Pontiac 95-3528 User's Manual
Contents
1. page 2 zh ES d 95 3528 DASH DISASSEMBLY i PONTIAC GTO 2004 2006 Meld 95 3528 DASH DISASSEMBLY PONTIAC GTO 2004 2006 6 Remove 2 Phillips screws exposed at the bottom of the center panel sur rounding radio and remove panel Figure E 7 Unclip and remove trim panel sur rounding radio and A C controls 8 Remove 3 Phillips screws holding cage in radio opening Figure F 9 Pull down on the cage from the Opening inside on the top and remove Figure G Continue to final assembly hh LES 95 3528 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Attach the Double DIN brackets to the Double DIN radio unit using the screws supplied with the radio Figure A Continue to final assembly hh LES 95 3528 KIT ASSEMBLY STACKED ISO MOUNT UNITS PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Attach the Double DIN brackets to the stacked ISO mount units using the screws supplied with the units Figure A Continue to final assembly MESA 95 3528 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any u2. INSTALLATION INSTRUCTIONS FOR PART 95 3528 APPLICATIONS PONTIAC GTO 2004 2006 05 3229 KIT FEATURES e Double DIN Radio Provision e Stacked ISO Mount Units Provision KIT COMPONENTS A Double DIN Brackets B Double DIN Trim plate TOOLS REQUIRED Small Flat Blade Screwdriver e Panel Removal Tool e 86 3528 Radio Removal Keys Eu L 1 800 221 0932 J www metraonline com COPYRIGHT 2008 METRA ELECTRONICS CORPORATION G Vus sssses TABLE OF CONTENTS Dash Disassembly Pontiac GTO 2004 2006 1 2 Kit Assembly Double DIN Radio Provision 3 Stacked ISO Mount Units Provision FINGUASSCMOY caevevesacbisavivaseucieauseisedeaenres ces 5 Note Refer also to the instructions included with the aftermarket radio 1 Disconnect the negative battery ter minal to prevent an accidental short 2 Using the radio removal keys pull the factory radio from the dash and dis connect the wiring Figure A d Unsnap and remove the trim panel at the top center of the dash above the A C vents and remove 4 Phillips screws Figure B 4 Remove 1 Phillips screw from inside lower open storage area where center console and dash meet 5 Unsnap and remove center console open center armrest storage com partment and work forward Figure D Continue on
3. aonline com REV 05 07 08 COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST95 3528
4. nused wires to prevent electrical short circuit Re connect the negative battery terminal and test the unit for proper operation Insert and secure the radio bracket assembly into the radio opening using the screws removed in step 8 of disassembly Snap the Double DIN trim plate onto the bracket radio assembly Reassemble in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front o Gray 12V Batt Memory Yellow Right Front Gray Black Dir TEE Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green UU 2 Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 5 95 3528 INSTRUCTIONS 1 800 221 0932 m www metr
Download Pdf Manuals
Related Search