PYLE Audio PSS8 User's Manual
Contents
1. PYLE PRO HIGH POWER STEREO SPEAKER SELECTOR MODEL PSS8 www pyleaudio com Thank you for purchasing PYLE PRO Multi Speaker Selectors It lets you connect up to eight separate pairs of speakers to your stereo receiver amplifier The control center is especially convenient if you have speaker sets in different rooms and want to turn them on and off independently You can enjoy the convenience and flexibility of listening to multiple speaker pairs simultaneously HIGH POWER STEREO SPEAKER CONTROL CENTER PSS8 PROTECTION Terminal Buttons Protection Buttons The control center lets you use one to eight sets of speakers at a time and is designed to operate with a stereo receiver amplifier that has a maximum of 100 watts per channel and with speaker systems that have a minimum impedance of 8 ohms see Impedance Chart on page 5 PREPARATIONS Use the PYLE PRO Speaker Selectors only with amplifiers rated at 100 watts per channel or less Your PYLE PRO Speaker Selector is designed to accept any size cable up to 14 gauge non terminated speaker wire If you re using non terminated speaker wire do not use any speaker wire that is larger than 14 gauge The lower the gauge number the larger the cable e g 12 gauge is larger in actual physical size than 14 gauge Do not hook the outputs of one selector into the inputs of another speaker selector together MAKING THE CONNECTIONS The control center divides th2. A D E A E F A F G A G H B C D B D E B E F B F G B G H C D E C E F C F G C G H C H A C H B D E F D F G D G H D H A D H B E F G E G H 3 E H A E A B E B C F G H F H A F A B F B C F D E G H A G B C G C D G D E G E F H A B H B C H C D H D E H E F H F G A B C D A C D E A D E F A E F G A F G H B C D E B D E F B E F G B F G H 2 4 A B G H A B C H C D E F C E F G C F G H A C G H D E F G D F G H A D G H A B D H E F G H A E G H A B E H A B C E A B F H A B E F B C D F A B C G C D E G B C D H C D E H D E F H A D E F G A E F G H B C D E F B D E F G B E F G H A B F G H C D E F G C E F G H A C F G H A B C G H D E F G H A D F G H A B D G H A B C D H A B E G H A B C E H A B C D E A C D E F A B C D E H A B C D E F A C D E F G A D E F G H A B E F G H A B C F G H A B C D G H 1 8 A B C D E F G A C D E F G H A B D E F G H A B C E F G H A B C D F G H A B C D E G H A B C D E F H 1 5 A B C D E F G H 1 4 SPECIFICATIONS Audio Power Handling Frequency Response Channel Separation Crosstalk between channels Speaker terminal wire size requirements Dimensions WxHxD Weight 50W R M S ch 100W Max ch 20 Hz to 20KHz 80 dB 50 dB 14 22 awg 315x50x150 mm 1 50kgs 3 30lbs
3. receiver amplifier has more than one set of speaker terminal A and B connect only one or the other to the control center e For the best results we recommend 14 gauge two conductor speaker wire not supplied for most connections If you plan to located the speakers further than 80 feet from the control center use a heavier gauge of wire OPERATION Caution To avoid damaging your receiver amplifier set its volume to the lowest setting before changing the control center s settings To turn on a pair of speakers connected to the control center simply press in the desired button For example to turn on the set of speakers connected to SPK A press A To turn off a pair of speakers press the button again so it is in the out position Note If no speakers are connected to a set of terminals do not press in the corresponding control button IMPEDANCE CHART Impedance is a measurement of the load placed on your receiver amplifier by the speakers The load placed on your receiver amplifier from thte control center will vary depending on how many pairs of speakers you turn on at one time and on which speakers you turn on The chart below shows the impedance for all possible combinations of 8 ohm speakers Speaker Sets On Impedance Q A B C D E F G H 8 A B A C A D A E A F A G A H B C B D B E B F B G B H C D C E C F C G C H 4 D E D F D G D H E F E G E H F G F H G H A B C A C D
4. e power from your receiver amplifier differently to its speaker terminals This is especially noticeable when you connect only one pair of speakers If you connect more than one pair of speakers see Impedance Chart on page 5 to selector the best terminals to connect For the best performance make the connections based on how frequently you use each set of speakers Cautions To avoid damaging your speakers or receiver amplifier e Be sure your receiver amplifier s power is turned off before you make the connections e Never let the speaker wire s bare ends touch each other or the adjacent terminals on the control center Do not connect more than one pair of sepakers to each set of terminals Press open the desired SPK terminals on the control center Insert the speakers positive wires in the positive red terminals and negative wires into the nagative black terminals according to the respective L left and R right terminals Then press the tabs to close them A Speaker Terminals AMPLIFIER AMP Terminals Press open the AMP terminals on the control center then insert your receiver amplifier s positive wires into the positive red terminals and negative wires in the nagative black terminals Then press the tabs to close them Notes If your
Download Pdf Manuals
Related Search