PYLE Audio PDWM4300 User's Manual
Contents
1. check polarities Move the power switch to the ON position The power indicator will be green to indicate normal operation If the LOW BAT indicator turns red replace with a fresh battery promptly Before operation please confirm that the frequency of transmitter is same as the frequency of receiver Plug the 3 5mm connector of headset mic to screw lock socket of transmitter Move the audio switch to ON position The MUTE switch cuts off the audio output without shutting off the transmitter e ATTENUATION is for volume adjustment Move it to OdB position to get normal volume output Move it to 20dB position to reduce distortion and avoid feedback e If the system will not be used for a long time please switch off the transmitter to avoid power consumption RECEIVER FRONT PANEL VOLUME 00000 RF AFLEVEL CHANNEL 2 CHANNEL 1 VOLUME 00000 RF AF LEVEL VOLUME t 00000 RF AF LEVEL CHANNEL 3 CHANNEL 4 13 7 CH 2 AF Indicator 8 CH 3 RF Signal Indicator 9 CH 3 AF Indicator 10 CH 4 RF Signal Indicator 1 Power Indicator 2 Power Switch 3 Antenna 4 CH 1 RF Signal Indicator 5 CH 1 AF Indicator 11 CH 4AF Indicator 6 CH 2 RF Signal Indicator 12 CH 1 Volume Control OPERATION Attach the two antennas andextend them vertically Switch on the receiver The red power indicator will come on Switch on the transmitter The red indicator R2. F Channel1 RF Channel2 RF Channel3 RF Channel4 will come on to indicate signal reception The green AF LEVEL meters indicate the audio level 14 15 16 13 CH 2 Volume Control 14 CH 3 Volume Control 15 CH 4 Volume Control 16 Rack Mounts Adjust the volume of receiver transmitters and amplifier Please switch off the receiver transmitters and amplifier when the wireless microphone system is not being used RECEIVER REAR PANEL 17 Balanced output jack 18 Unbalanced output jack 19 CH 1 Output jack 20 Squelch adjustor 21 DC Power in SQUELCH The squelch control on the rear of the receiver is preset at the factory If you must use the system in an area with considerable RF interference and there is some noise from the receiver when your transmitter is off you can adjust the squelch control so that the system will receive the signal from your transmitter only but squelch or eliminate the unwanted background RF noise This adjustment can DC IN 15V 500mA cause reduction in useable range of the wireless transmitter so set the control to the lowest position that reliablely mutes the unwanted RF signals Note that switching the microphone on and off can cause interference that will be heard if the microphone volume level of the amplifier system is still set high
3. PYLE PDWM4300 PYLE PDWM4300 PRO VHF WIRELESS SYSTEM PRO VHF WIRELESS SYSTEM OPERATION MANUAL OPERATION MANUAL VHF WIRELESS SYSTEM PRECAUTIONS OPERATION MANUAL Thank you for buying the PDWM4300 Wireless System Please read through these operation instructions so you will know how to operate your model properly After you read it put itawayina safe place for future reference Avoid exposure of the system to rain or moisture e No user serviceable parts inside the system Refer all servicing to a qualified technician only Handle the wireless system carefully dropping or other shocks may cause failure Avoid using the system where it may be subjected to heat such as direct sunlight near radiators or other heat sources CONTENTS Should any liquid be spilt on the system stop using it immediately It may be possible to dry the system but you should have it checked by a qualified technician PI Precautions before using it again Take care with the main power adapter and lead If damaged in any way do not use Pe Products figure the system and refer to a qualified technician for repair P3 Hand held microphone Only use the system with the supplied components Do not attempt to use with any Bod kt itt other main power supply adapter ransmitter Zu u vane il e Ifthe wireless system is not going to be used for a while remove the battery to PS Receiver Front panel prevent leakage In the event of electrolyte leakag
4. attery into compartment A howling noise with correct polarities then close the cover 2 Move ON OFF switch to ON position PWR indicator will light for one second and then go off This indicates correct operation If it doesn t come on please check the voltage of battery or polarities If the PWR indicator lights red this indicates the battery power is low Please replace with a fresh battery heard from the speakers The battery in the wireless microphone is weak microphone Replace the battery INSTALLATION Using the supplied audio cable connect from the MIXED jack socket to the MIC IN LINE IN socket on amplifier Alternatively you can connect an optional XLR cable from the XLR MIXED socket on the receiver to a professional mixer Connect the mains power adaptor from DC 15V jack to a suitable mains power socket Installation Location At least 3 ft above ground level At Least 3 ft away from wall ARAS o sesos OJoJoJoJo Ja 000 PROFESSIONAL MIXER MAINS POWER ADAPTER AMPLIFIER RECEIVER O o oo oO 5 sat e MXD ca sos sos sa2 SPEAKERS BODYPACK TRANSMITTER BELT CLIP BATTERY COVER AUDIO OUTPUT JACK VOLUME SWITCH MIC LINE AUDJ POWER ATTENUATION POWER ANTENNA LOW BATTERY LED LG HEADSET MIC POWER LED LAVALIER MIC OPERATION Open the battery cover to install a 9V battery
5. e inside the battery compartment carefully remove the leakage with a damp cloth Take care not to get battery P6 Receiver Rear Panel l FR electrolyte in contact with your skin however if it does wash your hands under a P7 Installation running tap If electrolyte comes into contact with your eyes seek medical advice immediately PS Trouble shooting e Only replace the battery with the same or an equivalent type P9 Specifications Please dispose of old batteries in an environmentally friendly manner in accordance with the relevant legislation Do not use any solvents to clean any part of the wireless system SPECIFICATIONS A Overall system Oscillation mode Quartz controlled Carrier Frequency Range VHF 169 270MHz Stability 0 005 Max Deviation 56KHz with level limiting Dynamic Range gt 100dB S N Ratio 80dB T H D lt 0 5 Squelch Pilotone amp Noise lock dual squelch circuit Frequency Response 100Hz 15KHz Operating range Up to 240 Feet B Receiver Sensitivity 6dB u V at S N gt 90dB Image Rejection gt 60dB Stability gt 80dB Audio output 12db 6000hms unbalanced and balanced Power supply 15VDC 0 5A Dimensions m m 16 5X8 2xX 1 8 inch C Transmitter Mike capsule Dynamic microphone Handheld mic Condenser Microphone Headset mic clip on mic Antenna Built in housing Handheld transmitter External Belt pack transmitter RF Output lt 10mW Spurious lt 40dB Ba
6. ttery one 9V battery 9 SYSTEM DIAGRAM HAND HELD MICROPHONE TROUBLE SHOOTING The wireless microphone is not Turn on the wireless microphone Theana The microphone receiver is not Turn on the microphone receiver a does turned on and the connected audio equipment not light up The microphone receiver is not Turn on the microphone receiver connected properly and the connected audio equipment UNSCREW BATTERY COVER TO INSERT BATTERY TITAN KV EN UNSEREN NN N LEN RRA E KKK XXX CODO AA WYK OXXXK KKK II OEA OX NAAA AAA X OR XQ IA No sound XXX The battery in the wireless The microphone receiver is not Turn on the microphone receiver turned on and the connected audio equipment The connected audio equipment is Turn on the audio equipment not turned on he speakers headphones are not Connect the speakers connected to the audio equipment headphones The battery in the wireless microphone is weak The AUDIO OUT on the receiver is not set correctly Replace the battery The sound is POWER POWER SWITCH BATTERY COVER distorted INDICATOR Adjust the volumecontrols Move the wireless microphone away from the speakers or change the direction of the The distance between the wireless microphone and speakers are too close OPERATION 1 Unscrew the battery cover at the end of microphone put a 9V b
Download Pdf Manuals
Related Search