POSIFLEX Business Machines LM-/TM-7115/7115N User's Manual
Contents
1. Press NXT button to switch the selection Press OSD button to make the choice a ACCEPT Accept the adjustment setting D REJECT Decline the adjustment setting and return to previous setting AUTO RGB RESET Upon an OSD button press on this icon the monitor will perform an automatic RGB reset and exits the OSD window leaving 2 icons below at center of the screen Press NXT button to switch the selection Press OSD button to make the choice ACCEPT Accept the reset result REJECT Decline the reset and return to previous setting COLOR BALANCE ADJUST When this item is selected there will be 7 icons in this item BBAJ AE between main menu area and the video signal mode Press OSD button to select an item or return to color adjust submenu Press NXT button to select among separate color adjust 4200K 5000K 6500K 7500K 9300K and exit SEPARATE COLOR ADJUST When this item is selected there will be 3 adjustment indication bars between the main menu area and the video signal mode Press NXT button to select among the 3 colors Red Green and Blue respectively Press button to intensify that color Press to reduce Press OSD button to save the current setting and return to Color balance adjust submenu 4200K Pressing OSD button on this icon will set the color balance to a color temperature of 4200 degrees Kelvi2. buttons are above the power switch button on left side of the LCD panel OSD button To enter OSD setup menu or to perform function selected in OSD operation NXT button To go to next option function button To increase setting value button To decrease setting value B OSD functions Press OSD button with a normal display on the screen to activate the OSD functions On Screen Display adjustment The OSD window will pop up on the screen On top part of this window is a Posiflex logo with the OSD firmware version indicated to its lower right Below this area is a row of icons for main OSD menu Below the main menu is a group of icons for submenu that corresponds to one icon selected in the main menu An analysis of the video signal on resolution and refresh rate will be displayed at the bottom Applicable icons in the main menu and its subsequent menus are explained below MAIN MENU There are in total 5 icons in this menu One of the 5 icons will be displayed in inverted color to indicate its De Kase fel relationship with the submenu below Pressing NXT button will shift the selected icon one by one from left to right and then wrap around to the most left Press OSD button to enter the selected sub menu If there is no button for OSD setting is pressed within a period of time about 5 seconds to 1 minute as programmed the OSD window will disappear with all the adjusted parameters sa
3. for any special driver in Windows However there is a program supported for its calibration and touch function manipulation Please find it in the attached Posiflex product information CD ROM under subdirectory Drivers TM_LM USB or select Peripheral Drivers amp Utilities then USB Touch Manager of TM series depending on the version of the CD ROM For Linux environment please find the setup program for the suitable kernel in the same directory and install the required driver and calibration program as the setup program proceeds B SETUP CALIBRATION a USB touch manager For TM 7115 7115N Once the USB control program is installed the user can utilize it to calibrate the touch screen define mouse button emulation parameters enable right button emulation or define the click sound s tone and duration Please go to Program Files and select Posiflex USB Touch Tools and then select Posiflex USB Touch Manager within the tools to engage this utility Most items in this utility should be easily understandable to average user Followings are just some reminders on some items e Calibrate This button engages the Posiflex USB Touch Calibrator e Hide Cursor This button hides or shows the mouse cursor on screen display Please never hide cursor before the touch is enabled and calibrated e Restore Defaults This button resets all touch parameters to default settings Part 5 7 b Ed
4. matter the kit it contains MSR only finger print sensor only or both options the connection to the LM TM 7115 7115N monitor is through an internal cable in right side cover of the LCD touch unit Remove the 2 circled screws in the left picture to remove the cover for side mount upgrade kit as viewed from back of the panel Ww N e Take out the cable inside this cover as circled in the left picture here and connect it to connector inside the side mount upgrade kit as arrowed in the same picture Gently arrange the excessive length p of this cable back in the hole and screw fit c zn it back to the position originally occupied by the cover as in the right picture Please reserve the cover if there is chance to have the side mount kit removed in the future Part 3 C Cable Connections In order to settle the touch monitor properly in a point of sale system all the cable connections have to be routed through its base Therefore please observe the procedures from A to C below to separate the main unit from the base stand assembly after all cables in connection area disconnected Step A Prepare a soft clean flat surface such as a piece of cloth on the desk to seat the front surface of main unit B ope A Step B Press the Lock Release button for main unit detach and meantime _ Step C Slide the base stand assembly to the right to separate the main unit from base Refer to the bottom view picture of
5. that for TM 7115N is 24 bits or 16 2 M colors Supported display modes are as in the table j Refresh Rate Hz a Frequency 40 400 60 640 480 720 400 800 600 1024 768 XI TROUBLE SHOOTING In case of any malfunction please check the following points in sequence to resolve it 1 If there is no power indication please check the power connection 2 If there is no picture display with power LED on please check the video signal connection 3 If there is no touch function please check the connection of the USB cable 21863250800 for USB interface touch controller POSIFLEX S T31454 o SEPANG Grell E gt AEE ERE PERR af BE 3 pk SI E EREET RMS RRR HER lt Part 12 a
6. the separated base at left pass all cable through the dash lined tunnel under a steel plate Open the steel plate if necessary by removing the 2 triangle marked screws Insert the rectangular marked end first when reinstalling the steel plate Hook the main unit back onto base stand assembly by matching the matching pegs to round part of matching holes and slide them down to slot part till the rear lock release button clicks Matching Pegs Matching Holes Round Part Slot Part ao Connect the VGA cable USB cable type B connector and power cable to the I O connection area of LM TM 7115 7115N Connect up to 2 USB devices to LM TM 7115 7115N at the type A connectors Please note that unlike usual USB HUB these USB devices won t be recognized by the host when LM TM 7115 7115N is powered off Part 4 7 E D Option Wall Mount Kit Select a flat surface on wall of adequate strength and with proper ventilation and space condition Please use the right material to hold this monitor according to the wall material Drywall concrete solid wood etc Consult with your contractor if it is necessary Please fix WB 6000V B at the holes inside the guide E a holes circled in the picture to the wall or Front Side Back side fix it to a VESA joint at bosses on back WB 6000V B WB 6000V B side VII DRIVER INSTALLATION A INSTALLATION The USB interface touch controller operates as an USB mouse without need
7. POSIFLEX LM TM 7115 7115N f LCD Touch Monitor User s Manual I FEATURES e Most stable 15 LCD monitor with tilt adjust for industrial and commercial use e Application covers POS Factory Automation etc Rev BO e High quality 15 TFT LCD panel with scaling function for full screen display e Easy maintenance structure allowing easy cleaning e Tilt adjustable yet robust and wobble free construction e Recommended LCD resolution 1024 x 768 e Resistive type extra long life touch panel in USB interface supports touch panel function including left right button double click drag amp drop For TM 7115 7115N e Touch beep can be pitch adjusted enabled disabled by software control For TM 7115 7115N e Connect to host through VGA port plus USB port for all models and or COM port for TM 7115 7115N s RS232 touch model only e Support 2 downlink USB ports FCC NOTICE This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own exp
8. and assembly User s Manual VGA cable USB cable Power adaptor 12 V DC amp power cord Posiflex Product Information CDROM Option RS232 cable Option Audio cable oo Se Sy eS ee lll PARTS IDENTIFICATION A FRONT VIEW Main Unit Display Screen Touch Panel T Logo Power Indicator Adjustable Base Assembly B SIDE VIEWS Lock release button to A detach the main unit a he Control button area Push in this direction to adjust the tilt angle of the display panel OSD button NXT button button button Power switch Lock release lever Part 2 IV INPUT OUTPUT PORTS 12 VDC VGA RJ45 Jack USB B USB A option input input etn a for to Host to Devices Audio input 5 Tz CA USA h jelle usa 1P V AVAILABLE OPTION ITEMS Audio port for multimedia application Side mount upgrade kit FA 200 with MSR Fingerprint sensor Wall mount kit WB 6000V B VI HARDWARE INSTALLATION A Option Multi Media Function When this option is ordered with the LM TM 7115 7115N touch monitor the 3 5 mm diameter stereo jack and 2 internal 2W speakers with amplifiers are already installed This option cannot be late installed if it is not included in the original order B Option Side Mount Upgrade Kit When a side mount upgrade kit option such as FA 200 is ordered with the LM TM 7115 7115N monitor this option is already installed in the delivery No
9. downward Press to go upward Press OSD button to save the current setting and return to OSD submenu E EXIT Return to Tools submenu RESET TO DEFAULT Pressing OSD button on this icon will set all parameters back to the status when the monitor left factory R SMOOTHNESS SHARPNESS ADJUST When this item is selected there will be only the smoothness sharpness adjust icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to increase smoothness of display decrease sharpness Press to go the other way Press OSD button to save the current setting and return to OSD submenu MODE SELECT Pressing OSD button on this icon will have no effect at all if the display mode is not one of the confusing modes The confusing modes here mean 640 x 400 or 720 x 400 in display resolution as both mode have refresh rate of 70Hz horizontal Part 11 frequency of 37 9KHz and pixel frequency of 31 5MHz making it impossible for automatic select These modes are not used in normal Windows display E EXIT Return to Main menu Ki EXIT Exit OSD setup with all adjustment saved X SUPPORTED DISPLAY MODES For video signals beyond the supported display modes there will be a message Out Of Range on middle of screen Maximum supported color depth for TM 7115 is 18 bits or 262 144 colors and
10. ense will be required to take whatever measures to correct the interference WARRANTY LIMITS Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper application ABOUT THIS MANUAL This manual assists the user to utilize the Touch Monitor TM 7115 amp TM 7115N This product provides exquisite touch control capability over a stable and adjustable LCD monitor with minimal footprint The manufacturer of the LM TM 7115 7115N touch monitor heartily apologizes to the user for reserving the right to change or to modify this manual without notice due to the rapid and constant progress and improvement on science and technology The user may always obtain the most up to date information through any of our web sites http www posiflex com http www posiflex com tw http www posiflexusa com Copyright Posiflex Technology Inc 2010 TRADE MARKS AND SERVICE MARKS POSIFLEX is a registered trademark of Posiflex Technology Inc Other brand and product names are trademarks and registered trademarks and service marks of their respective owners P N 19690900030 Part 1 ll CARTON CONTENTS Touch Monitor Main unit Adjustable base st
11. ge Accel This function engages the Posiflex USB Touch Edge Acceleration Tool and helps to find the hidden taskbar or thin scroll bar through touch Enable Touch This check box must be checked to have the touch panel working Enable Touch_to_Calibrate This check box provides a shortcut for touch calibrator by holding touch for a programmed time delay However this function denies the touch mode of Click on Release Enable Buzzer This check box enables the internal buzzer beep as response to touch on touch panel Enable Frequency This selection box selects the buzzer tone by up down arrows beside the box Enable Duration This selection box selects the length for the touch beep by up down arrows beside the box Double Click Area This selection box selects the size of touch point on touch panel by up down arrows beside the box A too small touch size makes the double click operation difficult A too large touch size results in unsatisfactory touch accuracy Time delay to Touch_to_Calibrate This selection box defines the touch time required for a shortcut to Touch Calibrator by up down arrows beside the box when the Enable Touch_to_Calibrate check box is checked Touch Mode Setting Only one of the three radio buttons can be selected The mouse emulation refers to the drag and drop function OK This button accepts all parameters set and closes the utility window Apply This button accepts all
12. is submenu ompa Press OSD button to select item or return to main menu Press NXT button to select among OSD submenu reset to default phase smoothness sharpness adjust mode select and exit OSD SUBMENU When this item is selected there are 4 icons in this submenu PAGE Press OSD button to select item or return to main menu Press NXT button to select among OSD time OSD horizontal position OSD vertical position and exit OSD TIME When this item is selected there will be only the OSD time icon with an adjustment indication bar under it between the main menu area and the video signal mode Press or button to adjust the waiting time for OSD operation before OSD termination between 5 to 60 seconds Default is 30 seconds Press OSD button to save the current setting and return to OSD submenu OSD HORIZONTAL POSITION When this item is ted there will be only the vertical position icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to shift OSD window right Press to shift left Press OSD button to save the current setting and return to OSD submenu OSD VERTICAL POSITION When this item is selected there will be only the vertical position icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to move OSD window
13. n F000 5000K Pressing OSD button on this icon will set the color balance to a color temperature of 5000 degrees Kelvin 6500K Pressing OSD button on this icon will set the color balance to a color temperature of 6500 degrees Kelvin Part 9 7500K Pressing OSD button on this icon will set the color balance to a color temperature of 7500 degrees Kelvin ze 9300K Pressing OSD button on this icon will set the color balance to a color temperature of 9300 degrees Kelvin Hed EXIT Return to Color adjust submenu Ei EXIT Return to Main menu Q GEOMETRY ADJUST SUBMENU There are 6 icons in this submenu HELTE Press OSD button to select item or return to main menu Press NXT button to select among auto geometry adjust horizontal size phase horizontal position vertical position and exit AUTO GEOMETRY ADJUST Upon an OSD button press on this icon the monitor will perform an automatic geometry adjustment and exits the OSD window leaving 2 icons below at center of the screen Press NXT button to switch the selection Press OSD button to make the choice D ACCEPT Accept the adjustment setting Ey REJECT Decline the adjustment setting and return to previous setting HORIZONTAL SIZE When this item is selected there will be only the horizontal size icon with an adjustment indication bar under it between the main me
14. nu area and the video signal mode Press button to increase horizontal size Press to decrease Press OSD button to save the current setting and return to Geometry adjust submenu Q PHASE When this item is selected there will be only the phase adjust icon with an adjustment indication bar under it between the main menu area and the video signal mode Press or button to adjust the pixel synchronization phase for best picture display Press OSD button to save the current setting and return to Geometry adjust submenu HORIZONTAL POSITION When this item is selected there will be only the horizontal position icon with an adjustment indication bar under it between the main menu area and the video signal mode Press or button to shift the screen display to right or left Press OSD button to save the current setting and return to Geometry adjust submenu VERTICAL POSITION When this item is selected there will be only the vertical position icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to shift up the screen display Press to shift down Press OSD button to save the current setting and return to Geometry Part 10 adjust submenu i EXIT Return to Main menu TOOLS SUBMENU When this item is selected there are 5 icons in th
15. parameters set and remains in the utility window Cancel This button discards all changes to the parameters and closes the utility window Help This button provides explanations USB touch calibrator This program helps re calibrating the touch position with the USB mouse emulation Please touch the calibration targets at each corner and a confirmation box that appear sequentially C USB touch edge acceleration tool Helps to find the hidden taskbar or thin scroll bar through touch E Enable Each check box determines whether or not to engage edge acceleration against which edge of screen Margin This list button selects the range to engage edge acceleration toward the edge before the edge is reached Part 6 e Compensation This list button selects the distance to advance the mouse toward edge from touch point d USB touch right button tool This tool differs slightly from the Touch as Right Button Click check box in the USB touch manager When executed there will be a small window of One Shot Right Button appearing on desktop Any touch on the panel right after touching this small window will work like clicking the right button of mouse at that point However the next touch will resume the left button of mouse unless the small window is touched again C APPLICATION LIMITATION The USB touch is not applicable for OS other than Windows as USB mouse is not supported in DOS environment and
16. there is difficulty in engaging driver to convert the coordination system between the static panel and the dynamic mouse in Linux environment The USB touch is also not applicable when the monitor is used to be the extended screen in multiple monitor application In using the MSR of the side mounted upgrade option for reading a magnetic stripe card be sure to insert the card to the bottom with magnetic stripe facing the mark aside the slot The movement of the card can be either inserting the card from the top surface then sliding the card down out of the slot or sliding the card upward from the lower side of the slot till it reaches the top end as long as the card is a standard one A non standard card recorded without complete degaussing prior to recovery may accept only one direction in card reading If the fingerprint sensor option is installed in the side mount kit please find the most comfortable angle for the fingerprint taking operation in consideration of the LCD panel tilt angle and try to align the core of fingerprint in the sensing area Vill LED MODULE INDICATION e Green standby e Blue power on When this touch monitor is turned ON and the LED lights in blue When the VGA signal vanishes the monitor shows No signal for a while and goes into standby mode and LED is green However the touch panel is still operational Part 7 7 IX OSD ON SCREEN DISPLAY SCREEN ADJUST FUNCTION A OSD buttons The 4 OSD control
17. ved Explanations on items in sub menu are as below a BRIGHTNESS CONTRAST ADJUST SUBMENU There are 3 icons in this submenu AJE Press OSD button to select item or return to main menu Press NXT button to select among brightness contrast and exit BRIGHTNESS ADJUST When this item is selected there will be only the brightness icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to increase brightness Press to decrease Press OSD button to save the current setting and return to Brightness Contrast submenu CONTRAST ADJUST When this item is selected there will be only the contrast icon with an adjustment indication bar under it between the main menu area and the video signal mode Press Part 8 button to increase contrast Press to decrease Press OSD button to save the current setting and return to Brightness Contrast submenu gI EXIT Return to Main menu b COLOR ADJUST SUBMENU There are 4 icons in this submenu HEEJ Press OSD button to select item or return to main menu Press NXT button to select among auto color adjust auto RGB reset Color balance adjust and exit AUTO COLOR ADJUST Upon an OSD button press on this icon the monitor will perform an automatic color adjustment and exits the OSD window leaving 2 icons below at center of the screen
Download Pdf Manuals
Related Search