Home

Q-Logic 59021-05 B User's Manual

Contents

1. eo ke eo eo eo K i eo a TT Left Power RightPower Switch Switch Figure 2 2 Chassis Controls and LEDS 2 1 1 Power Switches Each power supply has an On Off switch that controls power to the switch logic circuitry To apply power to the switch place both switches in the On position 2 1 2 Maintenance Button The Maintenance button is a momentan switch on the front panel Its purpose is to place the switch in maintenance mode Maintenance mode sets the IP address to 10 0 0 1 and provides access to the switch for maintenance purposes when flash memory or the resident configuration file is corrupted Refer to Recovering a Switch on page 5 12 for information about maintenance mode To place the switch in maintenance mode do the following 1 Isolate the switch from the fabric Open a Telnet session and enter the Shutdown command Refer to Shutdown Command on page B 62 Place both power supply switches in the Off position 3 Press and hold the Maintenance button with a pointed tool for a few seconds then place one of the power supply switches in the On position You can release the Maintenance button after the Input Power LED illuminates When the switch is in maintenance mode the Heartbeat LED illuminates continuously Refer to Chassis LEDs on page 2 3 for
2. Figure 2 7 Ethernet Port 2 4 Serial Port The SANbox2 16 switch is equipped with an RS 232 serial port for maintenance purposes The serial port is located on the back of the switch under a small cover as shown in Figure 2 8 You can manage the switch through the serial port using the CLI Serial Port Figure 2 8 Serial Port 2 8 59021 05 B Power Supplies d tt 2 General Description Simplify OT WE The serial port connector requires a null modem F F DB9 cable The pins on the switch RS 232 connector are shown in Figure 2 8 and identified in Table 2 1 Refer to Connect the Management Workstation to the Switch on page 4 8 for information about connecting the management workstation through the serial port Table 2 1 Serial Port Pin Identification Pin Number Description Carrier Detect DCD Receive Data RxD Transmit Data TxD Data Terminal Ready DTR Signal Ground GND Data Set Ready DSR Request to Send RTS Clear to Send CTS oO D N O Ud bh W N Ring Indicator RI 2 5 Power Supplies The power supplies convert standard 110 or 230 VAC to DC voltages for the various switch circuits Each power supply has an AC power receptacle an On Off switch and two status LEDs as shown in Figure 2 9 After connecting a power supply to an AC voltage source and placing the power switch in the On position the power supply is energized and DC voltage is de
3. 59021 05 B B 23 B Command Line Interface d tt Set Command Simplify BE o 6 6 lt lt 7 7 lt lt Set Command Authority Syntax Keywords B 24 Sets a variety of switch parameters Admin for all keywords except Alarm Clear Beacon and Pagebreak which are available with User authority set alarm clear beacon state config option log option pagebreak state port option setup option switch state alarm clear Clears the alarm log This keyword is available with User authority beacon state Enables or disables the flashing of the Logged In LEDs according to state This keyword is available with User authority state can be one of the following on Enables the flashing beacon off Disables the flashing beacon config option Sets switch port alarm threshold and zoning configuration parameters Refer to the Set Config Command on page B 26 log option Specifies the type of entries to be entered in the event log Refer to the Set Log Command on page B 34 pagebreak state Specifies how much information is displayed on the screen at a time according to the value given by state This keyword is available with User authority state can be one of the following on Limits the display of information to 20 lines at a time The page break functions affects the following commands Alias List Members Show Alarm Log Zone List Members
4. 59021 05 B B 27 B Command Line Interface d tt Set Config Command Simplify ee switch Initiates an editing session in which to change switch configuration settings The system displays each parameter one line at a time and prompts you for a value For each parameter enter a new value or press the Enter key to accept the current value shown in brackets Table B 8 Set Config Switch Parameters Parameter Description AdminState Switch administrative state online offline or diagnostics BroadcastEnabled Enables True or disables False forwarding of broadcast frames InbandEnabled Enables True or disables False the ability to manage the switch over an ISL DefaultDomainiD Default domain ID setting Domain IDLock Prevents True or allows False dynamic reassignment of the domain ID SymbolicName Descriptive name R_T_TOV Receiver Transmitter Timeout Value Specifies the number of milliseconds a port is to wait to receive a response from another port The default is 100 R_A_TOV Resource Allocation Timeout Value The number of milliseconds the switch waits to allow two ports to allocate enough resources to establish a link The default is 10000 E D TOM Error Detect Timeout Value The number of milliseconds a port is to wait for errors to clear The default is 2000 FS_TOV Fabric Stability Timeout Value The default is 5000 msec DS_TOV Distributed Services Timeout Value Management Server Nam
5. Simplify Set Config Command d tt B Command Line Interface ZZZ A Table B 7 Set Config Port Parameters Continued Parameter Description DeviceScanEnabled Enables True or disables False the scanning of the connected device for FC 4 descriptor information during login The default is True ForceOfflineRSCN Enables False or disables True the immediate transmission of RSCN messages when communication between a port and its device is interrupted If enabled the RSCN message is queued for 200 ms The default is False This parameter is ignored if IOStreamGuard is enabled ARB_FF Use ARB_FF instead of idles on loop FCAL option InteropCredit Interoperability credit The number of buffer to buffer credits per port 0 means the default 12 is unchanged ExtCredit Extended credits The number of port buffer credits that this port can acquire from donor ports FANEnable Fabric address notification Enables True or disables False the communication of the FL_Port address port name and node name to the logged in NL_Port LCFEnable Link control frame preference R_CTL 0xC MFS_TOV MFS limit for camp on MFSEnable Multi Frame Sequence bundling MSEnable Management Server enable on this port NoClose Don t close unless another device arbitrates IOStreamGuard Enables or disables the suppression of RSCN messages VIEnable Enable VI preference routing CheckAlps Close before sending frames to new target
6. User defined name associated with the file that contains user list data for the fabric Fan Fail LED An LED that indicates that a cooling fan in the switch is operating below standard FC PLDA Fibre Channel Private Loop Direct Attach Flash Memory Memory on the switch that contains the chassis control firmware Glossary 1 SANbox2 16 Fibre Channel Switch Installation Guide I QG Aoooo 2 2 i Frame Data unit consisting of a start of frame SOF delimiter header data payload CRC and an end of frame EOF delimiter FRU Field Replaceable Unit Heartbeat LED A chassis LED that indicates the status of the internal switch processor and the results of the Power On Self Test Initiator The device that initiates a data exchange with a target device In Order Delivery A feature that requires that frames be received in the same order in which they were sent Input Power LED A chassis LED that indicates that the switch logic circuitry is receiving proper DC voltages IP Internet Protocol LIP Loop Initialization Primitive sequence Logged In LED A port LED that indicates device login or loop initialization status Management Information Base A set of guidelines and definitions for the Fibre Channel functions Glossary 2 Management Workstation PC workstation that manages the fabric through the fabric management switch MIB Management Information Base MSEnable Determin
7. 6 3 Fans The fans are hot pluggable This means you can remove or install one of the fans while the switch is operating without disrupting service The fan is completely enclosed so there is no risk of injury from the fan blades The fans are also interchangeable that is the left and right fans are the same unit To remove a fan loosen the two retaining screws then grasp the fan housing and pull firmly to disengage the modular connector Slide the fan out of its bay as shown in Figure 6 2 Figure 6 3 Fan Removal When replacing a fan consider the following MB The left and right fans are interchangeable However you must orient the fan so that the modular connector aligns with the mating connector in the switch as shown in Figure 6 4 a Replacement fans must be compatible with the switch air flow direction Air flow direction for switch model SB2A 16A is front to back air flow direction for switch model SB2A 16B is back to front wi A label on the fan indicates the switch model number and fan air flow direction as shown in Figure 6 4 CAUTION Both fans must have the same air flow direction to prevent the switch from overheating 6 4 59021 05 B d tt 6 Removal Replacement Simplify Fans To install a fan do the following 1 Confirm that the new fan is compatible with the switch air flow direction 2 Align the modular connector toward the inside of the switch as shown in Figure 6 4 3
8. Simplify Test Command ls 3 A series of test parameters are displayed on the screen Press the Enter key to accept each default parameter value or type a new value for each parameter and press the Enter key The TestLength parameter is the number of frames sent the FrameSize 256 byte maximum in some cases parameter is the number of bytes in each frame and the DataPattern parameter is the pattern in the payload Before running the test make sure that the device attached to the port can handle the test parameters SANbox2 admin gt test x online A list of attributes with formatting and current values will follow Enter a new value or simply press the ENTER key to accept the default value If you wish to terminate this process before reaching the end of the list press q or Q and the ENTER key to do so TestLength decimal value 1 4294967295 100 FrameSize decimal value 36 2148 256 DataPattern 32 bit hex value or Default Default StopOnError True False False Do you want to start the online test y n n 4 After all parameter values are defined type Y and press Enter to start the test 59021 05 B B 65 Uptime Command Simplify B Command Line Interface d tt U ooo Bo o 22 Uptime Command Displays the elapsed time since the switch was last reset and reset method Authority User Syntax uptime Examples The following is an example of the Uptime
9. zoning active cancel clear edit history limits list restore save active Displays membership information for the active zone set including member zones and zone members cancel Closes the current Zoning Edit session Any unsaved changes are lost clear Clears all inactive zone sets from the volatile edit copy of the zoning database This keyword does not affect the non volatile zoning database However if you enter the Zoning Clear command followed by the Zoning Save command the non volatile zoning database will be cleared from the switch Note The preferred method for clearing the zoning database from the switch is the Reset Zoning command edit Opens a Zoning Edit session history Displays a history of zoning modifications including the following Time of the most recent zone set activation or deactivation and the user who performed it m Time of the most recent modifications to the zoning database and the user who made them Checksum for the zoning database B 77 Zoning Command Simplify B Command Line Interface d tt U op o 22 limits Displays the maximum limits imposed on the zoning database for the number of zone sets zones aliases members per zone members per alias and total members list Lists all fabric zoning definitions This keyword is available with User authority restore Reverts the changes to the zoning database that have been made during the current Zoning Edit session
10. 1 1000 100 FallingTrigger decimal value 0 1000 5 SampleWindow decimal value 1 1000 sec TO Finished configuring attributes This configuration must be saved see config save command config activate command before it can take effect use the config cancel command and activated see To discard this configuration 59021 05 B d tt B Command Line Interface Simplify Set Config Command TY The following is an example of the Set Config Zoning command SANbox2 gt admin start SANbox2 admin gt config edit SANbox2 admin config gt set config zoning A list of attributes with formatting and current values will follow Enter a new value or simply press the ENTER key to accept the current value If you wish to terminate this process before reaching the end of the list press q or Q and the ENTER key to do so AutoSave True False True Default All None All Finished configuring attributes This configuration must be saved see config save command and activated see config activate command before it can take effect To discard this configuration use the config cancel command 59021 05 B B 33 B Command Line Interface fog Set Log Command q ee Set Log Command Authority Syntax Keywords B 34 Specifies the type of entries to be entered in the event log The log is a storage file contained on the switch The log can hold a maximum of 200 entries When
11. 12 buffer credits per port Media Type ee Small Form Pluggable SFP optical transceivers Hot swappable 3 3 Volts Fabric Port Speed 1 0625 or 2 125 Gigabits second Maximum Frame Size 2148 bytes 2112 byte payload System Processor 266 MHz Pentium processor Fabric Latency best case lt 0 4 usec Fabric Point to Point Bandwidth 212 or 424 MB s full duplex Fabric Aggregate Bandwidth 64 Gb s for a single switch A 2 Switch Maintainability Maintenance Strategy Field Replaceable Units SFP transceivers Power supplies Fans Diagnostics eee eene terrere Power On Self Test POST tests all functional components except SFP transceivers User Interface LED indicators A 2 59021 05 B A Specifications Fabric Management SE A 3 Fabric Management A 4 Management Methods Maintenance Connection Ethernet Connection Switch Agent Switch Dimensions A 5 Switch Electrical Power source loading Heat Output maximum Operating voltage Circuit Protection SANbox Manager application Command Line Interface GS 3 Management Server SNMP FTP RS 232 connector null modem F F DB9 cable RJ 45 connector 10 100BASE T cable
12. 19 6 Kb 59021 05 B B 49 Show Command Simplify B Command Line Interface d tt ooo oo The following is an example of the Show Port command SANbox2 gt show port 1 Port Number 1 AdminState Online PortID 640100 AsicNumber D PortWWN AsicPort 1 RunningType Donor ConfigType Donor SFPPartNumber PL XPL 00 S23 00 DiagStatus Passed SFPRevision EpConnState None SFPType 100 M5 SN I EpIsoReason NotApplicable SFPVendor PICOLIGHT LinkSpeed 2Gb s SFPVendorID 00850400 LinkState Active SymbolicName Portl LoginStatus LoggedIn SyncStatus SyncLost MaxCredit 0 XmitterEnabled False OperationalState Online ALInit 0 FlowErrors 0 PrimSeqErrors 0 ALInitError 0 FReject 0 RxLinkResets 0 Class2FramesIn 0 InvalidCRC 0 RxOfflineSeq 0 Class2FramesOut 0 InvalidDestAddr 0 TotalErrors 0 Class2WordsIn 0 LIP_AL PD AL PS 0 TotalLIPsRecvd 0 Class2WordsOut 0 LIP_F7_AL PS 0 TotalLinkResets 0 Class3FramesIn 0 LIP_F7_F7 0 TotalOfflineSeq 0 Class3FramesOut 0 LIP_F8_AL PS 0 TotalRxFrames 0 Class3Toss 0 LIP_F8_F7 0 TotalRxWords 0 Class3WordsIn 0 LinkFailures 0 TotalTxFrames 0 Class3WordsOut 0 Login 0 TotalTxWords 0 DecodeErrors 0 Logout 0 TxLinkResets 0 EpConnects 0 LoopTimeouts 0 TxOfflineSeq 0 FBusy 0 LossOfSync 0 TxWaits 0 B 50 59021 05 B Simplify Show Command d tt B Command Line Interface SE The following is an example of the Show Switch command SANbox2 gt show switch Switch Informatio
13. Allows a network management station to obtain configuration values traffic information and failure data pertaining to the Fibre Channels via SNMP through the Ethernet interface 17 0 19 inch rack mount 1 75 18 0 18 Ibs 1 9 Amps maximum at 90 to 137 Vac 0 95 Amps maximum at 180 to 265 Vac 170 watts 90 to 137 Vac 47 to 63 Hz 180 to 265 Vac 47 to 63 Hz Internally fused 59021 05 B A Specifications Switch Environmental ee A 6 Switch Environmental Temperature M Operating m Non operating Humidity M Operating m Non operating Altitude M Operating m Non operating Vibration M Operating m Non operating Shock M Operating m Non operating eeeeeee Air How A 7 Switch Regulatory Certifications Safety Standards Emissions Standards Voltage Fluctuations Harmonics sf ele EE Mark 00 tii A 4 10 to 40 C 50 to 104 F 40 to 65 C 40 to 149 F 25 to 80 non condensing 25 to 90 non condensing 0 to 3048m 0 to 10 000 feet 0 to 15 240m 0 to 50 000 feet Magnitude during after along any axis 2 54 mm 1 5 14 Hz 0 1G 14 300 Hz 5 500 Hz random 2 09 G rms 10 minutes Magnitude during aft
14. If you connect a new switch to an existing fabric with its domain ID unlocked and a domain ID conflict occurs the new switch will isolate as a separate fabric However you can remedy this by resetting the new switch or taking it offline then back online The principal switch will reassign the domain ID and the switch will join the fabric Note Domain ID reassignment is not reflected in zoning that is defined by domain ID port number pair or Fibre Channel address You must reconfigure zones that are affected by domain ID reassignment To prevent zoning definitions from becoming invalid under these conditions lock the domain IDs using SANbox Manager or the Set Config Switch command 3 2 59021 05 B Multiple Chassis Fabrics SE df 3 Planning 3 2 2 Common Topologies This section describes three commonly used topologies NW Cascade H Mesh H Multistage 3 2 2 1 Cascade Topology A cascade topology describes a fabric in which the switches are connected in a linear fashion If you connect the last switch back to the first switch you create a cascade with a loop topology as shown in Figure 3 1 The loop reduces latency because any switch can route traffic in the shortest direction to any switch in the loop The loop also provides failover should a switch fail The cascade fabric shown in Figure 3 1 has the following characteristics m Each chassis link contributes up to 200 MB s of bandwidth between chassis 400 MB s in full
15. This section describes the removal and replacement procedures for the following field replaceable units FRU a SFP transceivers n Power supplies a Fans The switch is equipped with a battery that powers the non volatile memory This memory stores the switch configuration The battery is not a field replaceable unit WARNING Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of the used battery according to the manufacturer s instructions WARNUNG Bei unsachgem ausgetauschter Batterie besteht Explosionsgefahr Die Batterie nur mit der gleichen Batterie oder mit einem quivalenten vom Hersteller empfohlenen Batterietyp ersetzen Die gebrauchte Batterie gem den Herstelleranweisungen entsorgen AVERTISSEMENT Danger d explosion si le remplacement de la pile est incorrect Ne remplacer que par une pile de type identique ou quivalent recommand par le fabricant Jeter la pile usag e en observant les instructions du fabricant 6 1 6 Removal Replacement d tt SFP Transceivers Simplify E q ooo 6 1 SFP Transceivers The SFP transceivers can be removed and replaced while the switch is operating without damaging the switch or the transceiver However transmission on the affected port will be interrupted until the transceiver installed To remove a transceiver gently press the transceiver into the port to re
16. members alias Displays all members of the alias given by alias This keyword is available with User authority and does not require a zoning edit session or an admin session remove alias members Removes the ports devices given by members from the alias given by alias members can have one of the following formats a Domain ID and port number pair Domain ID Port Number Domain IDs and port numbers are in decimal Ports are numbered beginning with 0 m 6 character hexadecimal device Fibre Channel address hex m 16 character hexadecimal worldwide port name WWPN for the device with the format xX XX XX XX XX XX XX XX rename alias_old alias_new Renames the alias given by alias_old to the alias given by alias_ new B 6 59021 05 B B Command Line Interface Config Command SE Config Command Authority Syntax Keywords 59021 05 B Manages the Fibre Channel configurations on a switch For information about setting the port and switch configurations refer to the Set Config Command on page B 26 Admin for all keywords except List config activate config backup cancel copy config_source config_destination delete config edit config list restore save config activate config Activates the configuration given by config If you omit the configuration the currently active configuration is used Only one configuration can be active ata time backup Creates a file named conf
17. 0 0 0 0 0 136M 58 0 0 0 0 A 36M q 59021 05 B B 59 Show Setup Command Simplify B Command Line Interface d tt ee Show Setup Command Displays the current SNMP and system settings Authority User Syntax show setup mfg snmp system Keywords mfg Displays manufacturing information about the switch snmp Displays the current SNMP settings system Displays the current system settings Examples The following is an example of the Show Setup Mfg command SANbox2 gt show setup mfg Manufacturing Information BrandName QLogic BuildDate Unknown ChassisPartNumber Unknown ChassisSerialNumber 0 CPUBoardSerialNumber 000603949 MACAddress 00 c0 dd 00 90 aa PlanarPartNumber Unknown SwitchSymbolicName SANbox2 SwitchWWN 10 00 00 c0 dd 00 90 ab SystemDescription QLogic SANbox2 FC Switch SystemObjectID TI 141 L66841 dd bel The following is an example of the Show Setup Snmp command SANbox2 gt show setup snmp SNMP Information Contact lt sysContact undefined gt Location N_107 System Test Lab Description QLogic SANbox2 FC Switch TraplAddress 10 0 0 254 TraplPort 162 TraplSeverity warning TraplVersion 2 TraplEnabled False B 60 59021 05 B Simplify Show Setup Command d tt B Command Line Interface ZZZ A Trap2Address 0 0 0 0 Trap2Port 162 Trap2Severity warning Trap2Version 2 Trap2Enabled False Trap3Address 0 0 0 0 Trap3Port 162 Trap3Severity warning Trap3Version 2 Trap3Enable
18. 37 d9 4f 46 The following is an example of the Show NS Domain_ID command SANbox2 32 gt show ns 102 Seg Domain Port Port No ID ID Type COS PortWWN NodeWWN 1 102 0x66 6606dc NL 3 21 00 002202 37 L92 TE 7C 207002003 20337 31921t 310 2 102 0x66 6606e0 NL 3 21 00 00 20 37 19 1d c8 20 00 00 20 37 19 1d c8 3 102 0x66 6606el NL 3 21 00 00 20 37 19 1d 33 20 00 00 20 37 19 1d 33 4 102 0x66 6606e2 NL 3 213 00 00320737319 E 93 2000200720337 195 L E 93 5 102 0x66 6606e4 NL 3 21 00 00 20 37 19 1f a5 20 00 00 20 37 19 1f a5 6 102 0x66 6606e8 NL 3 21 00 00 20 37 19 1d 9b 20 00 00 20 37 19 1d 9b Si 102 0x66 6606ef NL 3 21 00 00 20 37 19 1 90 20 00 00 20 37 19 1 90 The following is an example of the Show Interface command SANbox2 gt show interface eth0 Link encap Ethernet HWaddr 00 C0 DD 00 BD ED inet addrs 10 20 68 107 Boast 10 20 689 255 Mask 255 255 255 0 UP BROADCAST RUNNING MULTICAST MTU 1500 Metric l RX packets 4712 errors 0 dropped 0 overruns 0 frame 0 TX packets 3000 errors 0 dropped 0 overruns 0 carrier 0 collisions 0 txqueuelen 100 RX bytes 415313 405 5 Kb TX bytes 716751 699 9 Kb Interrupt 11 Base address 0xfcc0 lo Link encap Local Loopback inet addr 127 0 0 1 Mask 255 0 0 0 UP LOOPBACK RUNNING MTU 16436 Metric 1 RX packets 304 errors 0 dropped 0 overruns 0 frame 0 TX packets 304 errors 0 dropped 0 overruns 0 carrier 0 collisions 0 txqueuelen 0 RX bytes 20116 19 6 Kb TX bytes 20116
19. 59021 05 B 3 Planning Performance lia 3 3 2 Bandwidth 3 3 3 Latency 59021 05 B Bandwidth is a measure of the volume of data that can be transmitted at a given transmission rate A port can transmit or receive at 1 Gbps or 2 Gbps depending on the device to which it is connected The switch supports all transmission rate combinations as shown in Table 3 1 Table 3 1 Port to Port Transmission Combinations Source Port Rate Destination Port Rate Maximum Bandwdith 1 Gbps 1 Gbps 1 Gbps x 2 ports 2 Gbps 2 Gbps 1 Gbps 2 Gbps 2 Gbps 1 Gbps x 2 ports 2 Gbps 100 MB 100 MB 200 MB 100 MB each port 200 MB Bandwidth will be less for larger sequence sizes In multiple chassis fabrics each link between chassis contributes 100 or 200 megabytes of bandwidth between those chassis When additional bandwidth is needed between devices increase the number of links between the connecting switches The switch guarantees in order delivery with any number of links between chassis Latency is a measure of how fast a frame travels from one port to another The factors that affect latency include transmission rate and the source destination port relationship as shown in Table 3 2 Table 3 2 Port to Port Latency Source Destination Rates Same Switch 1 Gbps 1 Gbps 2 Gbps 2 Gbps lt 1 usec lt 0 4 usec 3 7 Device Access 3 Planning df RN 3
20. IP address 4 Enter the following account name and password user images password images 5 Activate binary mode and copy the firmware image file on the switch ftp gt bin ftp gt put filename 6 Close the FTP session ftp gt quit 7 Establish communications with the switch using the CLI Enter one of the following on the command line telnet XXX XXX XXX XXX or telnet switchname where xxx xxx xxx xxx is the switch IP address and switchname is the switch name associated with the IP address 8 A Telnet window opens prompting you for a login Enter an account name and password The default account name and password are admin password 9 Open an Admin session to acquire the necessary authority cli gt admin start 59021 05 B 4 19 Powering Down a Switch U ooo Poo 4 Installation gi q Simplify 10 Display the list of firmware image files on the switch to confirm that the file was loaded Refer to the Image Command on page B 13 for more information cli admin gt image list 11 Unpack the firmware image file to install the new firmware in flash memory cli admin gt image unpack filename 12 Reset the switch to activate the new firmware This will close the Telnet session by default cli admin gt reset 4 4 Powering Down a Switch Simply unplugging the switch from the power source does not allow the switch to complete executing tasks and could lead to flash memory corru
21. Link Resets issued by this port TxOfflineSeq Total number of Offline Sequences issued by this port TxWait Time waiting to transmit when blocked with no credit Measured in FC Word times post log Displays the Power On Self Test POST log containing the results from the POST setup option Displays setup attributes for the system SNMP and the switch manufacturer Refer to the Show Setup Command on page B 60 steering domain_id Displays the routes that data takes to the switch given by domain_id If you omit domain_id the system displays routes for all switches in the fabric support Executes a series of commands that display a complete description of the switch its configuration and operation The display can be captured from the screen and used for diagnosing problems This keyword is intended for use at the request of your authorized maintenance provider The commands that are executed include the following H Date Alias List Config List Date History Ps Show About Alarm Backtrace Chassis Config Port Config Switch Config Threshold Dev Dev Settings Domains Donor Fabric Log Log Settings Lsdb Mem Ns Perf Port Setup Mfg Setup Snmp Setup System Steering Switch Topology Users Uptime User Accounts Whoami Zoneset Active List Zoning History Limits List 59021 05 B B 47 Show Command Simplify B Command Line Interface d tt U ooo o o A switch Displays swi
22. SANbox Switch Software page scroll to the SANbox2 2Gb Series area In the Windows column choose the SANbox Manager link to open the File Download window You have a choice of running the installation file from the CD ROM or downloading the installation file to your hard drive Choose one of the following m Open the installation file from the CD ROM and follow the SANbox Manager installation instructions m Specify a location in which to save the sansurfer_windows_install exe file and choose the Save button Double click the saved sansurfer_windows_install exe file and follow the SANbox Manager installation instructions 4 Installation Installing a Switch E ee 4 2 7 SANsurfer Management Suite Disk Linux Installation To install the SANbox Manager application on Linux from the SANsurfer Management Suite Disk do the following 1 4 12 Close all programs currently running and insert the SANsurfer Management Suite Disk into the management workstation CD ROM drive If a file browser window opens showing icons for the contents of the CD ROM double click the Start_Here htm file to open the SANsurfer Management Suite start page If a file browser does not open double click the CD ROM icon on the to open the browser If there is no CD ROM icon do the following a Open an xterm or other terminal window b Mount the CD ROM From a shell prompt enter the following command mount mnt cdrom c Execute you
23. Slide the fan into the bay until it is firmly seated and confirm that the air flow is correct Fasten the screws Modular Connector Figure 6 4 Fan Installation for Switch Model SB2A 16B 59021 05 B 6 5 Fans Simplify 6 Removal Replacement d tt OOOO ES oo Notes 6 6 59021 05 B Appendix A Specifications Appendix A contains the specifications for the SANbox2 16 Fibre Channel switch Refer to Section 2 General Description for the location of all connections switches controls and components A7 Switch Specifications Fibre Channel Protocols Fibre Channel Classes of Service Modes of Operation Port Types Port Characteristics Number of Fibre Channel Ports A 59021 05 B FC PH Rev 4 3 FC PH 2 FC PH 3 FC AL Rev 4 5 FC AL 2 Rev 7 0 FC FLA FC GS 3 FC FG FC PLDA FC Tape FC VI FC SW 2 Fibre Channel Element MIB RFC 2837 Fibre Alliance MIB Version 3 0 Classes 2 and 3 Fibre Channel Classes 2 and 3 connectionless F_Port FL_Port TL_Port E Port G Port GL_Port All ports are auto discovering and self configuring 16 ports per chassis Maximum 239 switches depending on configuration A Specifications d tt Simplify Switch Maintainability ee Maximum User Ports gt 475 000 ports depending on configuration Buffer Credits
24. a loss of synchronization for a period of time greater than the value of R_T_TOV or by loss of signal while not in the offline state A loss of signal causes the switch to attempt to re establish the link If the link is not re established by the time specified by R_T_TOV a link failure is counted A link reset is performed after a link failure Time when the port logged in Time when port logged out A two 2 second timeout as specified by FC AL 2 Number of synchronization losses gt 100 ms detected by this port A loss of synchronization is detected by receipt of an invalid transmission word Primitive sequence errors detected Number of link reset primitives received from an attached device Number of offline sequences received An OLS is issued for link initialization a Receive amp Recognize Not_Operational NOS state or to enter the offline state Total number of errors detected Number of loop initialization primitive frames received by this port Total number of link reset primatives Total number of Offline Sequences issued by this port Total number of frames received by this port Total number of words received by this port Total number of frames issued by this port Total number of words issued by this port B 46 59021 05 B d tt B Command Line Interface Simplify Show Command SE Table B 13 Show Port Parameters Continued Entry Description TxLinkResets Number of
25. according to your platform m For Windows a Open the HyperTerminal application on a Windows platform Choose the Start button select Programs Accessories HyperTerminal and HyperTerminal b Enter a name for the switch connection and choose an icon in the Connection Description window Choose the OK button c Select the COM port in the Connect To window and choose the OK button d Enter the following COM Port settings in the COM Properties window and choose the OK button O Bits per second 9600 Data Bits 8 Parity None Stop Bits 1 Flow Control None Oooo 59021 05 B 4 9 Installing a Switch 4 Installation d tt Simplify SES H For Linux a Setup minicom to use the serial port Create or modify the letc minirc dfl file with the following content pr portdev ttyS0 pu minit pu mreset pu mhangup b Verify that all users have permission to run minicom Review the letc minicom users file and confirm that the line ALL exists or that there are specific user entries C Enter the following command at the Linux prompt minicom u For Solaris a Setup Solaris to use the serial port Modify the etc remote file to include the following lines sanbox2 dv dev term a br 9600 el C S 0 U D ie 0e D b Enter the following command at the Solaris prompt tip sanbox2 3 Log in to the switch The default account name and password are admin password SANbox2 Login admin Pass
26. cable must be rated at 10 Amps meet the requirements of HO5VV F and be approved by VDE SEMKO and DEMKO AVERTISSEMENT Pour la s curit de Putilisateur l appareil est livr avec un c ble d alimentation trifilaire et une fiche Pour viter toute secousse lectrique enficher ce c ble une prise correctement mise la terre Une prise lectrique dont les fils sont mal branch s peut cr er une tension dangereuse dans les pi ces m talliques du ch ssis switch Pour viter toute secousse lectrique s assurer que les fils sont correctement branch s et que la prise est bien mise la terre Dans certains pays les prises lectriques sont de mod le different on ne peut y enficher le c ble de l appareil On doit donc en utiliser un autre ayant les caract ristiques suivantes m Alimentation 125 V C ble pour courant nominal de 10 A agr LAC et CSA m Alimentation 250 V C ble pour courant nominal de 10 A conforme au HO5VV F et agr VDE SEMKO et DEMKO 59021 05 B 4 5 4 Installation gi q Simplify Installing a Switch U xF q Oo I lt lt lt lt WARNUNG Dieses Produkt wird mit einem 3 adrigen Netzkabel mit Stecker geliefert Dieses Kabel erf llt die Sicherheitsanforderungen und sollte an einer vorschriftsm igen Schukosteckdose angeschlossen werden um die Gefahr eines elektrischen Schlages zu vermeiden Elektrosteckdosen die nicht richtig verdrahtet sind k nnen gef hr
27. command SANbox2 admin gt user add H Press q and the ENTER key to abort this command account name 1 15 chars user3 account password 4 20 chars please confirm account password should this account have admin authority y n n y OK to add user account user3 with admin authority Please confirm y n n y The following is an example of the User Delete command SANbox2 admin gt user del user3 The user account will be deleted Please confirm y n n y The following is an example of the User List command SANbox2 admin gt user list Current list of users logged in snmp OB sessionl logged in since Mon Apr 21 09 20 38 2003 snmp IB session2 logged in since Mon Apr 21 09 20 38 2003 admin IB session3 logged in since Mon Apr 21 09 20 56 2003 admin IB session4 logged in since Mon Apr 21 09 20 56 2003 admin OB session5 logged in since Mon Apr 21 09 33 52 2003 admin OB session10 logged in since Mon Apr 21 10 11 36 2003 in admin mode admin oB sessionll logged in since Mon Apr 21 11 01 09 2003 admin IB sessionl2 logged in since Mon Apr 21 11 42 11 2003 admin OB sessionl4 logged in since Mon Apr 21 13 09 19 2003 root OB session15 logged in since Mon Apr 21 13 20 03 2003 B 68 59021 05 B Simplify Whoami Command d tt B Command Line Interface SE Whoami Command Displays the account name session number and switch domain ID for the Telnet session Authority User
28. configuration edit session in the configuration given by config If you omit the configuration name value the configuration you chose for the Config Edit command is used The switch supports up to 10 configurations including the default configuration If you edit the active configuration changes will be held in suspense until you reactivate the configuration or activate another configuration The following shows an example of how to open and close a Config Edit session SANbox2 gt admin start SANbox2 admin gt config edit SANbox2 admin config gt config cancel Configuration mode will be canceled Please confirm y n n y SANbox2 admin gt admin end 59021 05 B d tt B Command Line Interface Simplify Date Command Date Command This command displays or sets the system date and time To set the date and time the information string must be provided in this format MMDDhhmmCCYY The new date and time takes effect immediately Authority Admin to change the date User to display the date Syntax date MMDDhhmmCCYY Keywords MMDDhhmmCCYY Specifies the date this requires an admin session If you omit MMDDhhmmCCYY the current date is displayed this is available with User authority Examples The following is an example of the Date command SANbox2 gt date Mon Apr 07 07 51 24 2003 59021 05 B B 9 Fallback Command B Command Line Interface d tt Simplify E oe Fall
29. duplex However because of the sequential structure that bandwidth will be shared by traffic between devices on other chassis m Latency between any two ports is no more than three chassis hops m 48 Fibre Channel ports are available for devices NU NUS RS CCAA RO O a NAO o i N LERNT Ja Figure 3 1 Cascade with a Loop Topology 59021 05 B 3 3 3 Planning dt Multiple Chassis Fabrics ee 3 2 2 2 Mesh Topology A mesh topology describes a fabric in which each chassis has at least one port directly connected to each other chassis in the fabric The example mesh fabric shown in Figure 3 2 has the following characteristics u Each link contributes up to 200 MB s of bandwidth between switches 400 MB s in full duplex Because of multiple parallel paths ther
30. hat 4 3 6 4 1 5 Notes informatives relatives a la s curit Une note informative Avertissement indique la presence d un risque pouvant entrainer des blessures 4 3 4 5 6 1 Une note informative Attention indique la pr amp sence d un risque pouvant entrainer des deg ts materiels 4 3 6 4 59021 05 B 1 3 Communications Statements 1 Introduction dog q Simplify SES 1 6 Communications Statements The following statements apply to this product The statements for other products intended for use with this product appear in their accompanying manuals 1 6 1 Federal Communications Commission FCC Class A Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area may cause unacceptable interference in which case the user will be required to correct the interference at their own expense Neither the provider nor the manufacturer is responsible for any radio or television interference caused by unauthorized changes or modifications to this
31. information about the Input Power LED and the Heartbeat LED To return to normal operation power cycle the switch 2 2 59021 05 B gi 2 General Description g Simplify Chassis Controls and LEDs SE 2 1 3 Chassis LEDs The chassis LEDs shown in Figure 2 3 provide status information about switch operation Refer to Power Supplies on page 2 9 for information about power supply LEDs and to Port LEDs on page 2 5 for information about port LEDs Over Temperature LED Fan Fail LED Heartbeat LED Input Power LED Amber Amber Amber Green Figure 2 3 Chassis LEDs 2 1 3 1 Over Temperature LED Amber The Over Temperature LED provides status information about the air temperature inside the switch This LED illuminates to indicate that the switch logic circuitry is overheating Refer to Section 5 Diagnostics Troubleshooting for information about troubleshooting over temperature conditions 2 1 3 2 Fan Fail LED Amber The Fan Fail LED indicates operational status of both fans This LED illuminates if the speed of either fan falls below the normal range Removing a fan will not illuminate the Fan Fail LED Refer to Section 5 Diagnostics Troubleshooting for information about troubleshooting fan failure conditions 59021 05 B 2 3 2 General Description dog Fibre Channel Ports q Simplify U ooo 2 2 1 3 3 Heartbeat LED Amber The Heartbeat LED indicates the status of the internal switch process
32. installation instructions Enter the following command pkgadd d sol_pkg 59021 05 B 4 Installation Installing a Switch EE 4 2 12 Configure the Switch Do the following to configure a switch using the SANbox Manager application Refer to the SANbox2 8c 16 Switch Management User s Guide for more information about configuring a switch You can also configure the switch using the Command Line Interface Refer to Appendix B Command Line Interface for more information 1 Connect to the switch using an Ethernet connection and run SANbox Manager Open the Fabric menu and select Add Fabric to open the Add a New Fabric window Enter a fabric name and the IP address of the switch through which to manage the fabric The default IP address is 10 0 0 1 If this is a new switch leave the login name and password fields empty and choose the Add Fabric button By default fabric security is disabled and therefore account names and passwords are not enforced Refer to the Set Setup Command on page B 38 for information about setting fabric security Open the Switch menu and select Switch Properties In the Switch Properties window enter a chassis name Accept the default domain ID and choose the OK button Open the Switch menu and select Network Properties In the Network Properties window enter values for the IP address subnet mask and gateway address Accept the default boot method If you know the SNMP configuration sett
33. support qlogic com Technical Training tech training qlogic com Switch Support Web Site support qlogic com 59021 05 B 1 9 1 Introduction da q Simplify Technical Support SE Notes 59021 05 B Section 2 General Description This section describes the features and capabilities of the SANbox2 16 Fibre Channel switch The following topics are described Chassis controls and LEDs Fibre channel ports Ethernet port Serial port Power supplies Fans Switch management Fabrics are managed with the SANbox Manager switch management application version 1 05 and the Command Line Interface CLI Refer to the SANbox2 8c 16 Switch Management User s Guide for information about using the SANbox Manager application Refer to Appendix B Command Line Interface for more information 59021 05 B Figure 2 1 SANbox2 16 Fibre Channel Switch 2 1 2 General Description dog Chassis Controls and LEDs q Simplify 21 Chassis Controls and LEDs Chassis controls include the power supply On Off switches and the Maintenance button as shown in Figure 2 2 The chassis LEDs include the Over Temperature LED Fan Fail LED Heartbeat LED and the Input Power LED Chassis LEDs Maintenance Button o000 TE TE EE N D I E FE IPD 00 00 o 00 60 60 60
34. switch in maintenance mode Do the following a Power down the switch b Press and hold the Maintenance button with a pointed tool then power up the switch All chassis LEDs will illuminate then extinguish leaving only the Input Power LED illuminated Release the button 2 Allow one minute for the switch to complete its tests When the switch is in maintenance mode the Input LED will be illuminated and the Heartbeat LED will illuminate continuously All other chassis LEDs will be extinguished 3 Establish a Telnet session with the switch using the maintenance mode IP address 10 0 0 1 4 Enter the maintenance mode account name and password prom prom and press the Enter key Sanbox login prom Password xxxx username anteater Itasca telnet 10 0 0 1 Trying 10 0 0 1 Connected to 10 0 0 1 Escape character is 5 12 59021 05 B d tt 5 Diagnostics Troubleshooting Simplify Recovering a Switch SE 5 The maintenance menu displays several recovery options To select a switch recovery option press the corresponding number displayed in option field on the keyboard and press the Enter key Exit Image Unpack Reset Network Config Reset Password File Copy Log Files Remove Switch Config Remake Filesystem 7 Reset Switch Option On OG NO OH These options and their use are described in the following sections 5 3 1 Maintenance Exit This option closes the current
35. system configuration settings The switch maintains one SNMP configuration and one system configuration Authority Admin Syntax set setup snmp system Keywords snmp Prompts you in a line by line fashion to change SNMP configuration settings Table B 11 describes the SNMP fields For each parameter enter a new value or press the Enter key to accept the current value shown in brackets Table B 11 SNMP Configuration Settings Trap 1 5 Address Trap 1 5 Port Trap 1 5 Severity Trap 1 5 Version Trap 1 5 Enabled ReadCommunity WriteCommunity Entry Description Contact Specifies the name of the person to be contacted to respond to trap events The default is undefined Location Specifies the name of the switch location The default is undefined Specifies the workstation IP address to which SNMP traps are sent The default address for trap 1 is 10 0 0 254 The default address for traps 2 5 is 0 0 0 0 Specifies the workstation port to which SNMP traps are sent Specifies the severity level to use when monitoring trap events The default is Warning Specifies the SNMP version 1 or 2 to use in formatting traps The default is version 2 Specifies whether traps event information are enabled or disabled default Read community password that authorizes an SNMP agent to read information from the switch This is a write only field The value on the switch and the SNMP management server must
36. you wish to terminate this process before reaching the end of the list press q or Q and the ENTER key to do so EthONetworkDiscovery 1 Static 2 Bootp 3 Dhcp 4 Rarp Static EthONetworkAddress dot notated IP Address PELO sO 0 L EthONetworkMask dot notated IP Address 2552552550 Eth0GatewayAddress dot notated IP Address 10 0 0 254 AdminTimeout dec value 0 1440 minutes 0 never 30 TempMonitoringWarning dec value 0 100 degrees Celsius 65 TempMonitoringFailure dec value 0 100 degrees Celsius 70 TempFailurePortShutdown True False False SecurityEnabled True False False LocalLogEnabled True False True RemoteLogEnabled True False False RemoteLogHostAddress dot notated IP Address 10 0 0 254 B 42 59021 05 B d tt B Command Line Interface Simplify Show Command 13 Show Command Displays fabric switch and port operational information Authority User Syntax show about alarm broadcast chassis config option domains donor fabric interface log option Isdb mem count ns foption pagebreak perf option port port_number post log setup option steering domain_id support switch topology users version Keywords about Displays an introductory set of information about operational attributes of the switch This keyword is equivalent to the Version keyword alarm Displays the last 200 alarm entries broadcast Displays the broadcast tree information and all
37. 1 05 B maintainability A 2 maintenance blink pattern 5 2 exit 5 13 interface A 3 menu 5 13 mode 2 2 5 2 5 12 strategy A 2 Maintenance button 2 2 5 12 management workstation 2 8 4 8 manufacturer information B 60 marking A 4 media type A 2 memory activity B 44 flash 2 2 mesh topology 3 4 minicom 4 10 Multistage topology 3 5 N name server display B 44 zone 3 9 network configuration reset B 19 interfaces B 44 non fatal error 5 1 null modem F F DB9 cable 4 8 O online test B 63 Output Power LED 2 10 5 11 Over Temperature LED 2 3 chassis 2 3 5 10 power supply 2 10 5 11 P page break B 24 Passwd command B 15 password change B 15 Index 3 SANbox2 16 Fibre Channel Switch Installation Guide a ooo oe lt oi OOoBO C M file reset 5 14 maintenance mode 5 12 restore default 5 14 switch 3 11 B 15 user account B 1 performance 3 6 Ping command B 16 planning 3 1 port administrative state B 37 buffer credits 3 6 configuration 4 16 B 26 configuration display B 53 counters B 37 diagnostics 5 5 Ethernet 2 8 external test B 63 Fibre Channel 2 4 generic 2 6 initialize B 19 internal test B 63 LEDs 2 5 loopback test B 63 maximum number of ports users A 2 modes 2 6 online test B 63 operational information B 45 performance B 44 B 58 serial 2 8 speed A 2 B 37 POST See Power On Self Test power cords 4 2 down switch 4 20 requirements 4 1 source loading A 3
38. 13 5 nm Transmit Power 10 dBm minimum Receiver Sensitivity 20 dBm average DISTANCE TEE 2 meters to 10 kilometers A ei DHHS 21 CFR J IEC 825 1 CENELEC EN 60825 1 VDE Standard NEE Small Form Factor Pluggable Multisource Agreement A 6 59021 05 B Appendix B Command Line Interface Each switch contains a Telnet server This server allows a Telnet client to establish a Telnet session with the switch to retrieve information or to configure parameters using the Command Line Interface CLI The CLI enables you to perform a variety of fabric and switch management tasks through an Ethernet or a serial port connection B 1 Logging On to a Switch To log on to a switch using Telnet open a command line window on the management workstation and enter the Telnet command followed by the switch IP address gt telnet 123 45 67 89 A Telnet window opens prompting you for a login Enter an account name and password Switches come from the factory with the following user account already defined Account name admin Password password Authority Admin This user account provides full access to the switch and its configuration After planning your fabric management needs and creating your own user accounts consider changing the password for this account Refer to Commande on page B 3 for more information about authority levels Refer to the User Command on page B 67 for informati
39. 4 Device Access Consider device access needs within the fabric Access is controlled by the use of zones and zone sets Some zoning strategies include the following H Separate devices that use different operating systems NW Separate devices that have no need to communicate with other devices in the fabric or have classified data m Separate devices into department administrative or other functional group E Group TL_Port target devices with initiators to allow automatic discovery m Reserve a path and its bandwidth from one port to another A zone is anamed group of devices that can communicate with each other Membership in a zone can be defined by switch port number port Fibre Channel address or by device worldwide name WWN Devices can communicate only with devices that are members of the same zone A zone can be a member of more than one zone set Several zone sets can be defined for a fabric but only one zone set can be active at one time The active zone set determines the current fabric zoning A zoning database is maintained on each switch consisting of all inactive zone sets the active zone set all zones aliases and their membership The SANbox2 16 switch supports the following maximum limits m 256 zone sets 256 zones per zone set 1000 total zones 2000 members per zone 256 aliases 2000 members per alias 2000 total number of alias and zone members Three types of zones are supported E Softzone H Access C
40. 4 protocols A 1 field replaceable unit 6 1 File Transfer Protocol 4 19 5 3 firmware failure 5 2 fallback version B 10 image file B 13 install with CLI 4 18 install with FTP and CLI 4 19 install with SANbox Manager 4 17 list image files B 13 remove image files B 13 retrieve image file B 13 unpack image 5 13 B 13 version B 48 FL_Port 2 7 flash memory 2 2 4 20 frame size A 2 FRU See Field Replaceable Unit FTP See File Transfer Protocol G G_Port 2 7 GBIC See GigaBit Interface Converter generic ports 2 6 Gigabit Interface Converter 3 1 GL_Port 2 6 harmonics A 4 59021 05 B SANbox2 16 Fibre Channel Switch Installation Guide ls HBA See Host Bus Adapter Heartbeat LED 2 4 5 1 Help command B 11 History command B 12 host bus adapter 3 1 humidity 4 2 A 4 HyperTerminal application 4 9 Image command B 13 immunity A 4 Input Power LED 2 4 5 10 installation 4 2 internal firmware failure 5 2 test B 63 L laser specifications A 6 latency 3 7 A 2 LED Activity 2 6 Fan Fail 2 3 5 10 Heartbeat 2 4 5 1 Input Power 2 4 5 10 Logged In 2 6 5 5 Output Power 2 10 5 11 Over Temperature chassis 2 3 5 10 Over Temperature power supply 2 10 5 11 link state database B 44 Lip command B 14 log archive B 34 clear B 34 copy 5 14 event B 34 B 56 power on self test B 47 logged in users B 48 Logged In LED 2 6 5 5 login limit B 1 loop port B 14 Loop Port Bypass B 37 Loop Port Enable B 37 5902
41. 5 FallingTrigger 1 SampleWindow 10 DecodeErrorsMonitoringEnabled True RisingTrigger 25 FallingTrigger 0 SampleWindow 10 ISLMonitoringEnabled True RisingTrigger 2 FallingTrigger 0 SampleWindow 10 LoginMonitoringEnabled True RisingTrigger 5 FallingTrigger 1 SampleWindow 10 B Command Line Interface Reset Command BE n Table B 4 Alarm Threshold Configuration Defaults Continued Parameter Default LogoutMonitoringEnabled True RisingTrigger 5 FallingTrigger 1 SampleWindow 10 LOSMonitoringEnabled True RisingTrigger 100 FallingTrigger 5 SampleWindow 10 Table B 5 SNMP Configuration Defaults Trap 1 5 Address Trap 1 5 Port Trap 1 5 Severity Trap 1 5 Version Trap 1 5 Enabled ObjectID AuthFailureTrap ProxyEnabled Parameter Default Contact Undefined Location Undefined Description QLogic SANbox2 FC Switch Trap 1 10 0 0 254 Traps 2 5 0 0 0 0 Undefined Warning 2 False 1 3 6 1 4 1 1663 1 1 1 1 11 SANbox2 16 False True B 22 59021 05 B d tt B Command Line Interface Simplify Reset Command SE Table B 6 System Configuration Defaults Parameter Default Ethernet Network Discovery Static Ethernet Network IP Address 10 0 0 1 Ethernet Network IP Mask 255 0 0 0 Ethernet Gateway Address 10 0 0 254 Admin Timeout 30 minutes SecurityEnabled False LocalLogEnabled True RemotelogEnabled False RemoteLogHostAddress 10 0 0 254
42. 50 06 04 82 bf d2 18 c2 50 06 04 82 bf d2 18 d2 10 00 00 00 c9 22 15 59021 05 B B 79 B Command Line Interface og q Simplify Zoning Command RE ooo a Notes B 80 59021 05 B Glossary Activity LED A port LED that indicates when frames are entering or leaving the port Alias A collection of objects that can be zoned together An alias is not a zone and can not have a zone or another alias as a member AL_PA Arbitrated Loop Physical Address Arbitrated Loop A Fibre Channel topology where ports use arbitration to establish a point to point circuit Arbitrated Loop Physical Address AL_PA A unique one byte valid value assigned during loop initialization to each NL Port on a Loop ASIC Application Specific Integrated Circuit BootP A type of network server Buffer Credit A measure of port buffer capacity equal to one frame Class 2 Service A service which multiplexes frames at frame boundaries to or from one or more N_Ports wit h acknowledgment provided 59021 05 B Class 3 Service A service which multiplexes frames at frame boundaries to or from one or more N_Ports without acknowledgment Domain ID User defined name that identifies the switch in the fabric E Port Expansion port A switch port that connects to another FC SW 2 compliant switch Expansion Port See E_Port Fabric Management Switch The switch through which the fabric is managed Fabric Name
43. E 2 8 Sa Me eg 2 8 Power Supplies cocina ace ainda 2 9 ERAS O IA 2 10 WICH REN En EE 2 11 Planning BIEL 3 1 Multiple Chassis Fabrics a a e 3 2 Domain ID Principal Priority and Domain ID Lock 3 2 Common T0P9lPgles sr 3 3 Cascade TODO E 3 3 MeshiTopology uragani lia 3 4 Multistage Topology fini 3 5 En legt Te 3 6 Distances nie 3 6 Bandwidth E 3 7 DN uereg EEN et CSS ES ENEE Re ee ess 3 7 DEVICE ACCESS a Here aa ieee a 3 8 EE ct totalidad ino 3 9 Access Control List Hard Zones sssssssreerrerrttrrrrnrrtnrrenrtnnntnn nren nnn nrnna 3 9 Virtual Private Fabric Hard Zones 3 10 Fabric Manage entitats 3 10 Fabrie Secufiiy ici iii een 3 11 Installation Site Requirements aspra iaia ia liana 4 1 Fabric Management Workstation nenn 4 1 Switch Power Requirements nn 4 1 Environmental Condrttons rrer reeersrrrsrrrerrrnrrrnrrrerrerereerre n 4 2 Installing EC EEN 4 2 Mount the SWI nase ea Teen BA 4 3 Install SFP Transceivers ii 4 4 59021 05 B SANbox2 16 Fibre Channel Switch Installation Guide Mu U 4 2 3 4 2 4 4 2 4 1 4 2 4 2 4 2 5 4 2 6 4 2 7 4 2 8 4 2 9 4 2 10 4 2 11 4 2 12 4 2 13 4 2 14 4 3 4 3 1 4 3 2 4 3 3 4 4 Section 5 5 1 5 1 1 5 1 1 1 5 1 1 2 5 1 1 3 5 1 1 4 5 1 1 5 5 1 2 5 1 2 1 5 1 2 2 5 2 5 2 1 5 2 2 5 2 3 5 2 4 5 2 5 5 3 5 3 1 5 3 2 59021 05 B Connect the Sw
44. E EE 2 5 2 7 Ethernet Port alal Nee EES e eegen 2 8 2 8 Serial POM EE 2 8 2 9 Power Supply Components see 2 9 2 10 Fans abate ee A 2 10 3 1 Cascade with a Loop Topology seem ee 3 3 3 2 Mesh Topology arn a a a a A A a A AA EA A ARAE rA aae aTa ESA 3 4 3 3 Multistage Keele VE 3 5 4 1 SANbox2 16 Fibre Channel Switch 4 2 4 2 Installing Rack Mount Brackets corn 2 en det 4 4 4 3 Ethernet and Serial Cable Connections nn 4 8 59021 05 B Page vii SANbox2 16 Fibre Channel Switch d tt Installat 6 2 6 4 Table 2 1 3 1 4 1 B 1 B 2 B 3 B 4 B 5 B 7 B 8 B 10 B 11 B 12 B 13 Page viii ion Guide Simplify POT LEOGged IN LED WEE 5 5 Logged In LED Indications une ie Elan 5 5 Chassis and Power Supply LEDS nn nn 5 9 SFP Transceiver Installation ee ee 6 2 Power Supply Removal atriale aaa 6 3 Fam Removal ardid ts 6 4 Fan Installation for Switch Model SB2A 16B nenn nnnnnnn 6 5 Tables Page Serial Port Pin Identification ee 2 9 Port to Port Transmission Gombin tions u ene ee 3 7 Ponlo PO L leney EE 3 7 Management Workstation Requirements 4 1 Commands Listed by Authority Level B 3 Switch Configuration Default a edad B 20 Port Neie e e e RRC B 20 Alarm Threshold Configuration Defaults nen nnnnnnnnnnnnnnnnnnnnnnnnnnn nenn B 21 SNMP Configuration Defaults senken nee B 22 System Configuration Defaults iii B 23 ele Port ee B 26 S
45. Info at the same time B 36 59021 05 B B Command Line Interface Set Port Command SE Set Port Command Authority Syntax Keywords 59021 05 B Sets port state and speed for the specified port temporarily until the next switch reset or new configuration activation This command also clears port counters Admin set port port_number bypass alpa clear enable speed transmission_ speed state state port_number Specifies the port Ports are numbered beginning with 0 bypass alpa Sends a Loop Port Bypass LPB to a specific Arbitrated Loop Physical Address ALPA or to all ALPAs on the arbitrated loop alpa can be a specific ALPA or the keyword ALL to choose all ALPAs clear Clears the counters on the specified port enable Sends a Loop Port Enable LPE to all ALPAs on the arbitrated loop speed transmission_speed Specifies the transmission speed for the specified port Choose one of the following port speed values 1Gb s One gigabit per second 2Gb s Two gigabits per second Auto The port speed is automatically detected state state Specifies one of the following administrative states for the specified port Online Places the port online Offline Places the port offline Diagnostics Prepares the port for testing Down Disables the port B 37 B Command Line Interface Set Setup Command e Q O O vmem m lt lt m m Set Setup Command Changes SNMP and
46. Merge Request 335 day month date time year I Eport 0xdd00b8b6 304 4 Port 0 8 LSDB Xchg timer set 336 day month date time year I Eport 0xdd00b8b6 304 4 Port 0 8 Sett ing attribute Oper UserPort 0 8 EpConnState Connected 59021 05 B B 57 B Command Line Interface d tt Show Perf Command Simplify U ooo o o Show Perf Command Authority Syntax Keywords B 58 Displays port performance in frames second and bytes second If you omit the keyword the command displays data transmitted out data received in and total data transmitted and received in frames second and bytes per second User show perf byte inbyte outbyte frame inframe outframe errors none Displays instantaneous performance data in bytes and frames for all ports byte Displays continuous performance data in total bytes second transmitted and received for all ports Type q and press the Enter key to stop the display inbyte Displays continuous performance data in bytes second received for all ports Type q and press the Enter key to stop the display outbyte Displays continuous performance data in bytes second transmitted for all ports Type q and press the Enter key to stop the display frame Displays continuous performance data in total frames second transmitted and received for all ports Type q and press the Enter key to stop the display
47. SMonitoringEnabled True RisingTrigger 100 FallingTrigger 5 SampleWindow 10 The following is an example of the Show Config Zoning command SANbox2 gt show config zoning Configuration Name default AutoSave True Default All 59021 05 B B 55 Show Log Command B Command Line Interface d tt Simplify BE 0 OO ooo Show Log Command Authority Syntax Keywords Examples B 56 Displays the contents of the log or the parameters used to create entries in the log The log contains a maximum of 200 entries When the log reaches its entry capacity subsequent entries overwrite the existing entries beginning with the oldest User show log component level options port settings component Displays the components currently being monitored for events level Displays the event severity level needed to create an entry in the log If the severity level occurs on a port or on a component which is not defined no entry is made in the log options Displays the options used to set the component and log level attributes port Displays the ports being monitored for events If an event occurs which is of the defined level and on a defined component but not on a defined port no entry is made in the log settings Displays the current settings for component level and port This command is equivalent to executing the following commands separately Show Log Component Show Log Level and Show Log Port The
48. Syntax whoami Examples The following is an example of the Whoami command SANbox2 gt whoami User name admin session2 Switch name SANbox2 Switch domain ID 1 lt 0x1 gt 59021 05 B B 69 B Command Line Interface d tt Zone Command Simplify E o o Zone Command Authority Syntax Keywords B 70 Manages zones and zone membership on a switch Admin authority and a Zoning Edit session Refer to the Zoning Command on page B 77 for information about starting a Zoning Edit session The List Members and Zonesets keywords are available with User authority and do not require a Zoning Edit session zone add zone members copy zone_source zone_destination create zone delete Zone list members zone remove zone members rename zone_old zone_new type zone zone_type zonesets zone add zone members Specifies one or more ports devices given by members to add to the zone named zone A zone can have a maximum of 256 members members can have one of the following formats u Domain ID and port number pair Domain ID Port Number Domain IDs and port numbers are in decimal Ports are numbered beginning with 0 m 6 character hexadecimal device Fibre Channel address hex m 16 character hexadecimal worldwide port name WWPN with the format XX XX XX XX XX XX XXIXX a Alias name The application verifies that the members format is correct but does not validat
49. The following is an example of a successful Ping command SANbox2 gt ping 10 20 11 57 Ping command issued Waiting for response SANbox2 gt Response successfully received from 10 20 11 57 This following is an example of an unsuccessful Ping command SANbox2 gt ping 10 20 10 100 Ping command issued Waiting for response Alarm Msg day month date time year A4101 0xdd0090e8 289 cmon unable to send ping to IP address 10 20 10 100 No response from 10 20 10 100 Unreachable B 16 59021 05 B d tt B Command Line Interface Simplify Ps Command SE Ps Command Displays current system process information Authority User Syntax ps Examples The following is an example of the Ps command SANbox2 gt ps PID PPID CPU TIME ELAPSED COMMAND 298 292 0 0 00 00 00 59 42 ens 299 292 0 0 00 00 00 59 42 ens 300 292 0 0 00 00 00 59 42 dlog 301 292 0 3 00 00 53 59 42 ds 302 292 0 2 00 00 29 59 42 mgmtApp 303 292 0 0 00 00 02 59 42 nserver 304 292 0 0 00 00 00 59 42 mserver 305 292 0 1 00 00 15 59 42 util 306 292 0 0 00 00 04 59 42 eport 307 292 1 2 00 02 53 59 41 PortApp 308 292 0 0 00 00 01 59 41 zoning 309 292 0 0 00 00 00 59 41 diagApp 59021 05 B B 17 B Command Line Interface d tt Quit Command Simplify ee SSe Quit Command Closes the Telnet session Authority User Syntax quit exit or logout B 18 59021 05 B B Command Line Interface Reset Command SE Reset Comma
50. The two components of security are user authentication and fabric security The user must be authenticated before gaining access to a switch If an invalid account name password combination is entered that user can not access the switch and thus can not gain access to the fabric If security is enabled True and a valid account name password combination is entered that user can access the switch but can not execute any command that exceeds their authority privileges level If security is disabled False and a valid account name password combination is entered that user has access to all switches in the fabric and can execute all commands both user and admin regardless of their authority privilege level Examples The following is an example of the Set Setup SNMP command SANbox2 gt admin start SANbox2 admin gt set setup snmp A list of attributes with formatting and current values will follow Enter a new value or simply press the ENTER key to accept the current value If you wish to terminate this process before reaching the end of the list press q or Q and the ENTER key to do so Trap Severity Options unknown emergency alert critical error warning notify info debug mark Contact string max 32 chars lt sysContact undefined Location string max 32 chars sysLocation undefined TraplAddress dot notated IP Address 20 20 7215 TraplPort decimal value 162 B 40 59021 05 B Simplify Set Se
51. User Command on page B 67 for information about creating user accounts m Refer to the Set Setup Command on page B 38 and the System keyword for information about fabric security and the enforcement of user accounts and authority levels 59021 05 B 3 11 Fabric Security 3 Planning df RN Notes 3 12 59021 05 B Section 4 Installation This section describes how to install and configure the SANbox2 16 switch It also describes how to load new firmware 4 1 Site Requirements Consider the following items when installing a SANbox2 16 switch Fabric management workstation Power requirements Environmental conditions 4 1 1 Fabric Management Workstation The requirements for fabric management workstations running SANbox Manager are described in Table 4 1 Table 4 1 Management Workstation Requirements Operating System Windows NT 2000 95 98 E Linux 6 2 Red Hat E Solaris Memory 128 MB or more Disk Space 150 MB per installation Processor 300 MHz or faster Hardware CD ROM drive RS 232 serial port RJ 45 Ethernet port Internet Browser Microsoft Internet Explorer or Netscape Navigator Telnet workstations require an RJ 45 Ethernet port or an RS 232 serial port and an operating system with a Telnet client 4 1 2 Switch Power Requirements Operating voltage requirements are as follows 90 to 137 Vac 47 to 63 Hz 180 to 265 Vac 47 to 63 Hz 59021 05 B 4 1 4 Installation dog q S
52. Zoneset List Zones Zoning Active List off Allows continuous display of information without a break 59021 05 B Simplify Set Command d tt B Command Line Interface aaa port option Sets port state and speed for the specified port temporarily until the next switch reset or new configuration activation Refer to the Set Port Command on page B 37 setup option Changes SNMP and system configuration settings Refer to the Set Setup Command on page B 38 switch state Temporarily changes the administrative state for all ports on the switch to the state given by state The previous Set Config Switch settings are restored after a switch reset or a reactivation of a switch configuration state can be one of the following online Places all ports online offline Places all ports offline diagnostics Prepares all ports for testing Examples The following examples enables and disables the beacon SANbox2 gt set beacon on Command succeeded SANbox2 gt set beacon off Command succeeded 59021 05 B B 25 B Command Line Interface gi Set Config Command q Simplify U ooo 22222 Set Config Command Authority Syntax Keywords B 26 Sets switch port alarm threshold and zoning configuration parameters Admin authority and a Config Edit session set config port port_number ports port_number switch threshold zoning port port_number Initiates an edit session in which t
53. accounts from the switch 5 3 5 Maintenance Copy Log Files This option copies all log file buffers to a file on the switch named ogfile You can use FTP to download this file to the management workstation 5 3 6 Maintenance Remove Switch Config This option deletes all configurations from the switch except for the default configuration This restores switch configuration parameters to the factory defaults except for user accounts and zoning Refer to Table B 2 though Table B 6 for the factory default values 5 3 7 Maintenance Remake Filesystem In the event of sudden loss of power it is possible that the switch configuration may become corrupt The file system on which the configuration is stored must be re created This option resets the switch to the factory default values including user accounts and zoning Refer to Table B 2 though Table B 6 for the factory default values CAUTION f you choose the Remake Filesystem option you will lose all changes made to the fabric configuration that involve that switch such as password and zoning changes You must then reconfigure the portions of the fabric that involve the switch 5 3 8 Maintenance Reset Switch This option closes the Telnet session exits maintenance mode and reboots the switch using the current switch configuration All unpacked firmware image files that reside on the switch are deleted 5 14 59021 05 B 59021 05 B Section 6 Removal Replacement
54. agnostics eiii Rte ne Tee 5 9 Chassis Over Temperature LED is Illuminated 5 10 Input Power LED Is Extinguished 2 22 5 10 Fan Fail LED is Illuminated nenn nnnnnnnnnnnennnene 5 10 Output Power LED Is Extinguished 5 11 Power Supply Over Temperature LED is Illuminated 5 11 Recoverid EE CEET agio 5 12 Maintenance Exit 5 13 Maintenance Image UnpacK nn nnHHannnnsnen naar 5 13 Page v SANbox2 16 Fibre Channel Switch d tt Installation Guide Simplify ee 5 3 3 5 3 4 5 3 5 5 3 6 5 3 7 5 3 8 Section 6 6 1 6 2 6 3 Maintenance Reset Network Config 5 14 Maintenance Reset Password File 5 14 Maintenance Copy Log Files 5 14 Maintenance Remove Switch Config 5 14 Maintenance Remake Filesystem nee nnnnnnnnnnnnnn nn 5 14 Maintenance Reset Switch 5 14 Removal Replacement SEP Transceivers u erinnern rasen 6 2 PowersSupplies riale HE ine 6 3 INS li Riano 6 4 Appendix A Specifications A 1 A 2 A 3 A4 AN A 6 A 7 A 8 A 9 Appendix B B 1 B 2 B 3 Page vi ebe ele Le TEE A 1 Switch Maintainability sosia orient A 2 Fabric Management ee A 3 Switch DIMENSIONS x iii it ei A 3 Switch Electricali allea T E ia A 3 Switch Environmental sise A 4 Switch Regulatory CeritiGatlons ss cnrs tf A 4 Shortwave Las
55. ake openings clear Are both fans operating and producing air flow Yes Continue E No Remove any debris from fan intakes if necessary Replace any fan that is not operating Refer to Section 6 Removal Replacement If the condition remains continue Consider the ambient air temperature near the switch and clearance around the switch Make necessary corrections If the condition remains continue Replace the power supply Refer to Section 6 Removal Replacement If the condition remains contact your authorized maintenance provider 5 11 Recovering a Switch Simplify 5 Diagnostics Troubleshooting d tt ee 5 3 Recovering a Switch A switch can become inoperable or unmanageable for the following reasons Hi Firmware becomes corrupt m P address is lost E Switch configuration becomes corrupt H Forgotten password In these specific cases you can recover the switch using maintenance mode Maintenance mode temporarily returns the switch IP address to 10 0 0 1 and provides opportunities to do the following m Unpack a firmware image file H Restore the network configuration parameters to the default values al Remove all user accounts and restore the Admin account name password to the default Copy the log file Restore factory defaults for all but user accounts and zoning Restore all switch configuration parameters to the factory default values Reset the switch To recover a switch do the following 1 Place the
56. any and what types of switches are needed Consider the distribution of public and private devices as well as targets and initiators Public devices have full Fibre Channel addressing capability and therefore can communicate with any other public device on the fabric An F_Port supports a single public device An FL_Port can support up to 126 public devices in an arbitrated loop Private devices do not have full Fibre Channel addressing capability only the Arbitrated Loop Physical Address ALPA portion A TL_Port provides a proxy for a loop of up to 124 private target devices allowing communication with up to 63 off loop public initiator devices Consider the number of private devices in the fabric and the number of off loop devices with which the private devices must communicate The SANbox2 16 Fibre Channel switch uses SFP optical transceivers but the device host bus adapters you are using may not Consider whether the device adapters use SFP transceivers or Gigabit Interface Converters GBIC and choose fiber optic cable accordingly Use LC type cable connectors for SFP transceivers and SC type cable connectors for GBIC transceivers 3 1 3 Planning dt Multiple Chassis Fabrics ee 3 2 Multiple Chassis Fabrics By connecting switches together you can expand the number of available ports for devices Each switch in the fabric is identified by a unique domain ID and the fabric will automatically resolve domain ID conflicts Becau
57. assis Over Temperature LED illuminates do the following 1 Inspect the chassis fans Are the intake openings clear Are both fans operating and producing air flow Yes Continue m No Remove any debris from fan intakes and exhausts if necessary Replace any fan that is not operating Refer to Section 6 Removal Replacement If the condition remains continue 2 Consider the ambient air temperature near the switch Make necessary corrections If the condition remains shut down the switch immediately and contact your authorized maintenance provider 5 2 2 Input Power LED Is Extinguished The Input Power LED illuminates to indicate that the switch logic circuitry is receiving proper voltages If the Input Power LED is extinguished inspect the Output Power LED Is the Output Power LED illuminated H Yes Contact your authorized maintenance provider E No Refer to Output Power LED Is Extinguished on page 5 11 523 Fan Fail LED is llluminated The Fan Fail LED illuminates to indicate a malfunction with one or both of the chassis fans If the Fan Fail LED illuminates do the following 1 Inspect the chassis fan connections Remove and reinstall the chassis fan Refer to Section 6 Removal Replacement If the condition remains continue 2 Are both fans operating and producing equal air flow m Yes Contact your authorized maintenance provider n No Replace the weaker chassis fan Refer to Section 6 Removal Replacem
58. ata tab in SANbox Manager faceplate display or the Show Alarm command Pertinent alarm log messages will point to one or more of the following conditions E E_Port isolation n Excessive port errors 59021 05 B 5 5 5 Diagnostics Troubleshooting dog POST Diagnostics q Simplify E ee 5 1 2 1 E Port Isolation A Logged In LED error indication is often the result of E_Port isolation An isolated E_Port is indicated by a red link in the SANbox Manager topology display E_Port isolation can be caused by conflicting domain IDs conflicting timeout values or conflicting zone membership between active zone sets Refer to the SANbox2 8c 16 Switch Management User s Guide for information about how to change domain IDs timeout values and edit zoning 5 6 Review the alarm log and do the following to diagnose and correct an isolated E Port di Display the fabric domain IDs using the Show Domains command or the Switch data tab in the SANbox Manager topology display Are all domain IDs in the fabric unique Yes Continue H No Correct the domain IDs on the offending switches using the Set Config Switch command or the SANbox Manager Switch Properties window Reset the port Ifthe condition remains continue Compare the RA_TOV ED_TOV RT_TOV timeout values for all switches in the fabric using the Show Config Switch command or the Switch data tab of the SANbox Manager topology display Is each timeout value the same on e
59. ation q Simplify Installing a Switch ls 4 Confirm that the Output Power LEDs on both power supplies are illuminated If not do the following a Check voltage at the AC power source b Inspect the power cord c Replace the power supply 5 Observe the Heartbeat LED to determine the results of the Power On Self Test POST The POST tests the condition of firmware memories data paths and switch logic circuitry and passes a blink code to the Heartbeat LED If the Heartbeat LED blinks steadily about once per second the POST was successful and you can continue with the installation process Any other blink pattern appears indicates that an error has occurred Refer to Heartbeat LED Blink Patterns on page 5 1 for more information about the error blink pattern 59021 05 B 4 7 4 Installation Installing a Switch E 4 2 4 Connect the Management Workstation to the Switch Connect the management workstation to the switch in one of three ways Indirect Ethernet connection from the management workstation to the switch RJ 45 Ethernet connector through an Ethernet switch or a hub This requires a 10 100 Base T straight cable as shown in Figure 4 3 With this method you can manage the switch with the SANbox Manager application or Command Line Interface Direct Ethernet connection from the management workstation to the switch RJ 45 Ethernet connector This requires a 10 100 Base T cross over cable as shown in Figur
60. b Point to and select Files then select File Manager c In File Manager double click the CD ROM icon and then double click the Sansurfer folder d Inthe Sansurfer folder double click the Start_Here htm file to open the SANsurfer Management Suite start page in your default browser 2 Onthe SANsurfer Management Suite start page choose the SANbox Switch Software button 3 On the SANbox Switch Software page scroll to the SANbox2 2Gb Series area 4 In the Solaris column choose the SANbox Manager link to open the Save As window 5 Enter a path name to save the sansurfer_solaris_install pkg file and choose the Save button 6 Open a terminal window for the directory in which the sansurfer_solaris_install pkg file was saved and enter the following command chmod x sansurfer_solaris_install pkg Press the Enter key Enter the following command sansurfer_solaris_install pkg 9 Press the Enter key and follow the SANbox Manager installation instructions Note If you download SANbox Manager from a server be sure the 59021 05 B downloaded file has execute permission before installing 4 13 4 Installation Installing a Switch E OO o 1 a g g a amp amp i g iz z z gya 4 2 9 SANbox2 Installation Disk Windows Installation To install the SANbox Manager application on Windows from the SANbox2 Installation Disk do the following 1 4 2 10 Close all programs currently running and
61. ba SANbox2 16 Fibre Channel Switch Installation Guide 59021 05 B Page i SANbox2 16 Fibre Channel Switch Installation Guide U ooo e 2 Information furnished in this manual is believed to be accurate and reliable However QLogic Corporation assumes no responsibility for its use nor for any infringements of patents or other rights of third parties which may result from its use QLogic Corporation reserves the right to change product specifications at any time without notice Applications described in this document for any of these products are for illustrative purposes only QLogic Corporation makes no representation nor warranty that such applications are suitable for the specified use without further testing or modification QLogic Corporation assumes no responsibility for any errors that may appear in this document QLogic SANbox SANbox2 SANblade and SANsurfer are trademarks or registered trademarks of QLogic Corporation Solaris is a registered trademarks of Sun Microsystems Inc Pentium is a registered trademark of Intel Corporation Linux is a registered trademark of Linus Torvalds Microsoft Windows NT and Windows 2000 and Internet Explorer are registered trademarks of Microsoft Corporation Netscape Navigator is a registered trademark of Netscape Communications Corporation Red Hat is a registered trademark of Red Hat Software Inc All other brand and product names are trademarks or registered trademar
62. back Command Authority Syntax Notes Examples Loads the fallback version of the firmware from switch memory The switch stores two versions of the firmware This command alternately activates the two versions Admin fallback m The Show Switch command displays the available firmware versions and the currently active version m After executing the Fallback command reset the switch for the firmware to be placed in effect The following is an example of the Fallback command SANbox2 gt admin start SANbox2 admin gt fallback Reverting to previous software image Please confirm y n n y SANbox2 gt admin end 59021 05 B B Command Line Interface Help Command ZZZ A Help Command Authority Syntax Keywords Examples Displays a brief description of the specified command and its keywords User help command keyword command Displays a summary of the command given by command and its keywords If you omit command the system displays all available commands from which to choose keyword Displays a summary of the keyword given by keyword belonging to the command given by command If you omit keyword the system displays the available keywords for the specified command all Displays a list of all available commands including command variations The following is an example of the Help Set command SANbox2 gt help set set SET_OPTIONS There are many attributes that can be
63. be the same The default is public Write community password that authorizes an SNMP agent to write information to the switch This is a write only field The value on the switch and the SNMP management server must be the same The default is private B 38 59021 05 B Simplify Set Setup Command d tt B Command Line Interface SE Table B 11 SNMP Configuration Settings Entry Description TrapCommunity Trap community password that authorizes an SNMP agent to receive traps This is a write only field The value on the switch and the SNMP management server must be the same The default is public AuthFailure Trap Enables True or disables False the generation of traps in response to trap authentication failures The default is False ProxyEnabled Enables True or disables False SNMP communication with other switches in the fabric The default is True system Prompts you in a line by line fashion to change system configuration settings Table B 12 describes the system configuration fields For each parameter enter a new value or press the Enter key to accept the current value shown in brackets Table B 12 System Configuration Settings Entry Description EthONetworkDiscovery Boot Method 1 Static 2 Bootp 3 DHCP 4 RARP EthONetworkAddress Internet Protocol IP address for the Ethernet port EthONetworkMask Subnet mask address for the Ethernet port EthOGate
64. ble Is the problem corrected m Yes Complete No Continue 4 Inspect the device to which the affected port is connected and confirm that the device and its HBA are working properly Make repairs and corrections as needed If the condition remains contact your authorized maintenance provider 5 8 59021 05 B Simplify Chassis Diagnostics d tt 5 Diagnostics Troubleshooting ZZZ 5 2 Chassis Diagnostics Chassis diagnostics are indicated by the chassis and power supply LEDs as shown in Figure 5 3 Chassis Over Output Power LED p Temperature LED Fan Fail LED Power Supply Over Temperature LED Input Power LED 0000 LN Figure 5 3 Chassis and Power Supply LEDs The following conditions are described m Chassis Over Temperature LED is illuminated m Input Power LED is extinguished n Fan Fail LED is illuminated H Output Power LED is extinguished Power supply Over Temperature LED is illuminated Note The chassis and power supply Over Temperature LEDs are different The chassis LED indicates an over temperature condition in the switch logic circuitry the power supply LED indicates an over temperature condition in the power supply 59021 05 B 5 9 5 Diagnostics Troubleshooting d tt Chassis Diagnostics Simplify U 9 2 1 Chassis Over Temperature LED is Illuminated The chassis Over Temperature LED illuminates to indicate that the switch logic circuitry is overheating Ifthe ch
65. cks Electrical Equipment 19 Inch and Associated Panels The brackets shown in Figure 4 2 are provided with the switch so that the switch can be secured in a shelf The brackets alone are not designed to support the weight of the switch Figure 4 2 Installing Rack Mount Brackets 4 2 2 Install SFP Transceivers The switch will support a variety of interconnection media Refer to SFP Transceivers on page 6 2 for information about removing and installing SFP transceivers 4 4 59021 05 B gi 4 Installation q Simplify Installing a Switch SE 4 2 3 Connect the Switch to AC Power WARNING This product is supplied with a 3 wire power cable and plug for the user s safety Use this power cable in conjunction with a properly grounded outlet to avoid electrical shock An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the switch chassis It is the responsibility of the customer to ensure that the outlet is correctly wired and grounded to prevent electrical shock You may require a different power cable in some countries because the plug on the cable supplied with the equipment will not fit your electrical outlet In this case you must supply your own power cable The cable you use must meet the following requirements m For 125 Volt electrical service the cable must be rated at 10 Amps and be approved by UL and CSA m For 250 Volt electrical service The
66. command SANbox2 gt uptime Elapsed up time 0 day s 2 hour s 28 min s 44 sec s Reason last reset NormalReset B 66 59021 05 B Simplify User Command d tt B Command Line Interface SE User Command Administers or displays user accounts Authority Admin The List keyword is available with User authority Syntax user accounts add delete account _ name list Keywords accounts Displays all user accounts that exist on the switch add Add a user account to the switch After this command is executed the administrator will be prompted for the information needed to establish the user account switch can have a maximum of 15 user accounts Account names are limited to 15 characters passwords are limited to 31 characters delete account_name Deletes the account name given by account_name from the switch list Displays the list of users currently logged in and their session numbers Provides the same function as the Show Users command This keyword is valid for User authority and does not require an admin session Examples The following is an example of the User Accounts command SANbox2 admin gt user accounts Current list of user accounts admin admin authority True userl admin authority False user2 admin authority False user3 admin authority True 59021 05 B B 67 B Command Line Interface d tt User Command Simplify EE ee The following is an example of the User Add
67. d False Trap4Address 0 0 0 0 Trap4Port 162 Trap4Severity warning Trap4Version 2 Trap4Enabled False Trap5Address 0 0 0 0 Trap5Port 162 Trap5Severity warning Trap5Version 2 Trap5Enabled False Object ID 1 3 6 1 4 1 1663 1 1 1 1 11 AuthFailureTrap True ProxyEnabled True The following is an example of the Show Setup System command SANbox2 gt show setup system System Information Eth0NetworkDiscovery Static EthONetworkAddress AO 2011 32 EthONetworkMask 255 255 25250 Eth0GatewayAddress 10 20 8 254 AdminTimeout 30 TempMonitoringWarning 65 TempMonitoringFailure 70 TempFailurePortShutdown False SecurityEnabled False LocalLogEnabled True RemoteLogEnabled False RemoteLogHostAddress 10 0 0 254 59021 05 B B 61 B Command Line Interface d tt Shutdown Command Simplify a ee Shutdown Command Terminates all data transfers on the switch at convenient points and closes the Telnet session Always power cycle the switch after entering this command Authority Admin Syntax shutdown Notes Always use this command to effect an orderly shut down before removing power from the switch Failure to do so could corrupt the flash memory and the switch configuration B 62 59021 05 B B Command Line Interface Test Command EE Test Command Authority Syntax Keywords Examples 59021 05 B Tests ports using internal SerDes level external SFP and online loopback tests Internal and external tests require t
68. deWWN 20 00 00 e0 8b 07 a8 bc PortType N Description NULL IPAddress 0 0 0 0 The following is an example of the Show Version command SANbox2 gt show version SystemDescription QLogic SANbox2 FC Switch EthONetworkAddress 10 0 0 1 use set setup system to update MACAddress 12 34 56 78 ab cd WorldWideName 10 00 00 c0 dd 00 90 a4 SymbolicName SANbox2 SWImageVersion V1 5 1 1 12 SWImageBuiltDate day month date time year DiagnosticsStatus Passed SecurityEnabled False B 52 59021 05 B B Command Line Interface Show Config Command ls Show Config Command Authority Syntax Keywords Examples 59021 05 B Displays switch port alarm threshold and zoning attributes for the current configuration User show config port port_ number switch threshold zoning port port_number Displays configuration parameters for the port number given by port_number Ports are numbered beginning with 0 If port_number is omitted all ports are specified switch Displays configuration parameters for the switch threshold Displays alarm threshold parameters for the switch zoning Displays zoning configuration parameters for the switch The following is an example of the Show Config Port command SANbox2 gt show config port 3 Configuration Name default Port Number 3 AdminState Online LinkSpeed Auto PortType GL ISLSecurity Any SymbolicName Port3 ALFairness False DeviceScanEnabled True ForceOffli
69. des for the configuration control maintenance of the fabric Supported platforms include Windows Windows NT Solaris and Linux The SANbox Manager application can manage multiple fabrics Consider how many fabrics will be managed how many management workstations are needed and whether the fabrics will be managed with the CLI or SANbox Manager The switch supports a combined maximum of 15 logins This includes SANbox Manager inband and out of band logins Application Programming Interface API inband and out of band logins and Telnet logins Of this 15 there can be a combined maximum of 10 SANbox Manager and API logins Additional logins will be refused 3 10 59021 05 B df 3 Planning Fabric Security ls 3 6 Fabric Security You manage fabric security on a switch basis through the creation of user accounts Each account consists of an account name a password and an authority level There are two authority levels User and Admin These authority levels apply to SANbox Manager and to the CLI User authority permits only monitoring and display tasks Admin authority permits all management tasks including user administration Furthermore you can enable or disable the enforcement of user accounts and authority levels Consider your fabric security needs who the system administrators will be and authority levels they should have m Refer to Commands on page B 3 for more information about authority levels m Refer to the
70. e SE The following is an example of the Zone Zonesets command SANbox2 gt zone zonesets zonel Current List of ZoneSets for Zone wwn_b0241f zone Set L 59021 05 B B 73 B Command Line Interface d tt Zoneset Command Simplify A oe Ave e q O o o 2 Zoneset Command Authority Syntax Keywords B 74 Manages zone sets and zone set membership across the fabric Admin authority and a Zoning Edit session Refer to the Zoning Command on page B 77 for information about starting a Zoning Edit session The Active List and Zones keywords are available with User authority You must close the Zoning Edit session before using the Activate and Deactivate keywords zoneset activate zone_set active add zone_set zone_list copy zone_set_source zone_set_destination create zone_set deactivate delete zone_set list remove zone_set zone_list rename zone_set_old zone_set_new zones zone_ set activate zone_set Activates the zone set given by zone_set This keyword deactivates the active zone set Close the Zoning Edit session before using this keyword active Displays the name of the active zone set This keyword is available with User authority and does not require a Zoning Edit session add zone_set zone_list Adds a list of zones and aliases given by zone_list to the zone set given by zone_set Zone and alias names are delimited by spaces in zone _list This keyword requi
71. e Number of class 2 and class 3 fabric busy F_BSY frames generated by this port in response to incoming frames This usually indicates a busy condition on the fabric or N_Port that is preventing delivery of this frame Flowerrors Received a frame when there were no available credits FReject Number of frames from devices that were rejected InvalidCRC Invalid CRC detected InvalidDestAddr LIP AL PD AL PS Invalid destination address detected Number of F7 AL_PS LIPs or AL_PD vendor specific resets performed LIP_F7 AL PS This LIP is used to reinitialize the loop An L_port identified by AL_PS may have noticed a performance degradation and is trying to restore the loop LIP_F8_AL PS This LIP denotes a loop failure detected by the L_port identified by AL_PS B 45 B Command Line Interface Show Command U oo oo 0202 Table B 13 Show Port Parameters Continued Entry Description LIP_F7_F7 LIP_F8_F7 Link Failures Login Logout LoopTimeouts LossOfSync PrimSeqErrors RxLinkResets RxOfflineSeq TotalErrors TotalLIPsRecvd TotalLinkResets TotalOfflineSeq TotalRxFrames TotalRxWords TotalTxFrames Total TxWords A loop initialization primitive frame used to acquire a valid AL_PA A loop initialization primitive frame used to indicate that a loop failure has been detected at the receiver Number of optical link failures detected by this port A link failure is
72. e that such a port exists copy zone_source zone_destination Creates a new zone named zone_destination and copies the membership into it from the zone given by zone_source create zone Creates a zone with the name given by zone An zone name must begin with a letter and be no longer than 64 characters Valid characters are 0 9 A Z a z _ and The zoning database supports a maximum of 1000 zones delete zone Deletes the specified zone given by zone from the zoning database Ifthe zone is a member of the active zone set the zone will not be removed from the active zone set until the active zone set is deactivated 59021 05 B d tt B Command Line Interface Simplify Zone Command SE list Displays a list of all zones and the zone sets of which they are members This keyword is valid for User authority and does not require a zoning edit session members zone Displays all members of the zone given by zone This keyword is available with User authority and does not require a Zoning Edit session remove zone members Removes the ports devices given by members from the zone given by zone members can have one of the following formats Domain ID and port number pair Domain ID Port Number Domain IDs and port numbers are in decimal Ports are numbered beginning with 0 m 6 characterhexadecimal device Fibre Channel address hex m 16 character hexadecimal worldwide port name WWPN with
73. e 4 3 With this method you can manage the switch with the SANbox Manager application or Command Line Interface Serial port connection from the management workstation to the switch RS 232 serial port connector This requires a null modem F F DB9 cable as shown in Figure 4 3 With this method you can manage the switch with Command Line Interface Indirect Ethernet Direct Ethernet Serial RS 232 RJ 45 Connection RJ 45 Connection Connection 8 1 8 1 5 1 00000 hy bei SE 8 8 8 8 9 9 7 7 7 7 8 8 6 6 6 6 7 i 7 5 5 5 5 6 6 4 4 4 4 5 gt 5 3 gt 3 3 3 4 4 2 2 2 2 3 3 1 1 1 1 2 2 1 1 Figure 4 3 Ethernet and Serial Cable Connections 59021 05 B gi 4 Installation q Simplify Installing a Switch SE 4 2 4 1 Ethernet Connection To establish an Ethernet connection do the following 1 Connect a 10 100 Base T cross over cable from an RJ 45 port on the management workstation directly to the RJ 45 Ethernet port or a 10 100 Base T straight cable indirectly over an Ethernet network 2 Login to the switch with the SANbox Manager application or the Telnet CLI using the default switch IP address 10 0 0 1 The default account name and password are admin password 4 2 4 2 Serial Connection To establish a serial port connection do the following 1 Connect a null modem F F DB9 cable from a COM port on the management workstation to the RS 232 serial port on the switch 2 Configure the connection
74. e Server The default is 5000 msec PrincipalPriority The priority used in the FC SW 2 principal switch selection algorithm 1 is high 255 is low ConfigDescription The name for the configuration The default is undefined B 28 59021 05 B Simplify Set Config Command d tt B Command Line Interface ZZZ threshold Initiates a configuration session by which to generate and log alarms for selected events The system displays each event its thresholds and sampling interval one line at a time and prompts you for a value For each parameter enter a new value or press the Enter key to accept the current value shown in brackets These parameters must be saved in a configuration and activated before they will take effect Refer to the Config Command on page B 7 for information about saving and activating a configuration Table B 9 describes the Set Config Threshold parameters The switch will down a port if an alarm condition is not cleared within three consecutive sampling intervals by default 30 seconds An alarm is cleared when the threshold monitoring detects that the error rate has fallen below the falling threshold Table B 9 Set Config Threshold Parameters Parameter Description Threshold Monitoring Enabled Master enable disable parameter for all events Enables True or disables False the generation of all enabled event alarms The default is False CRCErrorsMonitoringEnabled The event type enabl
75. e disable parameter Enables DecodeErrorsMonitoringEnabled True or disables False the generation of alarms ISLMonitoringEnabled for each of the following events LoginMonitoringEnabled EB CRC errors LogoutMonitoringEnabled E Decode errors LOSMonitoringEnabled M SL connection count E Login errors M Logout errors M Loss of signal errors Rising Trigger The event count above which a rising threshold alarm is logged The switch will not generate another rising threshold alarm for that event until the count descends below the falling threshold and again exceeds the rising threshold Falling Trigger The event count below which a falling threshold alarm is logged The switch will not generate another falling threshold alarm for that event until the count exceeds the rising threshold and descends again below the falling threshold Sample Window The period of time in seconds in which to count events 59021 05 B B 29 Set Config Command Simplify B Command Line Interface d tt ee zoning Initiates an editing session in which to change switch zoning attributes The system displays each parameter one line at a time and prompts you for a value For each parameter enter a new value or press the Enter key to accept the current value shown in brackets Table B 10 Set Config Zoning Parameters Parameter Description AutoSave Enables True or disables False the saving of changes to active zone set in the
76. e is less competition for this bandwidth than with a cascade or a Multistage topology Mm Latency between any two device ports is no more than two chassis hops m 40 Fibre Channel ports are available for devices E MATA JL os O MC AMAN es eo ooo ee ee eS eo E O NINA E gig A aru il a CM iL Iv Kees Dam on OU Fan Figure 3 2 Mesh Topology 3 4 59021 05 B df 3 Planning Multiple Chassis Fabrics Tk 3 2 2 3 Multistage Topology A Multistage topology describes a fabric in which two or more edge switches connect to one or more core switches Each additional core switch increases the bandwidth to each edge switch by 200 MB s The Multistage fabric shown in Figure 3 3 has the following characteristics M Each link contributes up to 200 MB s of bandwidth between chassis Competition for this bandwidth is less than that of a cascade topology but grea
77. efinitions B 78 revert changes B 78 save edits B 78 Zoning command B 77 Index 6 59021 05 B
78. elnet Enter one of the following on the command line telnet XXX XXX XXX XXX or telnet switchname where xxx xxx xxx xxx is the switch IP address and switchname is the switch name associated with the IP address f A Telnet window opens prompting you for a login Enter an account name and password The default account name and password are admin password g Open an admin session to acquire the necessary authority li gt admin start e h Restore the configuration file Q li admin gt config restore i Reset the switch and close the Telnet session cli admin gt reset 5 4 59021 05 B gi 5 Diagnostics Troubleshooting q SES POST Diagnostics 5 1 2 Logged In LED Indications Port diagnostics are indicated by the Logged In LED for each port as shown in Figure 5 1 Logged In LED E 2 12 Al WM Eat 00 00 O SF 5 Figure 5 1 Port Logged In LED The Logged In LED has three indications H Logged in Continuous illumination H Loggingin Flashes at roughly once per second as shown in Figure 5 2 Error Flashes at roughly twice per second as shown in Figure 5 2 1 second Logging In Rea Sea ees Eror Rae Figure 5 2 Logged In LED Indications If a Logged In LED shows an error indication review the alarm log for messages regarding the affected port You can inspect the alarm log using the Alarm d
79. embers Specifies one or more ports devices given by members to add to the alias named alias An alias can have a maximum of 2000 members members can have one of the following formats u Domain ID and port number pair Domain ID Port Number Domain IDs and port numbers are in decimal Ports are numbered beginning with 0 m 6 character hexadecimal device Fibre Channel address hex m 16 character hexadecimal worldwide port name WWPN with the format XX XX XX XX XX XX XXIXX The application verifies that the alias format is correct but does not validate that such a port device exists copy alias_source alias_destination Creates a new alias named alias_destination and copies the membership into it from the alias given by alias_source create alias Creates an alias with the name given by alias An alias name must begin with a letter and be no longer than 64 characters Valid characters are 0 9 A Z a z _ and The zoning database supports a maximum of 256 aliases delete alias Deletes the specified alias given by alias from the zoning database Ifthe alias is a member of the active zone set the alias will not be removed from the active zone set until the active zone set is deactivated list Displays a list of all aliases This keyword is valid for User authority and does not require a zoning edit session or an admin session B 5 B Command Line Interface d tt Alias Command Simplify aE e
80. ent If the condition remains contact your authorized maintenance provider Note Removing a fan will not illuminate the Fan Fail LED 5 10 59021 05 B 5 Diagnostics Troubleshooting Chassis Diagnostics TTT PP be E IiP F I 5 2 4 Output Power LED Is Extinguished The Output Power LED illuminates to indicate that the power supply is producing the proper voltages If the Output Power LED is extinguished do the following 5 2 5 1 Inspect the power supply Over Temperature LED Is the power supply Over Temperature LED illuminated H Yes Refer to Power Supply Over Temperature LED is Illuminated on page 5 11 No Continue Inspect the power cables and connectors Are the cables unplugged Are the cables or connectors damaged H Yes Make necessary corrections or repairs If the condition remains continue ul No Continue Inspect the power source Is the power source delivering the proper voltage m Yes Continue H No Make necessary repairs If the condition remains continue Replace the power supply Refer to Section 6 Removal Replacement If the condition remains contact your authorized maintenance provider Power Supply Over Temperature LED is Illuminated The power supply Over Temperature LED illuminates to indicate that the power supply is overheating If the power supply Over Temperature LED illuminates do the following 59021 05 B 1 Inspect the chassis fans Are the int
81. equipment Unauthorized changes or modifications could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions m This device may not cause harmful interference and m This device must accept any interference received including interference that may cause undesired operation 1 6 2 Canadian Department of Communications Class A Compliance Statement This equipment does not exceed Class A limits for radio emissions for digital apparatus set out in Radio Interference Regulation of the Canadian Department of Communications Operation in a residential area may cause unacceptable interference to radio and TV reception requiring the owner or operator to take whatever steps necessary to correct the interference 1 4 59021 05 B gi 1 Introduction q Simplify Communications Statements SE 1 6 3 Avis de conformit aux normes du minist re des Communications du Canada Cet quipement ne d passe pas les limites de Classe A d mission de bruits radio lectriques por les appareils num riques telles que prescrites par le R glement sur le brouillage radio lectrique tabli par le minist re des Communications du Canada L exploitation faite en milieu r sidentiel peut entra ner le brouillage des r ceptions radio et t l ce qui obligerait le propri taire ou l op rateur prendre les dispositions n cwssaires pour en limine
82. er SFP 1G 2G multi mode A 5 Longwave Laser SFP 1G 2G single mode i A 6 Command Line Interface LOGGING On toa SWICA at dll rial ER B 1 Command Ent Heels B 2 CommandS acorralado la B 3 Admin Command iii B 4 Alias COmmannd EE B 5 Config Command seitens B 7 Date COmmmand BEE B 9 Fallback Command B 10 Help Command seen B 11 History Command ee B 12 Us eil D B 13 ApPCOMMA dit EE B 14 Pass WA COMMON iii ia E B 15 e ernennen atei B 16 PS Command ege iii scene e SEENEN ENEE ENEE EE B 17 Quit Commander el B 18 59021 05 B Simplify d tt SANbox2 16 Fibre Channel Switch Installation Guide Reset Commande B 19 Set COMMANG EE B 24 Set Config Command aussen seinen it B 26 Set Log C m En e E B 34 Set Port Command anal B 37 Set Setup Command issis nantes nina tr B 38 SHOW COMMANG EE B 43 Show Config Command au B 53 Show Log Command WEE B 56 Show Perf Command LR B 58 Show Setup Command B 60 Shutdown Command B 62 Test Command ss dame penis Rah AAA AE B 63 Uptime Commandes darte B 66 User Command nn aa B 67 Whoami Command ss B 69 Zone Command iii B 70 Zoneset COMMANA iii B 74 Zoning COMME EE B 77 Glossary Index Figures Figure Page 2 1 SANbox2 16 Fibre Channel Switch 2 1 2 2 Chassis Controls and LEDS sn nn nn 2 2 2 3 Chassis LEBE A eines 2 3 2 4 Fibre Channel Eeler e de De de 2 4 2 5 SEP EE EE 2 5 2 6 KOJA E a DEEE E
83. er along any axis 1g for 15 msec 8 g for 15 msec Two fans front to back or back to front depending on the switch model UL1950 CSA 22 2 No 950 EN60950 FCC Part 15B Class A VCCI Class A ITE CISPR 22 Class A EN 55022 Class A EN 61000 3 3 EN 61000 3 2 EN 55024 1998 FCC Part 15 UL United States cUL Canada TUV VCCI CE 59021 05 B gi A Specifications q Simplify Shortwave Laser SFP 1G 2G multi mode SE A 8 Shortwave Laser SFP 1G 2G multi mode Connector Duplex LC e ele e E Beige or black exposed connector surfaces Babes Fibre Channel 100 M6 SN I 50 um multimode Fibre Channel 200 M5 SN I or 200 M6 SN I 62 5 um multimode Wavelength een 830 860 nm Transmit PoWer 10 dBm minimum Receiver Sensitivity 16 dBm average Distance u ee 500 meters maximum using 50 micron fiber 300 meters maximum using 62 5 micron fiber Satellit DHHS 21 CFR J IEC 825 1 CENELEC EN 60825 1 VDE Standard nenn Small Form Factor Pluggable Multisource Agreement 59021 05 B A 5 A Specifications d tt Simplify Longwave Laser SFP 1G 2G single mode ee A 9 Longwave Laser SFP 1G 2G single mode Connector Duplex LC Color COMING id ramen Blue exposed connector surfaces Gabler nt d Fibre Channel 100SM LC L 9 um single mode W velengthiz2 emma 1270
84. es whether GS 3 management server commands will be accepted on the port It can be used to prevent in band management of the switch on any or all ports True False NL_Port Node Loop Port A Fibre Channel device port that supports arbitrated loop protocol N_Port Node Port A Fibre Channel device port in a point to point or fabric connection Output Power LED A power supply LED that indicates that the power supply is providing DC voltage to the switch Over Temperature LED A chassis LED or a power supply LED that indicates that the switch or power supply is overheating POST Power On Self Test Power On Self Test POST Diagnostics that the switch chassis performs at start up Private Device A device that can communicate only with other devices on the same loop 59021 05 B SANbox2 16 Fibre Channel Switch d tt Installation Guide Simplify SE Private Loop Zone A loop of private devices connected to a A set of ports or devices grouped together single switch port to control the exchange of information SANbox Manager Zone Set Switch management application A set of zones grouped together The active zone set defines the zoning for a SFF fabric Small Form Factor transceiver SFP Small Form Factor Pluggable A transceiver device smaller than a GigaBit Interface Converter that plugs into the Fibre Channel port Small Form Factor A transceiver device smaller than a GigaBit Interface C
85. ess the Enter key Sanbox2 login prom Password xxxx username host Itasca telnet 10 0 0 1 Trying 10 0 0104 Connected to 10 0 0 1 Escape character is 5 The following menu is displayed Enter 6 Remake Filesystem and press the Enter key to recreate the configuration file 0 Exit 1 Image Unpack 2 Reset Network Config 3 Reset Password File 4 Copy Log Files 5 Remove Switch Config 6 Remake Filesystem 7 Reset Switch Option 6 6 When the recreate process is complete select option 7 to reset the switch and exit maintenance mode 7 Ifa previously saved configuration file is available for the switch do the following to restore the configuration file a Establish communications with the switch using the File Transfer Protocol FTP Enter one of the following on the command line gt ftp XXX XXX XXX XXX or gt ftp switchname where xxx xxx xxx xxx is the switch IP address and switchname is the switch name associated with the IP address b Enter the following account name and password user images password images 59021 05 B 5 3 POST Diagnostics Simplify E 5 Diagnostics Troubleshooting d tt c Activate binary mode and copy the configuration file from the workstation to the switch The configuration file must be named configdata ftp gt bin ftp gt put configdata d Close the FTP session ftp gt quit e Establish communications with the switch using T
86. et Config Switch Parameters u eier eg deeg B 28 Set Config Threshold Parameters Ran ss B 29 set Config Zoning EE B 30 SNMP Configuration Settings es da B 38 System Ee e elen CEET B 39 Show Por Parameters a nee Ee ere B 45 59021 05 B Section 1 Introduction This manual describes the features and installation of the SANbox2 16 Fibre Channel switch firmware version 1 5 1 This manual is organized as follows Section 1 describes the intended audience related materials safety notices communications statements laser safety information electrostatic discharge sensitivity precautions accessible parts and technical support Section 2 is an overview of the switch It describes indicator LEDs and all user controls and connections Section 3 describes the factors to consider when planning a fabric Section 4 explains how to install and configure the switch Section 5 describes the diagnostic methods and troubleshooting procedures Section 6 describes the removal replacement procedures for all field replaceable units FRUs Appendix A lists the switch specifications Appendix B describes the Telnet command line interface Please read the communications statements and laser safety information later in this section Use this manual in conjunction with the SANbox2 8c 16 Switch Management User s Guide 1 1 Intended Audience This manual introduces users to the switch and explains its installation and se
87. following is an example of the Show Log Component command SANbox2 gt show log component Current settings for log component Eport The following is an example of the Show Log Level command SANbox2 gt show log level Current settings for log 59021 05 B d tt B Command Line Interface Simplify Show Log Command ZZZ 13 Gi 7i9MU The following is an example of the Show Log Options command SANbox2 gt show log options Allowed options for log component All None NameServer Mgmt Server Zoning Switch Chassis Blade Port Eport Snmp Other level Critical Warn Info None The following is an example of the Show Log command 327 day month date time year I Eport 0xdd00b8b6 304 4 Port 0 8 Eport State E_AO_GET_DOMAIN_ID 328 day month date time year I Eport 0xdd00b8b6 304 4 Port 0 8 FSPF PortUp state 0 329 day month date time year I Eport 0xdd00b8b6 304 4 Port 0 8 Send ing init hello 330 day month date time year I Eport 0xdd00b8b6 304 4 Port 0 8 Proc essing EFP oxid 0x8 331 day month date time year I Eport 0xdd00b8b6 304 4 Port 0 8 Epor t State E_A2_IDLE 332 day month date time year I Eport 0xdd00b8b6 304 4 Port 0 8 EFP WWN 0x100000c0dd00b845 len 0x30 333 day month date time year I Eport 0xdd00b8b6 304 4 Port 0 8 Send ing LSU oxid 0xc type 1 334 day month date time year I Eport 0xdd00b8b6 304 4 Port 0 8 Send Zone
88. hat the port be placed in diagnostic mode Refer to the Set Command on page B 24 for information about changing the port administrative state While the test is running the remaining ports on the switch remain fully operational Admin test port port_number test_type cancel status port port_number test_type Tests the port given by port_number using the test given by test_type If you omit test_type Internal is used test_type can have the following values internal Tests the SerDes This is the default The port must be in diagnostics mode to perform this test external Tests both the SerDes and SFP The port must be in diagnostics mode to perform this test and a loopback plug must be installed in the SFP online Tests one online port cancel Cancels the online test in progress status Displays the status of a test in progress or if there is no test in progress the status of the test that was executed last To run an internal SerDes or external SFP port test do the following 1 To start an admin session enter the following command and press the Enter key admin start 2 Place the port in Diagnostics mode enter the following command x port number and press the Enter key set port x state diagnostics B 63 Test Command Simplify B Command Line Interface d tt ee 3 Choose the type of port loopback test to run H Torun an internal loopback test enter the following test x interna
89. he translation entries list for each off loop initiator device that attempts to establish communication Soft or VPF zoning can be used to limit the number of potential initiators to 63 Zone membership must be done by worldwide name or domain ID and port ID TL_Ports connect to devices that conform to the Fibre Channel Private Loop SCSI Direct Attach FC PLDA standard Devices connected to TL_Ports are registered with the Name Server 2233 Expansion Port E_Ports enable you to expand the fabric by connecting SANbox2 16 switches with other FC SW 2 compliant switches SANbox2 16 switches self discover all inter switch connections Refer to Multiple Chassis Fabrics on page 3 2 for more information about multiple chassis fabrics 59021 05 B 2 7 2 General Description dog Ethernet Port q Simplify U oo oo 202 2 3 Ethernet Port The Ethernet port shown in Figure 2 7 is an RJ 45 connector that provides a connection to a management workstation A management workstation can be a Windows Solaris M workstation or a Linux workstation that is used to configure and manage the switch fabric You can manage the switch over an Ethernet connection using SANbox Manager the Command Line Interface CLI or SNMP RJ 45 Ethernet Port
90. igdata which contains the system configuration information To download this file open an FTP session log in with account name password of images for both and type get configdata cancel Terminates the current configuration edit session without saving changes that were made copy config_source config_destination Copies the configuration given by config_source to the configuration given by config_destination The switch supports up to 10 configurations including the default configuration delete config Deletes the specified configuration file where config is a file name edit config Opens an edit session for the configuration given by config If you omit the configuration name the currently active configuration is used list Displays a list of all available configurations This keyword is available with User authority B 7 B Command Line Interface d tt Config Command Simplify BE oo oR 222 Notes Examples restore Restores configuration settings to an out of band switch from a backup file named configdata which must be first uploaded on the switch using FTP You create the backup file using the Config Backup command Use FTP to load the backup file on a switch then enter the Config Restore command Note Configuration archive files created with the SANbox Manager Archive function are not compatible with the Config Restore command save config Saves changes made during a
91. implify Installing a Switch E oo 4 1 3 Environmental Conditions Consider the factors that affect the climate in your facility such as equipment heat dissipation and ventilation The switch requires the following operating conditions Operating temperature range 10 to 40 C 50 104 F H Relative humidity 25 80 non condensing 4 2 Installing a Switch Unpack the switch and accessories The SANbox2 16 product is shipped with the components shown in Figure 4 1 H SANbox2 16 Fibre Channel Switch 1 with firmware installed Power cords 2 Rubber feet 4 Rack mount brackets 2 CD containing the SANbox Manager switch management application release notes and documentation Figure 4 1 SANbox2 16 Fibre Channel Switch 4 2 59021 05 B 4 Installation Installing a Switch a WEE Installing a SANbox2 16 switch involves the following steps D no oa ND 4 2 1 Mount the Switch Mount the switch Install SFP transceivers Connect the switch to the AC power source Connect the management workstation to the switch Install the SANbox Manager application Configure the switch Configure the ports Cable devices to the switch The switch can be placed on a flat surface and stacked or mounted in a 19 EIA rack The top of each chassis has dimples to receive the rubber feet of a second chassis stacked on top Without the rubber feet the switch occupies 1U of space in a
92. in start SANbox2 admin gt config edit SANbox2 admin config gt set config threshold 59021 05 B B 31 B Command Line Interface Ha Set Config Command implify a lt V TV A list of attributes with formatting and current values will follow Enter a new value or simply press the ENTER key to accept the current value If you wish to terminate this process before reaching the end of the list press q or Q and the ENTER key to do so ThresholdMonitoringEnabled True False True CRCErrorsMonitoringEnabled True False True RisingTrigger decimal value 1 1000 251 FallingTrigger decimal value 0 1000 SampleWindow decimal value 1 1000 sec 0 DecodeErrorsMonitoringEnabled True False True RisingTrigger decimal value 1 1000 200 FallingTrigger decimal value 0 1000 0 SampleWindow decimal value 1 1000 sec 10 ISLMonitoringEnabled True False True RisingTrigger decimal value 1 1000 Ze FallingTrigger decimal value 0 1000 0 SampleWindow decimal value 1 1000 sec 0 LoginMonitoringEnabled True False True RisingTrigger decimal value 1 1000 5 FallingTrigger decimal value 0 1000 SampleWindow decimal value 1 1000 sec 0 LogoutMonitoringEnabled True False True RisingTrigger decimal value 1 1000 5 FallingTrigger decimal value 0 1000 SampleWindow decimal value 1 1000 sec 0 LOSMonitoringEnabled True False True RisingTrigger decimal value
93. inframe Displays continuous performance data in frames second received for all ports Type q and press the Enter key to stop the display outframe Displays continuous performance data in frames second transmitted for all ports Type q and press the Enter key to stop the display errors Displays continuous error counts for all ports Type q and press the Enter key to stop the display 59021 05 B d tt B Command Line Interface Simplify Show Perf Command SE Examples The following is an example of the Show Perf command SANbox2 gt show perf Port Bytes s Bytes s Bytes s Frames s Frames s Frames s Number in out total in out total 0 0 0 0 0 0 0 1 D D D 0 0 0 2 0 0 0 0 0 0 3 0 0 0 0 0 0 4 0 0 0 0 0 0 5 0 0 0 0 0 0 6 0 0 0 0 0 0 7 0 0 0 0 0 0 8 TK 136M 136M 245 68K 68K 9 58K 0 58K 1K 0 1K LO 0 0 0 0 0 0 11 0 0 0 0 0 0 12 0 0 0 0 0 0 13 0 0 0 0 0 0 14 0 TK TK 0 245 245 15 136M 58K 136M 68K 1K 70K The following is an example of the Show Perf Byte command SANbox2 gt show perf byte Displaying bytes sec total Press q and the ENTER key to stop display 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 5 0 0 0 0 0 0 0 0 137M 58 0 0 0 0 8 37M 0 0 0 0 0 0 0 0 136M 58 0 0 0 0 8 36M 0 0 0 0 0 0 0 0 135M 58 0 0 0 0 7 35M 0 0 0 0 0 0 0 0 137M 58 0 0 0 0 8 37M 0 0 0 0 0 0 0 0 136M 58 0 0 0 0 7 36M 0 0 0 0 0 0 0 0 137M 58 0 0 0 0 8 37M 0 0 0 0 0 0 0 0 136M 58 0 0 0 0 8 36M 0 0 0
94. ings enter those as well Choose the OK button Set the date and time Double click on the switch in the topology display In the faceplate display open the Switch menu and select Set Date Time Enter the date and time in the Switch Date and Time window and choose the OK button Reset the switch when prompted to implement the new and date and time Repeat this process for each switch in the fabric then connect the switches 59021 05 B 4 Installation Zeg Installing a Switch Simplify ee 4 2 13 Configure the Ports 4 2 14 Configuring a port involves defining the port mode For public devices and other switches a switch automatically sets the port mode as each port discovers the type of device to which it is connected The default port mode is GL_Port A GL_Port will self configure as an FL_Port when connected to a loop of public devices or an F_Port when connected to a single device AG Port will self configure as an F_Port when connected to a single public device Both GL_Ports and G_Ports self configure as E_Ports when connected to another switch Refer to the SANbox2 8c 16 Switch Management User s Guide for more information about configuring ports You can also configure ports using the CLI Refer to Appendix B Command Line Interface for more information Cable Devices to the Switch 4 16 Connect cables to the SFP transceivers and their corresponding devices and then energize the devices Device host bus adapters ca
95. insert the SANbox2 Installation Disk into the management workstation CD ROM drive Using Windows Explorer double click the drive letter which contains the SANbox2 Installation Disk Double click the SANbox_Manager folder then double click the Windows folder Double click the executable file and follow the SANbox Manager installation instructions SANbox2 Installation Disk Linux Installation To install the SANbox Manager application on Linux from the SANbox2 Installation Disk do the following 1 4 2 11 Close all programs currently running and insert the SANbox2 Installation Disk into the management workstation CD ROM drive Open the File Manager and double click on the CD ROM icon Double click the SANbox_Manager folder then double click the Linux folder Double click the executable file and follow the SANbox Manager installation instructions SANbox2 Installation Disk Solaris Installation To install the SANbox Manager application on Solaris from the SANbox2 Installation Disk do the following 1 4 14 Close all programs currently running and insert the SANbox2 Installation Disk into the management workstation CD ROM drive Open a terminal window If the disk isn t already mounted enter the following command mount mnt cdrom Move the directory on the disk that contains the executable Enter the following command cd cdrom cdrom0 sanbox 1 solaris Run the executable and follow the SANbox Manager
96. itch to AC Power 4 5 Connect the Management Workstation to the Switch 4 8 Ethernet Connection a i a EES 4 9 Serial Connection 4 9 Install SANDOX Manager role oil ai 4 10 SANsurfer Management Suite Disk Windows Installation 4 11 SANsurfer Management Suite Disk Linux Installation 4 12 SANsurfer Management Suite Disk Solaris Installation 4 13 SANbox2 Installation Disk Windows Installation ooo 4 14 SANbox2 Installation Disk Linux Installation reenn 4 14 SANbox2 Installation Disk Solaris Installation oo 4 14 Configure SWILCH SE EE 4 15 Configure the POMS ui a 4 16 Cable Devices to the Switch 4 16 Install Firmwares sea ann een 4 17 Using SANbox Manager to Install Firmware 4 17 Using the CLI to Install Firmware nenne 4 18 Using FTP and the CLI to Install Fimmware 4 19 Powering Down a OWEN ota east 4 20 Diagnostics Troubleshooting POSTIDICONO SOS EE EE 5 1 Heartbeat LED Blink Pattems nennen 5 1 Normal all past tati nase artes 5 1 Maintenance Mode Pattern nt 5 2 Internal Firmware Failure Blink Pattern nn 5 2 Fatal Error Blink Pattern nn nennen nenn 5 2 Configuration File System Error Blink Pattern n 5 2 Logged In LED Indications are een 5 5 ER AOIR G EE Le EE 5 6 Excessive Port Errors cannes een 5 7 Chassis Di
97. ks of their respective owners Document Revision History Revision A Release March 2003 Revision B Update April 2003 Change Affected Section Remove support for initiator devices on TL_Ports Ping command Begin and Stop keywords added to Admin command New date and time effective immediately Device scan enable Force offline RSCN SNMP proxy enable Trap formating using SNMP versions 1 or 2 Add board serial number to Show Setup System display 3 1 B 3 B 16 B 4 B 9 B 20 B 27 B 20 B 27 B 22 B 39 2 7 B 22 B 38 B 60 2000 2003 QLogic Corporation First Printed May 2001 All Rights Reserved Worldwide Printed in U S A QLogic Corporation 6321 Bury Drive Eden Prairie MN 55346 800 342 7379 or 952 932 4000 Page ii 59021 05 B Section 1 1 1 1 2 1 3 1 4 1 5 1 6 1 6 1 1 6 2 1 6 3 1 6 4 1 6 5 1 6 6 1 7 1 8 1 9 1 10 1 11 1 12 1 12 1 1 12 2 1 12 3 Section 2 2 1 2 1 1 2 1 2 2 1 3 2 1 3 1 2 1 3 2 2 1 3 3 2 1 3 4 2 2 2 2 1 59021 05 B Table of Contents Introduction intended Audience u rastas ehe ke 1 1 Related Materials sisi 1 2 Safety Notices Ee E Stee 1 3 ele Ee e EE 1 3 Notes informatives relatives lae curte nenn 1 3 Communications Giatements nennen 1 4 Federal Communications Commission FCC Class A Statement 1 4 Canadian Department of Communications Class A Compliance Statement ccoo ai ee EA lee 1 4 Avis de c
98. kstation without an FTP server you must open an FTP session through the switch to load the image file then open a Telnet session to unpack it with the CLI Image command Refer to Using FTP and the CLI to Install Firmware on page 4 19 4 3 1 Using SANbox Manager to Install Firmware To install firmware using SANbox Manager do the following 1 From the Faceplate display open the Switch menu and select Load Firmware 2 In the Firmware Upload window browse and select the firmware file you want to load 3 In the Firmware Upload window choose the Start button to begin the loading process When the firmware is finished loading the Bytes Transferred field displays the number of bytes that have been transferred Choose the Close button to close the Firmware Upload window Open the Switch menu and select Reset Switch to activate the new firmware 59021 05 B 4 17 Install Firmware 4 Installation d tt Simplify ee 4 3 2 Using the CLI to Install Firmware To install firmware using the CLI when an FTP server is present on the management workstation do the following 1 Connect to the switch through the Ethernet or the serial port and open a Telnet session 2 Enter the following account name and password SANbox2 Login admin Password password 3 To start an admin session enter the following cli gt admin start 4 Retrieve the firmware file The device on which the firmware file is stored must be run
99. l H To run an external loopback test insert a loopback plug into the SFP on the selected port then enter the following command test x external 4 A series of test parameters are displayed on the screen Press the Enter key to accept each default parameter value or type a new value for each parameter and press the Enter key The TestLength parameter is the number of frames sent the FrameSize 256 byte maximum in some cases parameter is the number of bytes in each frame and the DataPattern parameter is the pattern in the payload 5 After the test type has been chosen and the command executed a message on the screen will appear detailing the test results 6 After the test is run put the port back into online state by entering the following command x port number and pressing the Enter key set port x state online 7 To verify port is back online enter the following command and press the Enter key The contents of the AdminState field should display be Online show port x The online loopback node to node test can test only one port at a time and that port must be online and connected to a remote device To run the online loopback test do the following 1 To start an admin session enter the following command and press the Enter key admin start 2 Torun the online loopback test enter the following command and press the Enter key test port x online B 64 59021 05 B d tt B Command Line Interface
100. l To 16 A Per Phase Class A E EN61000 3 3 1995 Limitation Of Voltage Fluctuations And Flicker In Low Voltage Supply Systems For Equipment With Rated Current Less Than Or Equal To 16 A 59021 05 B 1 5 1 Introduction gi q Simplify Communications Statements U oo 2 1 6 5 VCCI Class A Statement CORRI Mamme SENSE EHE VCCI DEE EOS VIR A MERO CT CORE AREA CHAT S CBR WBC SROTCEMHVED COBRAN REANUDAR RAS SLIBRKANSTEMHBOVET This is a Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment VCCI If this equipment is used in a domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions 1 6 6 BSMI Class A Statement LARA E ee AE AA ETA EA T A Se atk AMA ENTE Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user will be required to take adequate measures 1 6 59021 05 B gi 1 Introduction g Simplify Laser Safety Information SE 1 7 Laser Safety Information This product may use Class 1 laser optical transceivers to communicate over the fiber optic conductors The U S Department of Health and Human Services DHHS does not consider Class 1 lasers to be hazardous The International Electrotechnical Commission IEC 825 Laser Safety Standard requires labeling in Eng
101. lease the tension then pull on the release tab or lever and remove the transceiver Different transceiver manufacturers have different release mechanisms Consult the documentation for your transceiver To install insert the transceiver into the port and gently press until it snaps in place as shown in Figure 6 1 Note The SFP transceiver will fit only one way If the SFP does not install under gentle pressure flip it over and try again Figure 6 1 SFP Transceiver Installation 6 2 59021 05 B d tt 6 Removal Replacement Simplify Power Supplies ZZZ 13 7 105 6 2 Power Supplies The power supplies are hot pluggable This means you can remove or install one of the power supplies while the switch is operating without disrupting service The power supplies are also interchangeable that is the left and right power supplies are the same unit To remove the power supply grasp the power supply latch handle and pull firmly to release the latches and disengage the modular connector Slide the power supply out of its bay as shown in Figure 6 2 To install a power supply slide the power supply into the bay with the latch handle on top Press the power supply firmly into place until it is fully seated then push the latch handle in against the power supply to engage the latches Latch Handle Figure 6 2 Power Supply Removal 59021 05 B 6 3 6 Removal Replacement d tt Fans Simplify
102. liche Hochspannung an den Metallteilen des switch Geh uses verursachen Der Kunde tr gt die Verantwortung f r eine vorschriftsm ige Verdrahtung und Erdung der Steckdose zur Vermeidung eines elektrischen Schlages In manchen L ndern ist eventuell die Verwendung eines anderen Kabels erforderlich da der Stecker des mitgelieferten Kabels nicht in die landes blichen Steckdosen pa t In diesem Fall m ssen Sie sich ein Kabel besorgen da die folgenden Anforderungen erf llt m F r 125 Volt Netze 10 Ampere Kabel mit UL und CSA Zulassung m Fur 250 Volt Netze 10 Ampere Kabel gem den Anforderungen der HO5VV F und VDE SEMKO und DEMKO Zulassung To connect the switch to an AC power source and energize the switch do the following 1 Connect the power cords to the AC power receptacles on the front of the switch chassis 2 Connect each power cord to a 3 wire grounded AC outlet that delivers power in accordance with the power requirements in Appendix A Specifications Note To provide redundancy in the event of an AC power circuit failure connect the switch power supplies to separate AC circuits 3 Place one or both power On Off switches in the On position to energize the switch logic circuitry Confirm that the Input Power LED on the switch chassis is illuminated indicating that the switch logic circuitry is receiving DC voltage If not contact your authorized maintenance provider 4 6 59021 05 B gi 4 Install
103. lish German Finnish and French stating that the product uses Class 1 lasers Because it is impractical to label the transceivers the following label is provided in this manual CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A LASER DE CLASSE 1 TO IEC 825 1984 CENELEC HD 482 S1 1 8 Electrostatic Discharge Sensitivity ESDS Precautions The assemblies used in the switch chassis are ESD sensitive Observe ESD handling procedures when handling any assembly used in the switch chassis 59021 05 B 1 7 1 Introduction dog q Simplify Accessible Parts E ee 1 9 Accessible Parts The only Field Replaceable Units FRUs in the SANbox2 16 switch are E Small Form Factor Pluggable SFP optical transceivers n Power supplies n Fans Refer to Section 6 Removal Replacement for more information 1 10 Pi ces Accessibles Les pi ces remplacables Field Replaceable Units FRU du commutateur SANbox2 16 Fibre Channel Switch sont les suivantes Interfaces aux media d interconnexion appel s SFP transceivers m Alimentation s de courant M Ventilateurs Se reporter la Section 6 Proc dures de retrait et remplacement pour plus de renseignements 1 11 Zug ngliche Teile Nur die folgenden Teile im SANbox2 16 Fibre Channel Switch k nnen kundenseitig ersetzt werden H Schnittstellen f r die Zwischenverbindungstr ger SFP transceivers genannt m Netzteil e u Geh usel fte Weitere Informatione
104. livered to the switch logic circuitry Refer to Section 6 Removal Replacement for information about replacing a power supply Over Temperature LED Output Power LED Amber Green av AC Power On Off Switch Receptacle Figure 2 9 Power Supply Components 59021 05 B 2 9 2 General Description d tt Simplify Fans U e e e 222 Each power supply is capable of providing all of the switch s power needs During normal operation each power supply provides half of the demand If one power supply goes offline the second power supply steps up and provides the difference The power supplies are hot swappable and interchangeable Hot swappable means that you can remove and replace one power supply while the switch is in operation without disrupting service Each power supply has two status LEDs an Output Power LED green and an Over Temperature LED amber The Output Power LED illuminates to indicate that the power supply is producing DC voltage at the proper levels The Over Temperature LED illuminates to indicate that the power supply is overheating When a power supply overheats the switch extinguishes the Output Power LED and shuts down the power supply Refer to Section 5 Diagnostics Troubleshooting for informati
105. ll Form Factor Pluggable SFP Transceivers An SFP transceiver like the one shown in Figure 2 5 converts electrical signals to and from optical laser signals to transmit and receive data SFP transceivers plug into the ports duplex fiber optic cables plug into the transceivers which then connect to the devices A port is capable of transmitting at 1 Gbps or 2 Gbps however the transceiver must be capable of 2 Gbps for the port to deliver at that rate d tt 2 General Description Simplify The SFP transceivers are hot swappable This means that you can remove or install an SFP transceiver while the switch is operating without harming the switch or the transceiver However communication with the connected device will be interrupted Refer to Section 6 Removal Replacement for information about installing and removing SFP optical transceivers Figure 2 5 SFP Transceiver 2 2 2 Port LEDs Each data port has its own Logged In LED and Activity LED as shown in Figure 2 6 The Logged In LED indicates whether the port and its connected device are logged into the fabric or if it is connected to another switch and they are segmented The Activity LED indicates the frequency at which the port receives or transmits frames Logged In LED Activity LED Green Amber SAS Figure 2 6 Port LEDs 59021 05 B 2 5 2 General Description dog Fibre Channel Ports q Sim
106. login session To log in again enter the maintenance mode account name and password prom prom 5 3 2 Maintenance Image Unpack This option unpacks and installs new firmware when the current firmware has become corrupt Before using this option you must load the new firmware image file onto the switch The steps to install new firmware using this option are as follows 1 Place the switch in maintenance mode Refer to the procedure for maintenance mode in Recovering a Switch on page 5 12 2 Use FTP to load a new firmware image file onto the switch Refer to Using FTP and the CLI to Install Firmware on page 4 19 Do not unpack the firmware image file with the Image command 3 Select option 1 from the maintenance menu When prompted for a file name prompt enter the firmware image file name Image filename filename Unpacking filename please wait Unpackage successful 4 Select option 7 to reset the switch and exit maintenance mode 59021 05 B 5 13 5 Diagnostics Troubleshooting d tt Recovering a Switch Simplify BE q 02 5 3 3 Maintenance Reset Network Config This option resets the network properties to the factory default values and saves them on the switch Refer to Table B 6 for the default network configuration values 5 3 4 Maintenance Reset Password File This option restores the password for the Admin account name to the default password and removes all other user
107. lows the switch to operate but disables the ports that have errors Whether the problem is fatal or non fatal contact your authorized maintenance provider If there are no errors the Heartbeat LED blinks at a steady rate of once per second If a fatal error occurs the Heartbeat LED will show an error blink pattern If there are non fatal errors the switch disables the failed ports and flashes the associated Logged In LEDs Refer to Heartbeat LED Blink Patterns on page 5 1 for more information about Heartbeat LED blink patterns Heartbeat LED Blink Patterns 5 1 1 1 Normal all pass 59021 05 B If all POST diagnostics pass the switch will go to normal operation and the Heartbeat LED will blink at a steady rate of one 1 blink per second 5 1 POST Diagnostics Simplify IS _ _ __ 5 Diagnostics Troubleshooting d tt 5 1 1 2 Maintenance Mode Pattern Steady illumination indicates that the switch is in maintenance mode which returns the switch IP address to 10 0 0 1 From maintenance mode you may reload firmware reset the password to the factory default and remove a corrupt configuration 5 1 1 3 Internal Firmware Failure Blink Pattern An internal firmware failure blink pattern is 2 blinks per second followed by a two second pause The 2 blink error pattern indicates that the firmware has failed and that the switch must be reset Power cycle the switch to reset it 1 second 2 seconds lt l
108. lt values zoning Clears the zoning database and deactivates the active zone set The zoning configuration values autosave default visibility remain unchanged The following tables specify the various factory default settings Reset Command Simplify B Command Line Interface d tt E anane ee Table B 2 Switch Configuration Defaults Parameter Default Admin State Online Broadcast Enabled True InbandEnabled True Domain ID 1 Domain ID Lock False Symbolic Name SANbox2 R_T_TOV 100 R_A_TOV 10000 E D TOV 2000 FS_TOV 5000 DS TOM 5000 Principal Priority 254 Configuration Description Undefined Configuration Last Saved By Initial Configuration Last Saved On Initial Table B 3 Port Configuration Defaults Parameter Default Admin State Online Link Speed Auto Port Type GL ISL Security Any Symbolic Name Port ALFairness False DeviceScanEnabled True ForceOfflineRSCN False ARB_FF False B 20 59021 05 B Simplify Reset Command d tt B Command Line Interface SE Table B 3 Port Configuration Defaults Continued Parameter Default InteropCredit 0 ExtCredit 0 FANEnable True LCFEnable False MFSEnable True MFS_TOV 10 MSEnable True NoClose False IOStreamGuard Disabled VIEnable False CheckAlps False Table B 4 Alarm Threshold Configuration Defaults Parameter Default ThresholdMonitoringEnabled False CRCErrorsMonitoringEnabled True RisingTrigger 2
109. m and disables the affected port changing its operational state to down Port errors can be caused by the following m Thresholds are too low or the sample interval is too small H Faulty Fibre Channel port cable H Faulty SFP NW Faulty port H Fault device or HBA Review the alarm log to determine if excessive port errors are responsible for disabling the port Look for a message that mentions one of the monitored error types indicating that the port has been disabled then do the following 1 Examine the alarm configuration for the associated error using the Show Config Threshold command or the SANbox Manager application Refer to the Show Config Command on page B 53 Refer to Table B 4 for a list of the alarm configuration defaults Are the thresholds and sample interval correct m Yes Continue Lal No Correct the alarm configuration Ifthe condition remains continue 59021 05 B 5 7 5 Diagnostics Troubleshooting pg POST Diagnostics q Simplify U ooo ooo o 2 Reset the port then perform an external port loopback test to validate the port and the SFP Refer to the Test Command on page B 63 or the SANbox2 8c 16 Switch Management User s Guide for information about testing ports Does the port pass the test Yes Continue H No Replace the SFP and repeat the test If the port does not pass the test contact your authorized maintenance provider Otherwise continue 3 Replace the Fibre Channel port ca
110. n SymbolicName SANbox2 203 SwitchWWN 10 00 00 c0 dd 00 b8 b5 SwitchType SANbox2 16 PromVersion V0 1 5 18 day month date time year CreditPool 0 DomainID 3 FirstPortAddress 640000 FlashSize MBytes 128 LogLevel Info MaxPorts 16 NumberOfResets 127 ReasonForLastReset NormalReset SwImageVersion 1 build date V1 5 6 16 day month date time year SwImageVersion 2 build date V1 5 6 18 day month date time year ActiveConfiguration default ActiveSWImage 2 AdminState Online AdminModeActive False BeaconOnStatus False OperationalState Online PrincipalSwitchRole False BoardTemp 1 Degrees Celsius 32 BoardTemp 2 Degrees Celsius 36 SwitchDiagnosticsStatus Passed SwitchTemperatureStatus Normal The following is an example ofthe Show Topology command SANbox2 gt show topology Unique ID Key A ALPA D Domain ID P Port ID Port Local Local Remote Remote Unique Number Type PortWWN Type NodeWWN ID 5 F 20 05 00 c0 dd 00 bd ec N 20 00 00 00 c9 22 1e 93 010500 P 10 E 20 0a 00 c0 dd 00 bd ec E 10 00 00 c0 dd 00 80 21 4 0x4 D 59021 05 B B 51 Show Command Simplify B Command Line Interface d tt RES oo The following is an example of the Show Topology command for port 4 SANbox2 gt show topology 4 Local Link Information PortNumber 4 PortID 010400 PortWWN 20 04 00 c0 dd 00 90 3 PortType F Remote Link Information Device 0 PortID 010400 PortWWN 21 00 00 e0 8b 07 a8 bc No
111. n ElA rack Mounting rails are required and available through QLogic Corporation WARNING CAUTION 59021 05 B Mount switches in the rack so that the weight is distributed evenly An unevenly loaded rack can become unstable possibly resulting in equipment damage or personal injury If the switch is mounted in a closed or multi unit rack assembly make sure that the operating temperature inside the rack enclosure does not exceed the maximum rated ambient temperature Refer to Switch Environmental on page A 4 The switch must rest on rails or a shelf in the rack or cabinet Allow 16 cm 6 5 in minimum clearance at the front and rear of the rack for service access and ventilation Do not restrict chassis air flow Allow 16 cm 6 5 in minimum clearance at the front and rear of the rack for service access and ventilation Multiple rack mounted units connected to the AC supply circuit may overload that circuit or overload the AC supply wiring Consider the power source capacity and the total power usage of all switches on the circuit Refer to Switch Electrical on page A 3 Reliable grounding in the rack must be maintained from the switch chassis to the AC power source 4 3 4 Installation gi q Simplify Installing a Switch Ensure that the19 inch rack meets the following standard specifications E ANSI EIA RS 230 Standard entitled Cabinets Racks Panels and Associated Equipment n MIL STD 189 entitled Ra
112. n finden Sie im Abshcnitt 6 Ausbauen der ersetzbaren Teile 1 8 59021 05 B Technical Support SE 1 12 Technical Support Customers should contact their authorized maintenance provider for technical support of their QLogic switch products QLogic direct customers may contact QLogic Technical Support others will be redirected to their authorized maintenance provider fog 1 Introduction g Simplify Visit the QLogic switch support Web site listed in Contact Information for the latest firmware and software updates 1 12 1 Availability QLogic Technical Support is available from 7 00 AM to 7 00 PM Central Standard Time Monday through Friday excluding QLogic observed holidays 1 12 2 Training QLogic offers the following technical training courses BM Switch Certification a HBA Certification Each course is available at the training facility in Eden Prairie MN or at your local facility All courses include a Fibre Channel overview and sections on installation maintenance and topology solutions Each student receives a set of manuals and a CD ROM containing course training materials Upon successful completion of the training Qlogic awards a certificate identifying the student as a Certified SANbox or SANblade Professional 1 12 3 Contact Information Address QLogic Switch Products Inc 6321 Bury Drive Eden Prairie Minnesota 55346 USA Telephone 1 952 932 4040 Fax 1 952 932 4018 Email Technical Service
113. n have SFP or SFF transceivers or GigaBit Interface Converters GBIC LC type duplex fiber optic cable connectors are designed for SFP transceivers while SC type connectors are designed for GBICs Duplex cable connectors are keyed to ensure proper orientation Choose the fiber optic cable with the connector combination that matches the device host bus adapter 59021 05 B gi 4 Installation q Simplify Install Firmware ls 4 3 Install Firmware The switch comes with current firmware installed You can upgrade the firmware from the management workstation as new firmware becomes available Firmware installation involves loading the firmware image file onto the switch unpacking the image file and then resetting the switch to activate the new firmware New firmware can be loaded on the switch while the switch is operating without disrupting service However you must reset the switch to activate the new firmware which does disrupt service You can use the SANbox Manager application or the CLI to install new firmware m The SANbox Manager application loads and unpacks the firmware image file in one operation Refer to Using SANbox Manager to Install Firmware on page 4 17 RH When using the CLI on a workstation that has an FTP server you can open a Telnet session and load and unpack the firmware image file using the CLI Image command Refer to Using the CLI to Install Firmware on page 4 18 RH When using the CLI on a wor
114. nd Authority Syntax Keywords Notes 59021 05 B Resets the switch configuration parameters Admin reset config config_name factory port port_number snmp switch default system zoning config config_name Resets the configuration given by config_name to the factory default values for switch port alarm threshold and zoning configuration This keyword clears all zoning definitions If config_name does not exist on the switch a configuration with that name will be created If you omit config_name the active configuration is reset You must activate the configuration or reset the switch for the changes to take effect Refer to Table B 2 through Table B 4 for switch port and alarm threshold configuration default values factory Resets switch alarm threshold zoning SNMP zoning configuration and system configuration settings to the factory default values The switch configuration is activated automatically Refer to Table B 2 through Table B 6 port port_number Reinitializes the port given by port_number Ports are numbered beginning with 0 snmp Resets the SNMP configuration settings to the factory default values Refer to Table B 5 for SNMP configuration default values switch Reinitializes the switch This is the default This command also closes the Telnet session system Resets the system configuration settings to the factory default values Refer to Table B 6 for system configuration defau
115. neRSCN False ARB_FF False InteropCredit 0 ExtCredit 0 FANEnable False LCFEnable False MFSEnable False MFS_TOV 640 MSEnable False B 53 Show Config Command Simplify B Command Line Interface d tt ns ooo oo NoClose False IOStreamGuard False VIEnable False CheckAlps False The following is an example of the Show Config Switch command SANbox2 gt show config switch Configuration Name default AdminState Online BroadcastEnabled True InbandEnabled True DomainID 100 0x64 DomainIDLock False SymbolicName SANbox2 N_11 107 R_T_TOV 100 R_A_TOV 10000 E_D_TOV 2000 FS_TOV 5000 DS_TOV 5000 PrincipalPriority 254 ConfigDescription QLogic SANbox2 FC Switch ConfigLastSavedBy guest IB session10 ConfigLastSavedOn day month date time year The following is an example of the Show Config Threshold command SANbox2 gt show config threshold Configuration Name default ThresholdMonitoringEnabled True CRCErrorsMonitoringEnabled True RisingTrigger 25 FallingTrigger 1 SampleWindow 10 DecodeErrorsMonitoringEnabled True RisingTrigger 25 B 54 59021 05 B d tt B Command Line Interface Simplify Show Config Command SE FallingTrigger 0 SampleWindow 10 ISLMonitoringEnabled True RisingTrigger 2 FallingTrigger 0 SampleWindow 10 LoginMonitoringEnabled True RisingTrigger 5 FallingTrigger 1 SampleWindow 10 LogoutMonitoringEnabled True RisingTrigger 5 FallingTrigger 1 SampleWindow 10 LO
116. ning an FTP server Enter the following command to retrieve the firmware file from the specified IP address cli admin gt image fetch username 10 0 0 254 firmwarefilenametoload firmwarefilenameonswitch Connected to 10 0 0 254 Note If prompted for your password enter your password for that IP Address and press the Enter key 331 Password required for username Password 230 User username logged in bin 200 Type set to I verbose Verbose mode off 5 Enter the following command to display the list of firmware files cli admin gt image list 6 Enter the following command to install the new firmware cli admin gt image unpack firmwarefilenameonswitch 7 Reset the switch to activate the new firmware cli admin gt reset 4 18 59021 05 B Install Firmware df 4 Installation a x 4 3 3 Using FTP and the CLI to Install Firmware To install firmware using the CLI when the management workstation does not have an FTP server do the following 1 Connect to the switch through the Ethernet or the serial port 2 Move to the folder or directory that contains the new firmware image file 3 Establish communications with the switch using the File Transfer Protocol FTP Enter one of the following on the command line gt ftp XXX XXX XXX XXX or gt ftp switchname where xxx xxx xxx xxx is the switch IP address and switchname is the switch name associated with the
117. ning the same version of firmware B Command Line Interface d tt Lip Command Simplify ee Lip Command Reinitializes the specified loop port Authority Admin Syntax lip port_number Keywords port_number The number of the port to be reinitialized Examples The following is an example of the Lip command SANbox2 admin gt lip 2 B 14 59021 05 B d tt B Command Line Interface Simplify Passwd Command SE Passwd Command Changes a user account s password Authority Admin to change another account s password User to change your own Syntax passwd account_name Keywords account_name The user account name You must open an admin session to change the password for an account name other than your own If you omit account_name you will be prompted to change the password for the current account name Examples The following is an example of the Passwd command SANbox2 admin gt passwd user H Press q and the ENTER key to abort this command account OLD password account NEW password 4 20 chars please confirm account NEW password password has been changed 59021 05 B B 15 Ping Command B Command Line Interface d tt Simplify ee Ping Command Authority Syntax Keywords Examples Initiates an attempt to communicate with another switch in the fabric and reports the result User ping ip_address ip_address The IP address of the switch to query
118. o change configuration parameters for the port number given by port_number If you omit port_number the system begins with port O and proceeds in order through the last port For each parameter enter a new value or press the Enter key to accept the current value shown in brackets Enter q to cancel the configuration for one port or qq to cancel the configuration for all ports Table B 7 describes the port parameters ports port_number Initiates an editing session in which to change configuration parameters for all ports based on the configuration for the port given by port_number If you omit port_number port 0 is used For each parameter enter a new value or press the Enter key to accept the current value shown in brackets Enter q to cancel the configuration Table B 7 describes the port parameters Table B 7 Set Config Port Parameters Parameter Description AdminState Port administrative state online offline diagnostics or down LinkSpeed 1Gb sec 2 Gb sec or Auto PortType Type of port ISL Security E_Port security Determines which switches a port will establish a link with E Any link with any FC SW 2 compliant switch E Ours link only with an FC SW 2 compliant QLogic switch E None reject the link SymbolicPortName Descriptive name ALFairness Arbitration loop fairness Enables True or disables False the switch s priority to arbitrate on the loop 59021 05 B
119. o use the Admin command The Admin Start command opens an admin session which provides access to the commands that change switch and fabric configurations Refer to the Admin Command on page B 4 Note Admin authority is enforced only if fabric security is enabled By default fabric security is disabled Refer to Set Setup Command on page B 38 System keyword for more about setting fabric security The commands and their page numbers are listed by authority level in Table B 1 Table B 1 Commands Listed by Authority Level User Authority Commands Admin Authority Command Help B 11 Admin B 4 History B 12 Ping B 16 Admin Session Commands Ps B 17 ne Quit B 18 Alias B 5 Show B 43 Config B 7 Show Config B 53 Date B 9 Show Log B 56 Fallback B 10 Show Perf B 58 Image B 13 Show Setup B 60 Lip B 14 Uptime B 66 Passwd B 15 Whoami B 69 Reset B 19 Set B 24 Set Config B 26 Set Log B 34 Set Port B 37 Set Setup B 38 Shutdown B 62 Test B 63 User B 67 Zone B 70 Zoneset B 74 Zoning B 77 Some keywords are available with User authority 59021 05 B B 3 Admin Command B Command Line Interface d tt Simplify BE n Admin Command Authority Syntax Keywords Notes Examples Opens and closes an Admin session The Admin session provides commands that change the fabric and switch configurations Only one Admin sessi
120. on about creating user accounts Note A switch supports a combined maximum of 15 logins This includes SANbox Manager inband and out of band logins Application Programming Interface API inband and out of band logins and Telnet logins Of this 15 there can be a combined maximum of 10 SANbox Manager and API logins Additional logins will be refused 59021 05 B B 1 B Command Line Interface d tt Command Syntax Simplify Ce AH amp i amp amp g 7 a jia pa aagaagaaaaa a B 2 Command Syntax The command syntax is as follows command keyword keyword value keyword value 1 value2 The Command is followed by one or more keywords Consider the following rules and conventions E Commands and keywords are lowercase and case sensitive H Commands with keywords require one of those keywords m Required keyword values appear in standard font value Optional values are shown in italics value u Underlined portions of the keyword in the command format indicate the abbreviated form that can be used For example the Delete keyword can be abbreviated Del B 2 59021 05 B Simplify Commands d tt B Command Line Interface SE B 3 Commands The command set provides for User and Admin authority levels RH User authority grants viewing access to the fabric and switches using the Show command and other read only commands RH Admin authority includes the User authority and grants permission t
121. on about troubleshooting over temperature conditions 2 6 Fans The switch is equipped with two fans as shown in Figure 2 10 If one fan should fail the other fan is capable of providing the necessary cooling until the failed fan can be replaced The fans are hot swappable and interchangeable Refer to Fans on page 6 4 for information about removing and replacing the fans Air flow can be front to back or back to front depending on the switch model Fans est CTA a O I af O f EE DI Figure 2 10 Fans 2 10 59021 05 B 2 General Description Switch Management SE 2 7 Switch Management 59021 05 B SANbox Manager is a workstation based Java application that provides a graphical user interface for fabric management This application runs on a Windows Solaris or Linux workstation The management workstation connects to the fabric directly through one switch s Ethernet port and provides in band management for all other switches in the fabric Refer to the SANbox2 8c 16 Switch Management User s Guide fo
122. on can be open on the switch at any time An inactive Admin session will time out after a period of time which can be changed using the Set Setup System command Refer to the Set Setup Command on page B 38 Admin admin start or begin end stop cancel start or begin Opens the admin session end or stop Closes the admin session The Logout Shutdown and Reset Switch commands will also end an admin session cancel Terminates an Admin session opened by another user Use this keyword with care because it terminates the Admin session without warning the other user and without saving pending changes Closing a Telnet window during an admin session does not release the session In this case you must either wait for the admin session to time out or use the Admin Cancel command The following example shows how to open and close an Admin session SANbox2 gt admin start SANbox2 admin gt SANbox2 admin gt admin end 59021 05 B B Command Line Interface Alias Command SE Alias Command Authority Syntax Keywords 59021 05 B Creates a named set of ports devices Aliases make it easier to assign a set of ports devices to many zones An alias can not have a zone or another alias as a member Admin alias add alias members copy alias_source alias_destination create alias delete alias list members alias remove alias members rename alias_old alias_new add alias m
123. onformit aux normes du minist re des Communications du Canada 1 5 CE EE 1 5 VCCI Class A Statement ee nnnnnnne nen 1 6 BSMI Class A Statement Aaa KAA NaS 1 6 Laser Safety Information nee ee dias 1 7 Electrostatic Discharge Sensitivity ESDS Precautions sn 1 7 ACCESS En EE 1 8 PIECESACCESSIDIOS EE 1 8 Z gangliche Teile terre 1 8 Technical Support 1 9 Avallabiliiyc2 A AAA i 1 9 RR le O 1 9 Contact Information ida 1 9 General Description Chassis Controls amd LEDS cerati bat 2 2 Power SWiGhes siasi ilaria 2 2 Maintenance Button ocx riale 2 2 Chassis E 2 3 Over Temperature LED Amber 2 3 Fan Fall LED AMEN u a 2 3 Heartbeat LED Amber eebe malas 2 4 Input Power LED Green ea 2 4 Fibre Channel PONS zes u its 2 4 Small Form Factor Pluggable SFP Transceivers n 2 5 Page iii SANbox2 16 Fibre Channel Switch Installation Guide I F q Ec ooo 2 2 2 2 2 2 1 2 2 2 2 2 2 3 2 2 3 1 2 2 3 2 2 2 3 3 2 3 2 4 2 5 2 6 2 7 Section 3 3 1 3 2 3 2 1 3 2 2 3 2 2 1 3 2 2 2 3 2 2 3 3 3 3 3 1 3 3 2 3 3 3 3 4 3 4 1 3 4 2 3 4 3 3 5 3 6 Section 4 4 1 4 1 1 4 1 2 4 1 3 4 2 4 2 1 4 2 2 Page iv POM eebe eege eebe Ee 2 5 Logged In LED Ara eek 2 6 Activity LEI sascha ke ea times 2 6 AAA Ehe ee 2 6 Fabric PONS tc ea na ohne inte 2 7 Translated Loop Port anioni ia dalai 2 7 Expansion Polti La n 2 7 Ethernet E lille REN LE
124. ontrol List ACL hard zone BM Virtual Private Fabric VPF hard zone 3 8 59021 05 B dt 3 Planning Device Access SE 3 4 1 Soft Zones Soft zoning divides the fabric for purposes of controlling discovery Members of the same soft zone automatically discover and communicate freely with all other members of the same zone The soft zone boundary is not secure traffic across soft zones can occur if addressed correctly The following rules apply to soft zones E Soft zones that include members from multiple switches need not include the ports of the inter switch links m Soft zone boundaries yield to ACL and VPF zone boundaries m Soft zones can overlap that is a port can be a member of more than one soft zone H Membership can be defined by Fibre Channel address domain ID and port ID or worldwide name M Soft zoning supports all port modes 3 4 2 Access Control List Hard Zones Access Control List ACL zoning divides the fabric for purposes of controlling discovery and inbound traffic ACL zoning is a type of hard zoning that is hardware enforced This type of zoning is useful for controlling access to certain devices without totally isolating them from the fabric Members can communicate with each other and transmit outside the ACL zone but cannot receive inbound traffic from outside the zone The following rules apply to ACL zones m The ACL zone boundary is secure against inbound traffic MB ACL zones can overlap tha
125. onverter that is permanently attached to the circuit board Small Form Factor Pluggable A transceiver device smaller than a GigaBit Interface Converter that plugs into the Fibre Channel port SNMP Simple Network Management Protocol Target A storage device that responds to an initiator device VCCI Voluntary Control Council for Interference Worldwide Name WWN A unique 64 bit address assigned to a device by the device manufacturer WWN Worldwide Name 59021 05 B Glossary 3 Simplify Installation Guide d tt SANbox2 16 Fibre Channel Switch E E c oo Notes Glossary 4 59021 05 B Numerics 10 100 Base T straight cable 4 8 A access 3 8 Access Control List zone 3 9 account name B 1 B 69 description 3 11 display B 69 ftp 5 3 maintenance mode 5 12 Activity LED 2 6 Admin authority 3 11 B 3 Admin command B 4 administrative state port B 37 switch B 25 air flow 2 10 A 4 alarm configuration B 29 configuration display B 53 log B 24 B 43 alias add members B 5 copy B 5 create B 5 delete B 5 delete members B 6 display list B 5 display members B 6 rename B 6 Alias command B 5 altitude A 4 Arbitrated Loop Physical Address 3 1 B 37 authority 3 11 B bandwidth 3 7 beacon B 24 59021 05 B Index brackets 4 2 4 4 broadcast B 43 buffer credit 3 6 A 2 cable 10 100 Base T 4 8 10 100 Base T crossover cable 4 8 fibre optic 3 1 null modem F F DB9 4 8 cascade topology 3 3 chassi
126. or and the results of the Power On Self Test POST Following a normal power up the Heartbeat LED blinks about once per second to indicate that the switch passed the POST and that the internal switch processor is running In maintenance mode the Heartbeat LED illuminates continuously Refer to Heartbeat LED Blink Patterns on page 5 1 for more information about Heartbeat LED blink patterns 2 1 3 4 Input Power LED Green The Input Power LED indicates the voltage status at the switch logic circuitry This LED illuminates when the switch logic circuitry is receiving the proper DC voltages 2 2 Fibre Channel Ports Each SANbox2 16 switch has 16 Fibre Channel ports numbered 0 15 as shown in Figure 2 4 Each of these ports is served by a Small Form Factor Pluggable SFP transceiver The port LEDs are located to the right of their respective ports and provide port login and activity status information The ports self discover the proper mode when connected to public devices and other switches You can also configure any port to support a loop of private devices Port Port LEDs Al HI WI BA El RL lc o Bo AO Figure 2 4 Fibre Channel Ports 2 4 59021 05 B Fibre Channel Ports SE 2 2 1 Sma
127. plify C 2 2 2 1 Logged In LED The Logged in LED indicates the logged in or initialization status of the connected devices After successful completion of the POST the switch extinguishes all Logged In LEDs Following a successful loop initialization or port login the switch illuminates the corresponding logged in LED This shows that the port is properly connected and able to communicate with its attached devices The Logged In LED remains illuminated as long as the port is initialized or logged in If the port connection is broken or an error occurs that disables the port the Logged In LED will flash Refer to Logged In LED Indications on page 5 5 for more information about the Logged In LED 2 2 2 2 Activity LED The Activity LED indicates that data is passing through the port Each frame that the port transmits or receives causes this LED to illuminate for 50 milliseconds This makes it possible to observe the transmission of a single frame When extending credits the Activity LED for a donor port will reflect the traffic of the recipient port Refer to Distance on page 3 6 for more information about extended credits and donor ports 2 2 3 Port Modes SANbox2 16 switches support the following port modes H Generic ports GL_Port and G_ Port H Fabrice ports FL_Port and F_Port H Translated loop ports TL Port n Expansion ports E_Port Switches come from the factory with all ports configured as GL_Ports GL_Por
128. ports that are currently transmitting and receiving broadcast frames chassis Displays chassis component status and temperature config option Displays switch and port configuration attributes Refer to the Show Config Command on page B 53 59021 05 B B 43 B Command Line Interface d tt Show Command Simplify e ooo 0202 domains Displays list of each domain and its worldwide name in the fabric donor Displays list of current donor configuration for all ports fabric Displays list of each domain fabric ID worldwide name node IP address and port IP address interface Displays the status of the active network interfaces log option Displays log entries Refer to the Show Log Command on page B 56 Isdb Displays Link State database information mem count Displays information about memory activity for the number of seconds given by count If you omit count the value 1 is used Displayed memory values are in 1K block units Note This keyword will display memory activity updates until count is reached it cannot be interrupted Therefore avoid using large values for count ns option Displays name server information for the specified option If you omit option name server information for the local domain ID is displayed option can have the following values all Displays name server information for all switches and ports domain_id Displays name server information for
129. ption For this reason open a Telnet session and use the Shutdown command to initiate an orderly shut down then power down the switch Refer to the Shutdown Command on page B 62 4 20 59021 05 B Section 5 Diagnostics Troubleshooting Diagnostic information about the switch is available through the chassis LEDs the power supply LEDs and the port LEDs Diagnostic information is also available through the SANbox Manager and CLI event logs and error displays This section describes two types of diagnostics Power On Self Test POST and chassis POST diagnostics describe the Heartbeat LED and the port Logged In LED indications Chassis diagnostics cover power supply and fan diagnostics as well as over temperature conditions This section also describes how to use maintenance mode to recover a disabled switch 5 1 POST Diagnostics 5 1 1 The switch performs a series of Power On Self Tests POST as part of its power up procedure The POST diagnostic program performs the following tests EH Checksum tests on the boot firmware in PROM and the switch firmware in flash memory M Internal data loopback test on all ports m Access and integrity test on the ASIC During the POST the switch logs any errors encountered Some POST errors are fatal others are non fatal The switch uses the Heartbeat LED and the Logged In LED to indicate switch and port status A fatal error disables the switch so that it will not operate A non fatal error al
130. r information about the SANbox Manager application and its use In addition to SANbox Manager the switch supports the following management tools H Command Line Interface m File Transfer Protocol FTP m Simple Network Management Protocol SNMP The command line interface provides monitoring and configuration functions by which the administrator can manage the fabric and its switches Refer to Appendix B Command Line Interface for more information FTP provides the command line interface for exchanging files between the switch and the management workstation These files include firmware image files configuration files and log files SNMP provides monitoring and trap functions for the fabric SANbox2 firmware supports SNMP versions 1 and 2 the Fibre Alliance Management Information Base FA MIB version 4 0 and the Fabric Element Management Information Base FE MIB RFC 2837 Traps can be formatted using SNMP versions 1 or 2 2 11 2 General Description og Switch Management q Simplify u UTS Notes 2 12 59021 05 B 3 1 Devices 59021 05 B Section 3 Planning Consider the following when planning a fabric Devices Multiple chassis fabrics Performance Device access Fabric management Fabric security When planning a fabric consider the number of devices and the anticipated demand This will determine the number of ports that are needed and in turn the number of switches Consider how m
131. r les causes 1 6 4 CE Statement The CE symbol on the equipment indicates that this system complies with the EMC Electromagnetic Compatibility directive of the European Community 89 336 EEC and to the Low Voltage Safety Directive 73 23 EEC Such marking indicates that this system meets or exceeds the following technical standards m EN60950 A11 1997 Safety of Information Technology Equipment Including Electrical Business Equipment u EN60825 1 A11 1996 Safety of Laser Products Part 1 mM EN55022 1998 Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment mM EN55024 1 1998 Electromagnetic compatibility Generic immunity standard Part 1 Residential commercial and light industry m 1EC1000 4 2 1995 Electrostatic Discharge Immunity Test M 1EC1000 4 3 1995 Radiated Radio Frequency Electromagnetic Field Immunity Test M 1EC1000 4 4 1995 Electrical Fast Transient Burst Immunity Test M 1EC1000 4 5 1995 Surge Immunity Test M 1EC1000 4 6 1996 Immunity To Conducted Disturbances Induced By Radio Frequency Fields M 1EC1000 4 8 1993 Power Frequency Magnetic Field Immunity Test a IEC1000 4 11 1994 Voltage Dips Short Interruptions And Voltage Variations Immunity Tests a EN61000 3 2 1995 Limits For Harmonic Current Emissions Equipment Input Current Less Than Equa
132. r web browser to view the Start_Here htm document using one of the following commands mozilla file mnt cdrom Start_Here htm or netscape file mnt cdrom Start_Here htm d The SANsurfer Management Suite start page opens in your default browser On the SANsurfer Management Suite start page choose the SANbox Switch Software button On the SANbox Switch Software page scroll to the SANbox2 2Gb Series area In the Linux column choose the SANbox Manager link to open the Save As window Enter a path name to save the sansurfer_linux_install bin file and choose the Save button Open a terminal window for the directory in which the sansurfer_linux_install bin file was saved and enter the following command and press the Enter key chmod x sansurfer_linux_install bin Enter the following command sansurfer_linux_install bin Press the Enter key and follow the SANbox Manager installation instructions 59021 05 B 4 Installation Installing a Switch SE 4 2 8 SANsurfer Management Suite Disk Solaris Installation To install the SANbox Manager application on Solaris from the SANsurfer Management Suite CD ROM do the following 1 Close all programs currently running and insert the SANsurfer Management Suite Disk into the management workstation CD ROM drive Ifthe SANsurfer Management Suite start page does not open in your default browser do the following a Right click the to open the Workshops Menu
133. res a Zoning Edit session copy zone_set_source zone_set_destination Creates a new zone set named zone_set_destination and copies into it the membership from the zone set given by zone_set_source This keyword requires a Zoning Edit session create zone_set Creates the zone set with the name given by zone_set A zone set name must begin with a letter and be no longer than 64 characters Valid characters are 0 9 A Z a z _ and This keyword requires a Zoning Edit session The zoning database supports a maximum of 256 zone sets deactivate Deactivates the active zone set Close the Zoning Edit session before using this keyword 59021 05 B Simplify Zoneset Command d tt B Command Line Interface ee A delete zone_set Deletes the zone set given by zone_set Ifthe specified zone set is active the command is suspended until the zone set is deactivated This keyword requires a Zoning Edit session list Displays a list of all zone sets This keyword is available with User authority and does not require a Zoning Edit session remove zone_set zone_list Removes a list of zones given by zone _list from the zone set given by zone_set Zone names are delimited by spaces in zone _list If zone_set is the active zone set the zone will not be removed until the zone set has been deactivated This keyword requires a Zoning Edit session rename zone_set_old zone_set_new Renames the zone set given by
134. rity level given by level to use in monitoring events for the specified components or ports level can be one of the following values Critical Monitors critical events Warn Monitors warning events Info Monitors informational events To maintain optimal switch performance do not use this setting with the Component keyword set to All None Monitors none of the severity levels port port_list Specifies one or more ports to monitor for events Choose one of the following values port_list Specifies port or ports to monitor Use spaces to delimit values in the list Ports are numbered beginning with 0 All Specifies all ports None Disables monitoring on all ports restore Returns the port component and level settings to the default values save Saves the log settings for the component level and port These settings remain in effect after a switch reset The log settings can be viewed using the Show Log Settings command To export log entries to a file use the Set Log Archive command 59021 05 B B 35 B Command Line Interface d tt Set Log Command Simplify eee ee start Starts the logging of events based on the Port Component and Level keywords assigned to the current configuration The logging continues until you enter the Set Log Stop command stop Stops logging of events Notes To maintain optimal switch performance do not set the Component keyword to All and the Level keyword to
135. rvice It is intended for users who are responsible for installing and servicing network equipment 59021 05 B 1 1 1 Introduction Related Materials ee 1 2 Related Materials The following manuals and materials are referenced in the text and or provide additional information SANbox2 8c 16 Switch Management User s Guide Publication Number 59022 05 Fibre Channel Arbitrated Loop FC AL 2 Rev 6 8 Fibre Channel Private Loop SCSI Direct Attach FC PLDA NCITS TR 19 1998 Fibre Channel 10 bit Interface Rev 2 3 Definitions of Managed Objects for the Fabric Element in Fibre Channel Standard draft ietf ipfc fabric element mib 04 txt The Fibre Channel Standards are available from Global Engineering Documents 15 Inverness Way East Englewood CO 80112 5776 Phone 800 854 7179 or 303 397 7956 Fax 303 397 2740 59021 05 B gi 1 Introduction g Simplify Safety Notices SE 1 3 Safety Notices Warning notice indicates the presence of a hazard that has the potential of causing personal injury 4 3 4 5 6 1 A Caution notice indicates the presence of a hazard that has the potential of causing damage to the equipment 4 3 6 4 1 4 Sicherheitshinweise Ein Warnhinweis weist auf das Vorhandensein einer Gefahr hin die m glicherweise Verletzungen zur Folge hat 4 3 4 6 6 1 Ein Vorsichtshinweis weist auf das Vorhandensein einer Gefahr hin die m glicherweise Ger tesch den zur Folge
136. s air flow A 4 diagnostics 5 9 LEDs 2 3 marking A 4 shock A 4 status B 43 vibration A 4 classes of service A 1 Command Line Interface B 1 command syntax B 2 commands B 3 Config command B 7 configuration activate B 7 backup B 7 copy B 7 delete B 7 edit B 7 file 5 3 list B 7 remove 5 14 reset B 19 restore B 8 restore default 5 14 save B 8 configuration file system error 2 2 5 2 controls 2 2 credits 3 6 A 2 Index 1 SANbox2 16 Fibre Channel Switch Installation Guide ee D Date command B 9 device cabling 4 16 description 3 1 diagnostics 5 1 5 9 A 2 dimensions A 3 distance 3 6 domain ID 3 2 5 6 domain ID lock 3 2 domains B 44 donor port 3 6 B 44 E E_Port 2 7 5 6 emissions standards A 4 environmental conditions 4 2 specifications A 4 Ethernet connection 4 9 direct connection 4 8 indirect connection 4 8 port 2 8 event logging by component B 34 B 56 by port B 35 B 56 by severity level B 56 display B 56 restore defaults B 35 save settings B 35 settings B 56 severity level B 35 start B 36 stop B 36 external test B 63 F_Port 2 7 fabric aggregate bandwidth A 2 latency A 2 management 3 10 A 3 Index 2 management switch 2 8 management workstation 4 1 point to point bandwidth A 2 ports 2 7 security 3 11 4 10 factory defaults 5 14 B 19 Fallback command B 10 Fan Fail LED 2 3 5 10 fans 2 10 6 4 fatal error 5 1 5 2 fiber optic cable 3 1 Fibre Channel ports 2
137. s the transmission speed prior to login when the connected device powers up Related performance characteristics include the following u Distance u Bandwidth H Latency Consider the physical distribution of devices and switches in the fabric Choose SFP transceivers that are compatible with the cable type distance Fibre Channel revision level and the device host bus adapter Refer to Appendix A Specifications for more information about cable types and SFP transceivers Each port is supported by a data buffer with a 12 credit capacity that is 12 maximum sized frames For fibre optic cables this enables full bandwidth over a distance of 20 kilometers at 1 Gbps 0 6 credits Km or 10 kilometers at 2 Gbps Gbps 1 2 credits Km Beyond this distance however there is some loss of efficiency because the transmitting port must wait for an acknowledgement before sending the next frame Longer distances can be spanned at full bandwidth by extending credits on G_Ports and F_Ports Each port can donate up to 11 credits to a pool from which a recipient port can borrow For example you can configure a recipient port to borrow up to 66 credits from 6 ports for a total of 78 credits This will support communication over approximately 130 Km at 1 Gbps 78 0 6 or 65 Km at 2 Gbps 78 1 2 You can configure recipient and donor ports using SANbox Manager or the Set Config command Refer to Set Config Command on page B 26 for more information
138. se the ports are self configuring you can connect SANbox2 16 and other FC SW 2 compliant switches together in a wide variety of topologies 3 2 1 Domain ID Principal Priority and Domain ID Lock The following switch configuration settings affect multiple chassis fabrics m Domain ID u Principal priority Domain ID lock The domain ID is a unique number from 1 239 that identifies each switch in a fabric The principal priority is a number 1 255 that determines the principal switch which manages domain ID assignments for the fabric The switch with the highest principal priority 1 is high 255 is low becomes the principal switch If the principal priority is the same for all switches in a fabric the switch with the lowest WWN becomes the principal switch The domain ID lock allows FALSE or prevents TRUE the reassignment of the domain ID on that switch Switches come from the factory with the domain ID set to 1 the domain ID lock set to FALSE and the principal priority set to 254 Refer to the SANbox2 8c 16 Switch Management User s Guide for information about changing the domain ID using SANbox Manager Refer to Set Config Command on page B 26 for information about changing the default domain ID domain ID lock and principal priority parameters An unresolved domain ID conflict means that the switch with the higher WWN will isolate as a separate fabric and the Logged In LEDs on both switches will flash to show the affected ports
139. set Type help with one of the following to get more information set alarm set beacon set blade set config blade set config port set config ports set config switch set config threshold set config zoning set log set pagebreak set port set setup snmp set setup system set switch The following is an example of the Help Set Beacon command SANbox2 gt help set beacon set beacon On Off This command allows the LEDs on the front of the switch to flash The On option will start and the Off option will stop the flashing 59021 05 B B 11 B Command Line History Command nterface d tt implify ee History Command Displays a numbered list of the previously entered commands from which you can re execute selected commands Authority User Syntax history Notes Use the History command to provide context for the command a Enter command to re enter the most recent execution of that command Enter line number to re execute the corresponding command from the History display M Enter partial command string to re execute a command that matches the command string E Enter to re execute the most recent command Examples The following is an example of the History command SANbox2 gt history 1 2 3 4 show switch date help set history SANbox2 gt 3 help set set SET_OPTIONS There are many attributes that can be set Type help with one of the following
140. since the last Zoning Save command was entered save Saves changes made during the current Zoning Edit session The system will inform you that the zone set must be activated to implement any changes This does not apply if you entered the Zoning Clear command during the Zoning Edit session Examples The following is an example of the Zoning Edit command SANbox2 gt admin start SANbox2 admin gt zoning edit SANbox2 admin zoning gt SANbox2 admin zoning gt zoning cancel Zoning edit mode will be canceled Please confirm y n n y SANbox2 admin gt admin end The following is an example of the Zoning List command SANbox2 gt zoning list Active ZoneSet Information wwn_b0241f 50 06 04 82 bf d2 18 c2 50 06 04 82 bf d2 18 d2 21 00 00 e0 8b 02 41 2f wwn_23bd31 B 78 59021 05 B d tt B Command Line Interface Simplify A D Zoning Command EE 50 06 04 82 bf d2 18 c2 50 06 04 82 bf d2 18 d2 19 00 00 00 69 23 bd1 31l wwn_221416 50 06 04 82 bf d2 18 c2 50 06 04 82 bf d2 18 d2 10 00 00 00 c9 22 14 16 wwn_2215c3 50 06 04 82 bf d2 18 c2 50 06 04 82 bf d2 18 d2 10 00 00700 09 22 15 03 Configured Zoning Information wwn_b0241f 50 06 04 82 bf d2 18 c2 50 06 04 82 bf d2 18 d2 21 00 00 e0 8b 02 41 2f wwn_23bd31 50 06 04 82 bf d2 18 c2 50 06 04 82 bf d2 18 d2 10 00 00 00 c9 23 bd 31 wwn_221416 50 06 04 82 bf d2 18 c2 50 06 04 82 bf d2 18 d2 10 00 00 00 c9 22 14 16 wwn_2215c3
141. supply 2 9 6 3 switch 2 2 power on self test description 5 1 log B 47 results 4 7 principal priority 3 2 Index 4 switch 3 2 Ps command B 17 Q Quit command B 18 R rack mount 4 3 recovering a switch 5 12 regulatory certifications A 4 remake filesystem 5 14 removal replacement 6 1 Reset command B 19 RS 232 port 2 8 rubber feet 4 2 S safety standards A 4 SANbox Manager 2 11 SANbox Manager installation Linux 4 12 4 14 Solaris 4 13 4 14 Windows 4 11 4 14 scalability A 1 security 3 11 4 10 serial port 2 8 4 8 4 9 Set command B 24 Set Config command B 26 Set Log command B 34 Set Port command B 37 Set Setup command B 38 SFP See Small Form Factor Pluggable Show command B 43 Show Config command B 53 Show Log command B 56 Show Perf command B 58 Show Setup command B 60 Shutdown command B 62 Simple Network Management Protocol 2 11 configuration B 38 configuration display B 60 reset B 19 site requirements 4 1 59021 05 B SANbox2 16 Fibre Channel Switch Installation Guide SE small form factor pluggable 2 5 4 4 6 2 SNMP See Simple Network Management Protocol soft zone 3 9 steering B 47 switch administrative state B 25 configuration 4 15 B 28 configuration display B 53 initialize B 19 management 2 11 manufacturer information B 60 operational information B 48 power down 4 20 recovery 5 12 reset 2 2 5 14 B 66 specifications A 1 system processor A 2 system configura
142. switch s permanent memory Changes are always saved in the switch s temporary memory Default Enables All or disables None communication among the switch s ports devices and the fabric in the absence of an active zone set Examples The following is an example of the Set Config Port command SANbox2 gt admin start SANbox2 admin gt config edit SANbox2 admin config gt set config port 1 A list of attributes with formatting and current values will follow Enter a new value or simply press the ENTER key to accept the current value If you wish to terminate this process before reaching the end of the list H press q or Q and the ENTER key to do so Configuring Port Number 1 AdminState 1 Online 2 0ffline 3 Diagnostics 4 Down Online LinkSpeed 1 1Gb s 2 2Gb s 3 Auto Auto PortType TL GL G F FL Donor GL ISLSecurity Any Ours None Any SymPortName string max 32 chars Porti ALFairness True False False DeviceScanEnable True False True ForceOfflineRSCN True False False ARB_FF True False False InteropCredit decimal value 0 255 0 ExtCredit dec value increments of 11 non loop only 0 B 30 59021 05 B Simplify Set Config Command d tt B Command Line Interface ZZZ FANEnable True False True LCFEnable True False False MFSEnable True False False MFS_TOV decimal value 10 20480 msec 640 MSEnable True False Tr
143. t gt q gt mmo mm 5 1 1 4 Fatal Error Blink Pattern A fatal error blink pattern is 3 blinks per second followed by a two second pause The 3 blink error pattern indicates that a fatal error has left the switch inoperable If a fatal error occurs contact your authorized maintenance provider 1 second 2 seconds sm 5 1 1 5 Configuration File System Error Blink Pattern A configuration file system error blink pattern is 4 blinks per second followed by a two second pause The 4 blink error pattern indicates that a configuration file system error has occurred and that the configuration file must be recreated Refer to Recovering a Switch on page 5 12 for more information 1 second 2 seconds gt pn mr To recreate the configuration file do the following 1 Open a Telnet session and use the Shutdown command to close activity on the switch then power down the switch Refer to the Shutdown Command on page B 62 5 2 59021 05 B Simplify POST Diagnostics SE 2 Place the switch in maintenance mode Press and hold the Maintenance button then power up the switch Refer to Recovering a Switch on page 5 12 for more information about placing the switch in maintenance mode d tt 5 Diagnostics Troubleshooting 3 Establish a Telnet session with the switch using the default IP address 10 0 0 1 telnet 10 0 0 1 4 Enter the account name prom and password prom and pr
144. t is a port can be a member of more than one ACL zone m ACL zones that include members from multiple switches need not include the ports of the inter switch links m ACL zone boundaries supersede soft zone boundaries but yield to VPF zone boundaries Mm Membership can be defined only by domain ID and port ID H ACL zoning supports all port modes except TL_ Port 59021 05 B 3 9 3 Planning df Fabric Management BE OO o 3 4 3 Virtual Private Fabric Hard Zones Virtual Private Fabric VPF zoning divides the fabric for purposes of controlling discovery and both inbound and outbound traffic This type of zoning is useful for providing security and reserving paths between devices to guarantee bandwidth VPF zoning is a type of hard zoning that is hardware enforced Members can only transmit to and receive from members of the same VPF zone The VPF zone boundary is secure against both inbound and outbound traffic The following rules apply to VPF zones m VPF zones that include members from multiple switches must include the ports of the inter switch links VPF zones cannot overlap that is a port can be a member of only one VPF zone m VPF zone boundaries supersede both soft and ACL zone boundaries Mm Membership can be defined only by domain ID and port ID m VPF zoning supports all port modes 3 5 Fabric Management The SANbox Manager application and CLI execute on a management workstation that provi
145. tch operational information topology Displays all connected devices users Displays a list of logged in users This is equivalent to the User List command version Displays an introductory set of information about operational attributes of the switch This keyword is equivalent to the About keyword Examples The following is an example of the Show Chassis command SANbox2 gt show chassis Chassis Information BoardTemp 1 Degrees Celsius 32 BoardTemp 2 Degrees Celsius 36 FanStatus 1 Good FanStatus 2 Good PowerSupplyStatus 1 Good PowerSupplyStatus 2 Good The following is an example of the Show Domains command SANbox2 gt show domains Principal switch is local 10 00 00 c0 dd 00 90 6b Domain ID List Domain 22 0x16 WWN 10 00 00 c0 dd 00 90 6b The following is an example of the Show Fabric command SANbox2 gt show fabric Switch ID WWN Eth0IPAddress 1 0x1 fffc01 10 00 00 c0 dd 00 bd ec 10 20 68 107 4 0x4 fffc04 10 00 00 c0 dd 00 80 21 10 20 68 14 B 48 59021 05 B Simplify Show Command d tt B Command Line Interface nn A The following is an example of the Show NS local domain command SANbox2 gt show ns Seq Domain Port Port No ID ID Type COS PortWWN NodeWWN 1 99 0x63 630425 NL 3 21 00 00 20 37 d9 4b 2a 20 00 00 20 37 d9 4b 2a 2 99 0x63 6304e8 NL 3 21 00 00 20 37 d9 4b 2f 20 00 00 20 37 d9 4b 2f 3 99 0x63 6304ef NL 3 21 00 00 20 37 d9 4f 46 20 00 00 20
146. ter than that of the mesh topology Mm Latency between any two device ports is three chassis hops a 52 Fibre Channel ports are available for devices Core Switch Coe ee ets ane nl CH Un enn de Edge Switch Edge Switch 6 SR Os EE 828 Edge Switch f eo Teen o Je a N Co Figure 3 3 Multistage Topology 59021 05 B 3 5 3 Planning Performance ee 3 3 Performance 3 3 1 Distance 3 6 The SANbox2 16 switch supports class 2 and class 3 Fibre Channel service at transmission rates of 1 Gbps or 2 Gbps with a maximum frame size of 2148 bytes A port can transmit or receive at 1 Gbps or 2 Gbps depending on the device to which it is connected The port discover
147. the log becomes full the entries are replaced starting with the oldest entry to produce a list of the last 200 events which occurred Log entries are created for ports components and event severity levels Admin set log archive clear component list level level port port_list restore save start default stop archive Archives the log entries to a file on the switch named ogfile that can be downloaded from the switch using FTP To download the log file open an FTP session log in with account name password of images for both and type get logfile clear Clears all log entries component list Specifies one or more components to monitor for events Use spaces to delimit values in the list Choose one or more of the following values All Monitors all components To maintain optimal switch performance do not use this setting with the Level keyword set to Info Chassis Monitors chassis hardware components such as fans and power supplies Eport Monitors all E Ports Mgmtserver Monitors management server status Nameserver Monitors name server status None Monitor none of the component events 59021 05 B Simplify Simplify Set Log Command d tt B Command Line Interface ls Other Monitors other miscellaneous events Port Monitors all port events Switch Monitors switch management events Zoning Monitors zoning conflict events level level Specifies the seve
148. the format XX XX XX XX XX XX XXIXX G Alias name rename zone_old zone_new Renames the zone given by zone_old to the zone given by zone_new type zone zone_type Specifies the zone type given by zone_type to be assigned to the zone name given by zone If you omit the zone_type the system displays the zone type for the zone given by zone zone_type can be one of the following soft Name server zone hardACL Access control list hard zone This keyword is case sensitive hardVPF Virtual private fabric hard zone This keyword is case sensitive zonesets zone Displays all zone sets of which the zone given by zone is a member This keyword is available with User authority and does not require a Zoning Edit session 59021 05 B B 71 B Command Line Interface d tt Zone Command Simplify ee Examples The following is an example of the Zone List command SANbox2 gt zone list wwn_b0241f zone_set_1 wwn_23bd31 zone_set_1 wwn_221416 zone_set_1 wwn_2215c3 zone_set_1 wwn_0160ed zone_set_1 wwn_c001b0 zone_set_1 wwn_401248 zone_set_1 wwn_02402 zone_set_1 wwn_22412f zone_set_1 The following is an example of the Zone Members command SANbox2 gt zone members wwn_b0241f Current List of Members for Zone wwn_b0241f 50 06 04 82 bf d2 18 c2 50 06 04 82 bf d2 18 d2 21 00 00 e0 8b 02 41 2f B 72 59021 05 B Simplify Zone Command d B Command Line Interfac
149. the switch given by domain_id domain_id is a switch domain ID port_id Displays name server information for the port given by port_id port_id is a port Fibre Channel address pagebreak Displays the current pagebreak setting The pagebreak setting limits the display of information to 20 lines On or allows the continuous display of information without a break Off B 44 59021 05 B B Command Line Interface ic of Show Command TTT _ a perf option Displays performance information for all ports Refer to the Show Perf Command on page B 58 port port_number Displays operational information for the port given by port_number Ports are numbered beginning with 0 If the port number is omitted information is displayed for all ports Table B 13 describes the port parameters Table B 13 Show Port Parameters 59021 05 B Entry Description Alinit Incremented each time the port begins AL initialization AlinitError Number of times the port entered initialization and the ClassXFramesin ClassXFramesOut ClassXWordsin initialization failed Number of class x frames received by this port Number of class x frames sent by this port Number of class x words received by this port ClassXWordsOut Number of class x words sent by this port DecodeError Decoding error detected FBusy Number of times the switch sent a F_BSY because Class 2 frame could not be delivered within ED_TOV tim
150. tion change B 39 display B 60 table mount 4 3 target device 2 7 temperature 4 2 A 4 B 43 Test command B 63 time B 9 timeout value 5 6 TL_Port devices 2 7 name server registration 2 7 number of off loop devices 2 7 private targets 2 7 topology cascade 3 3 mesh 3 4 Multistage 3 5 transceiver 2 5 4 4 6 2 translation entries list 2 7 transmission rate 3 6 3 7 59021 05 B U Uptime command B 66 user account 3 11 B 1 authority 3 11 B 3 interface A 2 logged in B 48 User command B 67 ventilation 2 10 vibration A 4 Virtual Private Fabric zone 3 10 voltage fluctuations A 4 operating A 3 W Whoami command B 69 workstation 4 1 4 8 worldwide name 3 8 WWN See Worldwide Name Z zone access control list 3 9 add member port B 70 conflict 5 6 copy B 70 create B 70 definition 3 8 delete B 70 delete member port B 71 list B 71 list members B 71 name server 3 9 rename B 71 type B 71 virtual private fabric 3 10 Zone command B 70 zone set 3 8 activate B 74 active B 77 Index 5 d tt SANbox2 16 Fibre Channel Switch Simplify Installation Guide E QQ add member zone B 74 copy B 74 create B 74 deactivate B 19 B 74 delete B 75 delete member zone B 75 display B 75 display active B 74 display members B 75 display zones B 71 rename B 75 Zoneset command B 74 zoning configuration B 30 configuration display B 53 database 3 8 B 19 edit B 77 history B 77 limits 3 8 B 78 list d
151. to get more information set alarm set beacon set blade set config blade set config port set config ports set config switch set config threshold set config zoning set log set pagebreak set port set setup snmp set setup system set switch B 12 59021 05 B B Command Line Interface Image Command SE Image Command Authority Syntax Keywords Notes 59021 05 B Manages and installs switch firmware Admin image cleanup fetch account name Im address file source file destination list unpack file cleanup Removes all firmware image files from the switch All firmware image files are removed automatically each time the switch is reset fetch account name ip_address file_source file_destination Retrieves image file given by file_source and stores it on the switch with the file name given by file_destination The image file is retrieved from the device with the IP address given by ip_address and an account name given by account_name If an account name needs a password to access the device the system will prompt you for it list Displays the list of image files that reside on the switch unpack file Installs the firmware file given by file After unpacking the file a message appears confirming successful unpacking The switch must be reset for the new firmware to take effect To provide consistent performance throughout the fabric ensure that all switches are run
152. ts self configure in the following ways n FL_Port when connected to a loop of public devices a F_Port when connected to a single public device If the device is a single device on a loop the GL_Port will attempt to configure first as an F_Port then if that fails as an FL_Port u E_Port when connected to another FC SW 2 compliant switch 2 6 59021 05 B gi 2 General Description q Simplify Fibre Channel Ports ls G_Ports self configure in the following ways m EF Port when connected to a public device a E Port when connected to another FC SW 2 compliant switch A TL_Port supports private loop devices and must be configured explicitly Refer to the SANbox2 8c 16 Switch Management User s Guide for more information about defining port modes 2 2 3 1 Fabric Ports An FL_Port can support a loop of up to 126 public devices An FL_Port can also configure itself during the fabric login process as an F_Port when connected to a single public device N_ Port 2 2 3 2 Translated Loop Port A TL_Port supports a loop of up 124 private target devices with the ability to communicate with up to 63 off loop public devices Private loop initiator devices are not supported on the TL_Port The TL_Port acts as a proxy for the off loop device translating private frames into and from public frames The set of off loop devices are maintained in the TL_Port s translation entries list The switch firmware automatically creates an entry in t
153. tup Command d tt B Command Line Interface A 5 56 TraplSeverity see allowed options above warning TraplVersion 1 2 2 TraplEnabled True False False Trap2Address dot notated IP Address 0 0 0 0 Trap2Port decimal value 162 Trap2Severity see allowed options above warning Trap2Version ERC 2 2 Trap2Enabled True False False Trap3Address dot notated IP Address 0 0 0 0 Trap3Port decimal value 162 Trap3Severity see allowed options above warning Trap3Version 1 2 2 Trap3Enabled True False False Trap4Address dot notated IP Address 0 0 0 0 Trap4Port decimal value 162 Trap4Severity see allowed options above warning Trap4Version 1 2 2 Trap4Enabled True False False Trap5Address dot notated IP Address 0 0 0 0 Trap5Port decimal value 162 Trap5Severity see allowed options above warning Trap5Version 1 2 2 Trap5Enabled True False False ReadCommunity string max 32 chars public WriteCommunity string max 32 chars private TrapCommunity string max 32 chars public AuthFailureTrap True False False ProxyEnabled True False True 59021 05 B B 41 Set Setup Command Simplify B Command Line Interface d tt Ca ooo B ooo The following is an example of the Set Setup System command SANbox2 admin gt set setup system A list of attributes with formatting and current values will follow Enter a new value or simply press the ENTER key to accept the current value If
154. ue NoClose True False False IOStreamGuard Enable Disable Disable VIEnable True False False CheckAlps True False False Finished configuring attributes This configuration must be saved see config save command and activated see config activate command before it can take effect To discard this configuration use the config cancel command The following is an example of the Set Config Switch command SANbox2 gt admin start SANbox2 admin gt config edit SANbox2 admin config gt set config switch A list of attributes with formatting and default values will follow Enter a new value or simply press the ENTER key to accept the current value If you wish to terminate this process before reaching the end of the list press q or Q and the ENTER key to do so AdminState 1 Online 2 0ffline 3 Diagnostics Online BroadcastEnable True False False InbandEnabled True False False DefaultDomainID decimal value 1 239 11 DomainIDLock True False True SymbolicName string max 32 chars SANbox2 switch R_T_TOV decimal value 1 1000 msec 100 R_A_TOV decimal value 100 100000 msec 10000 E_D_TOV decimal value 10 20000 msec 2000 FS_TOV decimal value 100 100000 msec 5000 DS_TOV decimal value 100 100000 msec 5000 PrincipalPriority decimal value 1 255 254 ConfigDescription string max 32 chars The following is an example of the Set Config Threshold command SANbox2 gt adm
155. very switch le Yes Continue m No Correct the timeout values on the offending switches using the Set Config Switch command or the SANbox Manager Switch Properties window Reset the port If the condition remains continue Display the active zone set on each switch using the Zoning Active command or the Active Zoneset tab of the SANbox Manager topology display Compare the zone membership between the two active zone sets Are they the same m Yes Contact your authorized maintenance provider m No Deactivate one of the active zone sets or edit the conflicting zones so that their membership is the same Reset the port Ifthe condition remains contact your authorized maintenance provider Note This can be caused by merging two fabrics whose active zone sets have two zones with the same name but different membership 59021 05 B gi 5 Diagnostics Troubleshooting q Simplify POST Diagnostics nn y Ei 5 1 2 2 Excessive Port Errors The switch monitors a set of port errors and generates alarms based on user defined sample intervals and thresholds Refer to the SANbox2 8c 16 Switch Management User s Guide for information about managing alarms These port errors include the following CRC errors Decode errors ISL connection count Login errors Logout errors H Loss of signalerrors If the count for any of these errors exceeds the rising threshold for three consecutive sample intervals the switch generates an alar
156. wayAddress IP address gateway AdminTimeout Specifies the amount of time in minutes the switch waits before terminating an idle Admin session Zero 0 disables the time out threshold The default is 30 the maximum is 1440 TempMonitoringWarning Warning temperature threshold in C above which a warning condition alarm is generated The default is 65 C TempMonitoringFailure Failure temperature threshold in C above which a failure condition alarm is generated The default is 70 C TempFailurePortShutdown Enables True or disables False the switch s ability to place all ports offline when the internal temperature exceeds the failure threshold The default is False 59021 05 B B 39 B Command Line Interface d tt Set Setup Command Simplify U ooo 7 Table B 12 System Configuration Settings Continued Entry Description SecurityEnabled Enables True or disables False the enforcement of account names and passwords The default is False LocalLogEnabled Enables True or disables False the saving of log information on the switch The default is True RemoteLogEnabled Enables True or disables False the recording of the switch event log on a remote host that supports the syslog protocol The default is False RemoteLogHostAddress The IP address of the host that will receive the switch event log information if remote logging is enabled The default is 10 0 0 254 Notes
157. word X X 4 2 5 Install SANbox Manager You can install SANbox Manager on the Windows Linux and Solaris platforms Your switch was shipped with either a SANsurfer Management Suite Disk or a SANbox2 Installation Disk Refer to the following installation instructions that correspond to your situation SANsurfer Management Suite Disk Windows Installation SANsurfer Management Suite Disk Linux Installation SANsurfer Management Suite Disk Solaris Installation SANbox2 Installation Disk Windows Installation SANbox2 Installation Disk Linux Installation SANbox2 Installation Disk Solaris Installation 4 10 59021 05 B 4 Installation Installing a Switch ZZZ A 4 2 6 SANsurfer Management Suite Disk Windows Installation To install the SANbox Manager application on Windows from the SANsurfer Management Suite Disk do the following 1 59021 05 B Close all programs currently running and Insert the SANsurfer Management Suite Disk into the management workstation CD ROM drive Ifthe SANsurfer Management Suite start page does not open in your default browser do the following a Using Windows Explorer double click the drive letter which contains the SANsurfer Management Suite Disk b Locate and double click the Start_Here htm file to open the SANsurfer Management Suite start page in your default browser On the SANsurfer Management Suite start page choose the SANbox Switch Software button On the
158. zone_set_old to the name given by zone_set_new You can rename the active zone set This keyword requires a Zoning Edit session zones zone_set Displays all zones that are members of the zone set given by zone_set This keyword is available with User authority and does not need a Zoning Edit session Notes Mm Azone set must be active for its definitions to be applied to the fabric E Only one zone set can be active at one time m Azone can be a member of more than one zone set Examples The following is an example of the Zoneset Active command SANbox2 gt zoneset active Active ZoneSet Information ActiveZoneSet Beta LastActivatedBy Remote LastActivatedOn Mon Apr 21 09 20 56 2003 The following is an example of the Zoneset List command SANbox2 gt zoneset list Current List of ZoneSets alpha beta 59021 05 B B 75 B Command Line Interface d tt Simplify Zoneset Command implify U ooo o o 2 The following is an example of the Zoneset Zones command SANbox2 gt zoneset zones ssss Current List of Zones for ZoneSet ssss zonel zone2 zone3 B 76 59021 05 B B Command Line Interface Zoning Command SE Zoning Command Authority Syntax Keywords 59021 05 B Opens a Zoning Edit session in which to create and manage zone sets and zones Refer to the Zone Command on page B 70 and the Zoneset Command on page B 74 Admin The List keyword is available with User authority

Download Pdf Manuals

Related Search

Related Contents

1 - Support Sagemcom  Massive Wall light 17183/93/10    CB-101  N400788 man compact radio DCR006 Euro    MANUAL DE USUARIO  EGG ROLLER  IRET \  Amministrare GNU/Linux  

Copyright © All rights reserved. Failed to retrieve file