Plasmon MOD 910 User's Manual
Contents
1. Das Ger t muss von hinten bel ftet werden Das Ger t darf keine Luft von vorne ansaugen Ein minimaler Luftfluss von 3CFM 28dm min ist erforderlich Wenn m glich sollten keine Ger te direkt ber dem 009101 installiert werden Pr caution thermique d emploi pour le lecteur MOD910 Un refroidissement d air forc dans le lecteur est n cessaire au bon fonctionnement de l appareil doit pr venir toute surchauffe et doit faire partie int grante du syst me lors de son int gration Veuillez trouver ci dessous toutes les recommandations observer lors de l installation du M OD910 Ne pas recouvrir ni obturer les syst mes d a ration du lecteur Lacirculation d air doit toujours tre faite de l arri re vers l avant du lecteur L air forc par l arri re doit mettre le lecteur en pression pour pr venir toute introduction d air par l avant e V rifier que le flux d air est au minimum de 3 CFM Sipossible ne pas installer d autre syst me imm diatement au dessus du 00910 97705183 910 User Manual Laser Product Class 1 Laser Product The optical drive mechanism contained in this unit is certified to comply with DHHS rule 21 CFR Chapter 1 Sub chapter J in effect as of the date for manufacture This optical drive mechanism is classified as a Class 1 laser product to EN 60825 and there is no hazardous laser radiation with the safety protection Use of controls or adjustments o2. Serial N umber Description of failure System information which may include Computer type and SCSI adapter type Software configuration in DOS this will be the CONFIG SYS and AUTOEXEC BAT file Type of device driver being used Software and Driver U pdates Ww Do you have the latest revisions El Contact your supplier for firmware or driver updates 97705183 910 User Manual Service on the unit There is no prescribed service for the unit However to ensure optimum performance the unit should operate in as clean an environment as possible where contaminants do not enter the unit Should the unit require cleaning do NOT attempt to open the drive but contact your supplier Microsoft Operating Systems and Optical support A an 97705183 A Microsoft have confirmed that their NT operating system versions 3 51 and 4 0 do not currently FULLY support any WORM or Rewritable Optical media 512 1024 2048 or 4096 bytes per sector or drives under Fat or NTFS File Systems NT using FAT or NTFS only supports Optical if the drive and media act as a Magnetic Hard Drive Type 0 Device Windows NT will support both WORM and Rewritable Optical media when used with another File System such as Plasmon Drive M anager for NT FAT and NTFS with full Optical support are being looked into for a future release of NT from Microsoft Microsoft have committed that Windows 95 will read and write Rewritable
3. V MANUAL Storing More Of Your Digital World Absolutely Plasmon 910 User Manual Copyright Copyright 2000 Plasmon Data Limited No part of this publication may be reproduced stored in retrieval system or transmitted in any form or by any means without the prior written consent of Plasmon Data Limited Trademarks TM All trademarks that may be contained within this publication are registered with their respective companies Changes The material in this manual is for reference only and is subject to change without notice While reasonable efforts have been taken in the preparation of the material contained in this manual Plasmon Data Limited assumes no liability resulting from any errors or omissions or from the use of material contained herein Cautions CAUTION Warnings related to directions which could put the operator and the drive at risk of damage VORSICHT Warnungen welche sich auf die Sicherheit des Benutzers sowie die des Laufwerks beziehen ATTENTION Le non suivi des remarques attentions et indications de ce mode d emploi peut engendrer des risques l op rateur ainsi qu au mat riel lui m me NOTE Information relating to important suggestions CAUTION Warnings relating to directions which could put the operator and drive at risk of damage Br 7 TIP Hints to achieve the optimum performance from your drive a Release December 2002 977
4. Contains 97705183 P9100W 9 1GB WORM MO media 4096 bytes sector P9100E 9 1GB Rewritable M O media 4096 bytes sector P8600W 8 6GB WORM media 2048 bytes sector P8600E 8 6GB Rewritable M O media 2048 bytes sector RS 184 5113 5 x Replacement Filters external drive only Contacting Plasmon Should there be a need for further support other than what this manual provides please contact one of these two technical support locations To obtain technical support in the United States Plasmon 1 877 585 6793 Technical Support 1 719 593 4192 fax e mail support plasmon com World Wide Web www plasmon com To obtain technical support in Europe Plasmon Technical Support 44 0 1763 262 963 44 0 1763 264 444 e mail support plasmon co uk World Wide Web www plasmon com International Calls 1 719 593 4437 1 719 593 4192 fax European Headquarters Plasmon Data Limited Whiting Way Melbourn Hertfordshire SG8 6EN Tel 44 0 1763 262963 Fax 44 0 1763 264444 Email sales plasmon co uk United States Plasmon 4425 ArrowsWest Drive Colorado Springs CO 80907 3489 Tel 719 593 7900 Fax 719 599 8713 lt Storing Of Your Digital World Absolutely
5. Le m canisme de lecture optique composant cette unit est certifi conforme la norme DHHS r gle 21 chapitre 1 sous chapitre en vigueur la date de fabrication Ce m canisme de lecture optique fait partie des produits laser de classe 1 conform ment la norme EN 60825 et ne produit aucun rayonnement nocif gr ce son dispositif de s curit Toutes v rifications r glages ou proc dures autres que ceux mentionn s dans ce guide d utilisation peuvent vous exposer un rayonnement nocif Ne jamais ouvrir le bo tier du lecteur et vitez tout contact avec les composants internes du produit Lorsque l appareil est sous tension n essayez jamais de regarder l int rieur de l unit par l ouverture du panneau frontal Sp cification du laser M canisme laser de classe 1 Puissance laser aucun rayonnement nocif n est mis gr ce au dispositif de s curit int gr l unit 97705183 910 User Manual Unpacking Packing 1 2 3 d 97705183 A General precautions N ote the following precautions in order to maintain the performance and reliability of the drive Open the package with particular care Do not expose the unit to excessively dusty environment The unit contains components that can be destroyed by static electricity Follow the guidelines below for internal unit Use an anti static mat and ground yourself when handling the internal unit
6. SCSI HOST CONTROLLER DB1 2 SCSI HOST CONTROLLER DB2 28 SCSI HOST CONTROLLER DB3 29 SCSI HOST CONTROLLER DB4 30 SCSI HOST CONTROLLER DB5 3l SCSI HOST CONTROLLER DB6 32 SCSI HOST CONTROLLER DB7 33 SCSI HOST CONTROLLER DBP 34 SCSI HOST CONTROLLER GROUND 35 GROUND 36 GROUND 37 TERM PWR 38 SCSI HOST CONTROLLER GROUND 39 GROUND 40 ATTN 41 SCSI HOST GROUND 42 BSY 43 SCSI HOST CONTROLLER ACK 44 SCSI HOST RST 45 SCSI HOST MSG 46 CONTROLLER SEL 47 SCSI HOST CONTROLLER C D 48 CONTROLLER REQ 49 CONTROLLER 1 0 50 CONTROLLER 97705183 910 User Manual SCSI Interface connector signal names MOD910I 50 WAY IDC CONNECTOR SIGNAL NAM E PIN NUM BER SIGNAL SOURCE 080 2 SCSI HOST CONTROLLER DB1 4 SCSI HOST CONTROLLER DB2 6 SCSI HOST CONTROLLER DB3 8 SCSI HOST CONTROLLER 084 10 SCSI HOST CONTROLLER DB5 12 SCSI HOST CONTROLLER DB6 14 SCSI HOST CONTROLLER DB7 16 SCSI HOST CONTROLLER DBP 18 SCSI HOST CONTROLLER GROUND 20 GROUND 22 GROUND 24 TERM WR 26 SCSI HOST CONTROLLER GROUND 28 GROUND 30 ATTN 32 SCSI HOST GROUND 34 BSY 36 SCSI HOST CONTROLLER ACK 38 SCSI HOST RST 40 SCSI HOST M SG 42 CONTROLLER SEL 44 SCSI HOST CONTROLLER C D 46 CONTROLLER REQ 48 CONTROLLER 1 0 50 CONTROLLER 97705183 910 User Manual Appendix G Accessories Media Filter Pack kit PartNo
7. run up to a maximum ambient temperature of 30 C with air filters 97705183 910 User Manual General Description 97705183 The MOD910 is a high performance high capacity optical disk drive that offers recording on rewritable CCW WORM media that is ISO compliant The MOD910 reads and writes to 9 1GB 8 6GB 5 2GB 4 8GB 4 1GB 2 6GB and 2 3GB rewritable WORM and DOW disks and offers read compatibility to earlier 150 standard 1 3GB 1 2GB 650MB and 600MB media so protecting any existing investment in storage The MOD910 also forms the basis for the range of Plasmon M agneto Optical jukeboxes providing further performance increases MOD910 has been designed to give fast solid and reliable disk exchanges Please take the time to study this manual to become familiar with operating the unit as well as prescribed service The main features of the M OD910 drive are 9 168 4 55GB per side of storage on rewritable and CCW WORM disks Half height unit Reads 594M B and 650M B disks as well as 1 2GB 1 3GB 2 3GB 2 6GB 4 1GB 4 8GB and 5 2GB media as used in earlier drives in addition to read amp write compatibility to 2 3GB and 2 6GB disks Data cache of 8M B for write and read operations Effective seek time of 25ms Synchronous data rates up to 10 M Bytes sec Universal AC supply operates from 100 to 240 volts M OD910E lt lt RUSSE 910 User Manual SCSI Connections Th
8. static wrist strap should be used to avoid possible damage from static electricity Ensure that the power connector is correctly wired Check that the power is within the unit s specification Ensure that adequate ventilation is provided GETTING STARTED Operation amp Installation Instructions External Drive 97705183 A Do not apply power yet Set the SCSI ID of the unit via the DIP switch on the rear of the unit see Appendix B and C Connect the SCSI interface cable between the computer and the drive unit If the drive is the last unit on the SCSI interface install the supplied terminator in the unused SCSI connector Apply power to the unit Insert a disk cartridge into the drive gently pushing it into the drive until itis power loaded The motor will start and after a few seconds the drive will be ready for use When the eject button is pressed the cartridge will electronically eject from the drive after a short delay 910 User Manual Externes Laufwerk Noch nicht einschalten M an stellt die SCSI ID des Ger ts am hinterem DIP Schalter ein siehe Anhang und Verbinden Sie den Rechner und das Laufwerk mit dem SCSI Kabel Falls das Laufwerk das letzte Ger t in der SCSI Kette ist installiert man den mitgelieferten Begrenzer Terminator in den leeren SCSI Sockel Schalten Sie das Ger t ein Man schiebt eine Disk in das Laufwerk bis das Gerat sie von selber animmt Der Motor f ngt da
9. 05183 A 910 User Manual FCC Compliance Statement NOTE This equipment has been tested and found to comply with the e limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by switching the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures a Reorient or relocate the receiving antenna a Increase the separation between the equipment and receiver lt Connect the equipment into an outlet on a circuit different from that to A which the receiver is connected 0u Consult the dealer or an experienced radio TV technician for help The compliance of this unit to the FCC rules is not subject to any special S accessories which are not readily available through normal dealer channels The drive is in conformity with the directive and low voltage directive CAUTION Any modifications or changes made to this equipment not expressly approv
10. 8 Internal Drive Dr r gean 9 Prechecks before Service 10 Placing a service 10 Service on the 11 Microsoft Optical Systems and Optical Support 11 Disk Cartridge 12 Appendix A awk et te ER DR ias 13 Component Location 13 Appendix B eon dial Wa a E exe s 15 Function Connector Pin Description 15 Appendix ee xw dir kk y de A ere AP C RE E 16 SCSI Device 00 55 16 Appendix TA 17 Drive Option 17 AppendbCE tits tat a G y bal ha ab a 18 Main Specifications 18 E hn n n EE 19 SCSI Interface connector signal names 19 MOD910E SCSI CONNECTOR 19 009101 50 WAY IDC CONNECTOR 20 Appendix gt n lac Pe xe e eng 21 Accessories and 5 21 97705183 910 User Manual Owners Record AS The model and serial number of the drive you have just purchas
11. Always be sure to handle the internal unit only by the frame and do not touch any electrical components Unpacking Internal Unit When moving the unit to an environment where there is a significant difference in temperature let the unit remain in its packaging for at least two hours Find a flat soft surface for unpacking keeping the box upright Do not apply excessive force to the unit when removing the shock absorbing material or to the surfaces and interface connector when removing the anti static bag Unpacking External Unit When moving the unit to an environment where there is a significant difference in temperature let the unit remain in its packaging for at least two hours Find a flat soft surface for unpacking keeping the box upright 4 5 910 User Manual Packing Pack the unit after you have removed the disk Put the device in the anti static or plastic bag It is desirable to use the original shock absorbing material and packing box used when the unit was delivered to you If not use a box with a shock absorbing structure that will prevent direct impacts to the device In the case of the internal unit protect the surfaces and interface connector against possible damage and use an anti static bag Transportation Transport the unit in a well packaged condition with the upside facing up Transport the unit as little as possible after unpacking always using the shock absorbing materi
12. Optical media only when it has been formatted with third party software WORM media is not supported and requires third party software UDF 1 02 file formats can be read by Windows 2000 without any additional driver software which gives guarantees of future read compatibility Customers using NT with Plasmon M ultitasking M anager have no need for any action For details of Optical support in future products from M icrosoft please contact them direct 910 User Manual Disk Cartridge Notes 1 Never open the shutter to look at the disk The shutter is provided for protection against dust dirt and other contaminants 2 Avoid subjecting the cartridge to sudden shock or impact 3 When the write protect window is open the disk is in a read only mode of operating E ex du Read write enable Write protect 97705183 910 User Manual Appendix A Component Location MOD910E Plasmon S ES 910 E Busy indicator A Power light Cartridge eject D Emergency eject m 1 8a SCSI connectors SCSI ID selector Fan optional filter 2 Power connector AC on off switch gt 97705183 A 910 User Manual Appendix A continued Component Location MOD910I OPTION SWITCHES EJECT BUTTON FUNCTION ON PIN 1 N Appendi
13. P7 SW4 Fitted ON J P8 N C N C J P9 SW5 Fitted ON J P10 SW6 N C OFF J P11 Fitted Fitted 97705183 A 910 User Manual Appendix D Drive Option Switches The MOD910 provides eight switches which permit the user to define certain drive operations or interface features Optional Switch Description Switch Number 1 Reserved 2 Reserved 3 Disable Command Eject S501 4 Reserved 5 Enable Library I F M ode 6 Reserved 7 Disable Write Cache 8 Disable Auto Spin up 1 Reserved 2 Reserved 3 Reserved 5502 4 Reserved 5 Disable SCAM Selection 6 Reserved 7 Enable Fast SCSI 8 Enable Write Cache for Write and Verify Command Option Switch Function NOTE The MOD910I is shipped with the forced verify on write operation enabled NOTE The drive is shipped with write caching enabled by default In data critical applications it may be necessary to disable write caching This may be achieved using Adaptecs SCSI EXPLORER program under the windows environment Programmers may also access this function through the M ode Page Settings 97705183 Appendix E 910 User Manual Main Specifications Access times Average seek 4 full stroke M otor start M otor stop Rotational speed Data transfer rates User sustained write read Burst asynchronous Burst synchronous Buffer size M TBF Power On Hours Environmental Operatin
14. al to avoid impact and vibration When carrying the unit after unpacking keep it in the horizontal plane Storage Use the moisture proof packing material for storage The storage environment should meet the non operating environmental requirement as specified in Appendix E Do not expose the unit to radical changes in temperature which could cause condensation 97705183 910 User Manual Table of Contents LE LOST Trademarks A eg b xx kay n RUN ES i Changes iia en Se E e RN RUE FCC Compliance ii Thermal Precautions iii Laser Product EE iv Class A Laser Pro U e bala a day b e iv Laser Specification isses Rer pacer a ER RUD a un kak iv Unpacking 0 vi Owners Record ER XLV kk a kk C e kk kaka kk kk de 2 see du ERE 2 General Description 3 SCSI Connections cere cx RE Ce RR kk Hr 4 SCSI Identifier ona eee Red nn 6 General Precautions for MOD910E 7 GETTING STARTED 8 Operation Installation Instructions 8 External DIVE sata Db M Gil Wa den
15. e external drive is equipped with two Micro D 50 way connectors on the rear panel These are for the SCSI in and SCSI out if there are additional devices connected A SCSI interface cable needs to be terminated at each end of the line one terminator being on the last device in the chain and the other terminator is usually on the host computer or adapter card a M icro D SCSI Terminator is supplied external drive only a Refer to the documentation supplied with your SCSI card or computer N system should you need to check the computer termination In normal d circumstances this will usually be enabled The two ways of connecting SCSI devices are shown below Fig 1 External Drive Connection Fig 2 Internal Drive Connection Fig 1 External Drive Connection 3 1 Switch block SCSI ID setting 2 SCSI connector for additional devices or terminator if last in chain 3 SCSI cable If there are also internal devices on the same SCSI card then the SCSI Ja adapter card must have its on board termination disabled 97705183 A 910 User Manual Fig 2 Internal Drive Connection AAN 1 DC Power Connector 2 J umper block for SCSI ID settings 3 50 way SCSI cable note pin 1 orientation SCSI adapter on board termination must be disabled Refer to the If internal devices are also to be connected to the SCSI card t
16. ed are ka located on the underside of the unit Please record them below and 4 refer to them should you need to call your supplier for service or technical support External or the top of the drive Internal 1 Extern oder der obere Teil des Laufwerks Intern MOD910 Serial No 33 Keep this manual for reference purposes should any switch setting need to be altered Warning Use of controls or adjustments other than those specified herein may result in hazardous laser radiation exposure This product may only have the cover removed for service or repair by a qualified and approved service site Vorsicht Anwendung der Kontrollen oder Einstellungen dieses Ger tes anders wie hier vorgeschrieben konnen zu sch dlicher Strahlenausetzung fuhren Das Geh use darf nur von einer qualifizierten Reparaturwerkstatt entfernt werden Important Toutes proc dures de v rification d alignement ou de tests autres que celles sp cifi es dans ce manuel peuvent entrainer une exposition dangereuse au rayon laser Dans tous les cas ce produit ne doit avoir le capot de protection laser ouvert que dans les centres de r paration agr s par le constructeur Air Filters The M OD910E external drive is shipped without Air Filters The drive has been designed with ducted air cooling air should not get into the body of the drive Air Filters are provided for particularly dusty or dirty environments Please be advised that the drive will
17. ed by the PLASM ON group of companies may void the authority to operate this equipment in its intended installation WARNUNG Die Vollmacht das Ger t in der vorgeschriebenen Weise zu betreiben wird dann ung ltig wenn an dem Laufwerk Ver nderungen vorgenommen werden die nicht von PLASMON genehmigt wurden 97705183 A 910 User Manual ATTENTION Toute modification ou changement fait sur cet quipement et non express ment approuv par Plasmon peut engendrer des disfonctionnements irr versibles et rendre son installation impossible Thermal Precautions for the MOD910l Forced air cooling is required throughout the drive to prevent overheating of the drive and must be provided as part of the system integration The dew n are precautions that should be observed when installing the 009101 Do not cover the ventilation slot on top of the drive Airflow should be from the rear of the unit Air should not be drawn into the front of the unit Ensure that a minimum airflow of 3 CFM is provided e f possible try to ensure that there is no device installed immediately above the M 9101 Thermale Vorsichtsmassnahmen fur das MOD910I Zwangsluftk hlung ist erforderlich da es das Uberhitzen des Laufwerks verhindert Die K hlung muss in das System integriert werden Die folgenden Vorsichtsmassnahmen m ssen bei dem Einbau des 009101 beachtet werden Die Ventilations ffnung auf dem Laufwerk darf nicht abgedeckt werden
18. g temperature Non operating temperature Operating humidity Non operating humidity Operating vibration 5 350Hz Operating shock no damage Non operating shock Electrical Operating voltage Power requirements Structure Dimensions WxHxD in mm Weight Drive orientation Warranty 0D910e 25 ms 2 5 seconds 2 2 seconds 3000 3300 3600 RPM 3 07 to 6 14 M B second 3 M B second 10 M B second Fast SCSI enabled 8 MB 100 000 5 to 40 30 to 60 10 to 90 5 to 90 non condensing 0 00015 GHz or 0 014 m s 30G or 294 m s 3ms half sine 896 or 873 m s 3ms half sine 100 to 240V AC 50 60Hz 0 5 228 x 66 x 276 39 Kg horizontal one year pars and labour return to base MOD910i 25 ms 2 5 seconds 2 2 seconds 3000 3300 3600 RPM 3 07 to 6 14 M B second 3 MB second 10 M B second Fast SCSI enabled 8MB 100 000 5 to 45 C 30 to 60 10 to 90 5 to 90 non condensing 0 00015 GHz or 0 014 m s 306 or 294 m s 3ms half sine 896 or 873 m s 3ms half sine 5V 5 12V 5 5V 20 Max 0 84 Typ 12V 3 04 0 9A 146 x 41 3 x 203 15 Kg horizontal vertical one year par and labour return to base 97705183 A 910 User Manual Appendix F SCSI Interface connector signal names MOD910E SCSI CONNECTOR SIGNAL NAM E PIN NUM BER SIGNAL SOURCE 080 26
19. hen the lt gt documentation that accompanies the SCSI adapter 97705183 910 User Manual SCSI Identifier Each device on a SCSI bus requires a unique address to be set which maybe in the range of 0 to 6 as address 7 is usually reserved for the host computer address The 00910 is shipped with a default address of 1 which will usually suffice in most cases General Please refer to diagram on Appendix C Precautions for MOD910E X A x x Never plug or un plug any connectors or cables from the device on the SCSI bus whilst power is applied to either host computer or any devices attached Do not use the unit under the following operating environments Places with high humidity Exposed to direct sunlight Locations subject to excessive shock or vibration Do not cover ventilation slots as these are provided for cooling Do not place the drive near a printer Never attempt to disassemble the unit Never touch the surface of a recordable disk Do not allow any foreign object or liquid to enter the unit Always remove the disk before moving the unit This will ensure that the optical head is securely positioned for shipping Keep the packaging material should the unit have to be transported 97705183 910 User Manual Additional Notes for Internal Models X Never connect disconnect unit to from SCSI bus with power on any units including host computer V When handling the unit an anti
20. ins by removing the jumper will force the drive not to Verify after Write unless specified under software A8 B8 Disable Manual Shorting the pins disables the eject button Eject operation Default Open 5 A9 B9 Enable Fast SCSI Shorting the pins enables Fast SCSI mode Default Closed 6 10 B10 Device When the pins open the drive responds as an Optical Memory Device type 7 Default Shorting the pins forces the drive to respond as a Direct Access Device type 0 A11 B11 Enable Shorting the pins invokes the internal SCSI Termination active terminator With the pins open default Termination is disabled 12 B12 Terminator These pins supply 5V DC through an isolation Power diode for SCSI terminator power to the SCSI bus TERM PWR line Shorting the pins enables SCSI TERM PWR signal default Leaving them open disables 97705183 910 User Manual Appendix C SCSI Device Address Jukebox Connector SCSI ID SCSI Drive J P1 or SW3 J P2 or SW2 or SW1 Address 0 OFF OFF OFF 1 OFF OFF ON 2 OFF ON OFF 3 OFF ON ON 4 ON OFF OFF 5 ON OFF ON 6 ON ON OFF 7 0N ON ON Drives are set up to 101 as default Default Jumpers on external and internal units J umper Switch internal external J P1 SW3 N C OFF J P2 SW2 N C OFF J P3 SW1 Fitted ON J P4 N C N C J P5 N C N C J P6 N C N C J
21. ion Opening the enclosure and changing these settings must only be carried out by a qualified service engineer Drive The internal drive can be used in both the vertical and horizontal plane The external drive must only be used in the horizontal plane Attaching screws are supplied with the unit The screws are M3 x 8 mm and the fixing plate should be within the range of 1 5 to 2 5 mm which includes the washer Included with internal drives is a 50 way flat IDC cable with 2 connectors for connection to the SCSI adapter Note for correct orientation of the flat cable when installing Pin 1 is usually identified by a red stripe on the edge of the cable and connectors have a small arrow by pin 1 Connect the internal power connector in your computer to the drive making sure that the orientation is correct 910 User Manual Prechecks before Service Call Z Disk cannot be inserted Is power on Is the disk orientated correctly Is the disk the correct type D cn Access Failure Is the cartridge inserted Is the SCSI ID set correctly Are the SCSI bus terminated correctly Is the cartridge set to write protect Are other devices on the SCSI bus operating normally Is the software device driver installed correctly N o o N Placing a service call Contact your supplier or service company They will probably require the following information Where purchased Date of Purchase
22. nn zu laufen an und nach wenigen Sekunden ist das Laufwerk anwendungsf hig Wenn man den Eject Knopf dr ckt wirft das Ger t die Disk nach ein paar Sekunden wieder aus Lecteur Externe Ne connectez pas encore votre mat riel Configurez l adressage SCSI au moyen du dip switch en panneau arri re de l quipement voir appendice B et C Connectez le c ble SCSI entre l ordinateur et l unit Si l unit est la derni re de la chaine SCSI veillez installer le terminateur sur le connecteur SCSI libre Alimentez l unit et mettez la en marche Ins rez avec pr caution une cartouche dans le lecteur jusqu la voir automatiquement aval e par l unit Le moteur du disque va alors commencer tourner et apr s quelques secondes le lecteur est pr t l utilisation Lorsque le bouton ject est press la cartouche sera ject e apr s quelques secondes 97705183 910 User Manual Notes Internal 97705183 A If you need to use the emergency eject pinhole make sure that the unit is powered off and that the disk has stopped its rotation 20 30 seconds after power off If the SCSI ID is changed with the unit powered ON then power must be removed and reapplied for the new ID to take effect Before moving the drive always ensure that the optical disk cartridge is removed The drive has various functions that may be altered from their defaults if required These are outlined in the MOD910I sect
23. r performance of procedures other than those specified herein may result in hazardous radiation exposure Never open the enclosure or touch the parts internal to the product When the power switch is on do place your eyes close to the front panel opening to look into the unit Laser Specification Class 1 LASER mechanism Laser Power No hazardous radiation is emitted with the safety protection of the unit 97705183 A 910 User Manual Laser Produckt Klasse 1 Laser Produkt Der optische Laufwerksmechanismus welcher sich in diesem Gerat befindet entspricht der DHHS Regel 21 Kapitel 1 Nebenkapitel J wirkend ab Herstellungs Datum Dieser optische Laufwerksmechanismus wird entsprechend EN 60825 als Klasse 1 Laser Produkt klassifiziert und gibt mit Sicherheits Schutz keine sch dliche Strahlungen ab Anwendung der Kontrollen oder Gebrauch dieses Ger tes anders wie hier vorgeschrieben k nnen zu sch dlicher Strahlenausetzung f hren Das Geh use des Ger tes darf nicht ge ffnet werden auch d rfen die Innenteile unter keinen Umst nden angefasst werden Wenn das Ger t eingeschaltet ist darf man nicht versuchen durch das Offnen der forderen Klappe in das Laufwerkinnere hinein zu sehen Laser Beschreibung 97705183 Klasse 1 Laser M echanismus Laser Antrieb Mit Sicherheitsschutz gibt Gerat keine sch dliche Strahlungen ab 910 User Manual Produit laser Produit laser de classe 1
24. x B amp C PIN 1 Ol EECH SCSI PIN 1 FLAP FOR AIR DUCTING 97705183 A 910 User Manual Appendix B Function Connector Pin Description see appendix A for connector location Switch Pins Function Description 3 1 1 SCSIID 2 See Appendix C to set SCSI ID 2 A2 B2 SCSI ID 1 See Appendix C to set SCSI ID 1 A3 B3 SCSIID 0 See Appendix C to set SCSI ID A4 B4 Disable SCSI When the pair of pins is open the drive Parity performs SCSI parity checking default Shorting the pins with a jumper forces the drive to perform the SCSI parity checking A5 B5 Disable Write When the pair of pins is open the drive Cache performs write back caching default Shorting the pins with a jumper forces the drive NOT to perform the write back caching A6 B6 Disable Auto When the pair of pins is open the drive Spin up performs an automatic spin up upon media loading default Shorting the pins with a jumper forces the drive NOT to perform the automatic spin up 4 B7 Force Verify Shorting the pair of pins forces the drive to for Write perform a Write and Verify operation Whenever the host issues a WRITE command default Opening the p
Download Pdf Manuals
Related Search