Premier Mounts PP-FCTA-QL User's Manual
Contents
1. Once the two pieces are together align the mounting holes on the upper adapter plate with the threaded shafts of the lower adapter plate Place the three units together and loosely attach four 4 1 4 20 wing nuts onto the threaded shafts Pre set the M5 x 16 Phillips screws two on each outer ends of the plate and one 1 on the 1 2 NPT coupler Observe the room and the ceiling find the most appropriate location for the projector placement and lightly mark the bottom of the tile Remove any of the 24 x 24 or 24 x 48 tiles that are surrounding the marked tile Measure 3 from the edge of the t bar to the inside of the tile do this for all four edges of the ceiling tile The mounting hole should be located in the center most location of the ceiling tile Once the mounting hole has been cut place the ceiling plate assembly on the t bar rails och PP FCTA QL 1 4 20 Wing Nuts Upper Adapter PA Plate o Mount L A L Wing Nut Threaded Studs Lower Adapter Plate Ceiling Plate Assembly Mounting Hole Installation Instructions PP FCTA QL CA Securing the Plate T Bar Frame Rails Adjust and Tighten Wing Nut M5 x 16mm Set Screw Tiles Step 1 Position and slide the adapter plate to the hole and secure the ceiling plate to the rails by tightening the four 4 M5 x 16mm Phillips head screws Step 2 Center the stud plate to the hole and secure the2. Run the open end through the hole in the eye lag screw Step 4 Run the open end through the loop Step 5 Pull the open end down until the braided cable tightens around the eye lag screw Installation Instructions Page 7 p C4 PP FCTA QL Quick Lock Operation Cable Input directional input arrows To release the braided cable Cable Output A Feed braided cable into the Quick Lock see slide the release pin to disengage Directional Input Arrows Release Pin Directional Input Arrows Braided Cable Braided Cable Braided Cable Braided Cable 6 Excess Directional Input Arrows Directional Input Arrows rp Directional Input I Arrows Release Pin Release Pin Release Pin Release Pin Mounting Hole Mounting Hole Page 8 Installation Instructions gt a PP FCTA QL CA Step 1 Thread each braided cable through the Quick Lock the mounting hole in the corner of ceiling mount and then completely through the opposite side of the Quick Lock to secure A NOTE To relieve tension on the braided cable slide the release pin on the Quick Lock Step 2 Adjust the braided cable tension but do not overtighten Step 3 When adjusting the tension of the weight bearing side of the Quick Lock the cable must be pulled through the Quick Lock until the desired tension is attained Once attained pull the braided cable through the other side of the Quick Lock Step 4 Once the tension ha
3. URPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RE SULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS THE SURFACE MUST BE CAPABLE OF SUPPORTING 250LBS IF NOT THE SURFACE STRUCTURE MUST BE REINFORCED DO NOT HAND OR ATTACH MORE THAN SOLBS TO THIS PRODUCT PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Injury and or damage can result from dropping or mishandling the product If mounting to studs make sure that the mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in the surface or utility pipe Cutting drilling into an electrical line may cause serious injury or property damage This product is intended for indoor use only Use of th
4. b 4 PREMIER Sa MOUNTS The original holding company INSTALLATION INSTRUCTIONS PP FCTA QL Ceiling Adapter NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House Anaheim CA 92806 USA Shilton Industrial Estate anaid candi Shilton Coventry England CV79JY Phone 800 368 9700 Fax 800 832 4888 Phone 44 0 2476 614700 Fax 44 0 2476 614710 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 OPremier Mounts 2008 9533 030 001 01 PP FCTA QL Warning Stafement a scia ai oracle 2 Parts Lists eri wid temennin STINA 3 Installation ToO iere ear aaa ite 3 Plate Assembly ormene reale rota E SARAI SEI ES ERI VIRA REC i ire 4 Securing the PIA 5 Electrical Box Installation i si Ra e eni 5 Ceilinp ADCHOfimig s1s lira RATA 7 Cable Lock Operatii misen poren ire ie 8 Securing Pipe t0 PP FCTA QL iiiilr asru iaaa E E A EE EASE D REA EENE A 10 Technical Specifications sis edsr nus estes annes seeks seas EROE nai aa 10 Waltanly sesanan ROERO ERI OT 11 Warning Statements YP PPOOe 6 09 Page 2 PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR P
5. ent product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DIS PLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUD ING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOV ING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original con sumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mount
6. is product outdoors could lead to product failure and personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Installation Instructions D PP FCTA QL A Parts List This ceiling adapter comes packaged with installation hardware and components Make sure that none of these parts A NOTE are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts 800 368 9700 1 4 20 Wing Nuts Ceiling Adapter i Qty 4 Qty 1 M5 x 16 Phillips Head Screws Qty 5 Quick Locks Qty 4 U G C 14 x 3 Eye Lag Screws Qty 4 SA SZ N Ta a ES SS 1 16 Braided Cable Qty 4 Strands 14 x 3 Concrete Anchors Qty 4 Installation Tools Phillips Head Screwdriver Cable Cutters Ladder Installation Instructions Page 3 Plate Assembly A note Read all cautions and warnings before continuing Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Page 4 Assemble the plate Place the lower adapter plate with the threaded studs on it up through mounting plate The threaded studs will align with the adjustable slide on the mount
7. plate by tightening the four wing nuts Electrical Box Installation Ah nore Electrical installation should be done in accordance to local codes and regulations Step 1 Cut the tile where the electrical base box is going to be secured Step 2 Using commercially available hardware depending on electrical installation environment install the electrical box and secure it to the plate Step 3 Make all electrical connections at this time Electrical Box Cut out Installation Instructions Page 5 Installation Instructions Page 6 PPRCTAQD UA Ceiling Anchoring A Warning THE PP FCTA QL MUST SECURED USING THE SUPPLIED QUICK LOCES AND BRAIDED CABLES Truss Concrete Wood Truss Concrete Wood Joist Eye Lag Hole Loop Eye Lag Hole Loop Braided Cable Braided Cable H e Truss ceiling Concrete Wood joist Step 1 Loop the braided cable Step 1 Determine the mounting Step 1 Secure the four 4 4 eye around the truss location lag screws to the wood joist Step 2 Run the open end through Step 2 Use a 1 4 masonry drill bit in the ceiling the loop to pre drill the mounting Step 2 Make sure eye lag screws Step 3 Pull the open end down until holes are properly secured to the the braided cable tightens Step 3 Place the concrete anchor joist before securing the cable around the truss into the pre drilled hole and to the cable locks on the gently tap into place using a plate rubber mallet or hammer Step 3
8. s Attn Warranty Claim 3130 E Miraloma Avenue Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Installation Instructions Page 11
9. s been adjusted be sure that there is at least 6 of excess braided cable on the non weight bearing side of the Quick Lock Step 5 Use cable cutters to remove any remaining braided cable optional Braided Cable 6 Excess Braided Cable Quick Lock Installation Instructions Page 9 gt Ea PP FCTA QL Securing Pipe to the PP FCTA QL Step 1 Secure the 1 2 NPT pipe to the ceiling plate and tighten by using one 1 M5 x 16 Phillips head screw supplied to the plate A CAUTION The MS x 16 Phillip head screw must be used to stabilize the 112 NPT pipe 1 1 2 Pipe MS x 16mm Set Screw 1 1 2 Pipe Ceiling Plate Assembly Tiles T Bar Frame Rails Technical Specifications All measurements are in inches mm Page 10 Installation Instructions PP FCTA QL Ca Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacem
Download Pdf Manuals
Related Search