Pyramid Car Audio CDR40DX User's Manual
Contents
1. MAIN UNIT ANTENNA CONNECTOR IGNITION RED SWITCH B MEMORY YELLOW BACK UP GREY en BLACK RCA CABLE c GROUND Lch WHITE POWER BLUE FOR RCA LINE OUT VERSION ONLY ANTENNA con POWER ANT VERSION ONLY WHITE GREY LEFT 41 RIGHT SPEAKER 1 WHITE BLACK GREY BLACK EN SPEAKER OPERATION 7 OC 11 13 1 42 18 COMPACT DISC PLAYER EJECT REL B 5 Loc Ow TUNI RER PWR gt Ost e 5900900 LecccceoR 290900 VOL BAL TONE euP 6 4 5 0 3 2 4 20 17 Olo RESET 9 O E C O CJ 0 GENERAL OPERATION ON OFF Press PWR button 1 to turn on the unit Press it again to turn it off BALANCE Slide BAL button 2 to left or right to adjust sound balance between left and right speakers VOLUME Slide VOL button 3 to left or right to adjust volume level TONE CONTROL Slide TONE button 4 to left or right to obtain the desired sound quality SELECT MODE Press MODE button 5 to change radio mode or CD mode OPERATION RESET BUTTON RESET button 17 is placed on the housing and must be activated with either a ballpoint pen or thin metal object The RESET button 17 is to be activated for the follow2. TROUBLE SHOOTING Before going through the check list check wiring connection If any of the problems persist after check list has been made consult your nearest service dealer The operation keys do not work more than 30 degrees The disc is extremely dirty or defective disc The built in microcomputer is not operating properly due to noise Symptom Cause Solution No power The car ignition switch is If the power supply is properly not on connected to the car accessory circuits but the engine is not moving switch the ignition key to ACC The fuse is blown Replace the fuse Disc cannot Presence of CD disc inside Remove the disc in the player then be loaded or the player put a new one ejected Inserting the disc in Insert the compact disc with the reverse direction label facing upward Compact disc is extremely Clean the disc or try to play a new dirty or defective disc one Temperature inside the car Cool off or until the ambient is too high temperature return to normal Condensation Leave the player off for an hour or so then try again No sound Volume is in minimum Adjust volume to a desired level Wiring is not properly Check wiring connection connected Sound skips The installation angle is Adjust the installation angle to less than 30 degrees Clean the compact disc then try to play a new one Press the RESET button Front panel is not properl
3. or the previous FAST FORWARD AND FAST REVERSE Hold button 15 or the button 14 for several seconds to fast forward or fast reverse Releasing the button to stop fast playing REPEAT REPEAT THE SAME TRACK During CD operation press REP LOC button 9 to continuously repeat playing the current track Press it again to release the mode INTRO PREVIEW ALL TRACKS During CD operation press INTRO button 10 to play first several seconds of each track Press it again to stop intro and listen to track RANDOM PLAY ALL TRACKS IN THE RANDOM ORDER During CD operation press and hold RND button 6 for several seconds to play all tracks in the random order Press it again to cancel the function LIQUID CRYSTAL DISPLAY During CD mode the LCD 16 can show the current CD working status of the unit SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls Bass at 100 Hz Treble at 10 KHz Maximum Output Power Current Drain CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response RADIO Frequency Coverage Sensitivity S N 30 dB Stereo Separation Frequency Coverage Sensitivity S N 20 dB DC 12 Volts Negative Ground 178 W x 163 D x 50 H mm 10 dB 10 dB 7W x 2 ch 3 Ampere More than 60 dB More than 60 dB 20 Hz 20 KHz FM 88 to 108 MHz 10 7 MHz Suv gt 30 dB AM 530 to 1710 KHz 450 KHz 32 dBu
4. PYRANMWS CDR40DX OWNER S MANUAL MANUALLY TUNED STEREO RADIO WITH COMPACT DISC PLAYER www pyramidcaraudio com CONTENTS Installation aa 3 DIN Front Mount Method A 3 Installing theunit i dede de 3 Removing the eel ie 4 DIN Rear Mount Method 4 How Remove And Install The Front 5 Wiring Connection siksa asasaran angkane aana 6 Operation ei 7 General Operation lt saras A aaa aaa eaten aa aa aa a aane Tan 7 Radio Operation a sisa ih oer een pa aaa ga anga nae 8 GD Operation s io ec A a SE tse Ret 9 1 10 Trouble Shooting 11 INSTALLATION Notes Choose the mounting location where the unit will not interfere with the normal driving function of the driver Before finally installing the unit connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the veh
5. aching the frame point the side with a groove downwards and attach it Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click Pulling the levers makes it possible to remove the unit from the dashboard DIN REAR MOUNT Method B Installation using the screw holes on the sides of the unit Fastening the unit to the factory radio mounting bracket 1 aR 0 n Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned are fitted and tighten the screws at 2 places on each side Use either truss screws 5 x 5mm or flush surface screws 4 x 5mm depending on the shape of the screw holes in the bracket Screw Factory radio mounting bracket Dashboard or Console Hook Remove this part Note The mounting box outer trim ring and half sleeve are not used for method B installation INSTALLATION HOW TO REMOVE AND INSTALL THE FRONT PANEL 1 Press the release button and pull off the front panel Keep the front panel into the case To install the front panel insert the panel into the housing and make sure the panel is properly installed otherwise abnormalities occurs on the display or some keys will not function properly REMOVING THE FRONT PANEL Front Panel Release Button INSTALLING THE FRONT PANEL WIRING CONNECTION
6. icle e Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop like an emergency stop f installation angle exceeds 30 from horizontal the unit might not give its optimum performance p 30 Avoid installing the unit where it would be subject to high temperature such as from direct sunlight or from hot air from the heater or where it would be subject to dust dirt or excessive vibration DIN FRONT REAR MOUNT This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of the unit chassis For details refer to the following illustrated installation methods DIN FRONT MOUNT Method A Installing the unit 1 Dashboard 2 Holder After inserting the holder into the dashboard select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place 3 Screw Fig 1 INSTALLATION Oo wm Dashboard Nut 6mm Spring washer Screw 5 x 25mm Screw Strap Be sure to use the strap to secure the back of the unit in place The strap can be bent by hand to the desired angle Plain washer Removing the unit 1 2 Frame Insert fingers into the groove in the front of frame and pull out to remove the frame When reatt
7. ing reasons e Initial installation of the unit when all wiring is completed e All the function buttons do not operate e Error symbol on the display FACEPLATE RELEASE Press REL button 18 to detach the removable faceplate FLASHING LED If the front panel does not install in the main unit the LED indicator 20 will be flashing RADIO OPERATION BAND SELECTOR Press BND button 7 to change bands as below FM gt SELECT STATION Rotate the TUNE knob 8 clockwise or anti clockwise to adjust the frequency upward or downward LOCAL DISTANT Press the REP LOC button 9 to select between local setting for reception of strong station and distant setting for reception of weak stations when tuning FREQUENCY DISPLAY The frequency of current reception is indicated by the dial pointer 19 OPERATION CD OPERATION DISC PLAY Gently insert a compact disc with the label side facing up into the disc slot 13 The disc is then automatically loaded into the unit and starts playing with the first track of the disc The digital display will indicate the track number and the time of the track EJECT Press eject button 12 to stop CD play and eject CD from slot Receiver switches to radio operation PAUSE CD During CD playing press Pil button 11 to temporarily stop playing Press it again to resume playback SKIP TRACKS Press button 15 or the button 14 to choose the following track
8. y fixed into its place The radio does not work The radio station automatic selection does not work The antenna cable is not connected Insert the antenna cable firmly The signals are too weak Select a station manually 88 C3191 11
Download Pdf Manuals
Related Search