PYLE Audio PRO PCA1 User's Manual
Contents
1. SPYLE PRO PCA1 2X15 Watt Stereo Power Amplifier PYLEPRO PEAI Stereo Power Amplifier www pyleaudio com Your New Pyle Pro Amplifier gives you the power and versatility you need in a professional sound system The amplifier s wide frequency response makes it suitable for amplifying music or vocal program material PCA1 can compatible with walkman and computerize devices MP3 via 3 5mm to RCA converter Please read this manual thoroughly before you attempt to set up and use the amplifier It contains a range of installation suggestions as well as instructions to ensure safe usage Installed properly you can expect years of trouble free service from this product TABLE OF CONTENTS 1 Features and Controls 2 Caring for your Pyle Pro Amplifier 3 Trouble shooting 4 Limited warranty adn Specifications CAUTION WARNING To reduce the RISK OF ELECTRIC SHOCK risk of re or shock hazard DO NOT OPEN do not expose this product to rain or moisture CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER OR BACK NO USER SERICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL The lightning symbol is intended to alert you to the presence of uninsulated dangerous voltage within this productis enclosure that might be of suf cient magnitude to constitute a risk of electric shock Do not open the productis case The exclamation symbol is intended to inform you that important operating2. and maintenace instructions are included in the literature accompanhing this product Features and controls VOLTAGE PYLEPRO e POWER PEAT stereo Power Amplifier 1 Power ON LED Indicator Lights to indicate power is turned on 2 Master Volume Control Lets you adjust the overall sound level 3 RCA Cable L R LINE Input Lets you to connect the desired LINE input source 4 PUSH TYPE SPEAKER L R TERMINALS Lets you easily connect speaker wires directly to the Amplifier 5 Voltage Selector Lets you select the voltage of AC power input source The amplifier has selectable input voltage from 110V 60Hz which is the standard in USA and CANADA You can also switch the input voltage to 230V 50Hz for EUROPEAN operation Please make sure the switch is in the proper position before operating otherwise severe damage will result not cover by the warrnaty Please also replace the fuse with proper rating in this situation see the next instruction for the fuse rating 6 Fuse The amplifier uses a fuse for protection against surges and shor circuit If the amplifier suddenly turns off and will not turn on check the fuse If necessary replace it with a 1 amp 250 volt fast acting 5 x 20mm fuse not supplied 1 FUSE CARING FOR YOUR PYLE PRO AMPLIFIER Your Pyle Pro Amplifier is an example of superior design and craftsmanship The following suggestions will help you care for your amplifier so you can enjoy years of us
3. d or subject to misuse neglect or accidental damage SPECIFICATIONS Output power 2 channels driven 4 OHM 1 KHz 1 THD 3 0Wx2 4 OHM 1 KHz 10 THD 2 2Wx2 Peak Power 5Wx2 Total Harmonic Distortion 1 KHz Rated Power 0 3 Input Sensitivity 1 KHz 4 ohm Rated Power 150mV Frequency Response 20Hz 40KHz Signal to Noise Ratio 75dB Power Requirement 120V AC 60Hz or 230V AC 50Hz Dimensions 142 6x55x107mm WxHxD
4. e Keep the amplifier dry If it gets wet wipe immediately Use the amplifier only in well ventilated installations Handle the amplifier away from dust and dirt Wipe occasionally with a damp cloth to keep it looking new Do not use harsh chemical solvents or detergents IMPORTANT Replacing a fuse This amplifier requires a fuse with the proper rating for protection from power surges and short circuits If the amplifier suddenly turns off or will not turn on the fuse is properly blown Let the amplifier cool down and see if it start again before you assume a fuse needs to be replaced Unplug the amplifier from the AC outlet Turn the fuse holder cap and pull out the cap Remove the old fuse and replace it with an identical one CAUTION Never use a fuse with a higher rating TROUBLE SHOOTING No power No sound The fuse might be blown Sound source or speakers not connected properly MASTER volume control set to minimum The speaker s wire might be the wrong impedance The amplifier might has shut down Check the amplifier s fuse and replace it if necessary Check all connections Adjust the volume control to desired setting Make sure all connected speakers have the same impedance rating Turn the amplifier off and let it cool Make sure the amplifier is properly ventilated and then turn it back on Limited warranty All PYLE PRO products are carefully constructed and t
5. ested before shipment Units purchased in the USA are warranted to be free of defects in material and workmanship for one 1 year from the date of purchase This warranty is limited to the original retall purchaser of the amplifier Should the unitfall due to factory defects in material or workmanship your unit well be repaired or replaced at the sole discretion of PYLE To obtain warranty service you must first call our Consumer Return Hotline at 718 236 6948 to obtain a Return Authorization Number This R A must appear on the outside of your package and on all paperwork relating to your return When returning the unit to us for warranty service it must be carefully packed and shipped prepaid to gt gt R A 2 K PYLE PYLE PRO Service Center PRO 1600 63rd Street Brooklyn NY 11204 You must also include the following items with your return A copy of your sales receipt or other proof of purchase A brief letter indicating the problem you are experiencing with the product Include in your return address daytime phone number and R A number Also include a check or money order for 20 00 for return shipping handling and insurance or provide your Visa MC number with expiration date Our obligation under this warranty is limited to the repair or replacement of the defective unit when it is returned to us prepaid This warranty will be considered void if the unit was tampered with improperly service
Download Pdf Manuals
Related Search