Polk Audio DR-3 User's Manual
Contents
1. the DR 3 button by button There are tables on pages 14 15 that list the major audio video brands and their three digit remote codes Quick Instructions 1 Look up code number 2 Turn on equipment 3 Press and hold CODE until the Status Light glows red 4 Press Source Device button 5 Enter code number 6 Press SAVE Detailed Instructions 1 Look up the type and brand of equipment you wish to duplicate in the tables that appear on pages 14 15 in this manual For exam ple if you wish to program the DR 3 to operate a Panasonic VCR go to the VCR chart on page 15 and find the code s for Panasonic It might be a good idea to jot that number down on this page so you have it handy as you move through the programming steps Note If there is more than one three digit number listed for your brand try one code number at a time until your equipment turns off after the last step in the programming process When your equipment turns off you have selected the right code You can also verify that you have programmed the correct three digit number by pressing the SOURCE POWER button Your equipment should turn On and Off 2 Turn on the equipment you wish to program NOTE From here on in you have 20 seconds to perform each step If the Source Device button light goes off you need to back up a step and do it again You can exit the set up mode by pressing the CNCL cancel button at any time in the process 3 Press and hold the CODE2. Suite D San Diego California 92154 Products must be shipped in the original shipping container or its equivalent in any case the risk of loss or damage in transit is to be borne by you If upon examination at the Factory or Polk Audio Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during this Warranty period Polk Audio or the Polk Audio Authorized Dealer will at its option repair or replace with new or reconditioned parts this Product at no additional charge except as set forth below All replaced parts and Products become the property of Polk Audio Products replaced or repaired under this warranty will be returned to you within a reasonable time freight prepaid This warranty does not include service or parts to repair damage caused by accident disaster misuse abuse negligence inadequate packing or shipping procedures commercial use voltage inputs in excess of the rated maximum of the unit cosmetic appearance of cabinetry not directly attributable to defect in materials or workmanship or service repair or modification of the Product which has not been authorized or approved by Polk Audio This warranty shall terminate if the Serial number on the Product has been removed tampered with or defaced This warranty is in lieu of all other expressed Warranties If this Product is defective in materials or workmanship as warranted above your sole remedy shall be repair or repl
3. a step and do it again You can exit C by pressing the CNCL cancel button at any time in the process 1 Press and hold the LEARN button for two seconds The status light at the top left of the remote will glow orange pollcaudio 2 Press the Source Device button you wish to erase 2 The Source Device button light will turn on 3 Press and hold the LIGHT button for 5 seconds until the status 3 light flashes red five times and then flashes green twice and the Source Device button turns off The status light will go to a constant orange indicating that all the learned information on buttons in the Source Device mode have been erased The Source Device button will turn on 4 save your changes press the SAVE button The orange status light will flash twice and then turn off The Source Device button DMG will turn off JIG 10 Polk Customer Service 800 377 7655 PROGRAMMING THE REMOTE Erasing All the Learned Commands in All Device Modes This procedure will erase all the learned commands on all the buttons in all eight Source Device modes Be really really sure you want to do this before following the steps below 1 Press and hold the LEARN button for two seconds The Status light at the top left of the remote will glow orange 2 Press and hold
4. shown in the illustration 1 Press and hold the LEARN button on the DR 3 for two seconds The status light at the top left of the remote will glow orange 2 Select the Source Device mode in which you would like to teach the new command The Source Device button will light up For example if you wanted to teach a command to the MENU button in the DSS mode on the remote you would select the DSS Source Device button and then continue the instructions below to teach the new command to the MENU button 3 Press the button on the DR 3 that is to be taught the new com mand The orange status light will begin to flash continuously The Source Device light will turn off 4 On the source remote control original equipment remote control press and hold the button for the command to be learned until the status light on the DR 3 remote turns green 5 Release the button on the source remote control 6 Press the button on the source remote control once again to verify that the new command has been learned correctly The status light on the DR 3 will flash green twice and then turn to a steady orange color to indicate that the programming was successful The Source Device button will light 7 Repeat Steps 3 through 6 for any other buttons to be taught in the device mode selected in Step 2 8 Press and hold the SAVE butto
5. the DVD s main menu to change the audio type This feature may not work with all DVDs and players 3 O NAVIGATION These buttons allow you to move among setup menus to select operations For example if you are looking at a DVD s main title menu and you want to move to the Scene Selection menu push the appropriate arrow button to move to the Scene Selection graphic on the TV screen 24 BK SLOW With most DVD players use this button to make the DVD play at a slower than normal speed backwards 25 SLOW QO With most DVD players use this button to make the DVD play at a slower than normal forward speed 26 ANGLE Acts to toggle between available camera angles on selected DVDs Acts as the Live TV button on TIVO type boxes 27 ZOOM This button serves as the Zoom button with DVD players that have a zoom feature 28 Program Area These four buttons allow you to program in the codes for other remotes or teach the remote specific commands They cannot be reprogrammed for any other functions See pages 7 11 for specific programming instructions 29 SOURCE POWER This button acts as the on off button for the other components in your system once you have entered their remote codes into the DR 3 See pages 7 11 to learn how to pro gram the DR 3 to operate other devices 30 SYSTEM POWER This button turns on and off the Digital Solution system only This function does not change when you enter progr
6. to previous DVD chapters or CD tracks With a TV it acts as the Display button to call up the channel time and other on screen display data With DSS cable boxes and TIVO type devices it calls up the programming guide screen www polkaudio com Status Light TWICE TO TOOGLE SOURCE A WN moe SET UP DVD MENU SUB TTL SELECT NAVIGATION PROGRAM CODE SAVE CNCL LEARN SOURCE POWER SYSTEM POWER MACRO 8 MENU gt l This button acts as chapter skip button to skip forward through DVD chapters or CD tracks With TVs and other video devices it calls up the device menu 9 PAUSE This button acts as the pause step frame button for the DP 1 CD DVD player VCRs CD players and TIVO type video storage devices To return to normal play press the PLAY button With DSS and cable tuner boxes and the Multi room function of the Digital Solution system it acts as the up arrow navigation button for the on screen display 10 REW With DVD CD VCR and TIVO type players this button acts as a rewind or back button For DSS cable boxes TVs and the Multi room function of the Digital Solution system it acts as the left navigation button for on screen displays 11 ENTER PLAY With DVD CD VCR and TIVO type players this button acts as a Play button With all devices it acts as the Enter button to select items on an on screen display 12 FF Wi
7. to select the DVD s power command 9 Press and hold the SAVE button until the red status light and the Source button lights will blink twice and then turn off to confirm the program N In this example the sequence is important The DVD turn on command should be the last command in the Macro string so that the Digital Solution system s input is on Factory Reset If you want to restore the DR 3 to it s original programming and operation press the LIGHT and POWER buttons simultaneously for 10 seconds The red status light will blink while the remote is resetting It will confirm the reset by blinking green and then orange www polkaudio com PRESS TWICE TO TOGGLE SOURCE BCH 2 7 13 Manufacturer Brand Set Up Code Number Manufacturer Brand Set Up Code Number Tape Aux Cable TV PHILIPS TIVO 001 SPECTRICON 112 SONY TIVO 002 555 004 043 DVD Plaver SYLVANIA 001 003 059 060 063 064 GOLDSTAR 057 074 091 AONE E HARMAN KARDON 084 FANCY HITACHI 101 TATUNG 056 062 012 TECHNICS 034 080 LG 057 074 091 TECHWOOD 004 MAGNAVOX
8. will blink e polkaudio N Ww on Finding the Three Digit Code Number for a Device If you are curious which three digit code was auto assigned to a given Source button follow these steps CO 1 Turn on the equipment you wish to operate 2 Press and hold the CODE button for two seconds The red status light at the top left of the remote will turn on 3 Press the Source Device button for which you want to find the 3 three digit number The Source Device button light will turn on 4 Press the GUIDE button The red status light and Source button will blink indicating the number for each digit of the three digit code number Each digit is separated by a 1 second off interval of the light Example One blink LIGHT OFF Three blinks LIGHT OFF and Eight blinks indicates that the three digit code number 138 is stored in the remote for that device Note Ten blinks are equal to the number 0 e polkaudio 8 Polk customer service 800 377 7655 PROGRAMMING THE REMOTE Teaching Method From time to time the three digit programming method doesn t automatically program in all of the commands of the original remote In such cases you can teach the DR 3 individual commands from your original equipment remote cont
9. you enter program codes for other devices 18 Tune SET UP Acts as the manual tune up the dial control for the radio of the Digital Solution system and calls up the Setup menu of a DVD player For the function on other devices see the chart on page 6 19 SCAN DVD MENU With the Digital Solution tuner this acts as the Preset Scan button With DVD players it calls up the DVD software menu 4 Polk customer service 800 377 7655 10 13 14 16 polkaudio PRESS TWICE TO TOGGLE SOURCE AUX 6CH DSS DIG CBL DIG AM SURROUND VOL 12 ri 15 17 18 DVD MENU SUB TTL 19 PROGRAM CODE SAVE CNCL LEARN SOURCE POWER SYSTEM POWER MACRO 20 50 TTL Use to manually tune the radio on the Digital Solution system Acts as the Subtitle toggle switch on DVD play ers For the function on other devices see the chart on page 6 21 SELECT This button selects a choice on a menu such as the set up menu of a DVD player or the title menu of a DVD disc With DSS and cable boxes it acts to call up Favorites It has no function with the Digital Solution preamp processor 22 AUDIO This button toggles through the available audio tracks on a DVD For example if a DVD disc has a 2 Channel audio track a Dolby Digital 5 1 and a French language track each time you push this button the next available audio track will play This eliminates the hassle of going back to
10. you have selected on the DR 3 remote you can always adjust the DS system volume subwoofer level mute and surround mode functions 2 LIGHT Back lights the remote buttons for 8 seconds so you can operate the remote in the dark The function of this button does not change when you enter program codes for other devices 3 MUTE Mutes the sound of the Digital Solution preamp proces sor system To disengage the mute function and go back to normal playback volume press the MUTE button again or press either of the VOLUME buttons The function of this button does not change when you enter program codes for other devices 4 SURROUND MODE This button toggles between the various audio modes of the Digital Solution system such as stereo Dolby Pro Logic 5 Channel Surround etc The function of this button does not change when you enter program codes for other devices 5 VOL These buttons control the volume of the Digital Solution preamp processor The functions of these buttons do not change when you enter program codes for other devices 6 CHNL With the Digital Solution system these buttons step through the preset radio stations just like the Radio Preset rocker buttons on the DR 2 remote included with the DS System With other TV devices TV cable boxes VCR etc these buttons act as channel up and down buttons 7 GUIDE lt With DVD and CD players this button acts as a chapter skip button to skip back
11. 066 096 TEKNIKA 003 004 024 028 043 MARANTZ 083 095 072 101 143 MITSUBISHI 017 TELERENT 072 MYRYAD 102 TERA 172 NAD 088 TMK 004 NAKAMICHI 103 TOSHIBA 015 030 040 062 101 ONKYO 035 076 TOTEVISION 143 PANASONIC 021 042 UNIVERSAL 008 PHILIPS 066 083 095 VIDEO CONCEPTS 146 PIONEER 023 092 099 107 108 VIDIKRON 174 POLKAUDIO 001 VIDTECH 004 PROCEED 086 VORK 004 PROSCAN 026 027 WARDS 004 008 009 019 028 RCA 026 027 060 061 063 064 072 074 164 SAMSUNG 056 070 WESTING HOUSE 076 SHARP 094 YAMAHA 001 004 SONY 033 YUPITERU 043 TATUNG 102 ZENITH 072 073 095 103 THOMPSON 026 027 ZONDA 112 TOSHIBA 034 035 042 089 CARVER 167 041 135 138 139 050 203 ZENITH 057 074 091 DENON 205 226 DSS Player FISHER 016 ECHOSTAR 006 047 033 208 046 HITACHI 011 012 JVC 136 163 004 HUGHES 003 022 031 KENWOOD 007 055 023 137 016 MITSUBISHI 003 022 MARANTZ 044 041 PANASONIC 013 MONDIAL 147 RCA 001 014 015 NAD 215 005 178 SONY 004 NAKAMICHI 218 TOSHIBA 003 008 NIKKO 046 Cable Cable ONKYO 038 168 030 062 169 GENERAL INSTRUMENT 201 230 PANASONIC 068 172 HAMLIN 216 218 223 PHILIPS 041 JERROLD 211 222 229 PIONEER 010 020 174 NSC 220 221 RCA 017 021 OAK 209 217 224 226 227 228 REALISTIC 187 PANASONIC 213 215 SANSUI 171 PIONEER 208 231 232 SHARP 051 173 REGENCY 219 SHERWOOD 166 096 SCIENTIFIC ATLANTA 202 206 212 214 233 SONY 203 210 TEAC ZENITH 204 207 225 TECHNICS 068 008 172 VICTOR 004 YAMAHA 012 186 183 046 ZENITH 204 2
12. 07 225 14 Polk customer service 800 377 7655 Manufacturer Brand Set Up Code Number Manufacturer Brand Set Up Code Number VCR VCR AIWA 034 161 OPTONICA 053 054 AKAI 043 046 124 142 146 PANASONIC 031 070 133 140 AMPRO 072 PENTAX 004 020 031 063 ANAM 031 103 PHILCO 031 034 067 AUDIO DYNAMICS 012 023 043 PHILIPS 031 067 034 054 101 BROKSONIC 035 037 129 PILOT 101 CANON 028 031 PIONEER 004 021 048 CAPEHART 108 PORTLAND 108 CRAIG 001 040 135 PULSAR 072 CUIRTIS MATHES 031 041 QUARTZ 014 DAEWOO 117 005 116 010 017 108 RADIO SHACK 101 123 DAYTRON 108 RCA 144 147 107 109 031 004 020 DBX 012 023 043 034 040 041 140 158 REALISTIC 001 008 010 014 031 034 040 DYNATECH 034 053 11 ELECTROHOME 059 age EMERSON 006 029 035 153 017 025 005 116 027 031 034 036 037 046 RUNCO 072 101 129 131 138 SALORA 014 FISHER 001 008 009 010 SAMSUNG 017 040 107 109 113 115 124 FUNAI 034 SANSUI 043 048 135 GE 031 063 072 107 109 144 147 SANYO 001 010 040 014 134 GO VIDEO 132 136 151 SCOTT 017 037 129 131 GOLDSTAR 004 012 020 101 123 SEARS 017 081 001 004 008 009 010 HARMAN KARDON 012 045 014 020 101 HITACHI 026 150 018 034 043 063 137 SHARP 053 031 054 165 INSTANTREPLAY 031 SHINTOM 024 031 S
13. AY PLAY SELECT PLAY GUIDE I lt lt SKIP SKIP GUIDE SKIP MENU gt gt 1 SKIP SKIP MENU SKIP REC DISC gt Clear Clear EXIT DISC gt RECORD TVIVCR OPEN CLOSE OPEN CLOSE TV DSS OPEN CLOSE VCR TV 1to0 1100 1100 1100 1100 PLUS10 PRE CH REPEAT SCAN DVD MENU PRE SCAN TOP MENU MENU ENTER SCAN SUB SUB SUB SUB SUB SUB SUB SUB SUB SUB SUB SUB TUNE SET UP TUNE SET UP ALT TUNE SUB TTL TUNE SUB TTL UB TTL NEXT Select SELECT FAV LEFT LEFT INFO UP 0 UP RIGHT RIGHT ANGLE ANGLE ANGLE AUDIO AUDIO PLAY MODE BK SLOW BK SLOW ETURN DOWN SLOW R DOWN DOWN SLOW SLOW ZOOM ZOOM CODE CODE SAVE SAVE CNCL CNCL LEARN LEARN SYSTEM POWER POWER SOURCE POWER POWER MACRO MACRO Polk customer service 800 377 7655 PROGRAMMING THE REMOTE Manual Three Digit Code Method The DR 3 remote control can duplicate the remote functions of most brands of audio video equipment by simply entering in a three digit code number When you enter in the code the DR 3 learns most or all of the remote functions of that equipment so you don t need to program
14. DR 3 UNIFIED LEARNING REMOTE CONTROL INSTRUCTION MANUAL Table of Contents DR 3 Remote Guided Tour 2 2222 3 5 Button Function Charten 6 Programming the Remote Manual Three Digit Code Method ccccsssecssrsseesesees 7 Auto aaia 8 Finding the Three Digit Code Number for 8 Teaching Method 2 2 2 40 9 Erasing Learned Command From Button 10 Erase All Learned Commands in One Source Device 10 Erase All Learned Commands in All Device 5 11 Restoring Factory PrograMMing vcs 11 Macro Operation Programming the Macro BUTON isiin eini 12 Macro Sequence 12 Macro Programming Example 13 Setup Codes Chart nissin 14 15 INTRODUCTION The Polk Audio DR 3 Unified Learning Remote was designed to operate the Polk Audio Digital Solution home theater system and Polk Audio DP 1 CD DVD player It can also be programmed to operate most DVD and CD players TVs Cable and DSS tuners as well as VCRs By following the easy steps in this manual you can reduce or eliminate the need for having several remote controls on your coffee table As nifty as it may be the DR 3 unified remote cannot duplicate every function of every remote control without turning it into a nightmare of t
15. ONY 056 057 058 001 009 031 052 053 155 002 CPENNY 004 012 040 101 SOUNDESIGN 034 JENSEN 043 A is a SYLVANIA 031 034 059 067 KENWOOD 014 034 048 047 SYMPHONIC 034 LLOYD 034 TANDY 010 034 LXI 034 001 004 009 017 101 TATUNG 043 MAGIN 040 TEAC 034 043 MAGNAVOX 067 031 034 041 068 154 164 TECHNICS 031 070 MARANTZ 067 069 012 031 TEKNIKA 031 034 101 MARTA 101 THOMAS 034 MATSUI 027 TMK 006 MEI 031 TOSHIBA 017 131 004 008 059 MEMOREX 040 101 001 010 014 031 034 053 072 134 139 TOTEVISION 040 101 MGA 045 046 059 UNITECH 040 MINOLTA 004 020 VECTOR RESEARCH 012 MITSUBISHI 059 061 004 020 046 051 142 VICTOR 048 MTC 034 040 VIDEO CONCEPTS 012 034 046 141 MULTITECH 024 034 4 0 WARD 1 004 017 024 031 034 04 055054 11 WESTINGHOUSE 005 YAMAHA 012 034 043 ZENITH 072 034 048 056 058 080 101 153 www polkaudio com 15 RM2070 1 polkaudio he speaker specialists 5601 METRO DRIVE BALTIMORE MARYLAND 21215 USA 410 764 5275 FAX 410 764 5266 www polkaudio com
16. acement as provided above In no event will Polk Audio Inc be liable to you for any incidental or consequential damages arising out of the use or inability to use the Product even if Polk Audio Inc or a Polk Audio Authorized Dealer has been advised of the possibility of such damages or for any claim by any other party Some states do not allow the exclusion or limitation of consequential damages so the above limitation and exclusion may not apply to you All implied warranties on this Product are limited to the duration of this expressed Warranty Some states do not allow limitation on how long an implied Warranty lasts so the above limitations may not apply to you This Warranty gives you specific legal rights and you also may have other rights which vary from state to state This Warranty applies only to Products purchased in the United States of America its possessions and U S and NATO armed forces exchanges and audio clubs The Warranty terms and conditions applicable to Products purchased in other countries are available from the Polk Audio Authorized Distributors in such countries Polk Audio and The Speaker Specialists are trademarks of Britannia Investment Corporation used under license by Polk Audio Incorporated 2 Polk customer service 800 377 7655 DR 3 REMOTE GUIDED TOUR See the chart on page 6 for the functions of each button with various device types 1 Source Device Area These buttons serve two
17. am codes for other devices 31 MACRO The MACRO button can send out a sequence of up to 20 commands with one button press It can be programmed for up to eight Source buttons This allows you to perform multi step operations with just one button push For example you can pro gram the MACRO button to turn on the TV turn on the DS system turn on the DVD player select the correct Video input and open the DVD drawer with the push of just one button See pages 12 13 for Macro programming instructions T RERS TWICE TO TOGGLE SOURCE ES DIG cS DIG SET UP Mmm DVD MENU SUBTTL 20 26 21 25 28 31 SELECT NAVIGATION 21 23 22 24 PROGRAM CODE SAVE CNCL LEARN SOURCE 29 30 www polkaudio com 5 DR 3 FUNCTION LIST Button Name TAPE AUX Toggle DVD 6CH Polk DVD Others CBL CBL DIG CBL TV AUX TAPE DVD 6CH Toggle DSS DSS DIG Toggle CBL CBL DIG Toggle FM AM Toggle cD MULTI VCR LIGHT LIGHT LIGHT MUTE MUTE MUTE SURROUND MODE MODE MODE VOL UP A VOL UP VOL UP VOL DN V VOL DN VOL DN CHNL UP A PRESET UP CH DN V PRESET DN CH UP PAUSE PAUSE PAUSE UR DOWN STOP v STOP STOP DOWN RIGHT FF gt SCAN SCAN RIGHT FF LEFT REW lt SCAN SCAN LEFT REW ENTER PLAY PL
18. button for two seconds The red status light at the top left of the remote will turn on 4 Press the Source Device button you wish to program e g VCR DVD etc The Source button will light up In the case of the Panasonic VCR example you would push the VCR Source button 5 Point the Polk DR 3 remote control toward the equipment and enter the first listed three digit code number of your brand of equipment The Status light and the Source Device button will blink once for each button pressed The equipment will turn off when you enter the correct three digit number 6 Press and hold the SAVE button for 2 seconds to store the three digit number The Status light and the Source Device button light will blink twice to confirm that the code has been stored and then turn off 7 Try all the functions on the remote control NOTE If any of the functions do not work as they should repeat the programming process using the next three digit code number assigned to your brand If only one or two buttons don t work right it may be easier to individually teach the DR 3 those commands see page 9 or use the Auto Search method see page 8 rather than trying all the three digit codes www polkaudio com e polkaudio PROGRAMMING THE REMOTE Auto Search Method If none of the three digit code numbers assigned to your brand shut o
19. ect either the 6 Channel or the DVD input but only 1 Macro Before you begin the Macro programming process you first have to program all of your system s equipment into the DR 3 remote Use any of the methods described earlier in this manual to fully program the DR 3 remote It is a good idea to use your DR 3 remote for a few days to familiarize yourself with its basic operation before setting up MACRO operations Planning the sequence of commands is very important For example some devices especially TVs will not accept other commands until they are fully turned on You may have to turn on all the devices first then give them other commands later in the sequence You may need to try different command sequences to get to the right result See the example on page 13 to get a feel for programming a Macro NOTE You have 20 seconds to perform each step If the Source button light goes off you need to back up a step and do it again You can exit the set up mode by pressing the CNCL cancel button at any time in the process 1 Press and hold the CODE button for two seconds The status light at the top left of the remote will turn red 2 Press the desired Source Device button The button will light up 3 Press the MACRO button The status light and the Source Device button will blink once 4 Press up to 20 commands you would like to include in the macro sequence starting with the Source button Pressing a Source button to cha
20. ff your equipment or if your brand of equipment is not listed in the code tables you can use the Auto Search Method to find the correct three digit number for your equipment 1 Turn on the equipment you wish to program NOTE From here on in you have 20 seconds to perform each step If the Source Device button light goes off you need to back up a step and do it again You can exit the set up mode by pressing the CNCL cancel button at any time in the process Press and hold the CODE button for two seconds The red status light at the top left of the remote will turn on Press the Source Device button you wish to program e g VCR DVD etc The Source Device button light will turn on 4 Press and hold the CH UP or CH DOWN button The remote will emit series of Power On OFF code signals that are stored in its memory Release the CH button as soon as the equipment turns off You can verify that you have chosen the correct code by pressing the SOURCE POWER button the device should turn On and Off The status light and the Source Device button will blink Press and hold the SAVE button for two seconds to store the code The status light and the Source Device button light will blink twice and then turn off to confirm that the code has been stored Note You can verify that you have chosen the correct code by press ing the SOURCE POWER button the device should turn On and Off The status light and the Source Device button
21. functions to select the device that the remote will control and to change inputs on the Digital Solution preamp processor For example if you want to play the DVD player push the DVD button on the top row The Digital Solution preamp processor will switch to the DVD input if it is on and the buttons on the DR 3 remote will be set to operate the DP 1 CD DVD player The top buttons bordered by the gold box are multi function buttons That is they can select more than one input Press the DVD 6CH button once and it selects the DVD input on the pre amp processor and allows the DR 3 to act as the remote for the DP 1 CD DVD player Press it a second time and the DS preamp switches to the 6CH Analog input for a DVD Audio or multi chan SACD player What these buttons can t do is select more than one set of remote codes You can program ONE device per Source button Don t worry it isn t very likely that you are going to have both a digital and an analog cable tuner or two DVD players hooked up to your system Of course before the DR 3 can operate any device other than the DS preamp processor and DP 1 CD DVD player you have to insert the device s remote codes into the DR 3 See page 7 for instructions on how to program and use this remote for other devices IMPORTANT NOTE The VOL SURROUND MODE MUTE SUB and SUB buttons are permanently assigned to Digital Solution preamp processor functions No matter what other device
22. iny buttons For control of the rarely used functions of the Digital Solution preamp processor and the other equipment in your system you ll have to use their dedicated remotes If you can t find them look under the sofa cushions they re probably there All of the buttons except for the CODE SAVE CNCL LEARN LIGHT MACRO VOL UP VOL DOWN SURROUND MODE MUTE SYSTEM POWER SUB SUB and the eight MODE buttons have learn functions and can learn the commands of other remote control devices POLK AUDIO LIMITED WARRANTY Polk Audio Inc warrants to the original purchaser only that the DR 3 Remote Control the Product will be free from defects in material and workmanship for a period of three 1 year from the date of original retail purchase from a Polk Audio Authorized Dealer However this Warranty will automatically terminate prior to the expiration if you sell or otherwise transfer the Product to any other party The original retail purchaser shall hereinafter be referred to as you To allow Polk Audio to offer the best possible warranty service please fill out the Product Registration Card s and send it to the Factory at the address provided on the Product Cards s within ten 10 days of the date of purchase Defective Products must be shipped together with proof of purchase prepaid insured to the Polk Audio Authorized Dealer from whom you purchased the Product or to the Factory at 2550 Britannia Boulevard
23. n for two seconds to save the programmed information The orange status light flashes twice The Source Device button light will turn off www polkaudio com PROGRAMMING THE REMOTE Erasing a Learned Command From a Button NOTE You have 20 seconds to perform each step If the source button light goes off you need to back up a step and do it again You can exit by pressing the CNCL cancel button at any time in the process 1 Press and hold the LEARN button for two seconds The status light at the top left of the remote will glow orange 2 Press the Source Device associated with the button you wish to erase The Source Device button light will turn on 3 Press the button that is to be erased The orange status light will flash continuously and the Source Device button will turn off 4 Press the LIGHT button The status light will flash twice then turn to a steady orange The Source Device button will turn on 5 Repeat from Step 3 for any other buttons to be erased in the selected device mode 6 To save your changes press the SAVE button The orange status light will flash twice and then turn off The Source Device button will turn off To Erase All the Learned Commands in One Source Device Mode NOTE You have 20 seconds to perform each step If the source button light goes off you need to back up
24. nge modes is counted as one command 5 Press the SAVE button to store the commands The red status light and the Source button lights will blink twice and then turn off to confirm the program To Erase a Macro Sequence Follow the above Steps 1 2 3 and 5 without going through Step 4 12 Polk Customer Service 800 377 7655 polkaudio SURROUND MACRO OPERATION Macro Sequence Programming Example Confused Don t worry it isn t as bad as it looks Let s walk you through a hypothetical Macro sequence to show you how it works In this example we are programming the DVD source Macro button to turn on the TV the Digital Solution system and the DVD player as well as select the DVD player as the source to view In this case we are assuming that you have programmed the TV codes into the CBL Source Device 1 Press and hold the CODE button for two seconds The status light at the top left of the remote will glow red Press the DVD Source button The DVD Source button will light up Press the MACRO button The red status light and the DVD button lights will blink once 4 Press the CBL Source button Press the SOURCE POWER button to select the TV s power command 6 Press the SYSTEM POWER button to select the Digital Solution s power command 7 Press the DVD source button 8 Press the SOURCE POWER button
25. rol New commands can be taught to any button except the eight Source Device buttons at the top of the remote and the LIGHT MACRO LEARN CODE SAVE CNCL MUTE SURROUND MODE VOL UP VOL DOWN SUB SUB and SYSTEM POWER buttons The remote control provides visual feedback via the status light that is located at the top left of the remote control and the Source Device buttons The status light glows in three colors red orange and green These lights will assist you in programming in the learning section of the remote control NOTE You have 20 seconds to perform each step If the source button light goes off you need to back up a step and do it again You can exit the learning mode by pressing the CNCL cancel button at any time in the process Quick Instructions Place the DR 3 remote and the original remote controls on a table pointing toward each other as shown in the illustration Beooeg POG ZIOA ee o Press LEARN for two seconds Select device type with source buttons Push button to be taught on the DR 3 Push and hold the button on other remote Wait for green light Release button amp press hold it again until green light blinks release Repeat steps 3 6 for other buttons Press SAVE Start from the beginning for each device oun FB WY Detailed Instructions Place the DR 3 remote and the original remote controls on a table pointing towards each other as
26. th DVD CD VCR TIVO type players this button acts as a fast forward or forward button For DSS cable boxes TVs and the Multi room function of the Digital Solution system it acts as the right navigation button for on screen displays 13 STOP v With DVD CD VCR and TIVO type players this button acts as the Stop button For DSS cable boxes TVs and the Multi room function of the Digital Solution system it acts as the Down navigation button for on screen displays 14 015 CLEAR Acts as the Clear command for CD and DVD players Acts as the Record button for all recording devices such as VCR TIVO etc The little red dot means record This button has no function with the Digital Solution preamp processor 15 This button opens and closes the disc drawer of CD and DVD players It acts as the TV VCR input toggle switch on TVs and VCRs and other video devices It has no function with the Digital Solution preamp processor 16 Numeric Keypad Acts just like the number keypad on all other devices These buttons have no function with the Digital Solution preamp processor The 10 button acts as the Previous Channel function on cable boxes and TVs With CD players it acts as the Repeat button 17 SUB and SUB These buttons raise and lower the volume of the Digital Solution subwoofer just like the SUBWOOFER but tons on the DR 1 amp DR 2 remotes The function of these buttons does not change when
27. the LEARN button again for 10 seconds The Status light will flash red continuously The status light will then flash green once orange once then turn off indicating that all of the learned commands in all of the Source Device modes on the remote control have been erased Restoring Factory Programming If you want to restore the DR 3 to it s original programming and oper ation press the LIGHT and POWER buttons simultaneously for 10 seconds The red status light will blink while the remote is resetting It will confirm the reset by blinking green and then orange www polkaudio com E sou polkaudio 11 MACRO OPERATION Programming the Macro Button The MACRO button can send out a sequence of up to 20 commands with one button press It can be programmed for up to eight Source button macros and perform multi step operations with just one button push For example you can program the MACRO button to turn on the TV turn on the DS system turn on the DVD player select the correct Video input and open DVD drawer with the push of one just button Each Source Device button can have an associated Macro program That means you can set up as many as 8 Macros You cannot set up two different Macros for the same Source Device button even though the top row buttons can select two inputs Let s give you an example the 6CH DVD Source Device button can sel
Download Pdf Manuals
Related Search