is not successive Circuit connection is too loose Connect tightly Video switch or power problem Ask for electrical engineers Video is not clear Focus is in manual mode Control manually Dome cover is dirty Wash dome cover 63 During camera switch there is a tilt movement in the monitor Camera power is not in the same Phase When several domes are connected to one transformer please connect the transformer output cable to the domes same side 64
3. Open a hole in the ceiling Locate the centre point Cut the circle of the mounting out of the location and insert the ceiling compass tool Draw a circle dimension about 225 2mm Note The ceiling thickness should be within 0 8CM to 4 2CM In diameter 225MM section it should support at least 20KG Step2 Set address baud rate and protocol Remove the protect pads Note reserve these pads for future use When you ship the dome back to the factory please insert these pads again Set address baud rate and protocol Please refer to chapter two 24 Step 3 Cable connection O Step 4 Mount the dome to the ceiling Push bracket anchors of the shell to insert the dome core When the bracket anchors are fully pulled in open the bracket anchors and fix the bolt in white cable centre Please f 1 ensure you have mount the dome core in the ceiling tightly Please refer to chapter three cable connections Note For security reasons a prevent belt i OO N is needed between the dome cover and o 4 the ceiling The prevent belt is not Sg The safety steel wire included in the accessory package SIEP AM Ne ee dame Match the slit the camera fixing bracket with the lock on the camera and mount the camera onto the camera fixing bracket Turn the camera in the lock direction until the lock tab of the camera fixing bracket meets the lock line of the camera Remove
4. SET RIGHT LIMIT DEFAULT SPEED 011 RUN STOP BACK EXIT 1 Scan setup 1 In DVR PTZ control menu call preset 28 or 95 System pops up dome menu and dome enters menu scanning Click page switch button system enters PTZ control page Up down left right keys become menu direction keys the icon ki near the IRIS becomes enter button Move the cursor down to highlight FUNCTION SETTING then click confirm Icon EJ near the IRIS System now goes to function setup menu 2 In function setup menu you can set preset auto scan touring pattern Highlight AUTO SCAN and click confirm button The dome is ready for you to set pattern 3 Move cursor to highlight Auto Scan NO and use left right keys in dome PTZ control interface to adjust value The value ranges from 001 to 005 Move cursor to highlight set left limit and then click confirm button Icon Ed near IRIS System pops up OK to alert you that you have set left limit Move the cursor to highlight EXIT and click confirm button Icon li near IRIS Now the up down left right keys become PTZ control key You can move dome to another location 4 Repeat procedure 3 again to set right limit Move cursor to highlight default speed now you can use left and right key to adjust scan speed Move cursor to highlight run or stop and click confirm button Icon ki near IRIS to begin or stop scanning 60 9 4 2 2 Tour setup SYSTEM INFORMATION CAMERA PARA
5. Figure 40 Preset setup 7 3 2 Activate Preset In Figure 39 please input preset number in the No blank and click preset button 46 7 3 3 Patrol Setup Tour setup In Figure 38 click patrol button The image is shown as in Figure 41 Input preset number and add this preset to a patrol tour For each patrol tour you can input 80 presets x X PANTILT IZOOM ctio 0 Pattern Add Preset Border Del Preset Figure 41 Patrol setup 7 3 4 Activate Patrol tour In Figure 39 input patrol tour number in the No blank and click patrol button 7 3 5 Pattern Setup In Figure 38 click pattern button and then click begin button The image is shown as in Figure 42 Then you can go to Figure 35 to modify zoom focus and iris Go back to Figure 42 and click end button You can memorize all these operations as pattern 1 W PANTILT ZOOM X Function Preset Patrol Pattern Border Figure 42 Pattern setup 7 3 6 Activate Pattern Function In Figure 39 input mode value in the No blank and click pattern button 7 3 7 Auto Scan Setup In Figure 38 click border button The image is shown as in Figure 43 Please go to 47 Figure 35 use direction arrows to select camera left limit Then please go to Figure 43 and click left limit button Repeat the above procedures to set right limit Figure 43 border setup 7 3 8 Activate Auto Scan In Figure 39 click Auto Scan button the
6. Object is not at the centre Near and far objects are not clear at the same time Objects with strong rays such as neon light or spotlight Fast moving object Large barren section such as wall Object is dark or blur 2 3 3 Aperture Control Aperture control is to control image light Click OPEN or CLOSE key to modify 11 Aperture will go back to auto mode after initialized or pan tilt movement or zoom 2 3 4 Auto Backlight Compensation This function allows you to balance brightness and darkness sections of the image to produce a more vivid picture 2 3 5 Auto White Balance Automatically change color in accordance with environment light Here you can also modify manually 2 3 6 Day Night Switch Automatically change camera mode between day night to get vivid resolution In daytime camera is in color model and at night camera is in black and white mode 2 4 Preset and Recall Preset function is to save the address information such as PTZ pan tilt focus and etc to the memory so that users can quickly adjust the dome and PTZ to the correct position Here dome supports 80 presets 2 5 Auto Touring Add addresses into a routine in a desired order Set time and stop duration for each address The dome will begin an auto touring between these addresses Here you can input maximum 80 presets in one touring 2 6 Auto Scan Auto scan is to scan selected area at the same frequency Here you needs to set left and right limit and interval There
7. are maximum five auto scan channels 2 7 Auto Pattern Auto pattern is to memorize PTZ movement and camera focus From the starting point camera move around from the started point at the same interval 2 8 Window Blanking Privacy Mask Window blank is to hide some zones for privacy reasons Please use OSD menu to setup 2 9 Alarm Input and Output Here users can set 7 alarm input alarm time and alarm clearance time 12 3 Protocol Baud Rate Address setup 3 1 Protocol and Baud Rate Setup Please configure the following settings before begin controlling dome e Protocol e Baudrate e Address Note All the setup will only become activated after restart system Open the lower dome the image is shown as below A AAC Ns 4 e in A E SL ZO S Protocol Baud rate Parity 1 2 3 4 5 6 7 8 Figure 1 Protocol baud rate and parity 1 4 is for protocol 5 6 for baud rate and 7 8 for parity Please refer to Figure 2 to Figure 4 for detail information OFF OFF OFF OFF DH SD ON OFF OFF OFF DAHUA OFF ON OFF OFF PELCO D ON ON OFF OFF PELCO P 13 X X X X Reserved Figure 2 protocol sheet Baud Rate 9600bps 4800bps 2400bps 1200bps Figure 3 Baud Rate sheet Figure 4 Parity sheet 3 2 Address Setup Address 1 2 3 4 5 6 7 8 Figure 5 Address setup Address c
8. from 1 to 255 Note You can not use menu to modify address 6 4 2 Camera Setup DIGITAL ZOOM MANUAL FOCUS AUTO IRIS BRIGHT BLC WB MODE R GAIN B GAIN BACK EXIT Figure 22 Camera setup Highlight PARAMETERS CAMERA and click confirm button DIGITAL ZOOM There are two digital zoom settings auto or manual MANUAL FOCUS There are two manual focus settings auto or manual BRIGHT click left or right key to change camera brightness BLC Back light compensation function There are two settings on or off WB MODE White balance function There are two settings on or off R GAIN This function only becomes activated when WB MODE is set to manual mode B GAIN This function only becomes activated when WB MODE is set to manual mode 6 4 8 Dome Function Setup 35 PRESET AUTO SCAN TOURING PATTERN PRIVACY MASKING BACK EXIT Figure 23 Dome function setup Back to main menu and highlight FUNCTION SETTING click confirm button The screen is shown as in Figure 23 6 4 3 1 Preset setup PRESET NO 001 TITLE PRESETOO1 SETTING CALL BACK EXIT Figure 24 Preset setup Move joystick to highlight PRESET button e PRESET NO move left or right key to modify preset number The value ranges from 1 to 80 e TITLE Title text is the label used for you to identify the camera System will automatically name a title for the camera SETTING highlight setting and click confirm button The
9. system will pop up a message PRESET Here means preset number And the SETTING column pops up an OK Now you successfully add a preset Repeat the above procedures to set more presets CALL Here is to recall preset Highlight CALL and then click confirm button to go to a preset 6 4 3 2 Auto scan AUTO SCAN NO 001 SET LEFT LIMIT SET RIGHT LIMIT DEFAULT SPEED 011 RUN STOP BACK EXIT Figure 25 Auto scan 36 Move joystick to highlight AUTO SCAN click confirm button AUTO SCAN NO Here is to set auto scan number The value ranges from 1 to 5 You can click left right key to configure SET LEFT LIMIT Here is to set camera left address SET RIGHT LIMIT Here is to set camera right address RUN Here is to activate auto scan function STOP Here is to terminate auto scan function 6 4 3 3 Touring TOURING NO 001 DWELL 005 PRESET NO 001 ADD PRESET REMOVE PRESET DELETE TOURING RUN STOP BACK EXIT Figure 26 Touring TOURING NO Here is to ser tour number The value ranges from 1 to 8 You can click left right key to configure PRESET NO Here is to show preset number There are maximum 80 presets in one tour You can click left right key to configure ADD PRESET Here is for you to add a preset Input preset number in PRESET NO and highlight ADD PRESET click confirm button to add one preset into the tour REMOVE PRESET Here is to delete a preset DELETE TOURING Here is to d
10. B Effective Pixel 768 H 494 V 795 H 596 V Horizontal Resolution 480TVL 540TVL Fan and Heater Auto Manual Auto mode has the priority Humidity lt 90 Environment 40 C 60 C outdoor 10 2 Dome Function Setup There are two ways to implement dome setup e Keyboard or Matrix e Onscreen display menu If you are using keyboards or matrix please make sure the following items in dome and keyboard matrix are the same e Address e Baudrate e Parity e Protocol Please check the connection lines before the setup Note All the instructions here are based on the general keyboard 2 1 Dome Address Dome only responds to the order of the same address Hard address Please refer to 3 2 address setup 2 2 PTZ Control 2 2 1 Pan and Tilt Movement Move joystick to control the PTZ movement 2 2 2 Proportional Pan and Tilt Continually decrease or increase pan and tilt speeds in proportion to depth of zoom 2 2 3 Auto Flip Rotates dome 180 degrees at the bottom of tilt travel 2 2 4 3D Location Click one point current video will be displayed in screen centre Drag current section to zoom in or zoom out DVR needed here 2 3 Lens Control 2 3 1 Lens Control Use control key usually are TELE and WIDE to adjust image focus 2 3 2 Focus Control Use Far and Near key to adjust focus Focus will go back to auto mode after initialized or pan tilt movement or zoom Note auto focus function is off in the following conditions
11. DEESD za A acted eto bam nte fct orte nd et eda 32 6 3 2 FOor PEECO P D ure eon Up an 33 6 4 LEN EIE E RA 33 6 4 1 Dome Information Setup r 33 0 4 2 Camera Setup e Saisie ats ea nbs ee e eL a eee 35 6 437 Dome FUNCHON Setup cree Ree te 35 6 4 4 Alarm Setups anh e aem Sa oth enin na es eR atate 41 64 5 Device Conttol i ue eene eene enne de ee een 41 6 5 Dome abnormal Phenomenon Operation eee eese eere ee eene seses ease ease enses eae ee 42 6 5 1 Restore to Factory Default Setup sss eene onon aaa aaa trennen eene nnns 42 6 5 2 PTZ Movement is not so Smoothly sess eene entente 42 0 5 3 Focus IS Bl te ren pre recht e ba eR EB ERREUR en ese ey 42 Y DVR CONNECTION AND SETUP ooo no sano rane ere ro ono opua eue e ruo kounouk pase nsestons 43 7 1 Cable Connectloh rer rer terere do a i ue ries a i tede i i i ee iere i e rete epe o a i 43 7 2 PA ON 43 7 2 1 3D intelligent positioning Key eessseeseseeseeeennrenennenn nennen onon aaa aaa aaa aaa aa aaa aaa 45 7 3 Preset Patrol Pattern Scan Function cssscssssccsssccesecssscsssscsesecsssesscscsesecsssesscsssesecssessssesesecessessrsesee 45 TIT Preset Setup a Cea e ri nte ee qiie et a dem be T 46 13 21 Activate Preset ern eet ht ere hi m eei tae 46 3 8 Patrol
12. DVR menu For PELCO P D user you can operate preset setup recall and tour recall via DVR PTZ menu You need to operate scan setup recall and tour setup via dome menu 9 1 3 1 Setup Preset setup interface is shown as in Figure 49 e Firstly move the camera to the location you need e Secondly click preset button and then input corresponding value e Finally please click save button to save one preset 9 1 3 2 Operation In Figure 47 click Page switch button The image is shown in 441 4342151 o Please input corresponding value in NO And then click preset Please refer to chapter 7 3 preset patrol pattern border for detailed information You can use dome menu to add presets and use DVR menu to recall W PAN TILTIZOOM X Function Preset Input value here Preset Patrol No 0 Patrol La Pattern Set Border Del Preset Figure 49 Preset setup 56 A PANTILT ZOOM X No 0 Input value here Preset Patrol Pattern Aux On AutoScan Aux Off AutoPan Light On Page Switch Figure 50Preset operation 9 2 From DVR Menu to Dome Menu In Figure 50 input preset value 28 or 95 and click preset button System pops up dome menu please click page switch You can see an image shown as below See Figure 51 Now you can use direction keys on the left as menu direction keys up down left right Icon ki near IRIS is confirm button You need to exit if you want to control PTZ movement again Highlight exit k
13. High Speed Dome User s Manual Table of contents 1 FEATURES AND FUNCTIONS 3 a usedecuse seo ve udo adan 8 1 1 FEALUF S DET 8 1 2 A M 8 1 2 1 On Screen Men itin 32 2 aio e iO P E p a RH 8 1 2 3 Support multiple protocols function sess eene ener ennt entren enne enn 8 1 2 3 Proportional Pan and Tilt 3 2 5 rm tt ae a ati haa a eit ni ete den 8 1 2 4 On screen TIPS outer iba ee eap ra Poe dee 8 1 2 5 Preset Setup and Recall sisse eene ener ethernet trennt enne nenne nennen nnne 8 1 2 6 SAULOES COIN aee enema eda i nem e neat edem ic i am id eed 8 15277 Auto TOUR 8 1 2 8 Auto Ra 9 1 2 9 Window Blanking iii siai si erro ono 9 1 2 10 Actlion on AVACAN k vive ko eee idea ke ei anan Pe kal ke a e rl ka KEN D YU IER re Ee RR e xe dr ERR A vien 9 1 2 11 Auto Flip and IS Camera support needed sse aa aaa aaa 9 1 2 12 Self diagnosis estet er iere er tene diede er e o ka bobin da b kep edere do ie toe an 9 1 2 13 Day Night Mode eoi prote ete e Rot bee mette pe rote me rte reae RE 9 1 2 14 Auto FOCUS iia eter edite ee eu mi nr ite ett 9 1 2 15 Backlight Compensation aaneren eaae atene EEEE EE EEEE EAE sa ena one sa ona EE EE AATE 9 1 2 16 Pati Tilted ZOO zii iii r ia Hearne ERR hr RE Ts Te 9 1 2 17 3D DocatlOnm s a RAR d 9 1 2 18 KEES Eii 9 1 3 ARTO 10 2 D
14. METERS DFUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT PRESET AUTO SCAN TOURING PATTERN PRIVACY MASKING BACK EXIT TOURING NO 001 DWELL 005 PRESET NO 001 ADD PRESET REMOVE PRESET DELETE TOURING RUN STOP BACK EXIT Tour setup 1 In DVR PTZ control menu call preset 28 or 95 System pops up dome menu and dome enters menu scan Click page switch button system enters PTZ control page Up down left right keys become menu direction keys icon Ed near the IRIS becomes enter button Move the cursor down to highlight FUNCTION SETTING then click enter icon near the IRIS System now goes to function setup menu 2 In function setup menu you can set preset auto scan touring pattern Highlight AUTO SCAN and click confirm button The dome is ready for you to set pattern 3 Touring NO Move cursor to highlight TOURING NO and then use left right keys to adjust value The value ranges from 001 to 008 seconds DWELL Move cursor to highlight dwell and then use direction key s to adjust value The value ranges from 003 to 255 PRESET NO Move cursor to highlight preset no and use left right key to adjust value The value ranges from 001 to 080 ADD PRESET Move cursor to highlight add preset and then click confirm button icon Ed near IRIS Move cursor to highlight preset no to modify preset value Now you can add the preset to proper touring NO then move cursor down to highlight
15. NTER e Secondly input 5 in tour point and click ENTER Now you have deleted tour point 5 e Thirdly input 6 in tour point and click ENTER You have deleted tour point 6 8 4 5 PATTERN 8 4 5 1 Pattern setup e Move cursor to highlight pattern and then input pattern value Pattern Value 1 Input value is the pattern path you want to set Maximally Patter setup gt Start support five paths Click ENTER to confirm Rotation Stop e Move cursor to highlight start and then input pattern value Now click ENTER to confirm Tour Value 1 Tour setup Speed Add to tour duration Remove tour gt Remove tour group Tour Tour setup gt tour group 1 Add to tour point Tour point Remove tour point e Move cursor to highlight stop Input pattern value and click Pattern Value 1 ENTER to stop pattern Dome will automatically memorize Pattern setup gt Start all the operations you have done Rotation Stop 8 4 5 2 Pattern operation e Pleas use up down keys to highlight pattern When cursor is before start please input pattern value and then click ENTER to begin pattering e Move cursor to highlight stop and then click ENTER System stop pattern 8 4 6 Pan Rotation Move cursor to highlight speed Input speed value the speed you want and click ENTER Then move cursor to highlight start and then click ENTER Dome Pattern Value 1 Pattern setup Start Pan rotation Stop begins pan rotation gt Speed Move curso
16. OME FUNCHON SETUP rana a pa yn eran ec andrea aka do aaa ken des kasa iais 11 2 1 DAA ONO 11 2 2 PTZ COntrol k wi skin si ta ui in saa na bade A ao k andan i i i o i 11 22 1 Pan and Tilt Moverient i emet id 11 2 2 2 Proportional Pan and E nono ern ennt enn ennt en nana sete nen 11 PAPA lt AUTO lc e eme e eto eft i a emt eid s 11 2 245 3D Location o EN UE 11 2 3 Lens Controlnariin sana i a i i a i i i N A 11 231 O 11 23 2 FOCUS CONTO I kone terea va da ak ayo a peso ree viret e pako Pa reb Ea ere pea See 11 2 9 9 Aperture Control scorre eundem eei eed ee ie vides 11 2 34 Auto Backlight Compensation essent nnne treten a aaa 12 2 3 5 Auto White Balance or ok evoke dead vierten a 12 2 3 6 gt Day Night Witch cicatrices 12 24 Preset and Recalde ease o sai orae kou das se DU a s T o si Oo ek Do a PS ina Ke Pe oa eee ek dn aises 12 2 5 Auto TOUFING PE sa ski ki a k i i o i i i o k i i a k o 12 2 6 Auto SCAM A sia ss is iii i is iais i i is a Za i i i i Ta is T ss ss is 12 2 7 Auto Pattern RAN 12 2 8 Window Blanking Privacy Mask ssssssscssssssscssessssessessesessessesesnessssecnessesecnessesesnessesesessesecnessesessesseseseens 12 2 9 Alarm Input and Output ccscssssccscsscscssesscscssessesesnessessesessesssseenessssessessesecessesecessesesessesesessesecesseseseesees 12 3 PROTOCOL BAUD RATE ADDRESS SETUP ccsssssssessesene
17. Setup Tour setup esc ene erede eder e n e He ed k e redeat ee e 47 1 39 4 Activate Patrol COUN bse E Ee E RR RERO RR RR RR RERO 47 1 3 5 Pattern Setup niente O ee eed i ti pa id epi nd 47 7 3 6 Activate Pattern FUNCOM ener enne ennt ener innen 47 7 3 4 Auto Scan Setup usi RUE HR NO e e NOR HIT a a i ATI RR OE a EH 47 LO ActiVate AUtO S CAM cm e ette te ta ai a E a a i 48 7 4 Dome Menu Control ert i p skiais ss aisas pisaiada d sad od aiskiai ai ai ps a aa i 48 8 NETWORK KEYBOARD OPERATION BASED ON DH SD 49 8 1 Dome and Network Keyboard Connection cccssssssssssscecssssccessssscsessesscsesssssssesssssssecsessesessesseseoses 49 8 2 Network Keyboard Setup before OperatioN o oocoommmmmmssssso 49 8 3 Menu and Key Introduction seansen soisissa nesesario enosis onor nii oaos sas aSo 49 8 4 Network Keyboard Operation e esesesesescsescscscscscscececscsescsesesescsescecscececscsescscecsesesesescscecscscsesesesesesesesesesesesee 51 8 41 Direction Setup oreet is 51 842 PIeS L Lini NN 51 Bu3 SOCAN assess aa hates A aa L a pa A O ae 51 8 44 TOUEA Leere eee NR del a i a i i i RE ia Ret si Dye ER 52 8455 PATTERN act edat amm di A EU dA IU REG ADA S ER seeks 53 84 6 Pan RotatiON ci tea etie derart ii a Woh testes 53 9 FORPELCO P D P1 D1 PROTOGQCO ODL 2 ank 1 ricorrere rer res eani nee cann rayo co asian 54 9 1 AIR CIE
18. TEM INFORMATION highlight RESTART and click confirm button This reboot will not modify all activated setup such as preset tour and pattern 6 5 3 Focus is Blur From menu to DEVICE CONTROL highlight CYCLE CAMERA POWER and click confirm button System goes on a power off operation and then resumes its original status 42 7 DVR Connection and Setup Note All the operation here is based on DH SD protocol For PELCO protocol users there might be slightly difference Please refer to chapter eight for menu operation and shortcut operation 7 1 Cable Connection Figure 32 Cable connection Please follow the procedures below to go on cable connection e Connect the dome RJ 485 port to DVR 485 port See Figure 32 e Connect dome video output cable to DVR video input port e Connect power adapter to the dome 7 2 PTZ Setup Note The camera video should be in the current screen Before setup please check the following connections are right e PTZ and decoder connection is right Decoder address setup is right e Decoder A B line connects with DVR A B line Boot up the DVR input user name and password Click system setup and then click Pan Tilt control button The image is shown as in Figure 33 Here you can set the following items e Channel select the current camera channel Protocol select corresponding PTZ protocol such as DH SD1 Address default address is 1 Baud rate select corresponding baud rate Default val
19. YSTEM INFORMATION CAMERA PARAMETERS FUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT INITIAL INFORMATION SITE INFORMATION PRESET TITLE TEMPERATURE AZIMUTH ELEV AUTO INFRARED FACTORY DEFAULT RESTART BACK EXIT INITIAL INFORMATION SITE INFORMATION PRESET TITLE TEMPERATURE AZIMUTH ELEV AUTO INFRARED FACTORY DEFAULT RESTART BACK EXIT PRESET AUTO SCAN TOURING PATTERN PRIVACY MASKING PARK MOTION BACK EXIT ALARM NO ACTION CONTACT PRESET NO AUTO SCAN NO TOURING NO RELAY OUT RESET DELAY SAVE OK BACK EXIT HEATER POWER AUTO FAN POWER AUTO CYCLE CAMERA POWER BACK Figure 16 Menu tree ADDR BAUD RATE PARITY PROTOCOL MODEL SD60XX SOFTWARE FIRMWARE BACK ADDR TYPE ADDR HARD ADDR SOFT BACK EXIT PRESET NO 001 TLE PRESETOO1 AUTO SCAN NO 001 SET LEFT LIMIT SET RIGHT LIMIT DEFAULT SPEED RUN STOP BACK EXIT TOURING NO 001 DWELL 005 PRESET NO 001 ADD PRESET REMOVE PRESET DELETE TOURING RUN STOP BACK PETE PATTERN NO 001 PROGRAM START PROGRAM STOP RUN BACK EXIT PRIVACY ZONE 001 MOVE RESIZE RK FUNCTION OFF RK TIME 003MIN RK ACTION NONE ESET NO 001 AUTOSCAN NO 001 TOURING NO 001 PATTERN NO 001 SAVE BACK DVTT The diagram shown above illustrates the overall structure of the Setup Menu Note If you are using keyboard or matrix to contro
20. add preset Click confirm button to add preset REMOVE PRESET Move cursor to highlight remove preset to delete current preset DELETE TOURING Move cursor to highlight delete touring to delete all presets 1n current tour Move cursor to highlight run or stop and click confirm button icon Ed near IRIS to begin or stop scanning 9 4 2 3 Pattern setup SYSTEM INFORMATION CAMERA PARAMETERS PFUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT PRESET AUTO SCAN TOURING PATTERN gt PRIVACY MASKING BACK EXIT PELCOD protocol pattern setup 1 Pattern setup 1 In DVR PTZ control menu call preset 28 or 95 System pops up dome menu and dome enters menu scan Click page switch button system enters PTZ control page Up down left right keys become menu direction keys icon Ed near the IRIS becomes confirm button Move the cursor down to highlight FUNCTION SETTING then click confirm icon Ed near the IRIS System now goes to function setup menu 2 In function setup menu you can set preset auto scan touring pattern Highlight AUTO SCAN and click confirm button The dome now is ready for you to set pattern 3 PATTERN NO Move cursor to highlight pattern no and use left right keys in dome PTZ control interface to adjust value The value ranges from 001 to 005 PROGRAM START Move cursor to highlight program start and then click confirm button icon Ed near IRIS No
21. an and then fix the M4 bolt on the side Now the hoisting bean is OK 27 Note add anaerobic adhesive in both sides of hoisting bean G1 1 1 to enhance water proof ability The prevent belt is not included in the accessory package Step 9 Connect hoisting bean and dome 3 gt Step 10 CELE ZE E ELE EEE gu LL Video Wir Power Wire Control Wiro Glass Step 11 cable connection Please refer to chapter three Connect video power and composite control cable through hoisting connection unit to the hoisting bean Use G1 1 2 stainless to fix dome firmly with bracket anchor and then screw four M4 4 expansion bolts tightly Note add anaerobic adhesive in dome G1 1 1 to enhance water proof ability fasten the dome on the ceiling The Sealing Rubber Connect video power and composite control cable through the groove of the hoisting bean bottom Add O ring seal or plastic pad into the hoisting bean bottom Fasten the four holes of bracket anchor into the four M6 expansion bolts in the ceiling Screw four M6 bolts firmly to mount the dome on the ceiling Use glass glue to airproof groove Note For outdoor dome please use glass glue to airproof groove for sound water proof ability 28 Step 12 Tear off protection cover Remove the protection coating from the transparent cover No Be careful Do not dirty the dome cover 29 6 Menu 6 1 Screen Menu Index 30 S
22. and Zoom Supports zoom in and zoom out during tilt and pan movement In this period focus and iris are both in auto mode to get vivid image 1 2 17 3D Location Working with DVR just click part of the current scene will be displayed in the central window and automatically zooms All of these allow you to trace precisely 1 2 18 Idle Status When there is no available order you can use menu to set dome idle status after specified duration The idle status includes turn to specified preset or go to scan tour or pattern function 1 3 Specification Power AC 24V 3A 20 Includes temperature control circuit Core Consumption 11W Heater Consumption 30W Decode Card Build in Engine stepper motor Preset Point 80 Auto Tour 8 Auto Pattern 5 Auto Scan 5 Window Blanking Maximum 24 zones according to camera core type Alarm Input Output 7 1 Information Address dome title status temperature alarm fan abnormal alarm Lens Adjust speed in accordance with lens Auto Rotation Tilt 90 rotates to pan 180 Auto Pan 0 360 continuously Manual Pan Motion 0 59 180 S Speed Preset Maximum 300 Speed Manual Tilt Motion 0 5 90 S Manual Tilt Scan 2 180 Section Control Port RS485 Baud Rate 1200 2400 4800 9600 Optional PTZ Scan Accuracy 0 06 0 015 Signal Format PAL NTSC camera mode S N Ratio gt 50d
23. arm input 1 to 7 e In alarm out NO COM NC is a normal close normal open linkage output Open close e GND is grounding cable 16 Speed dome alarm signal adopts grounding connection mode This series speed dome support two alarm input types normal open normal close You can refer to 5 4 4 for the setup Please follow the procedures below a Parallel connect the GND with com please use out sourcing power to alarm detector b parallel connect grounds of alarm detector and speed dome c connect alarm detector NC port with dome alarm in port d In dome alarm setup if contact type is normal open NO low voltage will activate alarm e In dome alarm setup if contact type is normal close NC high voltage will activate alarm Please refer to Figure 9 Alarm in public ports and power cable should be jumped out Alarm device connection terminals sva ono Teon c Speed dome alarm in connection O Alarm in 12V GND Figure 9 alarm connection 4 2 1 System Layout 4 2 1 1 General connection 17 OD Monitor Input AC 220V 110V Video Output Monitor Power Adapter Figure 10 General connection 1 ES 485 Terminal resistance on Figure 11 General connection 2 4 2 1 2 Star connection Figure 12 Star connection 4 2 2 Alarm Connection 18 thers Alarm Controller Figure 13 Alarm connection 4 2 3 Keyboard Connection You can use a keyboard to control the Dome The displa
24. ck ENTER to GOTO confirm Now you have set one preset Remove 8 4 2 2 GOTO Move cursor to highlight GOTO Input preset value and click ENTER Preset cue System goes to specified preset BORO 8 4 2 3 REMOVE BRING Move cursor to highlight REMOVE Input preset value and click ENTER Now you have removed one preset Note Some protocols do not support remove preset function You can modify to replace the previous one 8 4 3 Scan 8 4 3 1 Scan setup Scan Value 1 Scan setup gt Left limit Versatile scan Right limit Random scan Speed Input value and then move cursor to highlight left limit Or you can use joystick to move camera to left limit and then click ENTER 2 Repeat procedure one to set right limit 3 Move cursor to highlight speed Input speed value and click ENTER to confirm e AN fk 8 4 3 2 Scan operation Versatile scan n D Use up down to highlight scan Input scan value and click ENTER to begin scanning Scan Value 1 Random scan Use left right keys to highlight stop Click ENTER to stop scan Valuga scanning Scan setup gt start Note for versatile scan and random scan you need Stop Corresponding protocols to support Random scan speed 8 4 4 Tour 8 4 4 1 Tour setup Use up down keys to highlight add to tour Input value in tour Tour group Tour setup gt Tour group 1 For example here we want to add tour point 2 and 3 in tour N tour Tour group 1 Remove tour e Fi
25. e mild detergent or dry cloth to clean the camera 8 About Accessories Be sure to use all the accessories recommended by manufacturer Before installation please open the package and check that all the components listed below are included in the package Dome Power adapter Bracket anchor Camera holder A pair of white gloves CD for user s manual ontact you local retailer ASAP if something is missing in your package OR E E E E E 1 Features and Functions 1 1 Features Integrated dome system has the following features High resolution integrated digital processing camera Build in PTZ and digital decode card RJ485 data port for software update Digital control and programmable Simple and effective transmission system Locate trace and scan object easily Support DH SD and Pelco P and Pelco D protocol Simple and user defined interface On screen display menu for setup of programmable functions Working with DVR to realize auto touring and auto pattern 1 2 Function Integrated dome system has the following functions 1 2 1 On Screen Menu It is easy for you to view dome information and configure dome camera parameters 1 2 2 Support multiple protocols function This series speed dome support Chinese national industrial standard and universally used protocols PELCO P and PELCO D You can use various devices and protocols to operate speed dome 1 2 3 Proportional Pan and Tilt This function keeps the image from
26. e ranges from 1 to 5 TOURING The value ranges from 1 to 8 PATTERN NO The value ranges from 1 to 5 SAVE Highlight and click confirm button to save current setup 40 6 4 4 Alarm Setup ALARM NO 01 ACTION NONE CONTACT N O PRESET NO 001 AUTOSCAN NO 001 TOURING NO 001 RELAY OUT OFF RESET DELAY 3S SAVE BACK Figure 30 Alarm setup Highlight ALARM SETTING button and click confirm button ALARM NO Here is to set alarm input Alarm input value ranges from 1 to 7 You can use left right key to select ACTION Action on alarm function It is including NONE PRESET AUTO SCAN TOURING functions You can move joystick to select CONTACT There are two alarm signal mode normal open N O and normal closed N C PRESET NO Please move joystick to set preset number The camera will turn to the preset to surveillance after alarm occurs AUTO SCAN NO Please move joystick to set preset number The camera will begin auto scan after alarm occurs TOURING NO Please move joystick to set touring number The camera will begin auto cruise when alarm occurs RELAY OUT Here is to set relay alarm mode and reset time For example OFF 5S means relay alarm function is closed and the relay will reset in five seconds after alarm occurs RESET DELAY here is for you to set alarm reset time You can use left right key to select 3 seconds 10seconds 30 seconds 60 seconds or 120seconds The dome will go back to previ
27. elete a touring Input touring number in touring NO and highlight DELETE TOURING click confirm button to delete RUN Here is to activate touring STOP Here is to terminate touring 6 4 3 4 Auto pattern 37 PATTERN NO 001 PROGRAM START PROGRAM STOP RUN STOP BACK EXIT Figure 27 Auto pattern The dome supports maximum 5 patterns and for each pattern dwell time limit is 60 minutes Highlight PATTERN and click confirm button e PATTERN NO Here is to set pattern number The value ranges from 1 to 5 You can click left right key to configure e PROGRAM START Here is to memorize pattern starting point An icon 8 pops up in screen e PROGRAM STOP Here is to set pattern stop point After all the movement highlight PROGRAM STOP and then click confirm button Now you have set one pattern The icon isappears RUN Here is to activate pattern Input pattern number highlight RUN and click confirm button system begins running pattern An icon 8 pops up in screen e STOP Here is to stop current pattern Input pattern number highlight STOP and click confirm button System begins current pattern Note The dwell time between two orders should be less than one minute Otherwise system will set to default value as one minute After click PROGRAM STOP do not click RUN button before icon amp amp disappears completely Any manual operation will terminate current dome pattern 6 4 3 5 Privacy mask W
28. ere you can find information about this speed dome features and functions as well as a detailed menu tree Before installation and operation please read the following safeguards and warnings carefully Important Safeguards and Warnings 1 Electrical Safety All installation and operation should conform to local electrical safety codes We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation 2 Transportation Security No heavy stress violent vibration or water splash are allowed during transportation storage and installation The camera could be damaged by improper handling 3 Installation Keep upwards Handle with care Do not apply power to the dome before completing installation 4 Qualified Engineers Needed All installation here should be done by the qualified engineers All the examination and repair should be done by the qualified service engineers We are not liable for any problems caused by unauthorized modifications or attempted repair 6 Environment This product has been tested and found to comply with the IP67 standard of Degrees of protection provided by enclosure IP Code The dome should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc 7 About Camera Camera should be installed away from direct sunlight or other strong artificial lights to avoid blooming and smear Only us
29. ey and click confirm Please refer to Chapter 6 Menu for more information L D PAN TILT ZOOM X Menu direction key Page Switch Figure 51 9 3 Network Keyboard Operation for PELCO P D P1 D1 9 3 1 Keyboard Setup Before operation you need to set the keyboard first Form menu to control point setup ID 0 Here you can set ID device name device type and Device name connection type Device type dome Connection type RS485 You can click ID button to enter current device connection interface Highlight connection type and then click ENTER to set 485 address 1 RS 485 Parity None 485 address is 1 and select dome protocol as Pelco P or Protocol PELCO P D P1 D1 Pelco D or Pelco P1 or Pelco D1 Stop bits Please refer to 8 4 Operation for more information Baud rate 9600 Data bits 8 9 3 2 Menu Operation Pelco P D P1 D1 is different from DH SD protocol So please pay attention to the following instructions The operations are as follows Click GOTO button to call preset input preset 28 or 95 to enter dome menu Please use up down to move cursor and left right to adjust value Click OPEN button in keyboard to confirm Open here is just the same to enter Please refer to the following sheet for more information Detailed operation instruction please see chapter 8 keyboard PELCO P D PELCO P1 D1 Enter dome Input preset 28 or 95 Press MENU menu Move t or
30. hen click confirm button to go to the third submenu Highlight SITE INFORMATION and then click confirm button to go to the third submenu e PRESET TITLE There are two settings On Off Please use left right key to select e TEMPERATURE There are two settings On Off Please use left right key to select e AZIMUTH ELEV There are two settings On Off Please use left right key to select AUTO INFRARED There are two settings On Off Please use left right key to select This function applies to some series cameras FACTORY DEFAULT Return to initial factory default setting RESTART Reboot the system BACK Go back to the previous menu EXIT leave system menu 6 4 1 1 System information ADDR 001 H BAUD RATE 9600 PARITY NONE PROTOCOL PELCO P XX MODEL SD60XX SOFTWARE 1 00 FIRMWARE 1 00 RACK Figure 20 System information Highlight INITIAL INFORMATION and click confirm button The screen is shown as in Figure 20 Here is to show dome basic information Please refer to chapter 2 for detailed information 6 4 1 2 Address setup through menu 34 ADDR TYPE ADDR HARD ADDR SOFT Figure 21 Address setup Highlight SITE INFORMATION and click confirm button ADDR TYPE there are two address types soft and hard Soft address you can use menu to modify address setup Hard address you can not change address setup here ADDR SOFT Here is to set dome soft address The value ranges
31. in pattern b After all the PTZ operation set preset 80 stop pattern c Call preset 81 to begin pattern Begin pattern d Call preset 96 to stop pattern Begin tour 3 Tour Begin auto scan Via dome menu to add preset Tour is the first one 96 Stop tour pattern scan a Call preset 82 to begin tour b Call preset 96 to stop tour 9 4 1 2 Operation when PELCO SELECT is ON 1 Scan Preset setup Function a Set preset 26 Left limit b Move PTZ Set preset 27 Right limitO C Call preset 29 to begin scan d Call preset 30 to stop scanning 2 Pattern a Set preset 22 Begin pattern b After all the PTZ operation set preset 23 stop pattern C Call preset 24 to begin patter d Call preset 30 to stop pattern vw 4 all preset Function Via dome menu to add preset Tour is the first one a Call preset 25 to begin tour b Call preset 30 to stop tour Set scan left border Set scan right border Begin pattern Stop pattern Begin pattern Begin tour Begin auto scan Stop tour pattern scan 9 4 2 Via Dome Menu Note Please do not click tilted direction key after you enter menu Other wise system will move all long You need to exit menu to stop movement highlight EXIT and click confirm button 9 4 2 1 Scan setup SYSTEM INFORMATION CAMERA PARAMETERS DFUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT PRESET AUTO SCAN TOURING PATTERN PRIVACY MASKING BACK EXIT AUTO SCAN NO 001 SET LEFT LIMIT
32. indow blank 38 PRIVACY ZONE 001 MOVE i RESIZE i ACTIVATE ON SAVE OK DELETE BACK EXIT Figure 28 Window blanking Highlight PRIVACY ZONE and click confirm button For SONY series cameras There are maximum 24 window blanking in 360 degrees System supports eight privacy zones in one screen and can only displays one blank at the same time Only display the window blank of the minimum serial number The tilt angle ranges from 0 to 70 degrees For HITACHI series cameras There are maximum 8 window blanks in 360 degrees System supports two privacy zones in one screen Tilt angle ranges from O to 45 degrees Note gt For security reasons please set privacy zone a little bit larger than the privacy object size Each time after modifications you need to highlight SAVE to get all setup activated Otherwise privacy zone may not move correspondingly with the object Please enter privacy zone menu now all the privacy zones are closed Highlight PRIVACY ZONE use left and right key to set different privacy zones For example shift to 001 section and then highlight ACTIVATE Secondly click left and right key to ON mode Now there is a privacy zone in the screen centre Thirdly use PTZ to move camera so that privacy object fit well with screen centre Fourthly highlight RESIZE and then click left and right key to adjust privacy zone direction and size Fifthly highlight SAVE and exit The privacy zone menu is show
33. ith pan and tilt functions and automatically adjust in size as the lens zooms You can set 8 blanking zones 1 2 10 Action on Alarm This series speed dome support three alarm modes There are 7 alarm inputs and 1 alarm output Alarms can be individually programmed to initiated pattern or go to an associated preset scanning touring when received Dome will return to a previously programmed state after alarm acknowledgement or to its previous position before alarm 1 2 11 Auto Flip and IS Camera support needed As long as you continue to hold the joystick in the down position the dome rotates 180 degrees and repositions itself for uninterrupted viewing of any subjects that passes directly beneath the dome IS Image stabilizer allows you to get stable video 1 2 12 Self diagnosis There is a self diagnosis procedure when dome boots up e Tilt and vertical engine check Camera diagnostics e Display dome information and diagnosis information 1 2 13 Day Night Mode Auto manual switches in low illumination Auto camera will automatically adjust CCD light level e Manual use menu or function keys to select day night mode 1 2 14 Auto Focus Auto focus allows the lens to remain in focus during zoom in zoom out and motion functions to get vivid image You can use FAR or NEAR button to adjust focus manually 1 2 15 Backlight Compensation Balance the brightest and darkest sections of a scene to produce a more vivid picture 1 2 16 Pan Tilt
34. joystick up t or joystick up cursor up Move or joystick down or joystick down cursor down ON OFF lt or joystick move left or joystick move left and modify and right and right other setup Go to sub OPEN OPEN menu Exit sub Move the cursor to highlight Move the cursor to menu back and then click OPEN highlight back and then click OPEN Exit dome Move the cursor to highlight Move the cursor to menu EXIT and then click OPEN highlight EXIT and then click OPEN Note e When you input preset to enter dome menu please click ESC on the keyboard to exit preset menu Now you can use f gt or joystick to move cursor 58 e You can only implement dome menu operation after you enter dome menu setup Exit dome menu if you wan to control PTZ movement Iris Open is working as enter button 9 4 Scan Tour Pattern for PELCO P D P1 D1 9 4 1 Via Preset In dome menu select PELCO SELECT in device control sub menu When PELCO SELECT is OFF Default you can set and call presets above 64 When PELCO SELECT is ON you can set and call preset value below 32 9 4 1 1 Operation when PELCO SELECT is OFF 1 Scan a Set preset 92 left limit Preset setup Function b Move PTZ and set preset 93 right limit Set scan left border c call preset 99 to begin scanning Set scan right border d Call preset 96 to stop scanning Begin pattern 2 Pattern Stop pattern a Set preset 79 beg
35. l direction Input value ranges from one to eight Step 8 rotation speed is faster than step 1 You can click icon E or EJ to adjust zoom focus and iris 9 1 2 3D Intelligent Positioning key Notes Only Pelco D1 and Pelco P1 support this function Pelco D and Pelco P don t have this function Click the SIT key See Figure 48 system goes back to the single screen mode When you click the mouse on the screen the point will move in the center of the screen Drag the mouse in the screen to adjust section size this can support 4 16 zoom function Dragging a rectangle from up to bottom is zooming in Dragging a rectangle from bottom to up is zooming out The zoom effectiveness varies with the zone If the zone is larger the zoom effectiveness will smaller Otherwise it will be bigger SIT Figure 48 3D intelligent positioning key You can refer to the following sheet Name Function function Shortcut Function function Shortcut key key key key Zoom Near Slow play 3 Far Fast forward Focus Near Previous LZ Far Next Iris J close E Open Replay Backward 55 Note e When you are using front panel you can just control four directions up down left right e 3D intelligent positioning function is only active with mouse operation 9 1 3 Preset Setup and Operation Note For PELCO P1 D1 user you can operate scan patter function You can add tour number via dome menu and recall via
36. l dome please ensure the control information setup such as address baud rate parity and protocol are the same with that of the dome Please ensure all the cable connections are right 6 2 System Information ADDR 001 H BAUDRATE 9600 PARITY NONE PROTOCOL PELCO P MODEL XX SD60XX SOFTWARE 1 20 FIRMWARE 2 43 CONFIGURE DONE X150 1 Y15 2 T 25 Figure 17 System information After installation please apply dome speed to power The system will go on a self diagnostics The above image will pop up to show the system information ADDR dome address Baud rate dome communication baud rate Parity communication parity bit format Protocol current communication protocol Model dome type Software software version Firmware hardware version Configure done self diagnostics is OK X150 1 Y152 2 horizontal address is 150 1 degree vertical address is 15 2 degree T 25 dome temperature is 25 C Note This screen is for reference only 6 3 Main Menu SYSTEM INFORMATION CAMERA PARAMETERS FUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT Figure 18 Main menu 6 3 1 For DH SD 32 You can enter the dome menu directly Use up and down key to view the function keys Click confirm button to go to the submenu Highlight exit button and click confirm to leave the menu 6 3 2 For PELCO P D Please recall 28 or 95 preset to enter dome menu Move joystick up and down to view function keys Press aperture zoom i
37. moving too fast when there is a large amount of zoom Dome continually decrease or increase pan and tilt speeds in proportion to depth of zoom When zooms speed is increasing the camera moving speed becomes slow When zooms speed is decreasing the camera moving speed becomes fast 1 2 4 On screen Tips Here you can view e Dome title and system version Software and hardware e Dome system temperature e Dome protocol baud rate address e Dome pan tilt coordinate preset ID 1 2 5 Preset Setup and Recall Preset function is to save the address information such as PTZ pan tilt focus and etc to the memory so that you can quickly adjust the dome and PTZ to the correct position This series speed dome supports 80 presets 1 2 6 Auto Scan Camera scans back and forth regularly in a horizontal field Here you need to set left and right limit and scan speed You can set 5 scanning paths 1 2 7 Auto Touring Add addresses into a routine in a desired order and then set time and stop duration for each address The dome will begin an auto touring between these addresses You can set 8 touring paths 1 2 8 Auto Pattern Memorize dome operation such as pan tilt and zoom to repeat Focus and iris are in auto mode during auto pattern For each pattern the time should be less than 60 seconds You can set 5 pattern paths 1 2 9 Window Blanking Window blanking is a user defined four sided area that can not be viewed by you The blank area will move w
38. n as in Figure 28 e PRIVACY ZONE Here is to set window blank Move joystick to set one window blank e MOVE Here is to set window blank location Move joystick to locate window blank in the proper point 39 e RESIZE Continue pressing confirm button to widen or narrow window blank size e ACTIVATE There are two settings on and off When activate function is on the window blank function will be activated and displays in the screen When activate function is off the window blank function will be closed and the blank will not displayed in the screen SAVE Here is to save user setup e DELETE Here is to delete setup and restore default setting Window blank function is on in default mode 6 4 3 6 Idle status PARK FUNCTION OFF PARK TIME 003MIN PARK ACTION NONE PRESET NO 001 AUTOSCAN NO 001 TOURING NO 001 PATTERN NO 001 SAVE BACK EXIT Figure 29 Idle status When there is no available order dome automatically goes on the pre set functions PARK FUNCTION There are two modes ON OFF Use left right key to set PARK TIME System idle period The value ranges from 1 to 720 minutes You can use left right key to select PARK ACTION There are several functions you can select NONE PRESET SCAN TOURING PATTERN Use left right key to select PRESET NO Here is for you to set preset number The value ranges from 1 to 80 System goes to specified preset when idle status is on AUTOSCAN NO The valu
39. n key usually it is open key to enter the submenu Highlight exit and press aperture zoom in key to leave the menu Note e For PELCO P D please exit first before you enter PTZ control e Keyboards or matrix operation may have slightly differences Please contact local retailers for more information Open the main menu the above figure will pop up See Figure 18 e SYSTEM INFORMATION Address location temperature and so on e CAMERA PARAMETERS Digital zoom focus e FUNCTION SETTING preset scan tour pattern e ALARM SETTING Alarm setup e DEVICE CONTROL Fan and heater control e EXIT Leave the system menu 6 4 Menu Operation In menu you can use the following four functions to configure or leave system menu e n main menu move joystick or use direction keys to the desired items Move left right key to configure e When current item are highlighted please click confirm button to go to the sub menu or use left right key to configure setup e Highlight back button and click confirm butto to go back to the previous menu e Highlight exit and click confirm button to leave system menu 6 4 1 Dome Information Setup 33 INITIAL INFORMATION SITE INFORMATION PRESET TITLE TEMPERATURE AZIMUTH ELEV AUTO INFRARED FACTORY DEFAULT RESTART BACK EXIT Figure 19 Dome information setup Highlight SYSTEM INFORMATION and then click confirm button to go to the second submenu Highlight INITIAL INFORMATION and t
40. oding mode adopts binary system The address value is between 0 255 Address 1 2 3 4 5 6 7 8 1 OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF oci 14 7 ON ON ON OFF OFF OFF OFF OFF 255 ON ON ON ON ON ON ON ON Figure 6 Address sheet 4 Cable Connection 4 1 RS485 and Power Cable Connection There are three cable groups here power cable RS 485 and Video cable Draw out the cables from the dome to connect with main control devices such as monitor control keyboard DVR and etc and power adapter Please refer to Figure 7 Connection sheet Red 2 pin AC 24V polarity free Black GND Yellow 485 A Green 485 B 485 GND Black Video port Video Figure 7 Connection sheet 4 2 Alarm Cable Connection Open the dome cover and take PTZ chip core out Turn the core upside down you can see the alarm port See Figure 8 Alarm n 314 M1616 7 Figure 8 PTZ chip core In Figure 8 please note e Numeral 1 to 7 is corresponding to al
41. ositioning SIT Figure 37 3D intelligent positioning key Here is a sheet for you reference Name Function function Shortcut Function function Shortcut key key key Key Zoom g Near E Far Focus 4 Near 4 E Far Iris El close 1 L Open gt 1l 7 3 Preset Patrol Pattern Scan Function In Figure 35 click the set button The image is shown as below See Figure 38 Here you can set the following items Preset Patrol Tour Pattern Border D PAN TILT ZOOM X Function Preset Patrol Pattern Border _ Preset Patrol No Set Del Preset Figure 38 Preset patrol pattern border setup In Figure 35 click page switch button the image is shown as in Figure 39 45 Here you can activate the following functions Preset Patrol Tour Pattern Aux on Aux off Auto scan Auto pan Light on A PAN TILT ZOOM x No Preset Patrol Pattern Aux On AutoScan Aux Off AutoPan Light On Page Switch Figure 39 activate function Note The following setups are usually operated in the Figure 35 Figure 38 and Figure 39 7 3 1 Preset Setup In Figure 35 use eight direction arrows to adjust camera to the proper position In Figure 38 click preset button and input preset number The image is shown as in Figure 40 Add this preset to one patrol tour W PANTILT ZOOM X Preset Patrol Pattern Border Del Preset
42. ous setup after alarm acknowledgement Please click save button after all the settings 6 4 5 Device Control HEATER POWER AUTO FAN POWER AUTO STABLE FUNC OFF PICTURE FLIP OFF PELCO SELECT OFF CYCLE CAMERA POWER BACK EXIT 41 Figure 31 Device control Highlight DEVICE CONTROL and click confirm button HEATER POWER Here is to control heater There are three settings auto on and off In auto mode system will turn heater on in 1 FAN POWER Here is to control fan There are three settings auto on and off In auto mode system will turn fan on when it is over 20 e STABLE FUNG Here is for you to set image stabilizer function There are two modes open close e PELCO SELECT This function applies for PECO P D users only Here is for users For PELCO P D users only to set shortcut options Please refer to chapter eight e CYCLE CAMERA POWER Here is to reboot camera Highlight CYCLE CAMERA POWER and click confirm button the system will reboot camera Note For security reasons when it is considerably hot or cold such as it is over 40 or below 20 system will automatically turn heater or fan on or off 6 5 Dome abnormal Phenomenon Operation 6 5 1 Restore to Factory Default Setup From menu to SYSTEM INFORMATION highlight FACTORY DEFAULT and click confirm button Dome will reboot and all the setup back to factory default setup 6 5 2 PTZ Movement is not so Smoothly From menu to SYS
43. out WIDE Lens zoom out NEAR PTZ focus zoom in FAR PTZ focus zoom out CLOSE PTZ iris zoom out OPEN PTZ iris zoom in WIPER Shortcut key to control dome rain brush LIGHT Shortcut key to control dome light 50 8 4 Network Keyboard Operation Note e X scope may not be the same due to multiple protocols e Use up down keys to control dome menu e Use left right keys to move cursor e All the operations here are based on DH SD protocol 8 4 1 Direction Setup 8 4 1 1 Speed It is to control direction The value ranges from one to eight Speed 5 Please use the number buttons of the keyboard to input value AN Zoom between 0 8 and press ENTER to confirm Operation here is Direction Focus only active with key press You can use joystick to control Iris directly Note for joystick use the speed is related to the joystick move range If the farther the joystick away from the center the swifter the PTZ moves PTZ movement direction e For joystick up down left right up left right down up right left down e For keyboard up down left right 8 4 1 2 Zoom focus lris e Zoom please use WIDE and TELE to control PTZ zoom e Focus please use FAR and NEAR to control PTZ focus e Iris Please use CLOSE and OPEN to control PTZ aperture For joystick clockwise to zoom out and anti clockwise to zoom in 8 4 2 Preset 8 4 2 1 Preset setup Preset setup gt value 1 After zoom and PTZ setup input value and cli
44. protective coating of transparent cover 5 3 Pendant Dome Installation Step 1 Draw holes Draw four holes in the desired location in the wall in accordance with the four holes of bracket anchor Bracket anchor bottom 25 Step 2 Make holes and inset bolts A MALL E E Draw four holes and screw the four p A expansion bolts ns Note Li qj 726 a p Expansion bolts are not included in the o T E A pe accessory package Step 3 Loosen bolts on both sides 2 M4 6 stainless steel bolts Take the dome out of the package use a screwdriver to loose 2 M4 6 stainless steel bolts Open the transparent cover Note Be careful Pay attention to the transparent Cover Step 4 Remove the lower dome cover P Remove lower dome cover out from the dome Note Be careful Pay attention to the transparent cover 26 Step 5 Take out pads Take out two protection pads Note Be careful Pay attention to the camera Step 6 Set address baud rate and protocol Please refer to chapter two Step 7 Attach dome cover to the dome 2 M4 X6 Stainless bolts Match the slit in the camera Attach the dome cover to the camera And then screw two M4 6 stainless bolts Step 8 Connect hoisting beam Mount the hoisting connection unit to the hoisting bean then fix the M4 bolt on the side of connection unit Then circle the hoisting rail to the hoisting be
45. protocol is DH SD After all the Baud rate 9600 setup please click ENTER to save Data bits 8 modification When you click ESC system pops up a warning Save Data dialogue Yes ENTER No ESC Click ENTER to save setup or click ESC to exit Note all the items listed here should be properly set ID device name serial port and IP are all unique Current device dome 8 3 Menu and Key Introduction RS485 address 1 ID 0 49 Click ID and then input ID system goes to current device connection dialogue box Click MENU system pops up a dialogue You can use this menu to work with dome menu 1 up 5 previous menu 2 down 6 next menu 3 Left 7 Confirm 4 Right 8 Exit Please refer to the following sheet Key Enter dome MENU menu Move cursor 1 up Move cursor down ON OFF or lt or gt select other function Enter sub ENTER menu Exit sub Highlight BACK and then click ENTER menu in keyboard Exit dome e Click ESC in the keyboard menu e Highlight EXIT and then click ENTER in the keyboard Please refer to the following sheet for keyboard function Key Function MENU Dome menu shortcut SCAN Pop up scan menu AUTO PAN Pop up tour menu PATTERN Pop up pattern menu SET Pop up preset menu GOTO System goes to preset menu REMOVE Pop up delete preset menu P T PTZ setup shortcut menu TELE Lens zoom
46. r to highlight stop and then click ENTER Dome stops rotation 53 9 For PELCO P D P1 D1 Protocol 9 1 DVR Menu Setup In DVR menu from system setting to PTZ control The image is shown as below See Figure 45 e Channel select the channel connected with dome camera e Protocol select corresponding protocol such as PELCOD1 e Address select corresponding PTZ decoder address Default value is 1 e Baud rate select corresponding baud rate for decoder Default value is 9600 e Data bits Default value is 8 e Stop bit Default value is 1 e Parity You can select to meet your own needs After all the setup please click save button PAN TILT ZOOM PELCOD1 1 9600 Copy Paste Default Figure 45 DVR PTZ setup 9 1 1 PTZ Control Note Inactive function key is in dark color You can use direction keys to adjust step zoom focus iris and preset You can double click menu title to hide menu interface After all the setup please click save button On the screen right click mouse click Fn Button in the front panel or click Fn key in the remote controller The image is shown as below See Figure 46 View 1 View 4 View 9 View 16 Color Setting Search Record Alarm Output Alarm Input Main Menu 54 Figure 46 select PTZ Select Pan tilt zoom system pops up an image See Figure 47 E D PAN TILT ZOOM X 8 Zoom 6 Focus 8 Iris a Set Page Switch Figure 47 PTZ Step is to contro
47. rstly input 1 in tour group e Secondly input 2 to tour and then click ENTER Now you have added tour point 2 to tour group 1 Tour Value 1 e Thirdly input 3 to tour and then click ENTER Now you Toursetup gt Speed have added tour point 3 to tour group 1 Addtotour Duration You can repeat the above procedures to add more tour point Removetour Remove tour group 8 4 4 2 Tour operation e Speed Please use up down keys to highlight tour setup When cursor is before speed you can input speed value e Duration Use left right keys to highlight duration and then you can input duration value e Begin touring Use up down to highlight tour and then input value Now you can click ENTER to begin tour e Stop touring Move cursor to highlight stop and then click ENTER Now you have stopped touring 8 4 4 3 Remove 8 4 4 3 1 Remove tour Tour Value 1 Toursetup gt Start Add to tour Stop Remove tour 52 Move cursor to highlight remove tour and then input corresponding value Click ENTER to delete current tour 8 4 4 3 2 Remove tour point e Move cursor to highlight tour group and then input corresponding value e Please click Enter to confirm all the operation below is active to current tour group e Move cursor to highlight tour point and input corresponding value such as 2 e Now click ENTER to delete For example you want to remove tour point 5 and 6 in tour group 2 e Firstly input 2 in tour group and click E
48. seceseesseeseeeeeenees 13 3 1 Protocol and Baud Rate Setup ssssscssssssessssssesssssssessessssessessssessessssessessssessessssessessssessessssessessssessoeseees 13 3 2 SS A iai i i ii i sous i k i i i r i i i i i i i endnotes i 14 4 CABLE CONNECTION ets as m twa n w incida A rne ior un eu diia i f 16 4 1 RS485 and Power Cable Connection vveeeeooeoooeoooooenooonooouooouoooooooooooooouooooooenooonooonoounoonoonooonoooooooooonooonooenoonnoe 16 4 2 Alarm RA AA nn TO 16 AZA System Layout ici e heo eee is A i eo dies de bobble es redes treu A i bt 17 YN AA i sias a aaa aa V aa a an tune ev aa hn ees 18 42 3 Keyboard Connection NS 19 5 INSTALLATION t ceiscea sexe o e dis edu pas cue ci dili is ai ai i i a i as 21 5 1 Surface DomeInstallatiON tes est E L asasin 21 5 2 In ceiling Dome Installation 02eerereererereoeresoossesoaoooosoooooososoooosoovosososoooosoovososeaooooooovososooooooooooosoooooonoooon 24 5 3 Pendant Dome Installation eee etntatan enean tata ta tato so tenens sata teas en sn sa en tasa se soto nn 25 Uis c M 30 6 1 Te 2BuIA3 e ai 30 6 2 System InformaltiOn eet ecc eden eet sue senio e stad EEEREN SALEEN aa ei Ue ou kode rad SEU Se aso rad GNU N suae ede ske Qo ego deas 32 6 3 A rhone mtt as dont ou a i a es ev a a e i e F e i as sont ob i A pe i as i 32 631 jEOE
49. system begins auto scan Correspondingly the auto scan button changes to stop button Click stop button to terminate scan operation 7 4 Dome Menu Control In Figure 39 click page switch button the image is shown as below See Figure 44 Click menu to enter dome menu The direction arrows here are to control dome menu Click page switch button system goes back to Figure 35 s x Enter Page Switch Figure 44 dome menu control 48 8 Network Keyboard Operation based on DH SD Note all the operations here are based on DH SD protocol You can refer to Chapter eight for PELCO protocol operation 8 1 Dome and Network Keyboard Connection Connect dome A cable with Pin 3 or Pin 7 of Keyboard 485 interface Connect dome B cable with Pin 8 or Pin 9 of Keyboard 485 Port 8 2 Network Keyboard Setup before Operation Before setup please make sure e Keyboard and dome cable connections are right e Connect dome with power source and connect dome video port with monitor e Set PTZ decoder address Set 485 address as 1 if decoder address is 1 e You have set control point ID 0 Here is for you to set ID device Device name name and device type Click ID to go Device type Dome to current device connection Connection RS485 interface 485 address 1 Move cursor to highlight connection parity None and then click ENTER System goes to Protocol DH SD RS485 setup RS485 address is 1 Stop bits 1 Default
50. to the camera Step 6 Set address baud rate and protocol Set address baud rate and protocol Please refer to chapter two Step 7 Attach dome cover to the dome 2 M4x6 Stainless bolts Match the slit in the camera Attach the dome cover to the camera body by using cross screwdriver Note be careful Pay attention to the transparent cover 22 Step 8 Pass cable through the bracket hole M4X6 Stainless Fix bracket and loosen M4 4 bolts Pass the cable out through the bracket hole in G1 screw hole Step 9 Connect dome and bracket anchor Use G1 1 2 screw bolt to mount dome M4 X6 Stainless firmly with bracket anchor Then screw bolt four M4 4 stainless bolt Note e For outdoor dome strongly recommend you to add anaerobic adhesive in G1 1 1 to enhance water proof ability e Proper anti clockwise cable when you encounter cable jam Step 10 Firm dome 1 M8 expansion To get sound waterproof effect please add rubber seal around the bracket anchor and draw cables out from the groove Then fix bracket anchor holes on the wall with the M8 expansion bolts Screw these four M8 bolts firmly Step 11 Cable connection 23 Please refer to chapter three cable connection Step 12 Tear off transparent cover Remove protection coating from transparent cover Note Be careful Do not dirty the dome cover 5 2 In ceiling Dome Installation Step 1
51. ue is 9600 Data bits select corresponding data bits Default value is 8 Stop bits select corresponding stop bits Default value is 1 Parity there are three options odd even none Default setup is none 43 z PAN TILT ZOOM X Paste Default Cancel Figure 33 Pan Tilt Zoom setup After all the settings please click save button In one window display mode right click mouse click Fn Button in the front panel or click Fn key in the remote controller The image is shown as in Figure 34 View 1 View 4 View 9 View 16 Color Setting Search Record Alarm Output Alarm Input Main Menu Figure 34 Shortcut menu Click Pan Tilt Zoom the image shows as below See Figure 35 Here you can set the following items e Step value ranges fro 1 to 8 e Zoom e Focus e Iris Click icon Id and Ed to adjust zoom focus and iris Page Switch Figure 35 Zoom Focus lris setup 44 In Figure 35 please click direction arrows See Figure 36 to adjust PTZ position There are totally 8 direction arrows There are only four direction arrows in DVR front panel Figure 36 Direction arrow 7 2 1 3D intelligent positioning Key In the middle of the eight direction arrows there is a 3D intelligent positioning key See Figure 37 Click the key system goes back to the single screen mode Drag the mouse in the screen to adjust section size lt can realize PTZ automatically We usually call it 3D intelligent p
52. w system pops up OK to alert you pattern setup begins There is a sun icon below screen 4 Repeat procedure 2 to enter dome pattern setup Move cursor to highlight program stop and click confirm button icon Ed near IRIS Now you have stopped patterning and the sun icon below screen disappears Move cursor to highlight run or stop and click confirm button Icon Ed near IRIS to begin or stop scanning 62 10 FAO 10 1 Daily Maintenance Please clean dome cover regularly to get vivid image Handle the cover with care Use water to wash Don t use cloth to clean Use mild detergent to clean if there is too much dust Note The sweat from your hand may erode plating surface your nail may scrape dome cover result in blur image 10 2 Problems and Solutions SYMPTOM CAUSE SOLUTION No self diagnosis no video signal when I connect dome to power Red LED is not on e 1 24V AC does not apply to the power Or connection is too loose e Power off or Transformer Check 24VAC power is connected or properly earthed Check power supply condition or check problem transformer Red LED light is on Use multimeter to check e 24VAC power is low dome load e Something wrong with Power supply board e Please contact retailer to change power supply board No self diagnosis There is a noise power supply is inadequate Change power supply board Mechanical failure
53. y and control can work simultaneously One keyboard can control maximum 255 speed domes Switcher EB Keyboard Figure 14 Keyboard connection 1 Speed dome protocol is open and support multiple system platforms Please contact us if some matrix systems do not support dome camera communication protocol The most direct and easy way is to use current system to process video signal and add some control keyboards to control speed dome 19 Matrix or multiple image Processor Keyboard Figure 15 Keyboard connection 2 20 5 Installation 5 1 Surface Dome Installation Step 1 Draw a location hole 84 Bring the bracket anchor out from the package Draw four holes in the wall in accordance with the four holes of bracket anchor Step 2 Make holes and screw expansion bolt AY Make four holes and screw in four M8 EQ el expansion bolts A AN 3 2 LSA Note Expansion bolts are not included in the 70 Q M accessory package ie E Step 3 Loose bolts on both sides 2 M4X6 Stainless bolts P aum uu Take the dome out of the package open the transparent cover by loosing 2 M 4 6 stainless bolts Note Be careful pay attention to the transparent cover Step 4 Remove transparent cover Remove transparent cover from the dome Note Be careful pay attention to the transparent cover 21 Step 5 Take out pads Take out the two protect pads Note Be careful Pay attention

Q-See QSHI3512 Technical Manual

Contents

Download Pdf Manuals

Related Search

Related Contents