Polk Audio MOMO MM10 User's Manual
Contents
1. polk Custom Enclosed Subwoofers MM10 10 Subwoofer MM12 12 Subwoofer 2 The Bass Master Commands You Please inspect each loudspeaker and its enclosure carefully Notify your Polk Audio dealer if you notice any damage or missing items Keep the carton and packing material They will do the best job of protecting your speakers if they need to be transported Important Information About Warranty amp Installation Your Polk MOMO Custom Enclosed Subwoofer comes in its own enclosure thus the name Do not take the subwoofer out of its enclosure This will void the warranty Please be aware when handling the enclosure that plexiglass damage such as scratches or cracks due to improper installation or misuse is not covered under the warranty for this product Be careful Subwoofer enclosures need to be installed in places where they can operate safe ly and not endanger the occupants of the automobile Do not install the subwoofer enclo sure on your car s rear deck Do not install your subwoofer enclosure on your front dash board or in your passenger seat To get the safest best performance from your Polk MOMO Custom Enclosed Subwoofer we recommend that you put it in your trunk If you have any questions about these issues please call Polk Audio s friendly Customer Service Department Polk Audio Customer Service is available from 9am b6pm EST Monday through Friday at 800 377 7655 US amp Canada only outside the U2. Audio Inc warrants the original purchaser only that this Polk Audio Polk MOMO Product the Product will be free from defects in materials and workmanship for a period of 3 three years from the date of original retail purchase from a Polk Audio Authorized Dealer However this warranty will auto matically terminate prior to the expiration of the 3 three year period if the original retail purchaser sells or otherwise transfers the Product to any other party The original retail purchaser shall herein after be referred to as you To allow Polk Audio to offer the best possible warranty service please fill out the Product Registration Card s and send them to the Factory at the address provided in the Registration Card within 10 ten days of the date of purchase Defective Products must be shipped together with a proof of purchase prepaid insured to the Authorized Polk Audio Dealer from whom you purchased the Product or to Polk Audio 2550 Britannia Blvd Suite D San Diego CA 92154 Products must be shipped in the original shipping container or its eguivalent in any case the risk of loss or damage in transit is to be borne by you If upon examination at the Factory or Polk Audio Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during the Warranty period Polk Audio or the Polk Audio Dealer will at its option repair or replace this Product at no additional charge except as
3. music Contrary to popular belief a speaker is more likely to be damaged by trying to get too much volume from a low powered amp than from a high powered one Hear distortion Turn it down Contact Polk Customer Service 800 377 7655 9am 6pm EST Monday through Friday Low Frequency Cut Off For Mid Range Speakers In Systems With Subwoofers Now that you have a subwoofer in your system you may want to decrease the amount of bass going to your mid range speakers This will get you better mid range sound and increase the power handling There are two ways to roll off the bass before it gets to your mid range speakers One way is to use a bass blocker a capacitor placed in series with the speaker input Bass blockers are installed in series one end connected with the positive lead from your amplifier and the other end connected to the positive lead of each of your speakers Bass blocker capacitors 200 microfarad 100volts non polarized are available at any RadioShack or parts supply house The other route is to use an electronic crossover device that allows filtering below 100Hz or so Find these devices at your authorized Polk Audio dealer Bass Blocker aaa O H or Capacitor O H adio AMP Speaker C C POLK AUDIO MOMO DESIGN i 5 6 Tech Assistance Or Service Not Hearing Anything Read This If after following these hookup and installation directions you experience difficulty please double check all wire connec
4. not secured Once you have found the best location use the enclosed mounting brackets to secure the subwoofer enclosure to the body of your car Use the screws included only to attach the bracket to the subwoofer enclosure Attach the brackets to the bottom of the enclosure only No screws are provided for car body mounting purposes due to various types of trunk mate rials The installer needs to choose the appropriate screw type and length for the intended trunk mounting application The installer must be careful when drilling into the car struc ture not to damage any important elements fuel lines electrical conduits you know stuff like that Polk Audio takes no responsibility for damage done to car structures when securing this product If you are at all uncertain about the best and safest way to install your subwoofer enclosure consult your local Polk Audio dealer or professional installer Break It In Your Polk MOMO Custom Enclosed Subwoofer will achieve even greater performance once it is thoroughly broken in To break in your new custom enclosed sub play 20 to 30 hours of music at moderate levels Get more information online at Polk University http www polkaudio com car faqad index php Amplifier Power Requirements For Polk MOMO Custom Enclosed Subwoofers With one subwoofer we recommend an amplifier with a power rating of at least 200 Watts x 1 in bridged mode to sufficiently drive this woofer If you have a noisy car or inte
5. set forth below All replaced parts and Products become property of Polk Audio Products replaced or repaired under this Warranty will be returned to you within a reasonable time freight prepaid This Warranty does not include service or parts to repair damage caused by accident disaster misuse abuse negligence inadequate packing or shipping procedures commercial use voltage inputs in excess of the rated maximum of the unit cosmetic appear ance of the cabinetry not directly attributable to defects in materials or workmanship or service repair or modifications of the Product which has not been authorized or approved by Polk Audio This Warranty is in lieu of all other expressed Warranties If this Product is defective in materials and workmanship as warranted above your sole remedy shall be repair or replacement as provided above In no event will Polk Audio Inc be liable to you for any incidental or consequential damages arising out of the use or inability to use the Product even if Polk Audio Inc or a Polk Audio Dealer has been advised of the possibility of such damages or any other claim by any other party Some states do not allow the exclusion or limitation of consequential damages so the above limitation and exclusion may not apply to you This Warranty gives you specific legal rights which may vary from state to state This warranty applies only to Products purchased in the United States of America its possessio
6. S please call 410 358 3600 Connecting Your Polk MOMO Custom Enclosed Subwoofers The push terminal connectors are located on the underside of the Custom Enclosure Because of this placement it is best to use a bare wire or pin connection For a bare wire connection strip 1 2 inch 12 7mm of insulation from each of the two conductors of your wire to expose the bare metal and twist each of the conductors into a single unfrayed strand so you have two unfrayed strands Note that one of the terminals on the enclosure is red and the other is black Make certain that you connect the wire from the red terminal of your amplifier to the red terminal on the enclosure and the wire from the black terminal of your amplifier to the black terminal on the enclosure Most wire has some indicator such as color coding ribbing or writing on one of the two conductors to help you maintain consistency To connect the bare wire to the push terminal apply pressure to the terminal and insert the bare wire into the hole near the base and release Do not insert the insulated part of the wire into the hole as this will not give you a good connection Place the Custom Enclosure right side up making certain that the wire runs through the wire canal on the underside of the enclosure Be careful not to let the full weight of the enclosure rest on the wire POLK MOMO CHAMPIONSHIP PERFORMANCE Wiring Diagrams For Polk MOMO Custom Enclosed Subwoof
7. ers Please make certain that your amplifier is rated to carry the specified load I f Parallel 2 Wiring Two 4Q speakers will present a 2Q load Make sure that your amplifier is 2Q stable when configured in the bridge mode Consult your amplifier s owner s manual before wiring in this configuration Single 42 Wiring Put It In Your Trunk Place your Polk MOMO Custom Enclosed Subwoofer in your trunk or hatchback Experi ment to find the best location for your new subwoofer Subwoofers in trunks or hatchbacks can fire either forward or backward for best sound Positioning can make a big difference in sound quality MM12 8 MM10 MOUNTING BRACKET INSTALLATION O INSTALL BRACKET 8 SCREWS REMOVE SCREWS WARNING This Product MUST Be Secured When Installed POLK AUDIO MOMO DESIGN i 3 4 Permanent mounting is not only the safest installation but usually produces the best sound quality This Custom Enclosure is heavy and has a smooth surface finish and can slide around in a trunk during aggressive driving or a collision if unsecured This could result in damage to the enclosure or the car Use either the mounting brackets provided or if you do not wish to drill into your car body use a couple of large well placed pieces of industrial strength hook amp loop fastener attached to the enclosure and the trunk surface Polk Audio takes no responsibility for damage done to car structures if this product is
8. nd to play your system at loud listening levels more power is necessary to achieve the best performance More power is always better Consult your Polk Audio dealer for specific recommendations Optimal Crossover Setting We recommend using an active crossover with a 12 to 18dB per octave low pass filter slope and setting it to an initial setting of 80 to 90 Hz as a good starting point This is an optimal crossover setting on most vehicles POLK MOMO CHAMPIONSHIP PERFORMANCE Inverting Phase Depending on the placement of your custom enclosure and associated components it may be necessary to invert the phase of one or another of your system s connections in order to sain better subwoofer mid range blending Inverting the phase simply means switching the positive connections with the negative connections at the amplifier If you choose to do this invert the phase of only one set of speakers either your mains or your subs never both Safe Limits Of Operation Your Polk MOMO Custom Enclosed Subwoofer is made with the highest quality materials for years of trouble free performance However damage to loudspeakers can occur when an amplifier regardless of its wattage is made to play at higher listening levels than its power can clearly produce usually beyond the 1 to 2 o clock position on the volume control This results in very high levels of audible distortion originating in the amplifier which adds a harsh gritty sound to the
9. ns and U S and NATO armed forces exchanges and audio clubs The Warranty terms and conditions applicable to Products purchased in other countries are available from the Polk Audio Authorized Distributors in such countries Attach your receipt here and file for future reference It may be required for warranty service X POLK AUDIO MOMO DESIGN i 7 polk mamo 5601 Metro Drive Baltimore Maryland 21215 800 377 7655 http www polkaudio com Polk Polk Audio and The Speaker Specialists are registered trademarks of Polk Investment Corporation used under license by Polk Audio Incorporated MOMO is a registered trademark of MOMO Design Italy CE
10. tions Make certain your electronic equipment is operating correctly by hooking up another speaker to the speaker output For example if you are not getting sound from the left channel speaker connect the right channel speaker to the left output If you still get no sound from that side the problem is in your amp or source electronics Should you isolate the problem to the speak er contact the authorized Polk Audio dealer where you bought your speakers Authorized Polk Audio dealers are the best source for advice and assistance Polk Audio s Customer Service Department is available from 9am b6pm EST Monday through Friday at 800 377 7655 US amp Can only outside the US call 410 358 3600 Please do not hesitate to call us if you have questions about your speaker system We positively love this stuff You will find additional information informative articles manual updates and cool stuff to buy that has Polk Audio all over it by visiting www polkaudio com Polk MOMO Custom Enclosed Subwoofer Specifications MM10 MM12 a ask ee ee 00207222 ak renee a ee ki ee Tue 7 TAAS et ie cae a ane ee ee a nom pees ee a 2020 a aa kol 2021 ORR R 0220 r Polk Audio s Customer Service Department is available from 9am 6pm EST Monday through Friday at 800 377 7655 Please do not hesitate to call us if you have guestions about your speaker system POLK MOMO CHAMPIONSHIP PERFORMANCE Polk MOMO Series 3 Year Warranty Polk
Download Pdf Manuals
Related Search